Pull MMC updates from Ulf Hansson:
 "MMC core:

   - Add a new host cap bit and a corresponding DT property, to support
     power cycling of the card by FW at system suspend/resume.

   - Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode

   - Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
     cards

   - Convert the mmc-pwrseq DT bindings to the json-schema

   - Always allow the card detect uevent to be consumed by userspace

  MMC host controllers:

   - Convert a few DT bindings to the json-schema

   - mtk-sd:
      - Add support for command queue through cqhci
      - Add support for the MT6779 variant

   - renesas_sdhi_internal_dmac:
      - Fix dma unmapping in the error path

   - sdhci_am654:
      - Add support for the AM65x PG2.0 variant
      - Extend support for phys/clocks

   - sdhci-cadence:
      - Drop incorrect HW tuning for SD mode

   - sdhci-msm:
      - Add support for interconnect bandwidth scaling
      - Enable internal voltage control
      - Enable low power state for pinctrls

   - sdhci-of-at91:
      - Ludovic Desroches handovers maintenance to Eugen Hristev

   - sdhci-pci-gli:
      - Improve clock handling for GL975x

   - sdhci-pci-o2micro:
      - Add HW tuning for SDR104 mode
      - Fix support for O2 host controller Seabird1"

* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
  mmc: mediatek: make function msdc_cqe_disable() static
  MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
  dt-bindings: mmc: mediatek: Add document for mt6779
  mmc: mediatek: command queue support
  mmc: mediatek: refine msdc timeout api
  mmc: mediatek: add MT6779 MMC driver support
  mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
  mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
  mmc: via-sdmmc: use generic power management
  memstick: jmb38x_ms: use generic power management
  mmc: sdhci-cadence: do not use hardware tuning for SD mode
  mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
  mmc: cqhci: Fix a print format for the task descriptor
  mmc: sdhci-of-arasan: fix timings allocation code
  mmc: sdhci: Fix a potential uninitialized variable
  dt-bindings: mmc: renesas,sdhi: convert to YAML
  dt-bindings: mmc: convert arasan sdhci bindings to yaml
  mmc: sdhci: Fix potential null pointer access while accessing vqmmc
  mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
  dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
  ...

Pull hwmon updates from Guenter Roeck:
 "Highlights:
   - New driver for Sparx5 SoC temperature sensot
   - New driver for Corsair Commander Pro
   - MAX20710 support added to max20730 driver

  Enhancements:
   - max6697: Allow max6581 to create tempX_offset attributes
   - gsc (Gateworks System Controller): add 16bit pre-scaled voltage mode
   - adm1275: Enable adm1278 ADM1278_TEMP1_EN
   - dell-smm: Add Latitude 5480 to fan control whitelist

  Fixes:
   - adc128d818: Fix advanced configuration register init
   - pmbus/core: Use s64 instead of long for calculations to fix
     overflow issues with 32-bit architectures

  Plus various cleanups in several drivers"

* tag 'hwmon-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (32 commits)
  hwmon: (adc128d818) Fix advanced configuration register init
  hwmon: (axi-fan-control) remove duplicate macros
  hwmon: (i5k_amb, vt8231) Drop uses of pci_read_config_*() return value
  hwmon: (sparx5) Make symbol 's5_temp_match' static
  hwmon: (corsair-cpro) add reading pwm values
  hwmon: sparx5: Add Sparx5 SoC temperature driver
  dt-bindings: hwmon: Add Sparx5 temperature sensor
  hwmon: (tmp401) Replace HTTP links with HTTPS ones
  hwmon: (lm95234) Replace HTTP links with HTTPS ones
  hwmon: (lm90) Replace HTTP links with HTTPS ones
  hwmon: (k8temp) Replace HTTP links with HTTPS ones
  hwmon: (jc42) Replace HTTP links with HTTPS ones
  hwmon: (ina2xx) Replace HTTP links with HTTPS ones
  hwmon: (ina209) Replace HTTP links with HTTPS ones
  hwmon: Replace HTTP links with HTTPS ones
  docs: hwmon: Replace HTTP links with HTTPS ones
  hwmon: (adm1025) Replace HTTP links with HTTPS ones
  hwmon: add Corsair Commander Pro driver
  hwmon: (max6697) Allow max6581 to create tempX_offset
  hwmon: (tmmp513) Replace HTTP links with HTTPS links
  ...

Pull Devicetree updates from Rob Herring:

 - Improve device links cycle detection and breaking. Add more bindings
   for device link dependencies.

 - Refactor parsing 'no-map' in __reserved_mem_alloc_size()

 - Improve DT unittest 'ranges' and 'dma-ranges' test case to check
   differing cell sizes

 - Various http to https link conversions

 - Add a schema check to prevent 'syscon' from being used by itself
   without a more specific compatible

 - A bunch more DT binding conversions to schema

* tag 'devicetree-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
  of: reserved-memory: remove duplicated call to of_get_flat_dt_prop() for no-map node
  of: unittest: Use bigger address cells to catch parser regressions
  dt-bindings: memory-controllers: Convert mmdc to json-schema
  dt-bindings: mtd: Convert imx nand to json-schema
  dt-bindings: mtd: Convert gpmi nand to json-schema
  dt-bindings: iio: io-channel-mux: Fix compatible string in example code
  of: property: Add device link support for pinctrl-0 through pinctrl-8
  of: property: Add device link support for multiple DT bindings
  dt-bindings: phy: ti: phy-gmii-sel: convert bindings to json-schema
  dt-bindings: mux: mux.h: drop a duplicated word
  dt-bindings: misc: Convert olpc,xo1.75-ec to json-schema
  dt-bindings: aspeed-lpc: Replace HTTP links with HTTPS ones
  dt-bindings: drm/bridge: Replace HTTP links with HTTPS ones
  drm/tilcdc: Replace HTTP links with HTTPS ones
  dt-bindings: iommu: renesas,ipmmu-vmsa: Add r8a774e1 support
  dt-bindings: fpga: Replace HTTP links with HTTPS ones
  dt-bindings: virtio: Replace HTTP links with HTTPS ones
  dt-bindings: media: imx274: Add optional input clock and supplies
  dt-bindings: i2c-gpio: Use 'deprecated' keyword on deprecated properties
  dt-bindings: interrupt-controller: Fix typos in loongson,liointc.yaml
  ...

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v5.9 kernel cycle.

  There is nothing too exciting in it, but a new macro that fixes a
  build failure on a minor ARM32 platform that appeared yesterday is
  part of it so we better merge it.

  Core changes:

   - Introduce the for_each_requested_gpio() macro to help in dependent
     code all over the place. Also patch a few locations to use it while
     we are at it.

   - Split out the sysfs code into its own file.

   - Split out the character device code into its own file, then make a
     set of refactorings and improvements to this code. We are setting
     the stage to revamp the userspace API a bit in the next cycle.

   - Fix a whole slew of kerneldoc that was wrong or missing.

  New drivers:

   - The PCA953x driver now supports the PCAL9535.

  Driver improvements:

   - A host of incremental modernizations and improvements to the
     PCA953x driver.

   - Incremental improvements to the Xilinx Zynq driver.

   - Some improvements to the GPIO aggregator driver.

   - I ran all over the place switching all threaded and other drivers
     requesting their own IRQ while using the core GPIO IRQ helpers to
     pass the GPIO irq chip as a template instead of calling the
     explicit set-up functions. Next merge window we may retire the old
     code altogether"

* tag 'gpio-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (97 commits)
  gpio: wcove: Request IRQ after all initialisation done
  gpio: crystalcove: Free IRQ on error path
  gpio: pca953x: Request IRQ after all initialisation done
  gpio: don't use same lockdep class for all devm_gpiochip_add_data users
  gpio: max732x: Use irqchip template
  gpio: stmpe: Move chip registration
  gpio: rcar: Use irqchip template
  gpio: regmap: fix type clash
  gpio: Correct kernel-doc inconsistency
  gpio: pci-idio-16: Use irqchip template
  gpio: pcie-idio-24: Use irqchip template
  gpio: 104-idio-16: Use irqchip template
  gpio: 104-idi-48: Use irqchip template
  gpio: 104-dio-48e: Use irqchip template
  gpio: ws16c48: Use irqchip template
  gpio: omap: improve coding style for pin config flags
  gpio: dln2: Use irqchip template
  gpio: sch: Add a blank line between declaration and code
  gpio: sch: changed every 'unsigned' to 'unsigned int'
  gpio: ich: changed every 'unsigned' to 'unsigned int'
  ...

This is hopefully the final piece of the crazy puzzle with random.h
dependencies.

And by "hopefully" I obviously mean "Linus is a hopeless optimist".
Reported-and-tested-by: Daniel Díaz <daniel.diaz@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull USB/Thunderbolt updates from Greg KH:
 "Here is the large set of USB and Thunderbolt patches for 5.9-rc1.

  Nothing really magic/major in here, just lots of little changes and
  updates:

   - clean up language usages in USB core and some drivers

   - Thunderbolt driver updates and additions

   - USB Gadget driver updates

   - dwc3 driver updates (like always...)

   - build with "W=1" warning fixups

   - mtu3 driver updates

   - usb-serial driver updates and device ids

   - typec additions and updates for new hardware

   - xhci debug code updates for future platforms

   - cdns3 driver updates

   - lots of other minor driver updates and fixes and cleanups

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (330 commits)
  usb: common: usb-conn-gpio: Register charger
  usb: mtu3: simplify mtu3_req_complete()
  usb: mtu3: clear dual mode of u3port when disable device
  usb: mtu3: use MTU3_EP_WEDGE flag
  usb: mtu3: remove useless member @busy in mtu3_ep struct
  usb: mtu3: remove repeated error log
  usb: mtu3: add ->udc_set_speed()
  usb: mtu3: introduce a funtion to check maximum speed
  usb: mtu3: clear interrupts status when disable interrupts
  usb: mtu3: reinitialize CSR registers
  usb: mtu3: fix macro for maximum number of packets
  usb: mtu3: remove unnecessary pointer checks
  usb: xhci: Fix ASMedia ASM1142 DMA addressing
  usb: xhci: define IDs for various ASMedia host controllers
  usb: musb: convert to devm_platform_ioremap_resource_byname
  usb: gadget: tegra-xudc: convert to devm_platform_ioremap_resource_byname
  usb: gadget: r8a66597: convert to devm_platform_ioremap_resource_byname
  usb: dwc3: convert to devm_platform_ioremap_resource_byname
  usb: cdns3: convert to devm_platform_ioremap_resource_byname
  usb: phy: am335x: convert to devm_platform_ioremap_resource_byname
  ...

Pull driver core updates from Greg KH:
 "Here is the "big" set of changes to the driver core, and some drivers
  using the changes, for 5.9-rc1.

  "Biggest" thing in here is the device link exposure in sysfs, to help
  to tame the madness that is SoC device tree representations and driver
  interactions with it.

  Other stuff in here that is interesting is:

   - device probe log helper so that drivers can report problems in a
     unified way easier.

   - devres functions added

   - DEVICE_ATTR_ADMIN_* macro added to make it harder to write
     incorrect sysfs file permissions

   - documentation cleanups

   - ability for debugfs to be present in the kernel, yet not exposed to
     userspace. Needed for systems that want it enabled, but do not
     trust users, so they can still use some kernel functions that were
     otherwise disabled.

   - other minor fixes and cleanups

  The patches outside of drivers/base/ all have acks from the respective
  subsystem maintainers to go through this tree instead of theirs.

  All of these have been in linux-next with no reported issues"

* tag 'driver-core-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (39 commits)
  drm/bridge: lvds-codec: simplify error handling
  drm/bridge/sii8620: fix resource acquisition error handling
  driver core: add deferring probe reason to devices_deferred property
  driver core: add device probe log helper
  driver core: Avoid binding drivers to dead devices
  Revert "test_firmware: Test platform fw loading on non-EFI systems"
  firmware_loader: EFI firmware loader must handle pre-allocated buffer
  selftest/firmware: Add selftest timeout in settings
  test_firmware: Test platform fw loading on non-EFI systems
  driver core: Change delimiter in devlink device's name to "--"
  debugfs: Add access restriction option
  tracefs: Remove unnecessary debug_fs checks.
  driver core: Fix probe_count imbalance in really_probe()
  kobject: remove unused KOBJ_MAX action
  driver core: Fix sleeping in invalid context during device link deletion
  driver core: Add waiting_for_supplier sysfs file for devices
  driver core: Add state_synced sysfs file for devices that support it
  driver core: Expose device link details in sysfs
  driver core: Drop mention of obsolete bus rwsem from kernel-doc
  debugfs: file: Remove unnecessary cast in kfree()
  ...

Pull char/misc driver updates from Greg KH:
 "Here is the large set of char and misc and other driver subsystem
  patches for 5.9-rc1. Lots of new driver submissions in here, and
  cleanups and features for existing drivers.

  Highlights are:
   - habanalabs driver updates
   - coresight driver updates
   - nvmem driver updates
   - huge number of "W=1" build warning cleanups from Lee Jones
   - dyndbg updates
   - virtbox driver fixes and updates
   - soundwire driver updates
   - mei driver updates
   - phy driver updates
   - fpga driver updates
   - lots of smaller individual misc/char driver cleanups and fixes

  Full details are in the shortlog.

  All of these have been in linux-next with no reported issues"

* tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (322 commits)
  habanalabs: remove unused but set variable 'ctx_asid'
  nvmem: qcom-spmi-sdam: Enable multiple devices
  dt-bindings: nvmem: SID: add binding for A100's SID controller
  nvmem: update Kconfig description
  nvmem: qfprom: Add fuse blowing support
  dt-bindings: nvmem: Add properties needed for blowing fuses
  dt-bindings: nvmem: qfprom: Convert to yaml
  nvmem: qfprom: use NVMEM_DEVID_AUTO for multiple instances
  nvmem: core: add support to auto devid
  nvmem: core: Add nvmem_cell_read_u8()
  nvmem: core: Grammar fixes for help text
  nvmem: sc27xx: add sc2730 efuse support
  nvmem: Enforce nvmem stride in the sysfs interface
  MAINTAINERS: Add git tree for NVMEM FRAMEWORK
  nvmem: sprd: Fix return value of sprd_efuse_probe()
  drivers: android: Fix the SPDX comment style
  drivers: android: Fix a variable declaration coding style issue
  drivers: android: Remove braces for a single statement if-else block
  drivers: android: Remove the use of else after return
  drivers: android: Fix a variable declaration coding style issue
  ...

Pull block stacking updates from Jens Axboe:
 "The stacking related fixes depended on both the core block and drivers
  branches, so here's a topic branch with that change.

  Outside of that, a late fix from Johannes for zone revalidation"

* tag 'for-5.9/block-merge-20200804' of git://git.kernel.dk/linux-block:
  block: don't do revalidate zones on invalid devices
  block: remove blk_queue_stack_limits
  block: remove bdev_stack_limits
  block: inherit the zoned characteristics in blk_stack_limits

syzbot has revealed that the "phylink" keyword exists in non-phylink
related contexts in the bluetooth stack. To avoid receiving
inappropriate notifications, change the keyword matching regexp to
something which avoids this, while still allowing changes to networking
drivers that make use of phylink to be detected.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull block driver updates from Jens Axboe:

 - NVMe:
      - ZNS support (Aravind, Keith, Matias, Niklas)
      - Misc cleanups, optimizations, fixes (Baolin, Chaitanya, David,
        Dongli, Max, Sagi)

 - null_blk zone capacity support (Aravind)

 - MD:
      - raid5/6 fixes (ChangSyun)
      - Warning fixes (Damien)
      - raid5 stripe fixes (Guoqing, Song, Yufen)
      - sysfs deadlock fix (Junxiao)
      - raid10 deadlock fix (Vitaly)

 - struct_size conversions (Gustavo)

 - Set of bcache updates/fixes (Coly)

* tag 'for-5.9/drivers-20200803' of git://git.kernel.dk/linux-block: (117 commits)
  md/raid5: Allow degraded raid6 to do rmw
  md/raid5: Fix Force reconstruct-write io stuck in degraded raid5
  raid5: don't duplicate code for different paths in handle_stripe
  raid5-cache: hold spinlock instead of mutex in r5c_journal_mode_show
  md: print errno in super_written
  md/raid5: remove the redundant setting of STRIPE_HANDLE
  md: register new md sysfs file 'uuid' read-only
  md: fix max sectors calculation for super 1.0
  nvme-loop: remove extra variable in create ctrl
  nvme-loop: set ctrl state connecting after init
  nvme-multipath: do not fall back to __nvme_find_path() for non-optimized paths
  nvme-multipath: fix logic for non-optimized paths
  nvme-rdma: fix controller reset hang during traffic
  nvme-tcp: fix controller reset hang during traffic
  nvmet: introduce the passthru Kconfig option
  nvmet: introduce the passthru configfs interface
  nvmet: Add passthru enable/disable helpers
  nvmet: add passthru code to process commands
  nvme: export nvme_find_get_ns() and nvme_put_ns()
  nvme: introduce nvme_ctrl_get_by_path()
  ...

Merge tag 'linux-kselftest-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest updates form Shuah Khan:

 - TAP output reporting related fixes from Paolo Bonzini and Kees Cook.

   These fixes make it skip reporting consistent with TAP format.

 - Cleanup fixes to framework run_tests from Yauheni Kaliuta

* tag 'linux-kselftest-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (23 commits)
  selftests/harness: Limit step counter reporting
  selftests/seccomp: Check ENOSYS under tracing
  selftests/seccomp: Refactor to use fixture variants
  selftests/harness: Clean up kern-doc for fixtures
  selftests: kmod: Add module address visibility test
  Replace HTTP links with HTTPS ones: KMOD KERNEL MODULE LOADER - USERMODE HELPER
  selftests: fix condition in run_tests
  selftests: do not use .ONESHELL
  selftests: pidfd: skip test if unshare fails with EPERM
  selftests: pidfd: do not use ksft_exit_skip after ksft_set_plan
  selftests/harness: Report skip reason
  selftests/harness: Display signed values correctly
  selftests/harness: Refactor XFAIL into SKIP
  selftests/harness: Switch to TAP output
  selftests: Add header documentation and helpers
  selftests/binderfs: Fix harness API usage
  selftests: Remove unneeded selftest API headers
  selftests/clone3: Reorder reporting output
  selftests: sync_test: do not use ksft_exit_skip after ksft_set_plan
  selftests: sigaltstack: do not use ksft_exit_skip after ksft_set_plan
  ...

Merge tag 'linux-kselftest-kunit-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kunit updates from Shuah Khan:

 - Add a generic kunit_resource API extending it to support resources
   that are passed in to kunit in addition kunit allocated resources. In
   addition, KUnit resources are now refcounted to avoid passed in
   resources being released while in use by kunit.

 - Add support for named resources.

 - Important bug fixes from Brendan Higgins and Will Chen

* tag 'linux-kselftest-kunit-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  kunit: tool: fix improper treatment of file location
  kunit: tool: fix broken default args in unit tests
  kunit: capture stderr on all make subprocess calls
  Documentation: kunit: Remove references to --defconfig
  kunit: add support for named resources
  kunit: generalize kunit_resource API beyond allocated resources

The sparse tool complains as follows:

drivers/mmc/host/mtk-sd.c:2269:6: warning:
 symbol 'msdc_cqe_disable' was not declared. Should it be static?

This function is not used outside of mtk-sd.c, so this commit
marks it static.

Fixes: 88bd652b ("mmc: mediatek: command queue support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Link: https://lore.kernel.org/r/20200727171129.2945-1-weiyongjun1@huawei.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As Eugen handles the software for bootloaders and new products, handover
the maintenance to him.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20200709085331.8145-1-ludovic.desroches@microchip.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull documentation updates from Jonathan Corbet:
 "It's been a busy cycle for documentation - hopefully the busiest for a
  while to come. Changes include:

   - Some new Chinese translations

   - Progress on the battle against double words words and non-HTTPS
     URLs

   - Some block-mq documentation

   - More RST conversions from Mauro. At this point, that task is
     essentially complete, so we shouldn't see this kind of churn again
     for a while. Unless we decide to switch to asciidoc or
     something...:)

   - Lots of typo fixes, warning fixes, and more"

* tag 'docs-5.9' of git://git.lwn.net/linux: (195 commits)
  scripts/kernel-doc: optionally treat warnings as errors
  docs: ia64: correct typo
  mailmap: add entry for <alobakin@marvell.com>
  doc/zh_CN: add cpu-load Chinese version
  Documentation/admin-guide: tainted-kernels: fix spelling mistake
  MAINTAINERS: adjust kprobes.rst entry to new location
  devices.txt: document rfkill allocation
  PCI: correct flag name
  docs: filesystems: vfs: correct flag name
  docs: filesystems: vfs: correct sync_mode flag names
  docs: path-lookup: markup fixes for emphasis
  docs: path-lookup: more markup fixes
  docs: path-lookup: fix HTML entity mojibake
  CREDITS: Replace HTTP links with HTTPS ones
  docs: process: Add an example for creating a fixes tag
  doc/zh_CN: add Chinese translation prefer section
  doc/zh_CN: add clearing-warn-once Chinese version
  doc/zh_CN: add admin-guide index
  doc:it_IT: process: coding-style.rst: Correct __maybe_unused compiler label
  futex: MAINTAINERS: Re-add selftests directory
  ...

Pull printk updates from Petr Mladek:

 - Herbert Xu made printk header file self-contained.

 - Andy Shevchenko and Sergey Senozhatsky cleaned up console->setup()
   error handling.

 - Andy Shevchenko did some cleanups (e.g. sparse warning) in vsprintf
   code.

 - Minor documentation updates.

* tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
  lib/vsprintf: Force type of flags value for gfp_t
  lib/vsprintf: Replace custom spec to print decimals with generic one
  lib/vsprintf: Replace hidden BUILD_BUG_ON() with static_assert()
  printk: Make linux/printk.h self-contained
  doc:kmsg: explicitly state the return value in case of SEEK_CUR
  Replace HTTP links with HTTPS ones: vsprintf
  hvc: unify console setup naming
  console: Fix trivia typo 'change' -> 'chance'
  console: Propagate error code from console ->setup()
  tty: hvc: Return proper error code from console ->setup() hook
  serial: sunzilog: Return proper error code from console ->setup() hook
  serial: sunsab: Return proper error code from console ->setup() hook
  mips: Return proper error code from console ->setup() hook

Pull parisc updates from Helge Deller:
 "The majority of the patches are reverts of previous commits regarding
  the parisc-specific low level spinlocking code and barrier handling,
  with which we tried to fix CPU stalls on our build servers. In the end
  John David Anglin found the culprit: We missed a define for
  atomic64_set_release(). This seems to have fixed our issues, so now
  it's good to remove the unnecessary code again.

  Other than that it's trivial stuff: Spelling fixes, constifications
  and such"

* 'parisc-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: make the log level string for register dumps const
  parisc: Do not use an ordered store in pa_tlb_lock()
  Revert "parisc: Revert "Release spinlocks using ordered store""
  Revert "parisc: Use ldcw instruction for SMP spinlock release barrier"
  Revert "parisc: Drop LDCW barrier in CAS code when running UP"
  Revert "parisc: Improve interrupt handling in arch_spin_lock_flags()"
  parisc: Replace HTTP links with HTTPS ones
  parisc: elf.h: delete a duplicated word
  parisc: Report bad pages as HardwareCorrupted
  parisc: Convert to BIT_MASK() and BIT_WORD()

Pull x86 fsgsbase from Thomas Gleixner:
 "Support for FSGSBASE. Almost 5 years after the first RFC to support
  it, this has been brought into a shape which is maintainable and
  actually works.

  This final version was done by Sasha Levin who took it up after Intel
  dropped the ball. Sasha discovered that the SGX (sic!) offerings out
  there ship rogue kernel modules enabling FSGSBASE behind the kernels
  back which opens an instantanious unpriviledged root hole.

  The FSGSBASE instructions provide a considerable speedup of the
  context switch path and enable user space to write GSBASE without
  kernel interaction. This enablement requires careful handling of the
  exception entries which go through the paranoid entry path as they
  can no longer rely on the assumption that user GSBASE is positive (as
  enforced via prctl() on non FSGSBASE enabled systemn).

  All other entries (syscalls, interrupts and exceptions) can still just
  utilize SWAPGS unconditionally when the entry comes from user space.
  Converting these entries to use FSGSBASE has no benefit as SWAPGS is
  only marginally slower than WRGSBASE and locating and retrieving the
  kernel GSBASE value is not a free operation either. The real benefit
  of RD/WRGSBASE is the avoidance of the MSR reads and writes.

  The changes come with appropriate selftests and have held up in field
  testing against the (sanitized) Graphene-SGX driver"

* tag 'x86-fsgsbase-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
  x86/fsgsbase: Fix Xen PV support
  x86/ptrace: Fix 32-bit PTRACE_SETREGS vs fsbase and gsbase
  selftests/x86/fsgsbase: Add a missing memory constraint
  selftests/x86/fsgsbase: Fix a comment in the ptrace_write_gsbase test
  selftests/x86: Add a syscall_arg_fault_64 test for negative GSBASE
  selftests/x86/fsgsbase: Test ptracer-induced GS base write with FSGSBASE
  selftests/x86/fsgsbase: Test GS selector on ptracer-induced GS base write
  Documentation/x86/64: Add documentation for GS/FS addressing mode
  x86/elf: Enumerate kernel FSGSBASE capability in AT_HWCAP2
  x86/cpu: Enable FSGSBASE on 64bit by default and add a chicken bit
  x86/entry/64: Handle FSGSBASE enabled paranoid entry/exit
  x86/entry/64: Introduce the FIND_PERCPU_BASE macro
  x86/entry/64: Switch CR3 before SWAPGS in paranoid entry
  x86/speculation/swapgs: Check FSGSBASE in enabling SWAPGS mitigation
  x86/process/64: Use FSGSBASE instructions on thread copy and ptrace
  x86/process/64: Use FSBSBASE in switch_to() if available
  x86/process/64: Make save_fsgs_for_kvm() ready for FSGSBASE
  x86/fsgsbase/64: Enable FSGSBASE instructions in helper functions
  x86/fsgsbase/64: Add intrinsics for FSGSBASE instructions
  x86/cpu: Add 'unsafe_fsgsbase' to enable CR4.FSGSBASE
  ...

Pull x86 conversion to generic entry code from Thomas Gleixner:
 "The conversion of X86 syscall, interrupt and exception entry/exit
  handling to the generic code.

  Pretty much a straight-forward 1:1 conversion plus the consolidation
  of the KVM handling of pending work before entering guest mode"

* tag 'x86-entry-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kvm: Use __xfer_to_guest_mode_work_pending() in kvm_run_vcpu()
  x86/kvm: Use generic xfer to guest work function
  x86/entry: Cleanup idtentry_enter/exit
  x86/entry: Use generic interrupt entry/exit code
  x86/entry: Cleanup idtentry_entry/exit_user
  x86/entry: Use generic syscall exit functionality
  x86/entry: Use generic syscall entry function
  x86/ptrace: Provide pt_regs helper for entry/exit
  x86/entry: Move user return notifier out of loop
  x86/entry: Consolidate 32/64 bit syscall entry
  x86/entry: Consolidate check_user_regs()
  x86: Correct noinstr qualifiers
  x86/idtentry: Remove stale comment

Pull generic kernel entry/exit code from Thomas Gleixner:
 "Generic implementation of common syscall, interrupt and exception
  entry/exit functionality based on the recent X86 effort to ensure
  correctness of entry/exit vs RCU and instrumentation.

  As this functionality and the required entry/exit sequences are not
  architecture specific, sharing them allows other architectures to
  benefit instead of copying the same code over and over again.

  This branch was kept standalone to allow others to work on it. The
  conversion of x86 comes in a seperate pull request which obviously is
  based on this branch"

* tag 'core-entry-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  entry: Correct __secure_computing() stub
  entry: Correct 'noinstr' attributes
  entry: Provide infrastructure for work before transitioning to guest mode
  entry: Provide generic interrupt entry/exit code
  entry: Provide generic syscall exit function
  entry: Provide generic syscall entry functionality
  seccomp: Provide stub for __secure_computing()

Pull timer updates from Thomas Gleixner:
 "Time, timers and related driver updates:

   - Prevent unnecessary timer softirq invocations by extending the
     tracking of the next expiring timer in the timer wheel beyond the
     existing NOHZ functionality.

     The tracking overhead at enqueue time is within the noise, but on
     sensitive workloads the avoidance of the soft interrupt invocation
     is a measurable improvement.

   - The obligatory new clocksource driver for Ingenic X100 OST

   - The usual fixes, improvements, cleanups and extensions for newer
     chip variants all over the driver space"

* tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
  timers: Recalculate next timer interrupt only when necessary
  clocksource/drivers/ingenic: Add support for the Ingenic X1000 OST.
  dt-bindings: timer: Add Ingenic X1000 OST bindings.
  clocksource/drivers: Replace HTTP links with HTTPS ones
  clocksource/drivers/nomadik-mtu: Handle 32kHz clock
  clocksource/drivers/sh_cmt: Use "kHz" for kilohertz
  clocksource/drivers/imx: Add support for i.MX TPM driver with ARM64
  clocksource/drivers/ingenic: Add high resolution timer support for SMP/SMT.
  timers: Lower base clock forwarding threshold
  timers: Remove must_forward_clk
  timers: Spare timer softirq until next expiry
  timers: Expand clk forward logic beyond nohz
  timers: Reuse next expiry cache after nohz exit
  timers: Always keep track of next expiry
  timers: Optimize _next_timer_interrupt() level iteration
  timers: Add comments about calc_index() ceiling work
  timers: Move trigger_dyntick_cpu() to enqueue_timer()
  timers: Use only bucket expiry for base->next_expiry value
  timers: Preserve higher bits of expiration on index calculation
  clocksource/drivers/timer-atmel-tcb: Add sama5d2 support
  ...

Pull irq updates from Thomas Gleixner:
 "The usual boring updates from the interrupt subsystem:

   - Infrastructure to allow building irqchip drivers as modules

   - Consolidation of irqchip ACPI probing

   - Removal of the EOI-preflow interrupt handler which was required for
     SPARC support and became obsolete after SPARC was converted to use
     sparse interrupts.

   - Cleanups, fixes and improvements all over the place"

* tag 'irq-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
  irqchip/loongson-pch-pic: Fix the misused irq flow handler
  irqchip/loongson-htvec: Support 8 groups of HT vectors
  irqchip/loongson-liointc: Fix misuse of gc->mask_cache
  dt-bindings: interrupt-controller: Update Loongson HTVEC description
  irqchip/imx-intmux: Fix irqdata regs save in imx_intmux_runtime_suspend()
  irqchip/imx-intmux: Implement intmux runtime power management
  irqchip/gic-v4.1: Use GFP_ATOMIC flag in allocate_vpe_l1_table()
  irqchip: Fix IRQCHIP_PLATFORM_DRIVER_* compilation by including module.h
  irqchip/stm32-exti: Map direct event to irq parent
  irqchip/mtk-cirq: Convert to a platform driver
  irqchip/mtk-sysirq: Convert to a platform driver
  irqchip/qcom-pdc: Switch to using IRQCHIP_PLATFORM_DRIVER helper macros
  irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros
  irqchip: irq-bcm2836.h: drop a duplicated word
  irqchip/gic-v4.1: Ensure accessing the correct RD when writing INVALLR
  irqchip/irq-bcm7038-l1: Guard uses of cpu_logical_map
  irqchip/gic-v3: Remove unused register definition
  irqchip/qcom-pdc: Allow QCOM_PDC to be loadable as a permanent module
  genirq: Export irq_chip_retrigger_hierarchy and irq_chip_set_vcpu_affinity_parent
  irqdomain: Export irq_domain_update_bus_token
  ...

Pull dma-mapping updates from Christoph Hellwig:

 - make support for dma_ops optional

 - move more code out of line

 - add generic support for a dma_ops bypass mode

 - misc cleanups

* tag 'dma-mapping-5.9' of git://git.infradead.org/users/hch/dma-mapping:
  dma-contiguous: cleanup dma_alloc_contiguous
  dma-debug: use named initializers for dir2name
  powerpc: use the generic dma_ops_bypass mode
  dma-mapping: add a dma_ops_bypass flag to struct device
  dma-mapping: make support for dma ops optional
  dma-mapping: inline the fast path dma-direct calls
  dma-mapping: move the remaining DMA API calls out of line

Pull uuid update from Christoph Hellwig:
 "Remove a now unused helper (Andy Shevchenko)"

* tag 'uuid-for-5.9' of git://git.infradead.org/users/hch/uuid:
  uuid: remove unused uuid_le_to_bin() definition

Pull close_range() implementation from Christian Brauner:
 "This adds the close_range() syscall. It allows to efficiently close a
  range of file descriptors up to all file descriptors of a calling
  task.

  This is coordinated with the FreeBSD folks which have copied our
  version of this syscall and in the meantime have already merged it in
  April 2019:

    https://reviews.freebsd.org/D21627
    https://svnweb.freebsd.org/base?view=revision&revision=359836

  The syscall originally came up in a discussion around the new mount
  API and making new file descriptor types cloexec by default. During
  this discussion, Al suggested the close_range() syscall.

  First, it helps to close all file descriptors of an exec()ing task.
  This can be done safely via (quoting Al's example from [1] verbatim):

        /* that exec is sensitive */
        unshare(CLONE_FILES);
        /* we don't want anything past stderr here */
        close_range(3, ~0U);
        execve(....);

  The code snippet above is one way of working around the problem that
  file descriptors are not cloexec by default. This is aggravated by the
  fact that we can't just switch them over without massively regressing
  userspace. For a whole class of programs having an in-kernel method of
  closing all file descriptors is very helpful (e.g. demons, service
  managers, programming language standard libraries, container managers
  etc.).

  Second, it allows userspace to avoid implementing closing all file
  descriptors by parsing through /proc/<pid>/fd/* and calling close() on
  each file descriptor and other hacks. From looking at various
  large(ish) userspace code bases this or similar patterns are very
  common in service managers, container runtimes, and programming
  language runtimes/standard libraries such as Python or Rust.

  In addition, the syscall will also work for tasks that do not have
  procfs mounted and on kernels that do not have procfs support compiled
  in. In such situations the only way to make sure that all file
  descriptors are closed is to call close() on each file descriptor up
  to UINT_MAX or RLIMIT_NOFILE, OPEN_MAX trickery.

  Based on Linus' suggestion close_range() also comes with a new flag
  CLOSE_RANGE_UNSHARE to more elegantly handle file descriptor dropping
  right before exec. This would usually be expressed in the sequence:

        unshare(CLONE_FILES);
        close_range(3, ~0U);

  as pointed out by Linus it might be desirable to have this be a part
  of close_range() itself under a new flag CLOSE_RANGE_UNSHARE which
  gets especially handy when we're closing all file descriptors above a
  certain threshold.

  Test-suite as always included"

* tag 'close-range-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  tests: add CLOSE_RANGE_UNSHARE tests
  close_range: add CLOSE_RANGE_UNSHARE
  tests: add close_range() tests
  arch: wire-up close_range()
  open: add close_range()

Merge tag 'cap-checkpoint-restore-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux

Pull checkpoint-restore updates from Christian Brauner:
 "This enables unprivileged checkpoint/restore of processes.

  Given that this work has been going on for quite some time the first
  sentence in this summary is hopefully more exciting than the actual
  final code changes required. Unprivileged checkpoint/restore has seen
  a frequent increase in interest over the last two years and has thus
  been one of the main topics for the combined containers &
  checkpoint/restore microconference since at least 2018 (cf. [1]).

  Here are just the three most frequent use-cases that were brought forward:

   - The JVM developers are integrating checkpoint/restore into a Java
     VM to significantly decrease the startup time.

   - In high-performance computing environment a resource manager will
     typically be distributing jobs where users are always running as
     non-root. Long-running and "large" processes with significant
     startup times are supposed to be checkpointed and restored with
     CRIU.

   - Container migration as a non-root user.

  In all of these scenarios it is either desirable or required to run
  without CAP_SYS_ADMIN. The userspace implementation of
  checkpoint/restore CRIU already has the pull request for supporting
  unprivileged checkpoint/restore up (cf. [2]).

  To enable unprivileged checkpoint/restore a new dedicated capability
  CAP_CHECKPOINT_RESTORE is introduced. This solution has last been
  discussed in 2019 in a talk by Google at Linux Plumbers (cf. [1]
  "Update on Task Migration at Google Using CRIU") with Adrian and
  Nicolas providing the implementation now over the last months. In
  essence, this allows the CRIU binary to be installed with the
  CAP_CHECKPOINT_RESTORE vfs capability set thereby enabling
  unprivileged users to restore processes.

  To make this possible the following permissions are altered:

   - Selecting a specific PID via clone3() set_tid relaxed from userns
     CAP_SYS_ADMIN to CAP_CHECKPOINT_RESTORE.

   - Selecting a specific PID via /proc/sys/kernel/ns_last_pid relaxed
     from userns CAP_SYS_ADMIN to CAP_CHECKPOINT_RESTORE.

   - Accessing /proc/pid/map_files relaxed from init userns
     CAP_SYS_ADMIN to init userns CAP_CHECKPOINT_RESTORE.

   - Changing /proc/self/exe from userns CAP_SYS_ADMIN to userns
     CAP_CHECKPOINT_RESTORE.

  Of these four changes the /proc/self/exe change deserves a few words
  because the reasoning behind even restricting /proc/self/exe changes
  in the first place is just full of historical quirks and tracking this
  down was a questionable version of fun that I'd like to spare others.

  In short, it is trivial to change /proc/self/exe as an unprivileged
  user, i.e. without userns CAP_SYS_ADMIN right now. Either via ptrace()
  or by simply intercepting the elf loader in userspace during exec.
  Nicolas was nice enough to even provide a POC for the latter (cf. [3])
  to illustrate this fact.

  The original patchset which introduced PR_SET_MM_MAP had no
  permissions around changing the exe link. They too argued that it is
  trivial to spoof the exe link already which is true. The argument
  brought up against this was that the Tomoyo LSM uses the exe link in
  tomoyo_manager() to detect whether the calling process is a policy
  manager. This caused changing the exe links to be guarded by userns
  CAP_SYS_ADMIN.

  All in all this rather seems like a "better guard it with something
  rather than nothing" argument which imho doesn't qualify as a great
  security policy. Again, because spoofing the exe link is possible for
  the calling process so even if this were security relevant it was
  broken back then and would be broken today. So technically, dropping
  all permissions around changing the exe link would probably be
  possible and would send a clearer message to any userspace that relies
  on /proc/self/exe for security reasons that they should stop doing
  this but for now we're only relaxing the exe link permissions from
  userns CAP_SYS_ADMIN to userns CAP_CHECKPOINT_RESTORE.

  There's a final uapi change in here. Changing the exe link used to
  accidently return EINVAL when the caller lacked the necessary
  permissions instead of the more correct EPERM. This pr contains a
  commit fixing this. I assume that userspace won't notice or care and
  if they do I will revert this commit. But since we are changing the
  permissions anyway it seems like a good opportunity to try this fix.

  With these changes merged unprivileged checkpoint/restore will be
  possible and has already been tested by various users"

[1] LPC 2018
     1. "Task Migration at Google Using CRIU"
        https://www.youtube.com/watch?v=yI_1cuhoDgA&t=12095
     2. "Securely Migrating Untrusted Workloads with CRIU"
        https://www.youtube.com/watch?v=yI_1cuhoDgA&t=14400
     LPC 2019
     1. "CRIU and the PID dance"
         https://www.youtube.com/watch?v=LN2CUgp8deo&list=PLVsQ_xZBEyN30ZA3Pc9MZMFzdjwyz26dO&index=9&t=2m48s
     2. "Update on Task Migration at Google Using CRIU"
        https://www.youtube.com/watch?v=LN2CUgp8deo&list=PLVsQ_xZBEyN30ZA3Pc9MZMFzdjwyz26dO&index=9&t=1h2m8s

[2] https://github.com/checkpoint-restore/criu/pull/1155

[3] https://github.com/nviennot/run_as_exe

* tag 'cap-checkpoint-restore-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  selftests: add clone3() CAP_CHECKPOINT_RESTORE test
  prctl: exe link permission error changed from -EINVAL to -EPERM
  prctl: Allow local CAP_CHECKPOINT_RESTORE to change /proc/self/exe
  proc: allow access in init userns for map_files with CAP_CHECKPOINT_RESTORE
  pid_namespace: use checkpoint_restore_ns_capable() for ns_last_pid
  pid: use checkpoint_restore_ns_capable() for set_tid
  capabilities: Introduce CAP_CHECKPOINT_RESTORE

Pull fork cleanups from Christian Brauner:
 "This is cleanup series from when we reworked a chunk of the process
  creation paths in the kernel and switched to struct
  {kernel_}clone_args.

  High-level this does two main things:

   - Remove the double export of both do_fork() and _do_fork() where
     do_fork() used the incosistent legacy clone calling convention.

     Now we only export _do_fork() which is based on struct
     kernel_clone_args.

   - Remove the copy_thread_tls()/copy_thread() split making the
     architecture specific HAVE_COYP_THREAD_TLS config option obsolete.

  This switches all remaining architectures to select
  HAVE_COPY_THREAD_TLS and thus to the copy_thread_tls() calling
  convention. The current split makes the process creation codepaths
  more convoluted than they need to be. Each architecture has their own
  copy_thread() function unless it selects HAVE_COPY_THREAD_TLS then it
  has a copy_thread_tls() function.

  The split is not needed anymore nowadays, all architectures support
  CLONE_SETTLS but quite a few of them never bothered to select
  HAVE_COPY_THREAD_TLS and instead simply continued to use copy_thread()
  and use the old calling convention. Removing this split cleans up the
  process creation codepaths and paves the way for implementing clone3()
  on such architectures since it requires the copy_thread_tls() calling
  convention.

  After having made each architectures support copy_thread_tls() this
  series simply renames that function back to copy_thread(). It also
  switches all architectures that call do_fork() directly over to
  _do_fork() and the struct kernel_clone_args calling convention. This
  is a corollary of switching the architectures that did not yet support
  it over to copy_thread_tls() since do_fork() is conditional on not
  supporting copy_thread_tls() (Mostly because it lacks a separate
  argument for tls which is trivial to fix but there's no need for this
  function to exist.).

  The do_fork() removal is in itself already useful as it allows to to
  remove the export of both do_fork() and _do_fork() we currently have
  in favor of only _do_fork(). This has already been discussed back when
  we added clone3(). The legacy clone() calling convention is - as is
  probably well-known - somewhat odd:

    #
    # ABI hall of shame
    #
    config CLONE_BACKWARDS
    config CLONE_BACKWARDS2
    config CLONE_BACKWARDS3

  that is aggravated by the fact that some architectures such as sparc
  follow the CLONE_BACKWARDSx calling convention but don't really select
  the corresponding config option since they call do_fork() directly.

  So do_fork() enforces a somewhat arbitrary calling convention in the
  first place that doesn't really help the individual architectures that
  deviate from it. They can thus simply be switched to _do_fork()
  enforcing a single calling convention. (I really hope that any new
  architectures will __not__ try to implement their own calling
  conventions...)

  Most architectures already have made a similar switch (m68k comes to
  mind).

  Overall this removes more code than it adds even with a good portion
  of added comments. It simplifies a chunk of arch specific assembly
  either by moving the code into C or by simply rewriting the assembly.

  Architectures that have been touched in non-trivial ways have all been
  actually boot and stress tested: sparc and ia64 have been tested with
  Debian 9 images. They are the two architectures which have been
  touched the most. All non-trivial changes to architectures have seen
  acks from the relevant maintainers. nios2 with a custom built
  buildroot image. h8300 I couldn't get something bootable to test on
  but the changes have been fairly automatic and I'm sure we'll hear
  people yell if I broke something there.

  All other architectures that have been touched in trivial ways have
  been compile tested for each single patch of the series via git rebase
  -x "make ..." v5.8-rc2. arm{64} and x86{_64} have been boot tested
  even though they have just been trivially touched (removal of the
  HAVE_COPY_THREAD_TLS macro from their Kconfig) because well they are
  basically "core architectures" and since it is trivial to get your
  hands on a useable image"

* tag 'fork-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  arch: rename copy_thread_tls() back to copy_thread()
  arch: remove HAVE_COPY_THREAD_TLS
  unicore: switch to copy_thread_tls()
  sh: switch to copy_thread_tls()
  nds32: switch to copy_thread_tls()
  microblaze: switch to copy_thread_tls()
  hexagon: switch to copy_thread_tls()
  c6x: switch to copy_thread_tls()
  alpha: switch to copy_thread_tls()
  fork: remove do_fork()
  h8300: select HAVE_COPY_THREAD_TLS, switch to kernel_clone_args
  nios2: enable HAVE_COPY_THREAD_TLS, switch to kernel_clone_args
  ia64: enable HAVE_COPY_THREAD_TLS, switch to kernel_clone_args
  sparc: unconditionally enable HAVE_COPY_THREAD_TLS
  sparc: share process creation helpers between sparc and sparc64
  sparc64: enable HAVE_COPY_THREAD_TLS
  fork: fold legacy_clone_args_valid() into _do_fork()

Pull thread updates from Christian Brauner:
 "This contains the changes to add the missing support for attaching to
  time namespaces via pidfds.

  Last cycle setns() was changed to support attaching to multiple
  namespaces atomically. This requires all namespaces to have a point of
  no return where they can't fail anymore.

  Specifically, <namespace-type>_install() is allowed to perform
  permission checks and install the namespace into the new struct nsset
  that it has been given but it is not allowed to make visible changes
  to the affected task. Once <namespace-type>_install() returns,
  anything that the given namespace type additionally requires to be
  setup needs to ideally be done in a function that can't fail or if it
  fails the failure must be non-fatal.

  For time namespaces the relevant functions that fell into this
  category were timens_set_vvar_page() and vdso_join_timens(). The
  latter could still fail although it didn't need to. This function is
  only implemented for vdso_join_timens() in current mainline. As
  discussed on-list (cf. [1]), in order to make setns() support time
  namespaces when attaching to multiple namespaces at once properly we
  changed vdso_join_timens() to always succeed. So vdso_join_timens()
  replaces the mmap_write_lock_killable() with mmap_read_lock().

  Please note that arm is about to grow vdso support for time namespaces
  (possibly this merge window). We've synced on this change and arm64
  also uses mmap_read_lock(), i.e. makes vdso_join_timens() a function
  that can't fail. Once the changes here and the arm64 changes have
  landed, vdso_join_timens() should be turned into a void function so
  it's obvious to callers and implementers on other architectures that
  the expectation is that it can't fail.

  We didn't do this right away because it would've introduced
  unnecessary merge conflicts between the two trees for no major gain.

  As always, tests included"

[1]: https://lore.kernel.org/lkml/20200611110221.pgd3r5qkjrjmfqa2@wittgenstein

* tag 'threads-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  tests: add CLONE_NEWTIME setns tests
  nsproxy: support CLONE_NEWTIME with setns()
  timens: add timens_commit() helper
  timens: make vdso_join_timens() always succeed

If the operation mode is non-zero and an external reference voltage is set,
first the operation mode is written to the advanced configuration register,
followed by the externel reference enable bit,
resetting the configuration mode to 0.

To fix this, first compose the value of the advanced configuration register
based on the configuration mode and the external reference voltage.
The advanced configuration register is then written to the device,
if it is different from the default register value (0x0).
Signed-off-by: Roy van Doormaal <roy.van.doormaal@prodrive-technologies.com>
Link: https://lore.kernel.org/r/20200728151846.231785-1-roy.van.doormaal@prodrive-technologies.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Pull execve updates from Eric Biederman:
 "During the development of v5.7 I ran into bugs and quality of
  implementation issues related to exec that could not be easily fixed
  because of the way exec is implemented. So I have been diggin into
  exec and cleaning up what I can.

  This cycle I have been looking at different ideas and different
  implementations to see what is possible to improve exec, and cleaning
  the way exec interfaces with in kernel users. Only cleaning up the
  interfaces of exec with rest of the kernel has managed to stabalize
  and make it through review in time for v5.9-rc1 resulting in 2 sets of
  changes this cycle.

   - Implement kernel_execve

   - Make the user mode driver code a better citizen

  With kernel_execve the code size got a little larger as the copying of
  parameters from userspace and copying of parameters from userspace is
  now separate. The good news is kernel threads no longer need to play
  games with set_fs to use exec. Which when combined with the rest of
  Christophs set_fs changes should security bugs with set_fs much more
  difficult"

* 'exec-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (23 commits)
  exec: Implement kernel_execve
  exec: Factor bprm_stack_limits out of prepare_arg_pages
  exec: Factor bprm_execve out of do_execve_common
  exec: Move bprm_mm_init into alloc_bprm
  exec: Move initialization of bprm->filename into alloc_bprm
  exec: Factor out alloc_bprm
  exec: Remove unnecessary spaces from binfmts.h
  umd: Stop using split_argv
  umd: Remove exit_umh
  bpfilter: Take advantage of the facilities of struct pid
  exit: Factor thread_group_exited out of pidfd_poll
  umd: Track user space drivers with struct pid
  bpfilter: Move bpfilter_umh back into init data
  exec: Remove do_execve_file
  umh: Stop calling do_execve_file
  umd: Transform fork_usermode_blob into fork_usermode_driver
  umd: Rename umd_info.cmdline umd_info.driver_name
  umd: For clarity rename umh_info umd_info
  umh: Separate the user mode driver and the user mode helper support
  umh: Remove call_usermodehelper_setup_file.
  ...

These macros are also present in the "include/linux/fpga/adi-axi-common.h"
file which is included in this driver.

This patch removes them from the AXI Fan Control driver. No sense in having
them in 2 places.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200803054311.98174-1-alexandru.ardelean@analog.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

The return value of pci_read_config_*() may not indicate a device error.
However, the value read by these functions is more likely to indicate
this kind of error. This presents two overlapping ways of reporting
errors and complicates error checking.

It is possible to move to one single way of checking for error if the
dependency on the return value of these functions is removed, then it
can later be made to return void.

Remove all uses of the return value of pci_read_config_*().
Check the actual value read for ~0. In this case, ~0 is an invalid
value thus it indicates some kind of error.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Link: https://lore.kernel.org/r/20200801112446.149549-11-refactormyself@gmail.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Pull audit updates from Paul Moore:
 "Aside from some smaller bug fixes, here are the highlights:

   - add a new backlog wait metric to the audit status message, this is
     intended to help admins determine how long processes have been
     waiting for the audit backlog queue to clear

   - generate audit records for nftables configuration changes

   - generate CWD audit records for for the relevant LSM audit records"

* tag 'audit-pr-20200803' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
  audit: report audit wait metric in audit status reply
  audit: purge audit_log_string from the intra-kernel audit API
  audit: issue CWD record to accompany LSM_AUDIT_DATA_* records
  audit: use the proper gfp flags in the audit_log_nfcfg() calls
  audit: remove unused !CONFIG_AUDITSYSCALL __audit_inode* stubs
  audit: add gfp parameter to audit_log_nfcfg
  audit: log nftables configuration change events
  audit: Use struct_size() helper in alloc_chunk

Pull selinux updates from Paul Moore:
 "Beyond the usual smattering of bug fixes, we've got three small
  improvements worth highlighting:

   - improved SELinux policy symbol table performance due to a reworking
     of the insert and search functions

   - allow reading of SELinux labels before the policy is loaded,
     allowing for some more "exotic" initramfs approaches

   - improved checking an error reporting about process
     class/permissions during SELinux policy load"

* tag 'selinux-pr-20200803' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  selinux: complete the inlining of hashtab functions
  selinux: prepare for inlining of hashtab functions
  selinux: specialize symtab insert and search functions
  selinux: Fix spelling mistakes in the comments
  selinux: fixed a checkpatch warning with the sizeof macro
  selinux: log error messages on required process class / permissions
  scripts/selinux/mdp: fix initial SID handling
  selinux: allow reading labels before policy is loaded

Pull seccomp updates from Kees Cook:
 "There are a bunch of clean ups and selftest improvements along with
  two major updates to the SECCOMP_RET_USER_NOTIF filter return:
  EPOLLHUP support to more easily detect the death of a monitored
  process, and being able to inject fds when intercepting syscalls that
  expect an fd-opening side-effect (needed by both container folks and
  Chrome). The latter continued the refactoring of __scm_install_fd()
  started by Christoph, and in the process found and fixed a handful of
  bugs in various callers.

   - Improved selftest coverage, timeouts, and reporting

   - Add EPOLLHUP support for SECCOMP_RET_USER_NOTIF (Christian Brauner)

   - Refactor __scm_install_fd() into __receive_fd() and fix buggy
     callers

   - Introduce 'addfd' command for SECCOMP_RET_USER_NOTIF (Sargun
     Dhillon)"

* tag 'seccomp-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (30 commits)
  selftests/seccomp: Test SECCOMP_IOCTL_NOTIF_ADDFD
  seccomp: Introduce addfd ioctl to seccomp user notifier
  fs: Expand __receive_fd() to accept existing fd
  pidfd: Replace open-coded receive_fd()
  fs: Add receive_fd() wrapper for __receive_fd()
  fs: Move __scm_install_fd() to __receive_fd()
  net/scm: Regularize compat handling of scm_detach_fds()
  pidfd: Add missing sock updates for pidfd_getfd()
  net/compat: Add missing sock updates for SCM_RIGHTS
  selftests/seccomp: Check ENOSYS under tracing
  selftests/seccomp: Refactor to use fixture variants
  selftests/harness: Clean up kern-doc for fixtures
  seccomp: Use -1 marker for end of mode 1 syscall list
  seccomp: Fix ioctl number for SECCOMP_IOCTL_NOTIF_ID_VALID
  selftests/seccomp: Rename user_trap_syscall() to user_notif_syscall()
  selftests/seccomp: Make kcmp() less required
  seccomp: Use pr_fmt
  selftests/seccomp: Improve calibration loop
  selftests/seccomp: use 90s as timeout
  selftests/seccomp: Expand benchmark to per-filter measurements
  ...

Pull uninitialized_var() macro removal from Kees Cook:
 "This is long overdue, and has hidden too many bugs over the years. The
  series has several "by hand" fixes, and then a trivial treewide
  replacement.

   - Clean up non-trivial uses of uninitialized_var()

   - Update documentation and checkpatch for uninitialized_var() removal

   - Treewide removal of uninitialized_var()"

* tag 'uninit-macro-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  compiler: Remove uninitialized_var() macro
  treewide: Remove uninitialized_var() usage
  checkpatch: Remove awareness of uninitialized_var() macro
  mm/debug_vm_pgtable: Remove uninitialized_var() usage
  f2fs: Eliminate usage of uninitialized_var() macro
  media: sur40: Remove uninitialized_var() usage
  KVM: PPC: Book3S PR: Remove uninitialized_var() usage
  clk: spear: Remove uninitialized_var() usage
  clk: st: Remove uninitialized_var() usage
  spi: davinci: Remove uninitialized_var() usage
  ide: Remove uninitialized_var() usage
  rtlwifi: rtl8192cu: Remove uninitialized_var() usage
  b43: Remove uninitialized_var() usage
  drbd: Remove uninitialized_var() usage
  x86/mm/numa: Remove uninitialized_var() usage
  docs: deprecated.rst: Add uninitialized_var()

Pull tasklets API update from Kees Cook:
 "These are the infrastructure updates needed to support converting the
  tasklet API to something more modern (and hopefully for removal
  further down the road).

  There is a 300-patch series waiting in the wings to get set out to
  subsystem maintainers, but these changes need to be present in the
  kernel first. Since this has some treewide changes, I carried this
  series for -next instead of paining Thomas with it in -tip, but it's
  got his Ack.

  This is similar to the timer_struct modernization from a while back,
  but not nearly as messy (I hope). :)

   - Prepare for tasklet API modernization (Romain Perier, Allen Pais,
     Kees Cook)"

* tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  tasklet: Introduce new initialization API
  treewide: Replace DECLARE_TASKLET() with DECLARE_TASKLET_OLD()
  usb: gadget: udc: Avoid tasklet passing a global

Pull automatic variable initialization updates from Kees Cook:
 "This adds the "zero" init option from Clang, which is being used
  widely in production builds of Android and Chrome OS (though it also
  keeps the "pattern" init, which is better for debug builds).

   - Introduce CONFIG_INIT_STACK_ALL_ZERO (Alexander Potapenko)"

* tag 'var-init-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  security: allow using Clang's zero initialization for stack variables

Pull gcc plugin updates from Kees Cook:
 "Primarily improvements to STACKLEAK from Alexander Popov, along with
  some additional cleanups.

    - Update URLs for HTTPS scheme where available (Alexander A. Klimov)

   - Improve STACKLEAK code generation on x86 (Alexander Popov)"

* tag 'gcc-plugins-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: Replace HTTP links with HTTPS ones
  gcc-plugins/stackleak: Add 'verbose' plugin parameter
  gcc-plugins/stackleak: Use asm instrumentation to avoid useless register saving
  ARM: vdso: Don't use gcc plugins for building vgettimeofday.c
  gcc-plugins/stackleak: Don't instrument itself