Skip to content

L
linux
Switch branch/tag
  1. 23 Sep, 2015 13 commits
    • Karicheri, Muralidharan's avatar
      net: netcp: check for interface handle in netcp_module_probe() · 915c5857
      Karicheri, Muralidharan authored 
      Currently netcp_module_probe() doesn't check the return value of
of_parse_phandle() that points to the interface data for the
module and then pass the node ptr to the module which is incorrect.
Check for return value and free the intf_modpriv if there is error.
Signed-off-by: default avatarMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      915c5857
    • Karicheri, Muralidharan's avatar
      net: netcp: add error check to netcp_allocate_rx_buf() · e558b1fb
      Karicheri, Muralidharan authored 
      Currently, if netcp_allocate_rx_buf() fails due no descriptors
in the rx free descriptor queue, inside the netcp_rxpool_refill() function
the iterative loop to fill buffers doesn't terminate right away. So modify
the netcp_allocate_rx_buf() to return an error code and use it break the
loop when there is error.
Signed-off-by: default avatarMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e558b1fb
    • Karicheri, Muralidharan's avatar
      net: netcp: move netcp_register_interface() to after attach module · 736532a0
      Karicheri, Muralidharan authored 
      The netcp interface is not fully initialized before attach the module
to the interface. For example, the tx pipe/rx pipe is initialized
in ethss module as part of attach(). So until this is complete, the
interface can't be registered.  So move registration of interface to
net device outside the current loop that attaches the modules to the
interface.
Signed-off-by: default avatarMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      736532a0
    • Karicheri, Muralidharan's avatar
      net: netcp: remove dead code from the driver · 156e3c21
      Karicheri, Muralidharan authored 
      netcp_core is the first driver that will get initialized and the modules
(ethss, pa etc) will then get initialized. So the code at the end of
netcp_probe() that iterate over the modules is a dead code as the module
list will be always be empty. So remove this code.
Signed-off-by: default avatarMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      156e3c21
    • WingMan Kwok's avatar
      net: netcp: ethss: fix error in calling sgmii api with incorrect offset · 8c85151d
      WingMan Kwok authored 
      On K2HK, sgmii module registers of slave 0 and 1 are mem
mapped to one contiguous block, while those of slave 2
and 3 are mapped to another contiguous block.  However,
on K2E and K2L, sgmii module registers of all slaves are
mem mapped to one contiguous block.  SGMII APIs expect
slave 0 sgmii base when API is invoked for slave 0 and 1,
and slave 2 sgmii base when invoked for other slaves.
Before this patch, slave 0 sgmii base is always passed to
sgmii API for K2E regardless which slave is the API invoked
for.  This patch fixes the problem.
Signed-off-by: default avatarWingMan Kwok <w-kwok2@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      8c85151d
    • David Woodhouse's avatar
      Fix AF_PACKET ABI breakage in 4.2 · d3869efe
      David Woodhouse authored 
      Commit 7d824109 ("virtio: add explicit big-endian support to memory
accessors") accidentally changed the virtio_net header used by
AF_PACKET with PACKET_VNET_HDR from host-endian to big-endian.

Since virtio_legacy_is_little_endian() is a very long identifier,
define a vio_le macro and use that throughout the code instead of the
hard-coded 'false' for little-endian.

This restores the ABI to match 4.1 and earlier kernels, and makes my
test program work again.
Signed-off-by: default avatarDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d3869efe
    • Neil Horman's avatar
      netpoll: Close race condition between poll_one_napi and napi_disable · 2d8bff12
      Neil Horman authored 
      Drivers might call napi_disable while not holding the napi instance poll_lock.
In those instances, its possible for a race condition to exist between
poll_one_napi and napi_disable.  That is to say, poll_one_napi only tests the
NAPI_STATE_SCHED bit to see if there is work to do during a poll, and as such
the following may happen:

CPU0				CPU1
ndo_tx_timeout			napi_poll_dev
 napi_disable			 poll_one_napi
  test_and_set_bit (ret 0)
				  test_bit (ret 1)
   reset adapter		   napi_poll_routine

If the adapter gets a tx timeout without a napi instance scheduled, its possible
for the adapter to think it has exclusive access to the hardware  (as the napi
instance is now scheduled via the napi_disable call), while the netpoll code
thinks there is simply work to do.  The result is parallel hardware access
leading to corrupt data structures in the driver, and a crash.

Additionaly, there is another, more critical race between netpoll and
napi_disable.  The disabled napi state is actually identical to the scheduled
state for a given napi instance.  The implication being that, if a napi instance
is disabled, a netconsole instance would see the napi state of the device as
having been scheduled, and poll it, likely while the driver was dong something
requiring exclusive access.  In the case above, its fairly clear that not having
the rings in a state ready to be polled will cause any number of crashes.

The fix should be pretty easy.  netpoll uses its own bit to indicate that that
the napi instance is in a state of being serviced by netpoll (NAPI_STATE_NPSVC).
We can just gate disabling on that bit as well as the sched bit.  That should
prevent netpoll from conducting a napi poll if we convert its set bit to a
test_and_set_bit operation to provide mutual exclusion

Change notes:
V2)
	Remove a trailing whtiespace
	Resubmit with proper subject prefix

V3)
	Clean up spacing nits
Signed-off-by: default avatarNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: jmaxwell@redhat.com
Tested-by: jmaxwell@redhat.com
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2d8bff12
    • Eric Dumazet's avatar
      tcp: add proper TS val into RST packets · 675ee231
      Eric Dumazet authored 
      RST packets sent on behalf of TCP connections with TS option (RFC 7323
TCP timestamps) have incorrect TS val (set to 0), but correct TS ecr.

A > B: Flags [S], seq 0, win 65535, options [mss 1000,nop,nop,TS val 100
ecr 0], length 0
B > A: Flags [S.], seq 2444755794, ack 1, win 28960, options [mss
1460,nop,nop,TS val 7264344 ecr 100], length 0
A > B: Flags [.], ack 1, win 65535, options [nop,nop,TS val 110 ecr
7264344], length 0

B > A: Flags [R.], seq 1, ack 1, win 28960, options [nop,nop,TS val 0
ecr 110], length 0

We need to call skb_mstamp_get() to get proper TS val,
derived from skb->skb_mstamp

Note that RFC 1323 was advocating to not send TS option in RST segment,
but RFC 7323 recommends the opposite :

  Once TSopt has been successfully negotiated, that is both <SYN> and
  <SYN,ACK> contain TSopt, the TSopt MUST be sent in every non-<RST>
  segment for the duration of the connection, and SHOULD be sent in an
  <RST> segment (see Section 5.2 for details)

Note this RFC recommends to send TS val = 0, but we believe it is
premature : We do not know if all TCP stacks are properly
handling the receive side :

   When an <RST> segment is
   received, it MUST NOT be subjected to the PAWS check by verifying an
   acceptable value in SEG.TSval, and information from the Timestamps
   option MUST NOT be used to update connection state information.
   SEG.TSecr MAY be used to provide stricter <RST> acceptance checks.

In 5 years, if/when all TCP stack are RFC 7323 ready, we might consider
to decide to send TS val = 0, if it buys something.

Fixes: 7faee5c0 ("tcp: remove TCP_SKB_CB(skb)->when")
Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
Acked-by: default avatarYuchung Cheng <ycheng@google.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      675ee231
    • Neil Armstrong's avatar
      net: dsa: Fix Marvell Egress Trailer check · fbd03513
      Neil Armstrong authored 
      The Marvell Egress rx trailer check must be fixed to
correctly detect bad bits in the third byte of the
Eggress trailer as described in the Table 28 of the
88E6060 datasheet.
The current code incorrectly omits to check the third
byte and checks the fourth byte twice.
Signed-off-by: default avatarNeil Armstrong <narmstrong@baylibre.com>
Acked-by: default avatarGuenter Roeck <linux@roeck-us.net>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      fbd03513
    • Dmitriy Vyukov's avatar
      lib: fix data race in rhashtable_rehash_one · 7def0f95
      Dmitriy Vyukov authored 
      rhashtable_rehash_one() uses complex logic to update entry->next field,
after INIT_RHT_NULLS_HEAD and NULLS_MARKER expansion:

entry->next = 1 | ((base + off) << 1)

This can be compiled along the lines of:

entry->next = base + off
entry->next <<= 1
entry->next |= 1

Which will break concurrent readers.

NULLS value recomputation is not needed here, so just remove
the complex logic.

The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: default avatarDmitry Vyukov <dvyukov@google.com>
Acked-by: default avatarEric Dumazet <edumazet@google.com>
Acked-by: default avatarThomas Graf <tgraf@suug.ch>
Acked-by: default avatarHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      7def0f95
    • Tobias Klauser's avatar
      ch9200: Convert to use module_usb_driver · 23eedbc2
      Tobias Klauser authored 
      Converts the ch9200 driver to use the module_usb_driver() macro which
makes the code smaller and a bit simpler.
Signed-off-by: default avatarTobias Klauser <tklauser@distanz.ch>
Acked-by: default avatarMatthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      23eedbc2
    • Jesse Gross's avatar
      openvswitch: Zero flows on allocation. · ae5f2fb1
      Jesse Gross authored 
      When support for megaflows was introduced, OVS needed to start
installing flows with a mask applied to them. Since masking is an
expensive operation, OVS also had an optimization that would only
take the parts of the flow keys that were covered by a non-zero
mask. The values stored in the remaining pieces should not matter
because they are masked out.

While this works fine for the purposes of matching (which must always
look at the mask), serialization to netlink can be problematic. Since
the flow and the mask are serialized separately, the uninitialized
portions of the flow can be encoded with whatever values happen to be
present.

In terms of functionality, this has little effect since these fields
will be masked out by definition. However, it leaks kernel memory to
userspace, which is a potential security vulnerability. It is also
possible that other code paths could look at the masked key and get
uninitialized data, although this does not currently appear to be an
issue in practice.

This removes the mask optimization for flows that are being installed.
This was always intended to be the case as the mask optimizations were
really targetting per-packet flow operations.

Fixes: 03f0d916 ("openvswitch: Mega flow implementation")
Signed-off-by: default avatarJesse Gross <jesse@nicira.com>
Acked-by: default avatarPravin B Shelar <pshelar@nicira.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ae5f2fb1
    • Russell King's avatar
      net: dsa: actually force the speed on the CPU port · 53adc9e8
      Russell King authored 
      Commit 54d792f2 ("net: dsa: Centralise global and port setup
code into mv88e6xxx.") merged in the 4.2 merge window broke the link
speed forcing for the CPU port of Marvell DSA switches.  The original
code was:

        /* MAC Forcing register: don't force link, speed, duplex
         * or flow control state to any particular values on physical
         * ports, but force the CPU port and all DSA ports to 1000 Mb/s
         * full duplex.
         */
        if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
                REG_WRITE(addr, 0x01, 0x003e);
        else
                REG_WRITE(addr, 0x01, 0x0003);

but the new code does a read-modify-write:

                reg = _mv88e6xxx_reg_read(ds, REG_PORT(port), PORT_PCS_CTRL);
                if (dsa_is_cpu_port(ds, port) ||
                    ds->dsa_port_mask & (1 << port)) {
                        reg |= PORT_PCS_CTRL_FORCE_LINK |
                                PORT_PCS_CTRL_LINK_UP |
                                PORT_PCS_CTRL_DUPLEX_FULL |
                                PORT_PCS_CTRL_FORCE_DUPLEX;
                        if (mv88e6xxx_6065_family(ds))
                                reg |= PORT_PCS_CTRL_100;
                        else
                                reg |= PORT_PCS_CTRL_1000;

The link speed in the PCS control register is a two bit field.  Forcing
the link speed in this way doesn't ensure that the bit field is set to
the correct value - on the hardware I have here, the speed bitfield
remains set to 0x03, resulting in the speed not being forced to gigabit.

We must clear both bits before forcing the link speed.

Fixes: 54d792f2 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: default avatarRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      53adc9e8
  3. 22 Sep, 2015 1 commit
  5. 21 Sep, 2015 25 commits
  7. 18 Sep, 2015 1 commit
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7