- 18 Oct, 2021 1 commit
-
-
Shunsuke Mie authored
A comment for the dma_buf_vmap/vunmap() is not catching up a corresponding implementation. Signed-off-by:
Shunsuke Mie <mie@igel.co.jp> Link: https://patchwork.freedesktop.org/patch/msgid/20211008112009.118996-1-mie@igel.co.jpReviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
- 17 Oct, 2021 13 commits
-
-
Brian Norris authored
Fix some error handling here noticed in review of other changes. Fixes: 2d4f7bda ("drm/rockchip: dsi: migrate to use dw-mipi-dsi bridge driver") Signed-off-by:
Brian Norris <briannorris@chromium.org> Reported-by:
Chen-Yu Tsai <wenst@chromium.org> Reviewed-by:
Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20210928143413.v3.4.I8bb7a91ecc411d56bc155763faa15f289d7fc074@changeid
-
Brian Norris authored
Our probe() function never enabled this clock, so we shouldn't disable it if we fail to probe the bridge. Noted by inspection. Fixes: 2d4f7bda ("drm/rockchip: dsi: migrate to use dw-mipi-dsi bridge driver") Signed-off-by:
-
Brian Norris authored
Since commit 43c2de10 ("drm/rockchip: dsi: move all lane config except LCDC mux to bind()"), we perform most HW configuration in the bind() function. This configuration may be lost on suspend/resume, so we need to call it again. That may lead to errors like this after system suspend/resume: dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO panel-kingdisplay-kd097d04 ff960000.mipi.0: failed write init cmds: -110 Tested on Acer Chromebook Tab 10 (RK3399 Gru-Scarlet). Note that early mailing list versions of this driver borrowed Rockchip's downstream/BSP solution, to do HW configuration in mode_set() (which *is* called at the appropriate pre-enable() times), but that was discarded along the way. I've avoided that still, because mode_set() documentation doesn't suggest this kind of purpose as far as I can tell. Fixes: 43c2de10 ("drm/rockchip: dsi: move all lane config except LCDC mux to bind()") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Brian Norris authored
In commit 43c2de10 ("drm/rockchip: dsi: move all lane config except LCDC mux to bind()"), we moved most HW configuration to bind(), but we didn't move the runtime PM management. Therefore, depending on initial boot state, runtime-PM workqueue delays, and other timing factors, we may disable our power domain in between the hardware configuration (bind()) and when we enable the display. This can cause us to lose hardware state and fail to configure our display. For example: dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO panel-innolux-p079zca ff960000.mipi.0: failed to write command 0 or: dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO panel-kingdisplay-kd097d04 ff960000.mipi.0: failed write init cmds: -110 We should match the runtime PM to the lifetime of the bind()/unbind() cycle. Tested on Acer Chrometab 10 (RK3399 Gru-Scarlet), with panel drivers built either as modules or built-in. Side notes: it seems one is more likely to see this problem when the panel driver is built into the kernel. I've also seen this problem bisect down to commits that simply changed Kconfig dependencies, because it changed the order in which driver init functions were compiled into the kernel, and therefore the ordering and timing of built-in device probe. Fixes: 43c2de10 ("drm/rockchip: dsi: move all lane config except LCDC mux to bind()") Link: https://lore.kernel.org/linux-rockchip/9aedfb528600ecf871885f7293ca4207c84d16c1.camel@gmail.com/ Reported-by: <aleksandr.o.makarov@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Brian Norris authored
If hardware is malfunctioning (e.g., misconfigured clocks?), we can get stuck here forever, holding various DRM locks and eventually locking up the entire system. It's better to complain loudly and move on, than to lock up the system. In local tests, this operation takes less than 20ms. Signed-off-by:
-
Yang Li authored
Currently a plain integer is being used to nullify the pointer struct v3d_submit_ext *se. Use NULL instead. Cleans up sparse warnings: drivers/gpu/drm/v3d/v3d_gem.c:777:53: warning: Using plain integer as NULL pointer drivers/gpu/drm/v3d/v3d_gem.c:1010:45: warning: Using plain integer as NULL pointer Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Reviewed-by:
Melissa Wen <mwen@igalia.com> Signed-off-by:
Melissa Wen <melissa.srw@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/1634282081-72255-1-git-send-email-yang.lee@linux.alibaba.com
-
Shawn Guo authored
It adds a DRM panel driver for Sony Tulip Truly NT35521 5.24" 1280x720 DSI panel, which can be found on Sony Xperia M4 Aqua phone. The panel backlight is managed through DSI link. The driver is built using linux-mdss-dsi-panel-driver-generator[1], and additionally modeling the 5V control GPIOs with regulators and adding Backlight GPIO support. [1] https://github.com/msm8916-mainline/linux-mdss-dsi-panel-driver-generatorSigned-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210809051008.6172-3-shawn.guo@linaro.org
-
Shawn Guo authored
The Sony Tulip Truly NT35521 is a 5.24" 1280x720 DSI panel, which can be found on Sony Xperia M4 Aqua phone. The backlight is managed through DSI link. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
AngeloGioacchino Del Regno authored
This adds support for the BOE BF060Y8M-AJ0 5.99" AMOLED module that can be found in some F(x)Tec Pro1 and Elephone U1 devices. Signed-off-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Signed-off-by:
-
AngeloGioacchino Del Regno authored
Document the boe,bf060y8m-aj0 panel. Signed-off-by:
-
AngeloGioacchino Del Regno authored
Add a driver for panels using the Novatek NT35950 Display Driver IC, including support for the Sharp LS055D1SX04, found in some Sony Xperia Z5 Premium and XZ Premium smartphones. Signed-off-by:
Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by:
-
AngeloGioacchino Del Regno authored
The nt35950 IC from Novatek is a Driver IC used to drive MIPI-DSI panels, with Static RAM for content retention in command mode and also supports video mode with VESA Frame Buffer Compression or Display Stream Compression on single, or dual dsi port(s). This DDIC is also capable of upscaling an input image to the panel's native resolution, for example it can upscale a 1920x1080 input to 3840x2160 with either bilinear interpolation or pixel duplication. Signed-off-by:
-
Marek Vasut authored
Current code always sets reset line low in .pre_enable callback and holds it low for 10ms. This is sub-optimal and increases the time between enablement of the DSI83 and valid LVDS clock. Rework the reset handling such that the reset line is held low for 10ms both in probe() of the driver and .disable callback, which guarantees that the reset line was always held low for more than 10ms and therefore the reset line timing requirement is satisfied. Furthermore, move the reset handling into .enable callback so the entire DSI83 initialization is now in one place. This reduces DSI83 enablement delay by up to 10ms. Signed-off-by:
Marek Vasut <marex@denx.de> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: dri-devel@lists.freedesktop.org Signed-off-by:
-
- 16 Oct, 2021 4 commits
-
-
Michael Trimarchi authored
Depends in how logic is connected to the board the gpio is not stricly required. Signed-off-by:
Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by:
-
Michael Trimarchi authored
W552946ABA is a panel by Wanchanglong. This panel utilizes the Ilitek ILI9881D controller. Add this panel's initialzation sequence and timing to ILI9881D driver. Tested on px30-evb v11 Signed-off-by:
-
Michael Trimarchi authored
It utilizes an Ilitek ILI9881D controller chip, but its compatible with ili9881c so should be added to ilitek,ili9881c file. Add the compatible string for it. Signed-off-by:
-
Michael Trimarchi authored
Wanchanglong Electronics Technology is a company to provide LCD modules. Signed-off-by:
-
- 15 Oct, 2021 9 commits
-
-
AngeloGioacchino Del Regno authored
Convert the Silicon Image SiI9234 HDMI/MHL bridge documentation to YAML. Signed-off-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by:
-
Qing Wang authored
coccicheck complains about the use of snprintf() in sysfs show functions. Fix the coccicheck warning: WARNING: use scnprintf or sprintf. Use sysfs_emit instead of scnprintf or sprintf makes more sense. Signed-off-by:
Qing Wang <wangqing@vivo.com> Signed-off-by:
-
Qing Wang authored
coccicheck complains about the use of snprintf() in sysfs show functions. Fix the coccicheck warning: WARNING: use scnprintf or sprintf. Use sysfs_emit instead of scnprintf or sprintf makes more sense. Signed-off-by:
-
AngeloGioacchino Del Regno authored
Convert the NXP PTN3460 eDP to LVDS bridge documentation to YAML. Signed-off-by:
-
Sam Ravnborg authored
Commit build fix that I forgot to amend :-( Fixes: 50848e37 ("drm/tiny: add driver for newhaven, 1.8-128160EF") Signed-off-by:
-
Daniel Mack authored
This patch adds support for Newhaven's NHD-1.8-128160EF display, featuring an Ilitek ILI9163 controller. Signed-off-by:
Daniel Mack <daniel@zonque.org> Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by:
Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by:
-
Daniel Mack authored
This adds documentation for a new ILI9163 based, SPI connected display. Signed-off-by:
-
Qing Wang authored
show() must not use snprintf() when formatting the value to be returned to user space. Fix the following coccicheck warning: drivers/gpu/drm/panel/panel-dsi-cm.c:251: WARNING: use scnprintf or sprintf. drivers/gpu/drm/panel/panel-dsi-cm.c:271: WARNING: use scnprintf or sprintf. Use sysfs_emit instead of scnprintf or sprintf makes more sense. Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by:
-
Neil Armstrong authored
Since we allow interlace on the encoder, also allow it on the bridge so we can allow interlaced modes when using DRM_BRIDGE_ATTACH_NO_CONNECTOR. Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Acked-by:
-
- 14 Oct, 2021 13 commits
-
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, the error value gets printed. Signed-off-by:
Cai Huoqing <caihuoqing@baidu.com> Signed-off-by:
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, the error value gets printed. Signed-off-by:
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, the error value gets printed. Signed-off-by:
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, the error value gets printed. Signed-off-by:
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, the error value gets printed. Signed-off-by:
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, the error value gets printed. Signed-off-by:
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, the error value gets printed. Signed-off-by:
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, and the error value gets printed. Signed-off-by:
Icenowy Zheng <icenowy@aosc.io> Signed-off-by:
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, and the error value gets printed. Signed-off-by:
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, and the error value gets printed. Signed-off-by:
-
Cai Huoqing authored
When possible use dev_err_probe help to properly deal with the PROBE_DEFER error, the benefit is that DEFER issue will be logged in the devices_deferred debugfs file. And using dev_err_probe() can reduce code size, and the error value gets printed. Signed-off-by:
-
Cai Huoqing authored
Removed extra whitespace before dev_err_probe() according to coding style. Signed-off-by:
-
Brian Norris authored
Many DSI panel drivers fail to clean up their panel references on mipi_dsi_attach() failure, so we're leaving a dangling drm_panel reference to freed memory. Clean that up on failure. Noticed by inspection, after seeing similar problems on other drivers. Therefore, I'm not marking Fixes/stable. Signed-off-by:
-
