- 11 Jun, 2013 1 commit
-
-
Andrew Lunn authored
Enable the second PCIe port on QNAP TS-11x/TS-21x devices as newer revisions (rev 1.3) have a USB 3.0 chip from Etron on PCIe port 1. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Jason Cooper <jason@lakedaemon.net>
-
- 08 Jun, 2013 1 commit
-
-
Ezequiel Garcia authored
These properties are not needed so it's safe to remove them. Signed-off-by:
Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Acked-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
-
- 06 Jun, 2013 1 commit
-
-
Thomas Petazzoni authored
The ranges DT entry needed by the PCIe controller is defined at the SoC .dtsi level. However, some boards have a NOR flash, and to support it, they need to override the SoC-level ranges property to add an additional range. Since PCIe and NOR support came separately, some boards were not properly changed to include the PCIe range in their ranges property at the .dts level. This commit fixes those platforms. Signed-off-by:
-
- 05 Jun, 2013 1 commit
-
-
Simon Baatz authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. Signed-off-by:
Simon Baatz <gmbnomis@gmail.com> Reviewed-by:
-
- 04 Jun, 2013 1 commit
-
-
Willy Tarreau authored
These aliases are used when feeding the DT from ATAGS to set the devices MAC addresses. Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
-
- 03 Jun, 2013 1 commit
-
-
Adam Baker authored
The Kirkwood CPU Freq driver needs a CPU definition in order for the probe routine to activate it. Add a suitable definition to kirkwood.dtsi This definition is only correct for single core SoCs. There is a dual core SoC in the kirkwood family (88F632X) but the rest of the Kirkwood drivers in the kernel don't currently support it. If they ever do the cpus definition would need to be duplicated in each of the SoC specific include files. Signed-off-by:
Adam Baker <linux@baker-net.org.uk> Tested-by:
-
- 27 May, 2013 23 commits
-
-
Valentin Longchamp authored
This controller is used to access the reset management FPGA of the km_kirkwood boards. Signed-off-by:
Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by:
-
Valentin Longchamp authored
Some kirkwood variants (for instance present in the prestera SoCs) do not have all the peripherals whose nodes are declared in kirkwood.dtsi. These missing peripherals are SATA, SDIO, and RTC. As discussed in [1], to avoid that these missing peripherals get initialized which could result in system hangs when accessing undocumented/not present HW registers, their corresponding OF nodes should not get declared at all for some kirkwood variants. The corresponding OF nodes of these peripherals thus are moved from kirkwood.dtsi to the kirkwood-628x.dtsi files so that they still are initialized for these variants where they are present. [1] http://lists.infradead.org/pipermail/linux-arm-kernel/2013-May/167154.htmlSigned-off-by:
-
Thomas Petazzoni authored
The Kirkwood-based PlatHome OpenBlocks A6 board has an Init button connected to MPP pin 38. This commit adds support for this button. Signed-off-by:
Atsushi Yamagata <yamagata@plathome.co.jp> Signed-off-by:
-
Thomas Petazzoni authored
Instead of having one separate pinmux configuration for each LED, for each GPIO of the GPIO header, for each DIP switch, this patch groups them together in configurations that make sense together: LEDs on one side, GPIOs of the GPIO header on another side, and DIP switches on yet another side. Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. Note that some of the LEDs pinmux configurations are kept in the pinctrl node, because they are not used by the gpio-leds driver. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
The Kirkwood iConnect Device Tree is currently using totally meaningless names for the pinmux configuration: pmx_gpio_XY. This patch fixes that by using some more meaningful names such as pmx_button_power. Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
Thomas Petazzoni authored
When the pinmux mechanism was added in Kirkwood, the device driver core was not yet providing the possibility of attaching pinmux configurations to all devices, drivers had to do it explicitly, and not all drivers were doing this. Now that the driver core does that in a generic way, it makes sense to attach the pinmux configuration to their corresponding devices. This allows the pinctrl subsystem to show in debugfs to which device is related which pins, for example: pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41 pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42 pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43 Signed-off-by:
-
- 21 May, 2013 1 commit
-
-
Thomas Petazzoni authored
The Armada XP GP board has two USB slots: one on the front side and one on the back side. This commit enables the two USB host controllers that correspond to those wo USB slots. Signed-off-by:
-
- 20 May, 2013 1 commit
-
-
Thomas Petazzoni authored
Besides the two "classic" USB interfaces with normal USB ports on the front side, the PlatHome OpenBlocks AX3 uses the third USB interface of the Marvell SoC in the mini-PCIe connector. This allows certain mini-PCIe cards to expose parts of their functionality as a USB peripheral. This commit enables this third USB interface in the OpenBlocks AX3 Device Tree, and also adds comments on top of the two other USB interfaces so that the Device Tree makes it clear which USB interface at the SoC level matches which USB interface visible on the board. Signed-off-by:
-
- 19 May, 2013 1 commit
-
-
Ezequiel Garcia authored
The Armada XP Development Board (DB-78460-BP) has a NOR flash device connected to the Device Bus. This commit adds the device tree node to support this device. This SoC supports a flexible and dynamic decoding window allocation scheme; but since this feature is still not implemented we need to specify the window base address in the device tree node itself. This base address has been selected in a completely arbitrary fashion. Signed-off-by:
-
- 15 May, 2013 2 commits
-
-
Simon Baatz authored
Signed-off-by:
-
Simon Baatz authored
In order to prepare the switch to the standard MMC device tree parser for mvsdio, adapt all current uses of mvsdio in the dts files to the standard format. Signed-off-by:
-
- 13 May, 2013 1 commit
-
-
Sebastian Hesselbarth authored
This patch adds the device tree node for si5351 clock generator and the corresponding oscillator connected to it. It also limits i2c frequency to 100kHz as there are bus locks reported on higher frequencies. Signed-off-by:
Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by:
-
- 12 May, 2013 2 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-traceLinus Torvalds authored
Pull tracing/kprobes update from Steven Rostedt: "The majority of these changes are from Masami Hiramatsu bringing kprobes up to par with the latest changes to ftrace (multi buffering and the new function probes). He also discovered and fixed some bugs in doing so. When pulling in his patches, I also found a few minor bugs as well and fixed them. This also includes a compile fix for some archs that select the ring buffer but not tracing. I based this off of the last patch you took from me that fixed the merge conflict error, as that was the commit that had all the changes I needed for this set of changes." * tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: tracing/kprobes: Support soft-mode disabling tracing/kprobes: Support ftrace_event_file base multibuffer tracing/kprobes: Pass trace_probe directly from dispatcher tracing/kprobes: Increment probe hit-count even if it is used by perf tracing/kprobes: Use bool for retprobe checker ftrace: Fix function probe when more than one probe is added ftrace: Fix the output of enabled_functions debug file ftrace: Fix locking in register_ftrace_function_probe() tracing: Add helper function trace_create_new_event() to remove duplicate code tracing: Modify soft-mode only if there's no other referrer tracing: Indicate enabled soft-mode in enable file tracing/kprobes: Fix to increment return event probe hit-count ftrace: Cleanup regex_lock and ftrace_lock around hash updating ftrace, kprobes: Fix a deadlock on ftrace_regex_lock ftrace: Have ftrace_regex_write() return either read or error tracing: Return error if register_ftrace_function_probe() fails for event_enable_func() tracing: Don't succeed if event_enable_func did not register anything ring-buffer: Select IRQ_WORK
-
- 11 May, 2013 3 commits
-
-
Linus Torvalds authored
Merge tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen Pull Xen bug-fixes from Konrad Rzeszutek Wilk: - More fixes in the vCPU PVHVM hotplug path. - Add more documentation. - Fix various ARM related issues in the Xen generic drivers. - Updates in the xen-pciback driver per Bjorn's updates. - Mask the x2APIC feature for PV guests. * tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen/pci: Used cached MSI-X capability offset xen/pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK xen: clear IRQ_NOAUTOEN and IRQ_NOREQUEST xen: mask x2APIC feature in PV xen: SWIOTLB is only used on x86 xen/spinlock: Fix check from greater than to be also be greater or equal to. xen/smp/pvhvm: Don't point per_cpu(xen_vpcu, 33 and larger) to shared_info xen/vcpu: Document the xen_vcpu_info and xen_vcpu xen/vcpu/pvhvm: Fix vcpu hotplugging hanging.
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull second SCSI update from James "Jaj B" Bottomley: "This is the final round of SCSI patches for the merge window. It consists mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc, be2iscsi, pm80xx, qla4x and ipr). There's also the power management updates that complete the patches in Jens' tree, an iscsi refcounting problem fix from the last pull, some dif handling in scsi_debug fixes, a few nice code cleanups and an error handling busy bug fix." * tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (92 commits) [SCSI] qla2xxx: Update firmware link in Kconfig file. [SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used [SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type [SCSI] pm80xx: thermal, sas controller config and error handling update [SCSI] pm80xx: NCQ error handling changes [SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers [SCSI] pm80xx: Changed module name and debug messages update [SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it [SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone [SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files [SCSI] pm80xx: MSI-X implementation for using 64 interrupts [SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve [SCSI] pm80xx: Multiple inbound/outbound queue configuration [SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC [SCSI] lpfc: fix up Kconfig dependencies [SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd [SCSI] sd: change to auto suspend mode [SCSI] sd: use REQ_PM in sd's runtime suspend operation [SCSI] qla4xxx: Fix iocb_cnt calculation in qla4xxx_send_mbox_iocb() [SCSI] ufs: Correct the expected data transfersize ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linuxLinus Torvalds authored
Pull idle update from Len Brown: "Add support for new Haswell-ULT CPU idle power states" * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: intel_idle: initial C8, C9, C10 support tools/power turbostat: display C8, C9, C10 residency
-
