- 08 Sep, 2020 25 commits
-
-
Joel Stanley authored
Often the firmware will guard out cores after a crash. This often undesirable, and is not immediately noticeable. This adds an informative message when a CPU device tree nodes are marked bad in the device tree. Signed-off-by: Joel Stanley <joel@jms.id.au> [mpe: Use an eye-catcher that's less likely to get us in trouble] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190801051630.5804-1-joel@jms.id.au
-
Leonardo Bras authored
On LoPAR "DMA Window Manipulation Calls", it's recommended to remove the default DMA window for the device, before attempting to configure a DDW, in order to make the maximum resources available for the next DDW to be created. This is a requirement for using DDW on devices in which hypervisor allows only one DMA window. If setting up a new DDW fails anywhere after the removal of this default DMA window, it's needed to restore the default DMA window. For this, an implementation of ibm,reset-pe-dma-windows rtas call is needed: Platforms supporting the DDW option starting with LoPAR level 2.7 implement ibm,ddw-extensions. The first extension available (index 2) carries the token for ibm,reset-pe-dma-windows rtas call, which is used to restore the default DMA window for a device, if it has been deleted. It does so by resetting the TCE table allocation for the PE to it's boot time value, available in "ibm,dma-window" device tree node. Signed-off-by: Leonardo Bras <leobras.c@gmail.com> Tested-by: David Dai <zdai@linux.vnet.ibm.com> Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200805030455.123024-5-leobras.c@gmail.com
-
Leonardo Bras authored
Move the window-removing part of remove_ddw into a new function (remove_dma_window), so it can be used to remove other DMA windows. It's useful for removing DMA windows that don't create DIRECT64_PROPNAME property, like the default DMA window from the device, which uses "ibm,dma-window". Signed-off-by: Leonardo Bras <leobras.c@gmail.com> Tested-by: David Dai <zdai@linux.vnet.ibm.com> Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200805030455.123024-4-leobras.c@gmail.com
-
Leonardo Bras authored
>From LoPAR level 2.8, "ibm,ddw-extensions" index 3 can make the number of outputs from "ibm,query-pe-dma-windows" go from 5 to 6. This change of output size is meant to expand the address size of largest_available_block PE TCE from 32-bit to 64-bit, which ends up shifting page_size and migration_capable. This ends up requiring the update of ddw_query_response->largest_available_block from u32 to u64, and manually assigning the values from the buffer into this struct, according to output size. Also, a routine was created for helping reading the ddw extensions as suggested by LoPAR: First reading the size of the extension array from index 0, checking if the property exists, and then returning it's value. Signed-off-by: Leonardo Bras <leobras.c@gmail.com> Tested-by: David Dai <zdai@linux.vnet.ibm.com> Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200805030455.123024-3-leobras.c@gmail.com
-
Leonardo Bras authored
Create defines to help handling ibm,ddw-applicable values, avoiding confusion about the index of given operations. Signed-off-by: Leonardo Bras <leobras.c@gmail.com> Tested-by: David Dai <zdai@linux.vnet.ibm.com> Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200805030455.123024-2-leobras.c@gmail.com
-
Jordan Niethe authored
Update the CPU to ISA Version Mapping document to include Power10 and ISA v3.1. Signed-off-by: Jordan Niethe <jniethe5@gmail.com> [mpe: Make sure ISA reference is unique] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200827040556.1783-1-jniethe5@gmail.com
-
Russell Currey authored
As of commit bdc48fa1, scripts/checkpatch.pl now has a default line length warning of 100 characters. The powerpc wrapper script was using a length of 90 instead of 80 in order to make checkpatch less restrictive, but now it's making it more restrictive instead. I think it makes sense to just use the default value now. Signed-off-by: Russell Currey <ruscur@russell.cc> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200828020542.393022-1-ruscur@russell.cc
-
Jordan Niethe authored
The signal handler in the alignment handler self test has the ability to jump over the instruction that triggered the signal. It does this by incrementing the PT_NIP in the user context by 4. If it were a prefixed instruction this will mean that the suffix is then executed which is incorrect. Instead check if the major opcode indicates a prefixed instruction (e.g. it is 1) and if so increment PT_NIP by 8. If ISA v3.1 is not available treat it as a word instruction even if the major opcode is 1. Fixes: 620a6473 ("selftests/powerpc: Add prefixed loads/stores to alignment_handler test") Signed-off-by: Jordan Niethe <jniethe5@gmail.com> [mpe: Fix 32-bit build, rename haveprefixes to prefixes_enabled] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200824131231.14008-1-jniethe5@gmail.com
-
Jordan Niethe authored
As of commit 147c0516 ("powerpc/boot: Add support for 64bit little endian wrapper") the comment in the Makefile is misleading. The wrapper packaging 64bit kernel may built as a 32 or 64 bit elf. Update the comment to reflect this. Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200825035147.3239-1-jniethe5@gmail.com
-
Michael Ellerman authored
The last caller was removed in 2014 in commit fb5a5157 ("powerpc: Remove platforms/wsp and associated pieces"). As Jordan noticed even though there are no callers, the code above in fsl_secondary_thread_init() falls through into generic_secondary_thread_init(). So we can remove the _GLOBAL but not the body of the function. However because fsl_secondary_thread_init() is inside #ifdef CONFIG_PPC_BOOK3E, we can never reach the body of generic_secondary_thread_init() unless CONFIG_PPC_BOOK3E is enabled, so we can wrap the whole thing in a single #ifdef. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200819015704.1976364-1-mpe@ellerman.id.au
-
Michael Ellerman authored
On older CPUs the switch_endian() syscall doesn't work. Currently that causes the switch_endian_test to just crash. Instead detect the failure and properly exit with a failure message. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200819015727.1977134-9-mpe@ellerman.id.au
-
Michael Ellerman authored
If we're running on a CPU without VMX/VSX then don't touch them. This is fragile, the compiler could spill a VMX/VSX register and break the test anyway. But in practice it seems to work, ie. the test runs to completion on a system without VSX with this change. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200819015727.1977134-8-mpe@ellerman.id.au
-
Michael Ellerman authored
This is a test of specific piece of logic in isa207-common.c, which is only used on Power8 or later. So skip it on older CPUs. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200819015727.1977134-7-mpe@ellerman.id.au
-
Michael Ellerman authored
Both these tests use PMU events that only work on newer CPUs, so skip them on older CPUs. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200819015727.1977134-6-mpe@ellerman.id.au
-
Michael Ellerman authored
The DSCR tests fail on systems that don't have DSCR, so check for the DSCR in hwcap and skip if it's not present. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200819015727.1977134-5-mpe@ellerman.id.au
-
Michael Ellerman authored
utils.h provides have_hwcap() and have_hwcap2() which check for a feature bit. Those bits are defined in asm/cputable.h, so include it in utils.h so users of utils.h don't have to do it manually. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200819015727.1977134-4-mpe@ellerman.id.au
-
Michael Ellerman authored
This version of set_dscr() was added for the RFI flush test, and is fairly specific to it. It also clashes with the version of set_dscr() in dscr/dscr.h. So move it into the RFI flush test where it's used. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200819015727.1977134-3-mpe@ellerman.id.au
-
Michael Ellerman authored
On older systems this test takes longer to run (duh), give it five minutes which is long enough on a G5 970FX @ 1.6GHz. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200819015727.1977134-2-mpe@ellerman.id.au
-
Michael Ellerman authored
These platforms don't show the MMU in /proc/cpuinfo, but they always use hash, so teach using_hash_mmu() that. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200819015727.1977134-1-mpe@ellerman.id.au
-
Michael Ellerman authored
This test creates some threads, which write to TM SPRs, and then makes sure the registers maintain the correct values across context switches and contention with other threads. But currently the test finishes almost instantaneously, which reduces the chance of it hitting an interesting condition. So increase the number of loops, so it runs a bit longer, though still less than 2s on a Power8. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200813013445.686464-3-mpe@ellerman.id.au
-
Michael Ellerman authored
This test tries to set affinity to CPUs that don't exist, especially if the set of online CPUs doesn't start at 0. But there's no real reason for it to use setaffinity in the first place, it's just trying to create lots of threads to cause contention. So drop the setaffinity entirely. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200813013445.686464-2-mpe@ellerman.id.au
-
Michael Ellerman authored
Several of the TM tests fail spuriously if CPU 0 is offline, because they blindly try to affinitise to CPU 0. Fix them by picking any online CPU and using that instead. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200813013445.686464-1-mpe@ellerman.id.au
-
Oliver O'Halloran authored
These annoy me every time I see them. Why are they here? They're not even needed for 80cols compliance. Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200818044557.135497-1-oohall@gmail.com
-
Christophe Leroy authored
ftrace_graph_ret_addr() is always defined and returns 'ip' when CONFIG_FUNCTION GRAPH_TRACER is not set. So the #ifdef is not needed, remove it. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/9d11143d4e27ba8274369a926968756917584868.1597643153.git.christophe.leroy@csgroup.eu
-
Christophe Leroy authored
Enable pre-update addressing mode in __get_user_asm() and __put_user_asm() Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/13041c7df39e89ddf574ea0cdc6dedfdd9734140.1597235091.git.christophe.leroy@csgroup.eu
-
- 02 Sep, 2020 15 commits
-
-
Christophe Leroy authored
At the time being, __put_user()/__get_user() and friends only use D-form addressing, with 0 offset. Ex: lwz reg1, 0(reg2) Give the compiler the opportunity to use other adressing modes whenever possible, to get more optimised code. Hereunder is a small exemple: struct test { u32 item1; u16 item2; u8 item3; u64 item4; }; int set_test_user(struct test __user *from, struct test __user *to) { int err; u32 item1; u16 item2; u8 item3; u64 item4; err = __get_user(item1, &from->item1); err |= __get_user(item2, &from->item2); err |= __get_user(item3, &from->item3); err |= __get_user(item4, &from->item4); err |= __put_user(item1, &to->item1); err |= __put_user(item2, &to->item2); err |= __put_user(item3, &to->item3); err |= __put_user(item4, &to->item4); return err; } Before the patch: 00000df0 <set_test_user>: df0: 94 21 ff f0 stwu r1,-16(r1) df4: 39 40 00 00 li r10,0 df8: 93 c1 00 08 stw r30,8(r1) dfc: 93 e1 00 0c stw r31,12(r1) e00: 7d 49 53 78 mr r9,r10 e04: 80 a3 00 00 lwz r5,0(r3) e08: 38 e3 00 04 addi r7,r3,4 e0c: 7d 46 53 78 mr r6,r10 e10: a0 e7 00 00 lhz r7,0(r7) e14: 7d 29 33 78 or r9,r9,r6 e18: 39 03 00 06 addi r8,r3,6 e1c: 7d 46 53 78 mr r6,r10 e20: 89 08 00 00 lbz r8,0(r8) e24: 7d 29 33 78 or r9,r9,r6 e28: 38 63 00 08 addi r3,r3,8 e2c: 7d 46 53 78 mr r6,r10 e30: 83 c3 00 00 lwz r30,0(r3) e34: 83 e3 00 04 lwz r31,4(r3) e38: 7d 29 33 78 or r9,r9,r6 e3c: 7d 43 53 78 mr r3,r10 e40: 90 a4 00 00 stw r5,0(r4) e44: 7d 29 1b 78 or r9,r9,r3 e48: 38 c4 00 04 addi r6,r4,4 e4c: 7d 43 53 78 mr r3,r10 e50: b0 e6 00 00 sth r7,0(r6) e54: 7d 29 1b 78 or r9,r9,r3 e58: 38 e4 00 06 addi r7,r4,6 e5c: 7d 43 53 78 mr r3,r10 e60: 99 07 00 00 stb r8,0(r7) e64: 7d 23 1b 78 or r3,r9,r3 e68: 38 84 00 08 addi r4,r4,8 e6c: 93 c4 00 00 stw r30,0(r4) e70: 93 e4 00 04 stw r31,4(r4) e74: 7c 63 53 78 or r3,r3,r10 e78: 83 c1 00 08 lwz r30,8(r1) e7c: 83 e1 00 0c lwz r31,12(r1) e80: 38 21 00 10 addi r1,r1,16 e84: 4e 80 00 20 blr After the patch: 00000dbc <set_test_user>: dbc: 39 40 00 00 li r10,0 dc0: 7d 49 53 78 mr r9,r10 dc4: 80 03 00 00 lwz r0,0(r3) dc8: 7d 48 53 78 mr r8,r10 dcc: a1 63 00 04 lhz r11,4(r3) dd0: 7d 29 43 78 or r9,r9,r8 dd4: 7d 48 53 78 mr r8,r10 dd8: 88 a3 00 06 lbz r5,6(r3) ddc: 7d 29 43 78 or r9,r9,r8 de0: 7d 48 53 78 mr r8,r10 de4: 80 c3 00 08 lwz r6,8(r3) de8: 80 e3 00 0c lwz r7,12(r3) dec: 7d 29 43 78 or r9,r9,r8 df0: 7d 43 53 78 mr r3,r10 df4: 90 04 00 00 stw r0,0(r4) df8: 7d 29 1b 78 or r9,r9,r3 dfc: 7d 43 53 78 mr r3,r10 e00: b1 64 00 04 sth r11,4(r4) e04: 7d 29 1b 78 or r9,r9,r3 e08: 7d 43 53 78 mr r3,r10 e0c: 98 a4 00 06 stb r5,6(r4) e10: 7d 23 1b 78 or r3,r9,r3 e14: 90 c4 00 08 stw r6,8(r4) e18: 90 e4 00 0c stw r7,12(r4) e1c: 7c 63 53 78 or r3,r3,r10 e20: 4e 80 00 20 blr Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/c27bc4e598daf3bbb225de7a1f5c52121cf1e279.1597235091.git.christophe.leroy@csgroup.eu
-
Christophe Leroy authored
flush_instruction_cache() is never used on 8xx, remove it. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/245cabd8f291facac8c8c5fd370e361a69e02860.1597384145.git.christophe.leroy@csgroup.eu
-
Stephen Rothwell authored
Currently, using llvm-objtool, this script just silently succeeds without actually do the intended checking. So this updates it to work properly. Firstly, llvm-objdump does not add target symbol names to the end of branches in its asm output, so we have to drop the branch to __start_initialization_multiplatform using its address. Secondly, v9 and 10 specify branch targets as .+<offset>, so we convert those to actual addresses. Thirdly, v10 and 11 error out on a vmlinux if given the -R option complaining that it is "not a dynamic object". The -R does not make any difference to the asm output, so remove it. Lastly, v11 produces asm that is very similar to Gnu objtool (at least as far as branches are concerned), so no further changes are necessary to make it work. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200812081036.7969-3-sfr@canb.auug.org.au
-
Stephen Rothwell authored
This is considerably faster then parsing the objdump asm output. It will also make the enabling of llvm-objdump a little easier. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200812081036.7969-2-sfr@canb.auug.org.au
-
Stephen Rothwell authored
If we can't find the address of __end_interrupts, then we still exit successfully as that is the current behaviour. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200811140435.20957-8-sfr@canb.auug.org.au
-
Stephen Rothwell authored
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200811140435.20957-7-sfr@canb.auug.org.au
-
Stephen Rothwell authored
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200811140435.20957-6-sfr@canb.auug.org.au
-
Stephen Rothwell authored
Also start using sed -E and make all the separate expressions into a single one with comments. Pull the stripping of condition registers back into the sed command. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200811140435.20957-5-sfr@canb.auug.org.au
-
Stephen Rothwell authored
We don't use the raw hex instruction dump, so elide it and adjust the following expressions. Also use \s instead of [[:space:]] everywhere. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200811140435.20957-4-sfr@canb.auug.org.au
-
Stephen Rothwell authored
Also some minor style changes. There should still be no change in behaviour. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200811140435.20957-3-sfr@canb.auug.org.au
-
Stephen Rothwell authored
No functional change Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200811140435.20957-2-sfr@canb.auug.org.au
-
Scott Cheloha authored
At memory hot-remove time we can retrieve an LMB's nid from its corresponding memory_block. There is no need to store the nid in multiple locations. Note that lmb_to_memblock() uses find_memory_block() to get the corresponding memory_block. As find_memory_block() runs in sub-linear time this approach is negligibly slower than what we do at present. In exchange for this lookup at hot-remove time we no longer need to call memory_add_physaddr_to_nid() during drmem_init() for each LMB. On powerpc, memory_add_physaddr_to_nid() is a linear search, so this spares us an O(n^2) initialization during boot. On systems with many LMBs that initialization overhead is palpable and disruptive. For example, on a box with 249854 LMBs we're seeing drmem_init() take upwards of 30 seconds to complete: [ 53.721639] drmem: initializing drmem v2 [ 80.604346] watchdog: BUG: soft lockup - CPU#65 stuck for 23s! [swapper/0:1] [ 80.604377] Modules linked in: [ 80.604389] CPU: 65 PID: 1 Comm: swapper/0 Not tainted 5.6.0-rc2+ #4 [ 80.604397] NIP: c0000000000a4980 LR: c0000000000a4940 CTR: 0000000000000000 [ 80.604407] REGS: c0002dbff8493830 TRAP: 0901 Not tainted (5.6.0-rc2+) [ 80.604412] MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 44000248 XER: 0000000d [ 80.604431] CFAR: c0000000000a4a38 IRQMASK: 0 [ 80.604431] GPR00: c0000000000a4940 c0002dbff8493ac0 c000000001904400 c0003cfffffede30 [ 80.604431] GPR04: 0000000000000000 c000000000f4095a 000000000000002f 0000000010000000 [ 80.604431] GPR08: c0000bf7ecdb7fb8 c0000bf7ecc2d3c8 0000000000000008 c00c0002fdfb2001 [ 80.604431] GPR12: 0000000000000000 c00000001e8ec200 [ 80.604477] NIP [c0000000000a4980] hot_add_scn_to_nid+0xa0/0x3e0 [ 80.604486] LR [c0000000000a4940] hot_add_scn_to_nid+0x60/0x3e0 [ 80.604492] Call Trace: [ 80.604498] [c0002dbff8493ac0] [c0000000000a4940] hot_add_scn_to_nid+0x60/0x3e0 (unreliable) [ 80.604509] [c0002dbff8493b20] [c000000000087c10] memory_add_physaddr_to_nid+0x20/0x60 [ 80.604521] [c0002dbff8493b40] [c0000000010d4880] drmem_init+0x25c/0x2f0 [ 80.604530] [c0002dbff8493c10] [c000000000010154] do_one_initcall+0x64/0x2c0 [ 80.604540] [c0002dbff8493ce0] [c0000000010c4aa0] kernel_init_freeable+0x2d8/0x3a0 [ 80.604550] [c0002dbff8493db0] [c000000000010824] kernel_init+0x2c/0x148 [ 80.604560] [c0002dbff8493e20] [c00000000000b648] ret_from_kernel_thread+0x5c/0x74 [ 80.604567] Instruction dump: [ 80.604574] 392918e8 e9490000 e90a000a e92a0000 80ea000c 1d080018 3908ffe8 7d094214 [ 80.604586] 7fa94040 419d00dc e9490010 714a0088 <2faa0008> 409e00ac e9490000 7fbe5040 [ 89.047390] drmem: 249854 LMB(s) With a patched kernel on the same machine we're no longer seeing the soft lockup. drmem_init() now completes in negligible time, even when the LMB count is large. Fixes: b2d3b5ee ("powerpc/pseries: Track LMB nid instead of using device tree") Signed-off-by: Scott Cheloha <cheloha@linux.ibm.com> Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200811015115.63677-1-cheloha@linux.ibm.com
-
Christophe Leroy authored
Nothing prevents flush_cache_instruction() from being writen in C. Do it to improve readability and maintainability. This function is only use by low level callers, it is not intended to be used by module. Don't export it. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/f989eff8296800c427622c0985384148404e4f0b.1597384512.git.christophe.leroy@csgroup.eu
-
Christophe Leroy authored
Nothing prevents flush_cache_instruction() from being writen in C. Do it to improve readability and maintainability. This function is very small and isn't called from assembly, make it static inline in asm/cacheflush.h Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/93d93fc69b4b3ad3ceba2fc0756333c0c0245bb7.1597384512.git.christophe.leroy@csgroup.eu
-
Christophe Leroy authored
flush_instruction_cache() belongs to the cache flushing function family. Move its prototype in asm/cacheflush.h Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/993445b5227e8ca2f0e38bcc9ea3dfea6e865920.1597384512.git.christophe.leroy@csgroup.eu
-