Accessing the CIAA/D register can block access to the PCI config space.

This patch removes the read/write operations to the CIAA/D registers
and makes use of standard kernel functions for accessing the PCI config
space.

In addition it moves ixgbevf_check_for_bad_vf() into the watchdog subtask
which reduces the frequency of the checks.

CC: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Attempt to look up the MAC address in Open Firmware on systems that
support it. On SPARC resort to using the IDPROM if no OF address is
found.
Signed-off-by: Martin K Petersen <martin.petersen@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up the tail writes for the ixgbe descriptor queues.  The
current implementation had me confused as I wasn't sure if it was still
making use of the surprise remove logic or not.

It also adds the mmiowb which is needed on ia64, mips, and a couple other
architectures in order to synchronize the MMIO writes with the Tx queue
_xmit_lock spinlock.

Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.

It also cleans up how we clear the descriptor status bits.  Previously they
were zeroed as a part of clearing the hdr_addr.  However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems.  Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared.  As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.

Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When we write the GSO meta-data in tun_get_user we end up advancing
the IO vector twice, thus exhausting the user buffer before we can
finish writing the packet.

Fixes: f5ff53b4 ("{macvtap,tun}_get_user(): switch to iov_iter")
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
introduce rocker switch driver with hardware accelerated datapath api - phase 1: bridge fdb offload

This patchset is just the first phase of switch and switch-ish device
support api in kernel. Note that the api will extend.

So what this patchset includes:
- introduce switchdev api skeleton for implementing switch drivers
- introduce rocker switch driver which implements switchdev api fdb and
  bridge set/get link ndos

As to the discussion if there is need to have specific class of device
representing the switch itself, so far we found no need to introduce that.
But we are generally ok with the idea and when the time comes and it will
be needed, it can be easily introduced without any disturbance.

This patchset introduces switch id export through rtnetlink and sysfs,
which is similar to what we have for port id in SR-IOV. I will send iproute2
patchset for showing the switch id for port netdevs once this is applied.
This applies also for the PF_BRIDGE and fdb iproute2 patches.

iproute2 patches are now available here:
https://github.com/jpirko/iproute2-rocker

For detailed description and version history, please see individual patches.

In v4 I reordered the patches leaving rocker patches on the end of the patchset.

In v5 I only fixed whitespace issues of patch #13

We have a TODO for related items we want to work on in near future:
https://etherpad.wikimedia.org/p/netdev-swdev-todo
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Silences various sparse warnings
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rocker ports will use new "swdev" hwmode for bridge port offload policy.
Current supported policy settings are BR_LEARNING and BR_LEARNING_SYNC.
User can turn on/off device port FDB learning and syncing to bridge.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add L2 bridge offloading support to rocker driver.  Here, the Linux bridge
driver is used to collect swdev ports into a tagged (or untagged) VLAN
bridge.  The switchdev will offload from the bridge driver the following L2
bridging functions:

 - Learning of neighbor MAC addresses on VLAN X  Learned mac/vlan is
installed in bridge FDB.  (And removed when device unlearns mac/vlan).
Learning must be turned off on each bridge port to disable the feature in
the bridge driver.

- Flooding of multicast/broadcast and unknown unicast pkts to (STP)
active ports in bridge.  The bridge driver is unaware of the flooding happening
at the device level.  Flooding must be turned off on each bridge port to
disable the feature on the bridge driver.

- STP port state is pushed down to driver/device.  The bridge still processes
STP BDPUs and maintains port STP state (for all VLANs in bridge), but
the driver/device must be notified of port STP state change to program
the device.

Multiple (VLAN) bridges are supported.  The device (implemented per
the OF-DPA spec) must use a portion of the VLAN namespace for
internal VLANs.  Right now, the upper 255 VLANs (0xf00 to 0xffe) are
used as internal VLAN IDs for untagged traffic and are not available
as port VLANs.

The driver uses the following interfaces:

1. To track VLAN add/del on ports in bridge:

.ndo_vlan_rx_add_vid
.ndo_vlan_rx_kill_vid

2. To track port add/del membership in bridge:

NETDEV_CHANGEUPPER netdevice notifier

3. To catch static FDB entries installed on bridge/vlan by user using netlink:

.ndo_fdb_add
.ndo_fdb_del

4. To be notified on port STP state change:

.ndo_switch_port_stp_update

5. To notify bridge driver on learned/forgotten mac/vlans on bridge port:

br_fdb_external_learn_add
br_fdb_external_learn_del
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rocker driver maintains 4 hash tables: flows, groups, FDB, and VLANs.

Flow and group tables track the entries installed to OF-DPA tables,
per the OF-DPA spec.  See OF-DPA spec for full description of fields
in each flow and group table.  New table entries are pushed to the
device with ADD cmd.  Updated entries are pushed to the device with
MOD cmd.  For flow table entries, a crc32 key is made from fields of
the particular field.  For group table entries, the group_id is used
as the key.

The FDB table tracks fdb entries learned by the device or manually
pushed to the bridge by the user.  A crc32 key is made from the
port/mac/vlan tuple for the fdb entry.

The VLAN table tracks the ifindex-to-internal-vlan mapping for
untagged pkts.  On ingress, an untagged pkt is inserted with an
internal VLAN ID based on the input port's current internal VLAN ID.
The input port's internal VLAN will either be referenced by the port's
ifindex, if not bridged, or the containing bridge's ifindex, if
bridged.  Since the ifindex space isn't within a fixed range, uses a
hash table (with ifindex as key) to track internal VLAN ID for a given
ifindex.  The internal VLAN ID range is fixed and currently uses the
upper 255 VLAN IDs, starting at 0xf00.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces the first driver to benefit from the switchdev
infrastructure and to implement newly introduced switch ndos. This is a
driver for emulated switch chip implemented in qemu:
https://github.com/sfeldma/qemu-rocker/

This patch is a result of joint work with Scott Feldman.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To allow brport device to return current brport flags set on port.  Add
returned flags to nested IFLA_PROTINFO netlink msg built in dflt getlink.
With this change, netlink msg returned for bridge_getlink contains the port's
offloaded flag settings (the port's SELF settings).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current hwmode settings are "vepa" or "veb".  These are for NIC interfaces
with basic bridging function offloaded to HW.  Add new "swdev" for full
switch device offloads.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

This policy flag controls syncing of learned FDB entries to bridge's FDB.  If
on, FDB entries learned on bridge port device will be synced.  If off, device
may still learn new FDB entries but they will not be synced with bridge's FDB.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>

When the swdev device learns a new mac/vlan on a port, it sends some async
notification to the driver and the driver installs an FDB in the device.
To give a holistic system view, the learned mac/vlan should be reflected
in the bridge's FBD table, so the user, using normal iproute2 cmds, can view
what is currently learned by the device.  This API on the bridge driver gives
a way for the swdev driver to install an FBD entry in the bridge FBD table.
(And remove one).

This is equivalent to the device running these cmds:

  bridge fdb [add|del] <mac> dev <dev> vid <vlan id> master

This patch needs some extra eyeballs for review, in paricular around the
locking and contexts.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To notify switch driver of change in STP state of bridge port, add new
.ndo op and provide switchdev wrapper func to call ndo op. Use it in bridge
code then.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netdevice represents a port in a switch, it will expose
IFLA_PHYS_SWITCH_ID value via rtnl. Two netdevices with the same value
belong to one physical switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The goal of this is to provide a possibility to support various switch
chips. Drivers should implement relevant ndos to do so. Now there is
only one ndo defined:
- for getting physical switch id is in place.

Note that user can use random port netdevice to access the switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current name might seem that this actually offloads the fdb entry to
hw. So rename it to clearly present that this for hardware address
addition/removal.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 9c62a68d ("netpoll:
Remove dead packet receive code (CONFIG_NETPOLL_TRAP)") this
Kconfig option was removed.  So remove references to it from
all defconfigs as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver uses ip_out_local() and ip6_route_output() which are
defined only if CONFIG_INET and CONFIG_IPV6 are enabled respectively.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We do header check twice for a dodgy packet. One is done before
macvlan_start_xmit(), another is done before lower device's
ndo_start_xmit(). The first one seems redundant so this patch tries to
delay header check until a packet reaches its lower device (or macvtap)
through always enabling NETIF_F_GSO_ROBUST for macvlan device.

Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull irq fixes from Thomas Gleixner:
 "Three fixlets from the ARM SoC camp:
   - correct irqdomain initialization for atmel-aic
   - correct error handling for device tree parsing in bcm controllers"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: brcmstb-l2: Fix error handling of irq_of_parse_and_map
  irqchip: bcm7120-l2: Fix error handling of irq_of_parse_and_map
  irqchip: atmel-aic: Fix irqdomain initialization

Pull SCSI fixes from James Bottomley:
 "This is a set of ten fixes: 8 for UFS including four static checker
  warnings, a potential null deref in the voltage regulator code, a race
  on module unload, a ref counting fix on the well known LUNs which made
  it impossible to remove the ufs module and fix to correct the
  information in pwr_info.

  In addition to UFS, there's a blacklist for the Intel Multi-Flex array
  which chokes on report supported operation codes and a fix to an oops
  in bnx2fc caused by shared skbs"

[ For us non-SCSI people: "UFS" here is "Universal Flash Storage" not
  the filesystem.  - Linus ]

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  ufs: fix NULL dereference when no regulators are defined
  ufs: ensure clk gating work is finished before module unloading
  scsi: ufs: fix static checker warning in ufshcd_parse_clock_info
  scsi: ufs: fix static checker warning in __ufshcd_setup_clocks
  scsi: ufs: fix static checker warning in ufshcd_populate_vreg
  scsi: ufs: fix static checker errors in ufshcd_system_suspend
  ufs: fix power info after link start-up
  ufs: fix reference counting of W-LUs
  scsi: add Intel Multi-Flex to scsi scan blacklist
  bnx2fc: do not add shared skbs to the fcoe_rx_list

Pull staging/IIO driver fixes from Greg KH:
 "Here are some staging and IIO driver fixes for 3.18-rc7 that resolve a
  number of reported issues, and a new device id for a staging wireless
  driver.

  All of these have been in linux-next"

* tag 'staging-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8188eu: Add new device ID for DLink GO-USB-N150
  staging: r8188eu: Fix scheduling while atomic error introduced in commit fadbe0cd
  iio: accel: bmc150: set low default thresholds
  iio: accel: bmc150: Fix iio_event_spec direction
  iio: accel: bmc150: Send x, y and z motion separately
  iio: accel: bmc150: Error handling when mode set fails
  iio: gyro: bmg160: Fix iio_event_spec direction
  iio: gyro: bmg160: Send x, y and z motion separately
  iio: gyro: bmg160: Don't let interrupt mode to be open drain
  iio: gyro: bmg160: Error handling when mode set fails
  iio: adc: men_z188_adc: Add terminating entry for men_z188_ids
  iio: accel: kxcjk-1013: Fix kxcjk10013_set_range
  iio: Fix IIO_EVENT_CODE_EXTRACT_DIR bit mask

Pull tty/serial fix from Greg KH:
 "Here is a single revert for the of-serial driver that resolves a
  reported issue.

  This revert has been in linux-next for a while"

* tag 'tty-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "serial: of-serial: add PM suspend/resume support"

Pull USB fixes from Greg KH:
 "Here are some USB driver fixes and new device ids for 3.18-rc7.

  Full details are in the shortlog, and all of these have been in the
  linux-next tree for a while"

* tag 'usb-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb-quirks: Add reset-resume quirk for MS Wireless Laser Mouse 6000
  usb: xhci: rework root port wake bits if controller isn't allowed to wakeup
  USB: xhci: Reset a halted endpoint immediately when we encounter a stall.
  Revert "xhci: clear root port wake on bits if controller isn't wake-up capable"
  USB: xhci: don't start a halted endpoint before its new dequeue is set
  USB: uas: Add no-uas quirk for Hitachi usb-3 enclosures 4971:1012
  USB: ssu100: fix overrun-error reporting
  USB: keyspan: fix overrun-error reporting
  USB: keyspan: fix tty line-status reporting
  usb: serial: ftdi_sio: add PIDs for Matrix Orbital products
  usb: dwc3: ep0: fix for dead code
  USB: serial: cp210x: add IDs for CEL MeshConnect USB Stick

Pull thermal fixes from Eduardo Valentin:
 "In this -rc still very minor changes:

   - Lee Jones fixes compilation warning in sti thermal driver
   - Marjus Elfring removes unnecessary checks in exynos thermal driver
     (as per coccinelle)
   - Now we always update cpufreq policies, and thus get (hopefully)
     always in sync with cpufreq, thanks to Yadwinder"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: Exynos: Deletion of unnecessary checks before two function calls
  thermal: sti: Ignore suspend/resume functions when !PM_SLEEP
  thermal: cpu_cooling: Update always cpufreq policy with thermal constraints

Pull sound fixes from Takashi Iwai:
 "No excitement, here are only minor fixes: an endian fix for the new
  DSD format we added in 3.18, a fix for HP mute LED, and a fix for
  Native Instrument quirk"

* tag 'sound-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: pcm: Add big-endian DSD sample formats and fix XMOS DSD sample format
  ALSA: hda - One more HP machine needs to change mute led quirk
  ALSA: usb-audio: Use snd_usb_ctl_msg() for Native Instruments quirk

Pull ARM SoC fixes from Arnd Bergmann:
 "Not much interesting going on fixes-wise for us this week, as it
  should be for an -rc7.  I'm not expecting Olof to work much over
  Thanksgiving weekend, so I decided to take over again and push these
  out to you.

  Just four simple fixes this week:

   - one missing of_node_put() on armv7 based mvebu
   - forcing the USB host into the right mode on Chromebook
     (exynos5-snow)
   - enabling two important drivers for exynos_defconfig
   - fixing a noncritical bug for tegra that would cause a regression
     with common code patches queued for 3.19"

* tag 'armsoc-for-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: tegra: irq: fix buggy usage of irq_data irq field
  ARM: exynos_defconfig: Enable max77802 rtc and clock drivers
  ARM: dts: Explicitly set dr_mode on exynos5250-snow
  ARM: mvebu: add missing of_node_put() call in coherency.c

Pull ARM fixes from Russell King:
 "Another round of relatively small ARM fixes.

  Thomas spotted that the strex backoff delay bit was a disable bit, so
  it needed to be clear for this to work.  Vladimir spotted that using a
  restart block for the cache flush operation would return -EINTR, which
  userspace was not expecting.  Dmitry spotted that the auxiliary
  control register accesses for Xscale were not correct"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8226/1: cacheflush: get rid of restarting block
  ARM: 8222/1: mvebu: enable strex backoff delay
  ARM: 8216/1: xscale: correct auxiliary register in suspend/resume