CPUFreq core has new infrastructure that would guarantee serialized calls to
target() or target_index() callbacks. These are called
cpufreq_freq_transition_begin() and cpufreq_freq_transition_end().

This patch converts existing drivers to use these new set of routines.
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Whenever we change the frequency of a CPU, we call the PRECHANGE and POSTCHANGE
notifiers. They must be serialized, i.e. PRECHANGE and POSTCHANGE notifiers
should strictly alternate, thereby preventing two different sets of PRECHANGE or
POSTCHANGE notifiers from interleaving arbitrarily.

The following examples illustrate why this is important:

Scenario 1:
-----------
A thread reading the value of cpuinfo_cur_freq, will call
__cpufreq_cpu_get()->cpufreq_out_of_sync()->cpufreq_notify_transition()

The ondemand governor can decide to change the frequency of the CPU at the same
time and hence it can end up sending the notifications via ->target().

If the notifiers are not serialized, the following sequence can occur:
- PRECHANGE Notification for freq A (from cpuinfo_cur_freq)
- PRECHANGE Notification for freq B (from target())
- Freq changed by target() to B
- POSTCHANGE Notification for freq B
- POSTCHANGE Notification for freq A

We can see from the above that the last POSTCHANGE Notification happens for freq
A but the hardware is set to run at freq B.

Where would we break then?: adjust_jiffies() in cpufreq.c & cpufreq_callback()
in arch/arm/kernel/smp.c (which also adjusts the jiffies). All the
loops_per_jiffy calculations will get messed up.

Scenario 2:
-----------
The governor calls __cpufreq_driver_target() to change the frequency. At the
same time, if we change scaling_{min|max}_freq from sysfs, it will end up
calling the governor's CPUFREQ_GOV_LIMITS notification, which will also call
__cpufreq_driver_target(). And hence we end up issuing concurrent calls to
->target().

Typically, platforms have the following logic in their ->target() routines:
(Eg: cpufreq-cpu0, omap, exynos, etc)

A. If new freq is more than old: Increase voltage
B. Change freq
C. If new freq is less than old: decrease voltage

Now, if the two concurrent calls to ->target() are X and Y, where X is trying to
increase the freq and Y is trying to decrease it, we get the following race
condition:

X.A: voltage gets increased for larger freq
Y.A: nothing happens
Y.B: freq gets decreased
Y.C: voltage gets decreased
X.B: freq gets increased
X.C: nothing happens

Thus we can end up setting a freq which is not supported by the voltage we have
set. That will probably make the clock to the CPU unstable and the system might
not work properly anymore.

This patch introduces a set of synchronization primitives to serialize frequency
transitions, which are to be used as shown below:

cpufreq_freq_transition_begin();

//Perform the frequency change

cpufreq_freq_transition_end();

The _begin() call sends the PRECHANGE notification whereas the _end() call sends
the POSTCHANGE notification. Also, all the necessary synchronization is handled
within these calls. In particular, even drivers which set the ASYNC_NOTIFICATION
flag can also use these APIs for performing frequency transitions (ie., you can
call _begin() from one task, and call the corresponding _end() from a different
task).

The actual synchronization underneath is not that complicated:

The key challenge is to allow drivers to begin the transition from one thread
and end it in a completely different thread (this is to enable drivers that do
asynchronous POSTCHANGE notification from bottom-halves, to also use the same
interface).

To achieve this, a 'transition_ongoing' flag, a 'transition_lock' spinlock and a
wait-queue are added per-policy. The flag and the wait-queue are used in
conjunction to create an "uninterrupted flow" from _begin() to _end(). The
spinlock is used to ensure that only one such "flow" is in flight at any given
time. Put together, this provides us all the necessary synchronization.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Ensure that no timer callback is running since we are about to free
the timer structure.  We cannot guarantee that the call back is called
on the CPU where the timer is running.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

During suspend, we first stop governors and then suspend cpufreq drivers and
resume must be exactly opposite of that. i.e. resume drivers first and then
start governors.

But the current code in resume enables governors first and then resume drivers.
Fix it be changing code sequence there.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Change to use the new ->stop_cpu() callback to do clean up during CPU
hotplug. The requested P state for an offline core will be used by the
hardware coordination function to select the package P state. If the
core is under load when it is offlined it will fix the package P state
floor to the requested P state of offline core.
Reported-by: Patrick Marlier <patrick.marlier@gmail.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This callback allows the driver to do clean up before the CPU is
completely down and its state cannot be modified.  This is used
by the intel_pstate driver to reduce the requested P state prior to
the core going away.  This is required because the requested P state
of the offline core is used to select the package P state. This
effectively sets the floor package P state to the requested P state on
the offline core.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
[rjw: Minor modifications]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Remove unnecessary braces from a single statement.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Fix 2 checkpatch errors about using assignment in if condition,
1 checkpatch error about a required space after comma
and 3 warnings about line over 80 characters.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

According to the data provided by HW Team, at least 12 internal platform
clock cycles are required to stabilize a DFS clock switch on FSL e500mc Socs.
This patch replaces the CPUFREQ_ETERNAL with appropriate HW clock transition
latency to make DFS governors work normally on Freescale e500mc boards.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Two cpufreq notifiers CPUFREQ_RESUMECHANGE and CPUFREQ_SUSPENDCHANGE have
not been used for some time, so remove them to clean up code a bit.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

cpufreq drivers that provide the ->setpolicy() callback are supposed
to have integrated governors, so they don't need to set ->target()
or ->target_index() and may confuse the core if any of these callbacks
is present.

For this reason, add a check preventing ->setpolicy cpufreq drivers
from registering if they have non-NULL ->target or ->target_index.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

We have a per-CPU variable for managing which cluster a CPU belongs to.
Currently, physical_cluster is set for policy->cpu only which leads to
the following on some SoC's:

 - There are two clusters:
   - Cluster 0 has four ARM Cortex A7 CPUs (slower ones): 0,1,2,3
   - Cluster 1 has four ARM Cortex A15 CPUs (faster ones): 4,5,6,7
 - CPUs are booted in order 0,1..7 and so initially policy->cpu for A7 cluster
   would be 0 and for A15 cluster would be 4.
 - Now CPU4 (i.e. A15_0) is hotplugged out and so policy->cpu for A15 cluster
   becomes 5 (i.e. A15_1).
 - But physical cluster is only set for CPU0 and CPU4 in ARM big LITTLE driver
   and isn't updated.
 - Now freq change request comes for A15 cluster and we would try to update freq
   of physical_cluster of CPU5, i.e. A15_1. And it is currently set to zero
   (default value of uninitialized global variables).
 - And so we actually try to change freq of A7 cluster instead of A15.
 - This also results in kernel crash as sometimes we might request freq above
   A7's limit and CPU may behave badly..

Fix this by initializing physical_cluster for all CPUs of a policy.

Based on previous work by Xin Wang.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently vexpress big LITTLE driver selects ARM_BIG_LITTLE_CPUFREQ, so
if CONFIG_BIG_LITTLE isn't enabled and CONFIG_ARM_VEXPRESS_SPC_CPUFREQ
is enabled, we get the following build warnings:

warning: (ARM_VEXPRESS_SPC_CPUFREQ) selects ARM_BIG_LITTLE_CPUFREQ which has
unmet direct dependencies (ARCH_HAS_CPUFREQ && CPU_FREQ && (ARM || ARM64) && ARM
&& BIG_LITTLE && ARM_CPU_TOPOLOGY && HAVE_CLK)

To fix this, make ARM_VEXPRESS_SPC_CPUFREQ depend on ARM_BIG_LITTLE_CPUFREQ
instead of selecting it.

This also moves the entry for ARM_VEXPRESS_SPC_CPUFREQ along with other
big LITTLE config entries.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

After commit da60ce9f (cpufreq: call cpufreq_driver->get() after
calling ->init()) __cpufreq_add_dev() sometimes fails for CPUs handled
by intel_pstate, because that driver may return 0 from its ->get()
callback if it has not run long enough to collect enough samples on the
given CPU.  That didn't happen before commit da60ce9f which added
policy->cur initialization to __cpufreq_add_dev() to help reduce code
duplication in other cpufreq drivers.

However, the code added by commit da60ce9f need not be executed
for cpufreq drivers having the ->setpolicy callback defined, because
the subsequent invocation of cpufreq_set_policy() will use that
callback to initialize the policy anyway and it doesn't need
policy->cur to be initialized upfront.  The analogous code in
cpufreq_update_policy() is also unnecessary for cpufreq drivers
having ->setpolicy set and may be skipped for them as well.

Since intel_pstate provides ->setpolicy, skipping the upfront
policy->cur initialization for cpufreq drivers with that callback
set will cover intel_pstate and the problem it's been having after
commit da60ce9f will be addressed.

Fixes: da60ce9f (cpufreq: call cpufreq_driver->get() after calling ->init())
References: https://bugzilla.kernel.org/show_bug.cgi?id=71931Reported-and-tested-by: Patrik Lundquist <patrik.lundquist@gmail.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

As multiplatform build is being adopted by more and more
ARM platforms, initcall function should be used very carefully.
For example, when SPEAr cpufreq driver is enabled on a kernel
booted on a non-SPEAr board, we will get following boot time error:

	spear_cpufreq: Invalid cpufreq_tbl

To eliminate this undesired the effect, the patch changes SPEAr
driver to have it instantiated as a platform_driver. Then it will
only run on platforms that create the platform_device "spear-cpufreq".

This patch also creates platform node for SPEAr13xx boards.
Reported-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

We have used 'frozen' variable/function parameter at many places to
distinguish between CPU offline/online on suspend/resume vs sysfs
removals. We now have another variable cpufreq_suspended which can
be used in these cases, so we can get rid of all those variables or
function parameters.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

cpufreq_generic_exit() is empty now and can be deleted.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

freq table is not per CPU but per policy, so it makes more sense to
keep it within struct cpufreq_policy instead of a per-cpu variable.

This patch does it. Over that, there is no need to set policy->freq_table
to NULL in ->exit(), as policy structure is going to be freed soon.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

 - Add missing newlines
 - Coalesce format fragments
 - Convert printks to pr_<level>
 - Align arguments
Based-on-patch-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull ARM SoC fixes from from Olof Johansson:
 "A collection of fixes for ARM platforms.  A little large due to us
  missing to do one last week, but there's nothing in particular here
  that is in itself large and scary.

  Mostly a handful of smaller fixes all over the place.  The majority is
  made up of fixes for OMAP, but there are a few for others as well.  In
  particular, there was a decision to rename a binding for the Broadcom
  pinctrl block that we need to go in before the final release since we
  then treat it as ABI"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
  ARM: tegra: add LED options back into tegra_defconfig
  ARM: dts: omap3-igep: fix boot fail due wrong compatible match
  ARM: OMAP3: Fix pinctrl interrupts for core2
  pinctrl: Rename Broadcom Capri pinctrl binding
  pinctrl: refer to updated dt binding string.
  Update dtsi with new pinctrl compatible string
  ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
  ARM: OMAP2+: Add support for thumb mode on DT booted N900
  ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
  ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
  ARM: DRA7: hwmod data: correct the sysc data for spinlock
  ARM: OMAP5: PRM: Fix reboot handling
  ARM: sunxi: dt: Change the touchscreen compatibles
  ARM: sun7i: dt: Fix interrupt trigger types

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

   - Fix another nfs4_sequence corruptor in RELEASE_LOCKOWNER
   - Fix an Oopsable delegation callback race
   - Fix another bad stateid infinite loop
   - Fail the data server I/O is the stateid represents a lost lock
   - Fix an Oopsable sunrpc trace event"

* tag 'nfs-for-3.14-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: Fix oops when trace sunrpc_task events in nfs client
  NFSv4: Fail the truncate() if the lock/open stateid is invalid
  NFSv4.1 Fail data server I/O if stateid represents a lost lock
  NFSv4: Fix the return value of nfs4_select_rw_stateid
  NFSv4: nfs4_stateid_is_current should return 'true' for an invalid stateid
  NFS: Fix a delegation callback race
  NFSv4: Fix another nfs4_sequence corruptor

Pull USB fixes from Greg KH:
 "Here are 4 USB fixes for your current tree.

  Two of them are reverts to hopefully resolve the nasty XHCI
  regressions we have been having on some types of devices.  The other
  two are quirks for some Logitech video devices"

* tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  Revert "USBNET: ax88179_178a: enable tso if usb host supports sg dma"
  Revert "xhci 1.0: Limit arbitrarily-aligned scatter gather."
  usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests
  usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e

Pull staging driver tree fix from Greg KH:
 "Here is a single staging driver fix for your tree.

  It resolves an issue with arbritary writes to memory if a specific
  driver is loaded"

* tag 'staging-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging/cxt1e1/linux.c: Correct arbitrary memory write in c4_ioctl()

This fixes CVE-2014-0102.

The following command sequence produces an oops:

	keyctl new_session
	i=`keyctl newring _ses @s`
	keyctl link @s $i

The problem is that search_nested_keyrings() sees two keyrings that have
matching type and description, so keyring_compare_object() returns true.
s_n_k() then passes the key to the iterator function -
keyring_detect_cycle_iterator() - which *should* check to see whether this is
the keyring of interest, not just one with the same name.

Because assoc_array_find() will return one and only one match, I assumed that
the iterator function would only see an exact match or never be called - but
the iterator isn't only called from assoc_array_find()...

The oops looks something like this:

	kernel BUG at /data/fs/linux-2.6-fscache/security/keys/keyring.c:1003!
	invalid opcode: 0000 [#1] SMP
	...
	RIP: keyring_detect_cycle_iterator+0xe/0x1f
	...
	Call Trace:
	  search_nested_keyrings+0x76/0x2aa
	  __key_link_check_live_key+0x50/0x5f
	  key_link+0x4e/0x85
	  keyctl_keyring_link+0x60/0x81
	  SyS_keyctl+0x65/0xe4
	  tracesys+0xdd/0xe2

The fix is to make keyring_detect_cycle_iterator() check that the key it
has is the key it was actually looking for rather than calling BUG_ON().

A testcase has been included in the keyutils testsuite for this:

	http://git.kernel.org/cgit/linux/kernel/git/dhowells/keyutils.git/commit/?id=891f3365d07f1996778ade0e3428f01878a1790bReported-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull thermal fixes from Zhang Rui:
 "Specifics:

   - Update the help text of INT3403 Thermal driver, which was not
     friendly to users.  From Zhang Rui.

   - The "type" sysfs attribute of x86_pkg_temp_thermal registered
     thermal zones includes an instance number, which makes the
     thermal-to-hwmon bridge fails to group them all in a single hwmon
     device.  Fixed by Jean Delvare.

   - The hwmon device registered by x86_pkg_temp_thermal driver is
     redundant because the temperature value reported by
     x86_pkg_temp_thermal is already reported by the coretemp driver.
     Fixed by Jean Delvare.

   - Fix a problem that the cooling device can not be updated properly
     if it is initialized at max cooling state.  From Ni Wade.

   - Fix a problem that OF registered thermal zones are running without
     thermal governors.  From Zhang Rui.

   - Commit beeb5a1e ("thermal: rcar-thermal: Enable driver
     compilation with COMPILE_TEST") broke build on archs wihout io
     memory.  Thus make it depend on HAS_IOMEM to bypass build failures.
     Fixed by Richard Weinberger"

* 'for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  Thermal: thermal zone governor fix
  Thermal: Allow first update of cooling device state
  thermal,rcar_thermal: Add dependency on HAS_IOMEM
  x86_pkg_temp_thermal: Fix the thermal zone type
  x86_pkg_temp_thermal: Do not expose as a hwmon device
  Thermal: update INT3404 thermal driver help text

Pull spi fixes from Mark Brown:
 "A scattering of driver specific fixes here.

  The fixes from Axel cover bitrot in apparently unmaintained drivers,
  the at79 bug is fixing a glitch on /CS during initialisation of some
  devices which could break some slaves and the remainder are fixes for
  recently introduced bugs from the past release cycle or so"

* tag 'spi-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: atmel: add missing spi_master_{resume,suspend} calls to PM callbacks
  spi: coldfire-qspi: Fix getting correct address for *mcfqspi
  spi: fsl-dspi: Fix getting correct address for master
  spi: spi-ath79: fix initial GPIO CS line setup
  spi: spi-imx: spi_imx_remove: do not disable disabled clocks
  spi-topcliff-pch: Fix probing when DMA mode is used
  spi/topcliff-pch: Fix DMA channel

Pull SCSI target fixes from Nicholas Bellinger:
 "This series addresses a number of outstanding issues wrt to active I/O
  shutdown using iser-target.  This includes:

   - Fix a long standing tpg_state bug where a tpg could be referenced
     during explicit shutdown (v3.1+ stable)
   - Use list_del_init for iscsi_cmd->i_conn_node so list_empty checks
     work as expected (v3.10+ stable)
   - Fix a isert_conn->state related hung task bug + ensure outstanding
     I/O completes during session shutdown.  (v3.10+ stable)
   - Fix isert_conn->post_send_buf_count accounting for RDMA READ/WRITEs
     (v3.10+ stable)
   - Ignore FRWR completions during active I/O shutdown (v3.12+ stable)
   - Fix command leakage for interrupt coalescing during active I/O
     shutdown (v3.13+ stable)

  Also included is another DIF emulation fix from Sagi specific to
  v3.14-rc code"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  Target/sbc: Fix sbc_copy_prot for offset scatters
  iser-target: Fix command leak for tx_desc->comp_llnode_batch
  iser-target: Ignore completions for FRWRs in isert_cq_tx_work
  iser-target: Fix post_send_buf_count for RDMA READ/WRITE
  iscsi/iser-target: Fix isert_conn->state hung shutdown issues
  iscsi/iser-target: Use list_del_init for ->i_conn_node
  iscsi-target: Fix iscsit_get_tpg_from_np tpg_state bug

Revert commit 3130497f ("ACPI / sleep: pm_power_off needs more
sanity checks to be installed") that breaks power ACPI power off on a
lot of systems, because it checks wrong registers.

Fixes: 3130497f ("ACPI / sleep: pm_power_off needs more sanity checks to be installed")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'omap-for-v3.14/fixes-dt-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:

Two omap3430 vs 3630 device tree regression fixes for
issues booting 3430 based boards.

* tag 'omap-for-v3.14/fixes-dt-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
  ARM: dts: omap3-igep: fix boot fail due wrong compatible match
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge 'bcm pinctrl rename' From Christin Daudt:

Rename pinctrl dt binding to restore consistency with other bcm mobile
bindings.

* tag 'bcm-for-3.14-pinctrl-reduced-rename' of git://github.com/broadcom/bcm11351:
  pinctrl: Rename Broadcom Capri pinctrl binding
  pinctrl: refer to updated dt binding string.
  Update dtsi with new pinctrl compatible string
  + Linux 3.14-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>

Allwinner fixes from Maxime Ripard:

Two fixes for device trees additions that got added in 3.14. One fixes the
interrupt types of some IPs, the other fixes up a compatible that got
introduced during 3.14

* tag 'sunxi-fixes-for-3.14' of https://github.com/mripard/linux:
  ARM: sunxi: dt: Change the touchscreen compatibles
  ARM: sun7i: dt: Fix interrupt trigger types
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull cgroup fixes from Tejun Heo:
 "Two cpuset locking fixes from Li.  Both tagged for -stable"

* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cpuset: fix a race condition in __cpuset_node_allowed_softwall()
  cpuset: fix a locking issue in cpuset_migrate_mm()

Pull libata fixes from Tejun Heo:
 "Just a couple patches blacklisting more broken devices"

* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8 (2BA30001)
  libata: disable queued TRIM for Crucial M500 mSATA SSDs

Pull workqueue fix from Tejun Heo:
 "This pull request contains a workqueue usage fix for firewire.

  For quite a long time now, workqueue only treats two work items
  identical iff both their addresses and callbacks match.  This is to
  avoid introducing false dependency through the work item being
  recycled while being executed.  This changes non-reentrancy guarantee
  for the users of PREPARE[_DELAYED]_WORK() - if the function changes,
  reentrancy isn't guaranteed against the previous instance.  Firewire
  depended on such nonreentrancy guarantee.

  This is fixed by doing the work item multiplexing from firewire proper
  while keeping the work function unchanged"

* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  firewire: don't use PREPARE_DELAYED_WORK

Pull firewire fixes from Stefan Richter:
 "Fix a use-after-free regression since v3.4 and an initialization
  regression since v3.10"

* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: ohci: fix probe failure with Agere/LSI controllers
  firewire: net: fix use after free

Pull clk driver fix from Mike Turquette:
 "Single fix for a clock driver merged in 3.14-rc1.  Without this fix
  the CPU frequency cannot be scaled"

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
  clk: shmobile: rcar-gen2: Use kick bit to allow Z clock frequency change

Pull ACPI and power management fixes from Rafael Wysocki:

 - ACPI tables in some BIOSes list device resources with size equal to
   0, which doesn't make sense, so we should ignore them, but instead we
   try to use them and mangle things completely.  Fix from Zhang Rui.

 - Several models of Samsung laptops accumulate EC events when they are
   in sleep states which leads to EC buffer overflows that prevent new
   events from being signaled after system resume or reboot.  This has
   been affecting many users for quite a while and may be addressed by
   clearing the EC buffer during system resume and system startup on
   those machines.  From Kieran Clancy.

 - If the ACPI sleep control and status registers are not present (which
   happens if the Hardware Reduced ACPI mode bit is set in the ACPI
   tables, but also may result from BIOS bugs), we should not try to use
   ACPI to power off the system and ACPI S5 should not be listed as
   supported.  Fix from Aubrey Li.

 - There's a race condition in cpufreq_get() that leads to a kernel
   crash if that function is called at a wrong time.  Fix from Aaron
   Plattner.

 - cpufreq policy objects have to be initialized entirely before they
   are first accessed by their users which isn't the case currently and
   that potentially leads to various kinds of breakage that is difficult
   to debug.  Fix from Viresh Kumar.

 - Locking is missing in __cpufreq_add_dev() which leads to a race
   condition that may trigger a kernel crash.  Fix from Viresh Kumar.

* tag 'pm+acpi-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / EC: Clear stale EC events on Samsung systems
  cpufreq: Initialize governor for a new policy under policy->rwsem
  cpufreq: Initialize policy before making it available for others to use
  cpufreq: use cpufreq_cpu_get() to avoid cpufreq_get() race conditions
  ACPI / sleep: pm_power_off needs more sanity checks to be installed
  ACPI / resources: ignore invalid ACPI device resources

It's an enum, not a #define, you can't use it in asm files.

Introduced in commit 5fa10196 ("x86: Ignore NMIs that come in during
early boot"), and sadly I didn't compile-test things like I should have
before pushing out.

My weak excuse is that the x86 tree generally doesn't introduce stupid
things like this (and the ARM pull afterwards doesn't cause me to do a
compile-test either, since I don't cross-compile).

Cc: Don Zickus <dzickus@redhat.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>