Re-reading a recently merged fix to the raw_gadget driver showed that
it inadvertently introduced a double-free bug in a failure pathway.
If raw_ioctl_init() encounters an error after the driver ID number has
been allocated, it deallocates the ID number before returning.  But
when dev_free() runs later on, it will then try to deallocate the ID
number a second time.

Closely related to this issue is another error in the recent fix: The
ID number is stored in the raw_dev structure before the code checks to
see whether the structure has already been initialized, in which case
the new ID number would overwrite the earlier value.

The solution to both bugs is to keep the new ID number in a local
variable, and store it in the raw_dev structure only after the check
for prior initialization.  No errors can occur after that point, so
the double-free will never happen.

Fixes: f2d8c260 ("usb: gadget: Fix non-unique driver names in raw-gadget driver")
CC: Andrey Konovalov <andreyknvl@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YrMrRw5AyIZghN0v@rowland.harvard.eduSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Meteor Lake TCSS(Type-C Subsystem) xHCI needs to be runtime suspended
whenever possible to allow the TCSS hardware block to enter D3cold and
thus save energy.

Cc: stable@kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-5-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the same way as Intel Alder Lake TCSS (Type-C Subsystem) the Raptor
Lake TCSS xHCI needs to be runtime suspended whenever possible to
allow the TCSS hardware block to enter D3cold and thus save energy.

Cc: stable@kernel.org
Signed-off-by: Tanveer Alam <tanveer1.alam@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-4-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.

During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.

Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.

[tidy up old code while moving it, reword header -Mathias]

Cc: stable@kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-5.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for 5.19-rc4

Here are some new modem device ids and support for further PL2303
device types.

All but the final commit (RM500K device id) have been in linux-next and
with no reported issues.

* tag 'usb-serial-5.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: option: add Quectel RM500K module support
  USB: serial: option: add Quectel EM05-G modem
  USB: serial: pl2303: add support for more HXN (G) types
  USB: serial: option: add Telit LE910Cx 0x1250 composition

Add usb product id of the Quectel RM500K module.

RM500K provides 2 mandatory interfaces to Linux host after enumeration.
 - /dev/ttyUSB5: this is a serial interface for control path. User needs
   to write AT commands to this device node to query status, set APN,
   set PIN code, and enable/disable the data connection to 5G network.
 - ethX: this is the data path provided as a RNDIS devices. After the
   data connection has been established, Linux host can access 5G data
   network via this interface.

"RNDIS": RNDIS + ADB + AT (/dev/ttyUSB5) + MODEM COMs

usb-devices output for 0x7001:
T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=7001 Rev=00.01
S:  Manufacturer=MediaTek Inc.
S:  Product=USB DATA CARD
S:  SerialNumber=869206050009672
C:  #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Co-developed-by: Ballon Shi <ballon.shi@quectel.com>
Signed-off-by: Ballon Shi <ballon.shi@quectel.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>

The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:

"RMNET"	: AT + DIAG + NMEA + Modem + QMI
"MBIM"	: MBIM + AT + DIAG + NMEA + Modem

The detailed description of the USB configuration for each mode as follows:

RMNET Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=030a Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

MBIM Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=030a Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Yonglin Tan <yonglin.tan@outlook.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>

Add support for further HXN (G) type devices (GT variant, GL variant, GS
variant and GR) and document the bcdDevice mapping.

Note that the TA and TB types use the same bcdDevice as some GT and GE
variants, respectively, but that the HX status request can be used to
determine which is which.

Also note that we currently do not distinguish between the various HXN
(G) types in the driver but that this may change eventually (e.g. when
adding GPIO support).
Reported-by: Charles Yeh <charlesyeh522@gmail.com>
Link: https://lore.kernel.org/r/YrF77b9DdeumUAee@hovoldconsulting.com
Cc: stable@vger.kernel.org	# 5.13
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Intel SoC PMIC is a generic name for all PMICs that are used
on Intel platforms. In particular, INTEL_SOC_PMIC kernel configuration
option refers to Crystal Cove PMIC, which has never been a part
of any Intel Broxton hardware. Drop wrong dependency from Kconfig.

Note, the correct dependency is satisfied via ACPI PMIC OpRegion driver,
which the Type-C depends on.

Fixes: d2061f9c ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220620104316.57592-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A panic can occur if the endpoint becomes disabled and the
uvcg_video_pump adds the request back to the req_free list after it has
already been queued to the endpoint. The endpoint complete will add the
request back to the req_free list. Invalidate the local request handle
once it's been queued.

<6>[  246.796704][T13726] configfs-gadget gadget: uvc: uvc_function_set_alt(1, 0)
<3>[  246.797078][   T26] list_add double add: new=ffffff878bee5c40, prev=ffffff878bee5c40, next=ffffff878b0f0a90.
<6>[  246.797213][   T26] ------------[ cut here ]------------
<2>[  246.797224][   T26] kernel BUG at lib/list_debug.c:31!
<6>[  246.807073][   T26] Call trace:
<6>[  246.807180][   T26]  uvcg_video_pump+0x364/0x38c
<6>[  246.807366][   T26]  process_one_work+0x2a4/0x544
<6>[  246.807394][   T26]  worker_thread+0x350/0x784
<6>[  246.807442][   T26]  kthread+0x2ac/0x320

Fixes: f9897ec0 ("usb: gadget: uvc: only pump video data if necessary")
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20220617163154.16621-1-w36195@motorola.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

"make dtbs_check":

    arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee080100: phys: [[17, 0], [31]] is too long
	    From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml
    arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee0c0100: phys: [[17, 1], [33], [21, 0]] is too long
	    From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml

Some USB EHCI controllers (e.g. on the Renesas RZ/G1C SoC) have multiple
PHYs.  Increase the maximum number of PHYs to 3, which is sufficient for
now.

Fixes: 0499220d ("dt-bindings: Add missing array size constraints")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c5d19e2f9714f43effd90208798fc1936098078f.1655301043.git.geert+renesas@glider.beSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

"make dtbs_check":

    arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee080000: phys: [[17, 0], [31]] is too long
	    From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
    arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee0c0000: phys: [[17, 1], [33], [21, 0]] is too long
	    From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml

Some USB OHCI controllers (e.g. on the Renesas RZ/G1C SoC) have multiple
PHYs.  Increase the maximum number of PHYs to 3, which is sufficient for
now.

Fixes: 0499220d ("dt-bindings: Add missing array size constraints")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/0112f9c8881513cb33bf7b66bc743dd08b35a2f5.1655301203.git.geert+renesas@glider.beSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In a report for a separate bug (which has already been fixed by commit
5f0b5f4d "usb: gadget: fix race when gadget driver register via
ioctl") in the raw-gadget driver, the syzbot console log included
error messages caused by attempted registration of a new driver with
the same name as an existing driver:

> kobject_add_internal failed for raw-gadget with -EEXIST, don't try to register things with the same name in the same directory.
> UDC core: USB Raw Gadget: driver registration failed: -17
> misc raw-gadget: fail, usb_gadget_register_driver returned -17

These errors arise because raw_gadget.c registers a separate UDC
driver for each of the UDC instances it creates, but these drivers all
have the same name: "raw-gadget".  Until recently this wasn't a
problem, but when the "gadget" bus was added and UDC drivers were
registered on this bus, it became possible for name conflicts to cause
the registrations to fail.  The reason is simply that the bus code in
the driver core uses the driver name as a sysfs directory name (e.g.,
/sys/bus/gadget/drivers/raw-gadget/), and you can't create two
directories with the same pathname.

To fix this problem, the driver names used by raw-gadget are made
distinct by appending a unique ID number: "raw-gadget.N", with a
different value of N for each driver instance.  And to avoid the
proliferation of error handling code in the raw_ioctl_init() routine,
the error return paths are refactored into the common pattern (goto
statements leading to cleanup code at the end of the routine).

Link: https://lore.kernel.org/all/0000000000008c664105dffae2eb@google.com/
Fixes: fc274c1e "USB: gadget: Add a new bus for gadgets"
CC: Andrey Konovalov <andreyknvl@gmail.com>
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+02b16343704b3af1667e@syzkaller.appspotmail.com
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Acked-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YqdG32w+3h8c1s7z@rowland.harvard.eduSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Maintainers of the directory Documentation/devicetree/bindings/usb
are also the maintainers of the corresponding directory
include/dt-bindings/usb.

Add the file entry for include/dt-bindings/usb to the appropriate
section in MAINTAINERS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220613124647.32019-1-lukas.bulwahn@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for the following Telit LE910Cx composition:

0x1250: rmnet, tty, tty, tty, tty
Reviewed-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Carlo Lobrano <c.lobrano@gmail.com>
Link: https://lore.kernel.org/r/20220614075623.2392607-1-c.lobrano@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>

Pull x86 fixes from Thomas Gleixner:

 - Make RESERVE_BRK() work again with older binutils. The recent
   'simplification' broke that.

 - Make early #VE handling increment RIP when successful.

 - Make the #VE code consistent vs. the RIP adjustments and add
   comments.

 - Handle load_unaligned_zeropad() across page boundaries correctly in
   #VE when the second page is shared.

* tag 'x86-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tdx: Handle load_unaligned_zeropad() page-cross to a shared page
  x86/tdx: Clarify RIP adjustments in #VE handler
  x86/tdx: Fix early #VE handling
  x86/mm: Fix RESERVE_BRK() for older binutils

Pull build tooling updates from Thomas Gleixner:

 - Remove obsolete CONFIG_X86_SMAP reference from objtool

 - Fix overlapping text section failures in faddr2line for real

 - Remove OBJECT_FILES_NON_STANDARD usage from x86 ftrace and replace it
   with finegrained annotations so objtool can validate that code
   correctly.

* tag 'objtool-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ftrace: Remove OBJECT_FILES_NON_STANDARD usage
  faddr2line: Fix overlapping text section failures, the sequel
  objtool: Fix obsolete reference to CONFIG_X86_SMAP

Pull scheduler fix from Thomas Gleixner:
 "A single scheduler fix plugging a race between sched_setscheduler()
  and balance_push().

  sched_setscheduler() spliced the balance callbacks accross a lock
  break which makes it possible for an interleaving schedule() to
  observe an empty list"

* tag 'sched-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix balance_push() vs __sched_setscheduler()

Pull lockdep fix from Thomas Gleixner:
 "A RT fix for lockdep.

  lockdep invokes prandom_u32() to create cookies. This worked until
  prandom_u32() was switched to the real random generator, which takes a
  spinlock for extraction, which does not work on RT when invoked from
  atomic contexts.

  lockdep has no requirement for real random numbers and it turns out
  sched_clock() is good enough to create the cookie. That works
  everywhere and is faster"

* tag 'locking-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/lockdep: Use sched_clock() for random numbers

Pull irq fixes from Thomas Gleixner:
 "A set of interrupt subsystem updates:

  Core:

   - Ensure runtime power management for chained interrupts

  Drivers:

   - A collection of OF node refcount fixes

   - Unbreak MIPS uniprocessor builds

   - Fix xilinx interrupt controller Kconfig dependencies

   - Add a missing compatible string to the Uniphier driver"

* tag 'irq-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/loongson-liointc: Use architecture register to get coreid
  irqchip/uniphier-aidet: Add compatible string for NX1 SoC
  dt-bindings: interrupt-controller/uniphier-aidet: Add bindings for NX1 SoC
  irqchip/realtek-rtl: Fix refcount leak in map_interrupts
  irqchip/gic-v3: Fix refcount leak in gic_populate_ppi_partitions
  irqchip/gic-v3: Fix error handling in gic_populate_ppi_partitions
  irqchip/apple-aic: Fix refcount leak in aic_of_ic_init
  irqchip/apple-aic: Fix refcount leak in build_fiq_affinity
  irqchip/gic/realview: Fix refcount leak in realview_gic_of_init
  irqchip/xilinx: Remove microblaze+zynq dependency
  genirq: PM: Use runtime PM for chained interrupts

Merge tag 'char-misc-5.19-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc driver fixes for real from Greg KH:
 "Let's tag the proper branch this time...

  Here are some small char/misc driver fixes for 5.19-rc3 that resolve
  some reported issues.

  They include:

   - mei driver fixes

   - comedi driver fix

   - rtsx build warning fix

   - fsl-mc-bus driver fix

  All of these have been in linux-next for a while with no reported
  issues"

This is what the merge in commit f0ec9c65 _should_ have merged, but
Greg fat-fingered the pull request and I got some small changes from
linux-next instead there. Credit to Nathan Chancellor for eagle-eyes.

Link: https://lore.kernel.org/all/Yqywy+Md2AfGDu8v@dev-arch.thelio-3990X/

* tag 'char-misc-5.19-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  bus: fsl-mc-bus: fix KASAN use-after-free in fsl_mc_bus_remove()
  mei: me: add raptor lake point S DID
  mei: hbm: drop capability response on early shutdown
  mei: me: set internal pg flag to off on hardware reset
  misc: rtsx: Fix clang -Wsometimes-uninitialized in rts5261_init_from_hw()
  comedi: vmk80xx: fix expression for tx buffer size

Pull i2c fixes from Wolfram Sang:
 "MAINTAINERS rectifications and a few minor driver fixes"

* tag 'i2c-for-5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mediatek: Fix an error handling path in mtk_i2c_probe()
  i2c: designware: Use standard optional ref clock implementation
  MAINTAINERS: core DT include belongs to core
  MAINTAINERS: add include/dt-bindings/i2c to I2C SUBSYSTEM HOST DRIVERS
  i2c: npcm7xx: Add check for platform_driver_register
  MAINTAINERS: Update Synopsys DesignWare I2C to Supported

Pull xfs fixes from Darrick Wong:
 "There's not a whole lot this time around (I'm still on vacation) but
  here are some important fixes for new features merged in -rc1:

   - Fix a bug where inode flag changes would accidentally drop nrext64

   - Fix a race condition when toggling LARP mode"

* tag 'xfs-5.19-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: preserve DIFLAG2_NREXT64 when setting other inode attributes
  xfs: fix variable state usage
  xfs: fix TOCTOU race involving the new logged xattrs control knob

Pull ext4 fixes from Ted Ts'o:
 "Fix a variety of bugs, many of which were found by folks using fuzzing
  or error injection.

  Also fix up how test_dummy_encryption mount option is handled for the
  new mount API.

  Finally, fix/cleanup a number of comments and ext4 Documentation
  files"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix a doubled word "need" in a comment
  ext4: add reserved GDT blocks check
  ext4: make variable "count" signed
  ext4: correct the judgment of BUG in ext4_mb_normalize_request
  ext4: fix bug_on ext4_mb_use_inode_pa
  ext4: fix up test_dummy_encryption handling for new mount API
  ext4: use kmemdup() to replace kmalloc + memcpy
  ext4: fix super block checksum incorrect after mount
  ext4: improve write performance with disabled delalloc
  ext4: fix warning when submitting superblock in ext4_commit_super()
  ext4, doc: remove unnecessary escaping
  ext4: fix incorrect comment in ext4_bio_write_page()
  fs: fix jbd2_journal_try_to_free_buffers() kernel-doc comment

Pull cifs client fixes from Steve French:
 "Two cifs debugging improvements - one found to deal with debugging a
  multichannel problem and one for a recent fallocate issue

  This does include the two larger multichannel reconnect (dynamically
  adjusting interfaces on reconnect) patches, because we recently found
  an additional problem with multichannel to one server type that I want
  to include at the same time"

* tag '5.19-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: when a channel is not found for server, log its connection id
  smb3: add trace point for SMB2_set_eof

Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Link: https://lore.kernel.org/r/20220605091503.12513-1-wangxiang@cdjrlc.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

We capture a NULL pointer issue when resizing a corrupt ext4 image which
is freshly clear resize_inode feature (not run e2fsck). It could be
simply reproduced by following steps. The problem is because of the
resize_inode feature was cleared, and it will convert the filesystem to
meta_bg mode in ext4_resize_fs(), but the es->s_reserved_gdt_blocks was
not reduced to zero, so could we mistakenly call reserve_backup_gdb()
and passing an uninitialized resize_inode to it when adding new group
descriptors.

 mkfs.ext4 /dev/sda 3G
 tune2fs -O ^resize_inode /dev/sda #forget to run requested e2fsck
 mount /dev/sda /mnt
 resize2fs /dev/sda 8G

 ========
 BUG: kernel NULL pointer dereference, address: 0000000000000028
 CPU: 19 PID: 3243 Comm: resize2fs Not tainted 5.18.0-rc7-00001-gfde086c5ebfd #748
 ...
 RIP: 0010:ext4_flex_group_add+0xe08/0x2570
 ...
 Call Trace:
  <TASK>
  ext4_resize_fs+0xbec/0x1660
  __ext4_ioctl+0x1749/0x24e0
  ext4_ioctl+0x12/0x20
  __x64_sys_ioctl+0xa6/0x110
  do_syscall_64+0x3b/0x90
  entry_SYSCALL_64_after_hwframe+0x44/0xae
 RIP: 0033:0x7f2dd739617b
 ========

The fix is simple, add a check in ext4_resize_begin() to make sure that
the es->s_reserved_gdt_blocks is zero when the resize_inode feature is
disabled.

Cc: stable@kernel.org
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20220601092717.763694-1-yi.zhang@huawei.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

Since dx_make_map() may return -EFSCORRUPTED now, so change "count" to
be a signed integer so we can correctly check for an error code returned
by dx_make_map().

Fixes: 46c116b9 ("ext4: verify dir block before splitting it")
Cc: stable@kernel.org
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20220530100047.537598-1-dingxiang@cmss.chinamobile.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

ext4_mb_normalize_request() can move logical start of allocated blocks
to reduce fragmentation and better utilize preallocation. However logical
block requested as a start of allocation (ac->ac_o_ex.fe_logical) should
always be covered by allocated blocks so we should check that by
modifying and to or in the assertion.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20220528110017.354175-3-libaokun1@huawei.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

Hulk Robot reported a BUG_ON:
==================================================================
kernel BUG at fs/ext4/mballoc.c:3211!
[...]
RIP: 0010:ext4_mb_mark_diskspace_used.cold+0x85/0x136f
[...]
Call Trace:
 ext4_mb_new_blocks+0x9df/0x5d30
 ext4_ext_map_blocks+0x1803/0x4d80
 ext4_map_blocks+0x3a4/0x1a10
 ext4_writepages+0x126d/0x2c30
 do_writepages+0x7f/0x1b0
 __filemap_fdatawrite_range+0x285/0x3b0
 file_write_and_wait_range+0xb1/0x140
 ext4_sync_file+0x1aa/0xca0
 vfs_fsync_range+0xfb/0x260
 do_fsync+0x48/0xa0
[...]
==================================================================

Above issue may happen as follows:
-------------------------------------
do_fsync
 vfs_fsync_range
  ext4_sync_file
   file_write_and_wait_range
    __filemap_fdatawrite_range
     do_writepages
      ext4_writepages
       mpage_map_and_submit_extent
        mpage_map_one_extent
         ext4_map_blocks
          ext4_mb_new_blocks
           ext4_mb_normalize_request
            >>> start + size <= ac->ac_o_ex.fe_logical
           ext4_mb_regular_allocator
            ext4_mb_simple_scan_group
             ext4_mb_use_best_found
              ext4_mb_new_preallocation
               ext4_mb_new_inode_pa
                ext4_mb_use_inode_pa
                 >>> set ac->ac_b_ex.fe_len <= 0
           ext4_mb_mark_diskspace_used
            >>> BUG_ON(ac->ac_b_ex.fe_len <= 0);

we can easily reproduce this problem with the following commands:
	`fallocate -l100M disk`
	`mkfs.ext4 -b 1024 -g 256 disk`
	`mount disk /mnt`
	`fsstress -d /mnt -l 0 -n 1000 -p 1`

The size must be smaller than or equal to EXT4_BLOCKS_PER_GROUP.
Therefore, "start + size <= ac->ac_o_ex.fe_logical" may occur
when the size is truncated. So start should be the start position of
the group where ac_o_ex.fe_logical is located after alignment.
In addition, when the value of fe_logical or EXT4_BLOCKS_PER_GROUP
is very large, the value calculated by start_off is more accurate.

Cc: stable@kernel.org
Fixes: cd648b8a ("ext4: trim allocation requests to group size")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20220528110017.354175-2-libaokun1@huawei.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

Since ext4 was converted to the new mount API, the test_dummy_encryption
mount option isn't being handled entirely correctly, because the needed
fscrypt_set_test_dummy_encryption() helper function combines
parsing/checking/applying into one function.  That doesn't work well
with the new mount API, which split these into separate steps.

This was sort of okay anyway, due to the parsing logic that was copied
from fscrypt_set_test_dummy_encryption() into ext4_parse_param(),
combined with an additional check in ext4_check_test_dummy_encryption().
However, these overlooked the case of changing the value of
test_dummy_encryption on remount, which isn't allowed but ext4 wasn't
detecting until ext4_apply_options() when it's too late to fail.
Another bug is that if test_dummy_encryption was specified multiple
times with an argument, memory was leaked.

Fix this up properly by using the new helper functions that allow
splitting up the parse/check/apply steps for test_dummy_encryption.

Fixes: cebe85d5 ("ext4: switch to the new mount api")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20220526040412.173025-1-ebiggers@kernel.orgSigned-off-by: Theodore Ts'o <tytso@mit.edu>

Replace kmalloc + memcpy with kmemdup()
Signed-off-by: Shuqi Zhang <zhangshuqi3@huawei.com>
Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20220525030120.803330-1-zhangshuqi3@huawei.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

We got issue as follows:
[home]# mount  /dev/sda  test
EXT4-fs (sda): warning: mounting fs with errors, running e2fsck is recommended
[home]# dmesg
EXT4-fs (sda): warning: mounting fs with errors, running e2fsck is recommended
EXT4-fs (sda): Errors on filesystem, clearing orphan list.
EXT4-fs (sda): recovery complete
EXT4-fs (sda): mounted filesystem with ordered data mode. Quota mode: none.
[home]# debugfs /dev/sda
debugfs 1.46.5 (30-Dec-2021)
Checksum errors in superblock!  Retrying...

Reason is ext4_orphan_cleanup will reset ‘s_last_orphan’ but not update
super block checksum.

To solve above issue, defer update super block checksum after
ext4_orphan_cleanup.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Cc: stable@kernel.org
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20220525012904.1604737-1-yebin10@huawei.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

cifs_ses_get_chan_index gets the index for a given server pointer.
When a match is not found, we warn about a possible bug.
However, printing details about the non-matching server could be
more useful to debug here.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>

load_unaligned_zeropad() can lead to unwanted loads across page boundaries.
The unwanted loads are typically harmless. But, they might be made to
totally unrelated or even unmapped memory. load_unaligned_zeropad()
relies on exception fixup (#PF, #GP and now #VE) to recover from these
unwanted loads.

In TDX guests, the second page can be shared page and a VMM may configure
it to trigger #VE.

The kernel assumes that #VE on a shared page is an MMIO access and tries to
decode instruction to handle it. In case of load_unaligned_zeropad() it
may result in confusion as it is not MMIO access.

Fix it by detecting split page MMIO accesses and failing them.
load_unaligned_zeropad() will recover using exception fixups.

The issue was discovered by analysis and reproduced artificially. It was
not triggered during testing.

[ dhansen: fix up changelogs and comments for grammar and clarity,
	   plus incorporate Kirill's off-by-one fix]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220614120135.14812-4-kirill.shutemov@linux.intel.com

Pull NFS client fixes from Anna Schumaker:

 - Add FMODE_CAN_ODIRECT support to NFSv4 so opens don't fail

 - Fix trunking detection & cl_max_connect setting

 - Avoid pnfs_update_layout() livelocks

 - Don't keep retrying pNFS if the server replies with NFS4ERR_UNAVAILABLE

* tag 'nfs-for-5.19-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFSv4: Add FMODE_CAN_ODIRECT after successful open of a NFS4.x file
  sunrpc: set cl_max_connect when cloning an rpc_clnt
  pNFS: Avoid a live lock condition in pnfs_update_layout()
  pNFS: Don't keep retrying if the server replied NFS4ERR_LAYOUTUNAVAILABLE

Pull pci fix from Bjorn Helgaas:
 "Revert clipping of PCI host bridge windows to avoid E820 regions,
  which broke several machines by forcing unnecessary BAR reassignments
  (Hans de Goede)"

* tag 'pci-v5.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  x86/PCI: Revert "x86/PCI: Clip only host bridge windows for E820 regions"

Pull printk fixes from Petr Mladek:
 "Make the global console_sem available for CPU that is handling panic()
  or shutdown.

  This is an old problem when an existing console lock owner might block
  console output, but it became more visible with the kthreads"

* tag 'printk-for-5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
  printk: Wait for the global console lock when the system is going down
  printk: Block console kthreads when direct printing will be required