If esp*_offload module is loaded, outbound packets take the
GSO code path, being encapsulated at layer 3, but encrypted
in layer 2. validate_xmit_xfrm calls esp*_xmit for that.

esp*_xmit was wrongfully detecting these packets as going
through hardware crypto offload, while in fact they should
be encrypted in software, causing plaintext leakage to
the network, and also dropping at the receiver side.

Perform the encryption in esp*_xmit, if the SA doesn't have
a hardware offload_handle.

Also, align esp6 code to esp4 logic.

Fixes: fca11ebd ("esp4: Reorganize esp_output")
Fixes: 383d0350 ("esp6: Reorganize esp_output")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

The check for xo being null is incorrect, currently it is checking
for non-null, it should be checking for null.

Detected with CoverityScan, CID#1429349 ("Dereference after null check")

Fixes: 7862b405 ("esp: Add gso handlers for esp4 and esp6")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

On IPsec hardware offloading, we already get a secpath with
valid state attached when the packet enters the GRO handlers.
So check for hardware offload and skip the state lookup in this
case.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

Both esp4 and esp6 used to assume that the SKB payload is encrypted
and therefore the inner_network and inner_transport offsets are
not relevant.
When doing crypto offload in the NIC, this is no longer the case
and the NIC driver needs these offsets so it can do TX TCP checksum
offloading.
This patch sets the inner_network and inner_transport members of
the SKB, as well as encapsulation, to reflect the actual positions
of these headers, and removes them only once encryption is done
on the payload.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

When we do IPsec offloading, we need a fallback for
packets that were targeted to be IPsec offloaded but
rerouted to a device that does not support IPsec offload.
For that we add a function that checks the offloading
features of the sending device and and flags the
requirement of a fallback before it calls the IPsec
output function. The IPsec output function adds the IPsec
trailer and does encryption if needed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

We need a fallback algorithm for crypto offloading to a NIC.
This is because packets can be rerouted to other NICs that
don't support crypto offloading. The fallback is going to be
implemented at layer2 where we know the final output device
but can't handle asynchronous returns fron the crypto layer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

This patch adds functions that handles IPsec sequence
numbers for GSO segments and TSO offloading. We need
to calculate and update the sequence numbers based
on the segments that GSO/TSO will generate. We need
this to keep software and hardware sequence number
counter in sync.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

This patch extends the xfrm_type by an encap function pointer
and implements esp4_gso_encap and esp6_gso_encap. These functions
doing the basic esp encapsulation for a GSO packet. In case the
GSO packet needs to be segmented in software, we add gso_segment
functions. This codepath is going to be used on esp hardware
offloads.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

We need a fallback for ESP at layer 2, so split esp6_output
into generic functions that can be used at layer 3 and layer 2
and use them in esp_output. We also add esp6_xmit which is
used for the layer 2 fallback.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

We need a fallback for ESP at layer 2, so split esp_output
into generic functions that can be used at layer 3 and layer 2
and use them in esp_output. We also add esp_xmit which is
used for the layer 2 fallback.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

We are going to export the ipv4 and the ipv6
version of esp_input_done2. They are not static
anymore and can't have the same name. So rename
the ipv6 version to esp6_input_done2.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

This patch adds all the bits that are needed to do
IPsec hardware offload for IPsec states and ESP packets.
We add xfrmdev_ops to the net_device. xfrmdev_ops has
function pointers that are needed to manage the xfrm
states in the hardware and to do a per packet
offloading decision.

Joint work with:
Ilan Tayari <ilant@mellanox.com>
Guy Shapiro <guysh@mellanox.com>
Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

This patch adds a gso_segment and xmit callback for the
xfrm_mode and implement these functions for tunnel and
transport mode.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

This is needed for the upcomming IPsec device offloading.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

We add a struct  xfrm_type_offload so that we have the offloaded
codepath separated to the non offloaded codepath. With this the
non offloade and the offloaded codepath can coexist.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

This patch adds netdev features to configure IPsec offloads.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

Ursula Braun says:

====================
net/smc: patches for net-next

here are some patches for net/smc. Most important are
improvements for socket closing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

smc specifies IB_SEND_INLINE for IB_WR_SEND ib_post_send calls, but
provides a mapped buffer to be sent. This is inconsistent, since
IB_SEND_INLINE works without mapped buffer. Problem has not been
detected in the past, because tests had been limited to Connect X3 cards
from Mellanox, whose mlx4 driver just ignored the IB_SEND_INLINE flag.
For now, the IB_SEND_INLINE flag is removed.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure sockets never accepted are removed cleanly.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

unhash is already called in sock_put_work. Remove the second call.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

State SMC_CLOSED should be reached only, if ConnClosed has been sent to
the peer. If ConnClosed is received from the peer, a socket with
shutdown SHUT_WR done, switches errorneously to state SMC_CLOSED, which
means the peer socket is dangling. The local SMC socket is supposed to
switch to state APPFINCLOSEWAIT to make sure smc_close_final() is called
during socket close.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several state changes occur during SMC socket closing. Currently
state changes triggered locally occur in process context with
lock_sock() taken while state changes triggered by peer occur in
tasklet context with bh_lock_sock() taken. bh_lock_sock() does not
wait till a lock_sock(() task in process context is finished. This
may lead to races in socket state transitions resulting in dangling
SMC-sockets, or it may lead to duplicate SMC socket freeing.
This patch introduces a closing worker to run all state changes under
lock_sock().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wake up reading file descriptors for a closing socket as well, otherwise
some socket applications may stall.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If peer indicates write_blocked, the cursor state of the received data
should be send to the peer immediately (in smc_tx_consumer_update()).
Afterwards the write_blocked indicator is cleared.

If there is no free slot for another write request, sending is postponed
to worker smc_tx_work, and the write_blocked indicator is not cleared.
Therefore another clearing check is needed in smc_tx_work().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SMC requires an active ib port on the RoCE device.
smc_pnet_find_roce_resource() determines the matching RoCE device port
according to the configured PNET table. Do not return the found
RoCE device port, if it is not flagged active.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The global event handler is created only, if the ib_device has already
been used by at least one link group. It is guaranteed that there exists
the corresponding entry in the smc_ib_devices list. Get rid of this
superfluous check.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes an outdated comment.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the submission of the lastest multiple buffer patch set, this fix was lost.
I am sending this patch to put it right again. The fix was originally proposed
by Arnd Bergmann.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BPF helper functions access socket fields through skb->sk. This is not
set in ingress cgroup and socket filters. The association is only made
in skb_set_owner_r once the filter has accepted the packet. Sk is
available as socket lookup has taken place.

Temporarily set skb->sk to sk in these cases.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the return value check which testing the wrong variable
in devlink_dpipe_header_put().

Fixes: 1555d204 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
more s390/net updates

here's a second batch of s390/net patches for net-next.
A mixed bunch of qeth cleanups, and a few patches to add support for
ETHTOOL_GLINKSETTINGS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

prepare() and complete() are not implemented by any discipline, so just
drop all the indirection.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LINK_MODE_* replaces the u32-limited SUPPORTED_* / ENABLED_*
definitions.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

get_settings() is deprecated and lacks support for higher link
speeds, so implement get_link_ksettings() instead.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for moving to get_link_ksettings(), clean up how
we build the supported and advertised port/speed masks.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. a buffer has 16 is_header flags, because that's its # of elements
2. replace the last occurrence of QETH_HEADER_SIZE, and remove it
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ndo_start_xmit() expects us to return netdev_tx_t here...
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'elements_needed' is not used in qeth_do_send_packet_fast(),
so consequently remove it.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Duplicated code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Identical code, we just need to call a layer-specific hook
to process any received buffer.

qeth_buffer_reclaim_work() is shuffled around to avoid a
forward declaration for qeth_queue_input_buffer().
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>