Merge tag 'usb-serial-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v3.18-rc5

Here are a few fixes for reported problems including a possible
null-deref on probe with keyspan, a misbehaving modem, and a couple of
issues with the USB console.

Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>

Merge tag 'fixes-for-v3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v3.19-rc5

Just three fixes this time. An oops fix in ep_write() from gadgetfs,
another oops for the Atmel UDC when unloading a gadget driver and
the fix for PHY deferred probing.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Conflicts:
	drivers/usb/phy/phy.c

If a USB serial device (e.g. /dev/ttyUSB0) with an active program is
unplugged, an -ENODEV (19) error will be produced after it gives up
trying to resubmit a read.

  usb_serial_generic_submit_read_urb - usb_submit_urb failed: -19

Add -ENODEV as one of the permanent errors along with -EPERM that
usb_serial_generic_submit_read_urb() handles quietly without an error.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

If a USB serial device is unplugged while there is an active program
using the device it may spam the logs with -EPROTO (71) messages as it
attempts to retry.

Most serial usb drivers (metro-usb, pl2303, mos7840, ...) only output
these messages for debugging.  The generic driver treats these as
errors.

Change the default output for the generic serial driver from error to
debug to silence these non-critical errors.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

Use tty kref to release the fake tty in usb_console_setup to avoid use
after free if the underlying serial driver has acquired a reference.

Note that using the tty destructor release_one_tty requires some more
state to be initialised.

Fixes: 4a90f09b ("tty: usb-serial krefs")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB console currently allocates a temporary fake tty which is used
to pass terminal settings to the underlying serial driver.

The tty struct is not fully initialised, something which can lead to a
lockdep warning (or worse) if a serial driver tries to acquire a
line-discipline reference:

	usbserial: USB Serial support registered for pl2303
	pl2303 1-2.1:1.0: pl2303 converter detected
	usb 1-2.1: pl2303 converter now attached to ttyUSB0
	INFO: trying to register non-static key.
	the code is fine but needs lockdep annotation.
	turning off the locking correctness validator.
	CPU: 0 PID: 68 Comm: udevd Tainted: G        W      3.18.0-rc5 #10
	[<c0016f04>] (unwind_backtrace) from [<c0013978>] (show_stack+0x20/0x24)
	[<c0013978>] (show_stack) from [<c0449794>] (dump_stack+0x24/0x28)
	[<c0449794>] (dump_stack) from [<c006f730>] (__lock_acquire+0x1e50/0x2004)
	[<c006f730>] (__lock_acquire) from [<c0070128>] (lock_acquire+0xe4/0x18c)
	[<c0070128>] (lock_acquire) from [<c027c6f8>] (ldsem_down_read_trylock+0x78/0x90)
	[<c027c6f8>] (ldsem_down_read_trylock) from [<c027a1cc>] (tty_ldisc_ref+0x24/0x58)
	[<c027a1cc>] (tty_ldisc_ref) from [<c0340760>] (usb_serial_handle_dcd_change+0x48/0xe8)
	[<c0340760>] (usb_serial_handle_dcd_change) from [<bf000484>] (pl2303_read_int_callback+0x210/0x220 [pl2303])
	[<bf000484>] (pl2303_read_int_callback [pl2303]) from [<c031624c>] (__usb_hcd_giveback_urb+0x80/0x140)
	[<c031624c>] (__usb_hcd_giveback_urb) from [<c0316fc0>] (usb_giveback_urb_bh+0x98/0xd4)
	[<c0316fc0>] (usb_giveback_urb_bh) from [<c0042e44>] (tasklet_hi_action+0x9c/0x108)
	[<c0042e44>] (tasklet_hi_action) from [<c0042380>] (__do_softirq+0x148/0x42c)
	[<c0042380>] (__do_softirq) from [<c00429cc>] (irq_exit+0xd8/0x114)
	[<c00429cc>] (irq_exit) from [<c007ae58>] (__handle_domain_irq+0x84/0xdc)
	[<c007ae58>] (__handle_domain_irq) from [<c000879c>] (omap_intc_handle_irq+0xd8/0xe0)
	[<c000879c>] (omap_intc_handle_irq) from [<c0014544>] (__irq_svc+0x44/0x7c)
	Exception stack(0xdf4e7f08 to 0xdf4e7f50)
	7f00:                   debc0b80 df4e7f5c 00000000 00000000 debc0b80 be8da96c
	7f20: 00000000 00000128 c000fc84 df4e6000 00000000 df4e7f94 00000004 df4e7f50
	7f40: c038ebc0 c038d74c 600f0013 ffffffff
	[<c0014544>] (__irq_svc) from [<c038d74c>] (___sys_sendmsg.part.29+0x0/0x2e0)
	[<c038d74c>] (___sys_sendmsg.part.29) from [<c038ec08>] (SyS_sendmsg+0x18/0x1c)
	[<c038ec08>] (SyS_sendmsg) from [<c000fa00>] (ret_fast_syscall+0x0/0x48)
	console [ttyUSB0] enabled

Fixes: 36697529 ("tty: Replace ldisc locking with ldisc_sem")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

When unloading the module 'g_hid.ko', the urb request will be dequeued and the
completion routine will be excuted. If there is no urb packet, the urb request
will not be added to the endpoint queue and the completion routine pointer in
urb request is NULL.

Accessing to this NULL function pointer will cause the Oops issue reported
below.

Add the code to check if the urb request is in the endpoint queue
or not. If the urb request is not in the endpoint queue, a negative
error code will be returned.

Here is the Oops log:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = dedf0000
[00000000] *pgd=3ede5831, *pte=00000000, *ppte=00000000
Internal error: Oops: 80000007 [#1] ARM
Modules linked in: g_hid(-) usb_f_hid libcomposite
CPU: 0 PID: 923 Comm: rmmod Not tainted 3.18.0+ #2
Hardware name: Atmel SAMA5 (Device Tree)
task: df6b1100 ti: dedf6000 task.ti: dedf6000
PC is at 0x0
LR is at usb_gadget_giveback_request+0xc/0x10
pc : [<00000000>]    lr : [<c02ace88>]    psr: 60000093
sp : dedf7eb0  ip : df572634  fp : 00000000
r10: 00000000  r9 : df52e210  r8 : 60000013
r7 : df6a9858  r6 : df52e210  r5 : df6a9858  r4 : df572600
r3 : 00000000  r2 : ffffff98  r1 : df572600  r0 : df6a9868
Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c53c7d  Table: 3edf0059  DAC: 00000015
Process rmmod (pid: 923, stack limit = 0xdedf6230)
Stack: (0xdedf7eb0 to 0xdedf8000)
7ea0:                                     00000000 c02adbbc df572580 deced608
7ec0: df572600 df6a9868 df572634 c02aed3c df577c00 c01b8608 00000000 df6be27c
7ee0: 00200200 00100100 bf0162f4 c000e544 dedf6000 00000000 00000000 bf010c00
7f00: bf0162cc bf00159c 00000000 df572980 df52e218 00000001 df5729b8 bf0031d0
[..]
[<c02ace88>] (usb_gadget_giveback_request) from [<c02adbbc>] (request_complete+0x64/0x88)
[<c02adbbc>] (request_complete) from [<c02aed3c>] (usba_ep_dequeue+0x70/0x128)
[<c02aed3c>] (usba_ep_dequeue) from [<bf010c00>] (hidg_unbind+0x50/0x7c [usb_f_hid])
[<bf010c00>] (hidg_unbind [usb_f_hid]) from [<bf00159c>] (remove_config.isra.6+0x98/0x9c [libcomposite])
[<bf00159c>] (remove_config.isra.6 [libcomposite]) from [<bf0031d0>] (__composite_unbind+0x34/0x98 [libcomposite])
[<bf0031d0>] (__composite_unbind [libcomposite]) from [<c02acee0>] (usb_gadget_remove_driver+0x50/0x78)
[<c02acee0>] (usb_gadget_remove_driver) from [<c02ad570>] (usb_gadget_unregister_driver+0x64/0x94)
[<c02ad570>] (usb_gadget_unregister_driver) from [<bf0160c0>] (hidg_cleanup+0x10/0x34 [g_hid])
[<bf0160c0>] (hidg_cleanup [g_hid]) from [<c0056748>] (SyS_delete_module+0x118/0x19c)
[<c0056748>] (SyS_delete_module) from [<c000e3c0>] (ret_fast_syscall+0x0/0x30)
Code: bad PC value
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
[nicolas.ferre@atmel.com: reworked the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 914a3f3b ("USB: add atmel_usba_udc driver")
Cc: <stable@vger.kernel.org> # 2.6.x-ish
Signed-off-by: Felipe Balbi <balbi@ti.com>

We try to free an ERR_PTR on this error path.

Fixes: b44be246 ('usb: gadget: gadgetfs: Free memory allocated by memdup_user()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Commit 1290a958 ("usb: phy: propagate __of_usb_find_phy()'s error on
failure") actually broke the deferred probing mechanism, since it now returns
EPROBE_DEFER only when the try_module_get call fails, but not when the phy
lookup does.

All the other similar functions seem to return ENODEV when try_module_get
fails, and the error code of either __usb_find_phy or __of_usb_find_phy
otherwise.

In order to have a consistent behaviour, and a meaningful EPROBE_DEFER, always
return EPROBE_DEFER when __(of_)usb_find_phy fails to look up the requested
phy, that will be propagated by the caller, and ENODEV if try_module_get fails.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 8dccddbc ("OHCI: final fix for NVIDIA problems (I hope)")
introduced into 3.1.9 broke boot on e.g. Freescale P2020DS development
board. The code path that was previously specific to NVIDIA controllers
had then become taken for all chips.

However, the M5237 installed on the board wedges solid when accessing
its base+OHCI_FMINTERVAL register, making it impossible to boot any
kernel newer than 3.1.8 on this particular and apparently other similar
machines.

Don't readl() and writel() base+OHCI_FMINTERVAL on PCI ID 10b9:5237.

The patch is suitable for the -next tree as well as all maintained
kernels up to 3.2 inclusive.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org> # 3.2
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Just like all previous UAS capable Seagate disk enclosures, these need the
US_FL_NO_ATA_1X to not crash when udev probes them.

Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Our detection logic to avoid doing UAS on ASM1051 bridge chips causes problems
with newer ASM1153 disk enclosures in 2 ways:

1) Some ASM1153 disk enclosures re-use the ASM1051 device-id of 5106, which
   we assume is always an ASM1051, so remove the quirk for 5106, and instead
   use the same detection logic as we already use for device-id 55aa, which is
   used for all of ASM1051, ASM1053 and ASM1153 devices <sigh>.

2) Our detection logic to differentiate between ASM1051 and ASM1053 sees
   ASM1153 devices as ASM1051 because they have 32 streams like ASM1051 devs.
   Luckily the ASM1153 descriptors are not 100% identical, unlike the previous
   models the ASM1153 has bMaxPower == 0, so use that to differentiate it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Coverity: CID 1260069
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The commit 1290a958 ("usb: phy: propagate __of_usb_find_phy()'s error on
failure") changed the condition to return -EPROBE_DEFER to host driver.
Originally the Tegra host driver depended on the returned -EPROBE_DEFER to
get the phy device later when booting. Now we have to do that explicitly.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Apricorn SATA dongle will occasionally return "USBSUSBSUSB" in
response to SCSI commands when running in UAS mode.  Therefore,
disable UAS mode on this dongle.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Like the JMicron JMS567 enclosures with the JMS566 choke on report-opcodes,
so avoid it.
Tested-and-reported-by: Takeo Nakayama <javhera@gmx.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is yet another Seagate device which needs the US_FL_NO_ATA_1X quirk
Reported-by: Marcin Zajączkowski <mszpak@wp.pl>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Streams do not work reliabe on Fresco Logic FL1000G xhci controllers,
trying to use them results in errors like this:

21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3570 9067b000 00000000 05000000 01078001
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3580 9067b400 00000000 05000000 01038001

As always I've ordered a pci-e addon card with a Fresco Logic controller for
myself to see if I can come up with a better fix then the big hammer, in
the mean time this will make uas devices work again (in usb-storage mode)
for FL1000G users.
Reported-by: Marcin Zajączkowski <mszpak@wp.pl>
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB stack uses error code -ENOSPC to indicate that the periodic
schedule is too full, with insufficient bandwidth to accommodate a new
allocation.  It uses -EFBIG to indicate that an isochronous transfer
could not be linked into the schedule because it would exceed the
number of isochronous packets the host controller driver can handle
(generally because the new transfer would extend too far into the
future).

ehci-hcd uses the wrong error code at one point.  This patch fixes it,
along with a misleading comment and debugging message.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit c3ee9b76 (EHCI: improved logic for isochronous scheduling)
introduced the idea of using ehci->last_iso_frame as the origin (or
base) for the circular calculations involved in modifying the
isochronous schedule.  However, the new code it added used
ehci->last_iso_frame before the value was properly initialized.  This
patch rectifies the mistake by moving the initialization lines earlier
in iso_stream_schedule().

This fixes Bugzilla #72891.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: c3ee9b76Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Tested-by: Joe Bryant <tenminjoe@yahoo.com>
Tested-by: Martin Long <martin@longhome.co.uk>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Solves xhci error cases with debug messages:
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 1-6: hub failed to enable device, error -22

xhci will give a context state error if we try to set a slot in default
state to the same default state with a special address device command.

Turns out this happends in several cases:
- retry reading the device rescriptor in hub_port_init()
- usb_reset_device() is called for a slot in default state
- in resume path, usb_port_resume() calls hub_port_init()

The default state is usually reached from most states with a reset device
command without any context state errors, but using the address device
command with BSA bit set (block set address) only works from the enabled
state and will otherwise cause context error.

solve this by checking if we are already in the default state before issuing
a address device BSA=1 command.

Fixes: 48fc7dbd ("usb: xhci: change enumeration scheme to 'new scheme'")
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 14b4099c

It moved platform_set_drvdata(pdev, ci) before hcd is created,
and the hcd will assign itself as ci controller's drvdata during
the hcd creation function (in usb_create_shared_hcd), so it
overwrites the real ci's drvdata which we want to use.

So, if the controller is at host mode, the system suspend
API will get the wrong struct ci_hdrc pointer, and cause the
oops.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-3.19-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus

Kishon writes:

misc fixes in PHY drivers

As has been discussed in the thread starting with
https://lkml.kernel.org/g/549748e9.d+SiJzqu50f1r4lSAL043YSc@arcor.de
Sierra Wireless MC73xx devices with USB VID/PID 0x1199:0x68c0 require the
option_send_setup() code to be used on the USB interface for the AT port
to make unsolicited response codes work correctly. Move these devices from
the qcserial driver where they have been added by commit
70a3615f ("usb: qcserial: add Sierra Wireless
MC73xx") to the option driver and add a MC73xx-specific blacklist
to ensure that
1. the sendsetup code is not used for the DIAG/DM and NMEA interfaces
2. the option driver does not attach to the QMI/network interfaces
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Added virtual com port VID/PID entries for CEL USB sticks and MeshWorks
devices.
Signed-off-by: David Peterson <david.peterson@cel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Fix null-pointer dereference during probe if the interface-status
completion handler is called before the individual ports have been set
up.

Fixes: f79b2d0f ("USB: keyspan: fix NULL-pointer dereferences and
memory leaks")
Reported-by: Richard <richjunk@pacbell.net>
Tested-by: Richard <richjunk@pacbell.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Fixing typo for MeshConnect IDs. The original PID (0x8875) is not in
production and is not needed. Instead it has been changed to the
official production PID (0x8857).
Signed-off-by: Preston Fick <pffick@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Pull KVM fixes from Paolo Bonzini:
 "The important fixes are for two bugs introduced by the merge window.

  On top of this, add a couple of WARN_ONs and stop spamming dmesg on
  pretty much every boot of a virtual machine"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: warn on more invariant breakage
  kvm: fix sorting of memslots with base_gfn == 0
  kvm: x86: drop severity of "generation wraparound" message
  kvm: x86: vmx: reorder some msr writing

Pull vfs fix from Al Viro:
 "An embarrassing bug in lustre patches from this cycle ;-/"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  [regression] braino in "lustre: use is_root_inode()"

Modifying a non-existent slot is not allowed.  Also check that the
first loop doesn't move a deleted slot beyond the used part of
the mslots array.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Before commit 0e60b079 (kvm: change memslot sorting rule from size
to GFN, 2014-12-01), the memslots' sorting key was npages, meaning
that a valid memslot couldn't have its sorting key equal to zero.
On the other hand, a valid memslot can have base_gfn == 0, and invalid
memslots are identified by base_gfn == npages == 0.

Because of this, commit 0e60b079 broke the invariant that invalid
memslots are at the end of the mslots array.  When a memslot with
base_gfn == 0 was created, any invalid memslot before it were left
in place.

This can be fixed by changing the insertion to use a ">=" comparison
instead of "<=", but some care is needed to avoid breaking the case
of deleting a memslot; see the comment in update_memslots.

Thanks to Tiejun Chen for posting an initial patch for this bug.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull sound fixes from Takashi Iwai:
 "Just a couple of fixes for the new Intel Skylake HD-audio support"

* tag 'sound-3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda_intel: apply the Seperate stream_tag for Skylake
  ALSA: hda_controller: Separate stream_tag for input and output streams.

Since most virtual machines raise this message once, it is a bit annoying.
Make it KERN_DEBUG severity.

Cc: stable@vger.kernel.org
Fixes: 7a2e8aafSigned-off-by: Paolo Bonzini <pbonzini@redhat.com>

The commit 34a1cd60, "x86: vmx: move some vmx setting from
vmx_init() to hardware_setup()", tried to refactor some codes
specific to vmx hardware setting into hardware_setup(), but some
msr writing should depend on our previous setting condition like
enable_apicv, enable_ept and so on.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

In one of the places (ll_md_blocking_ast()) we had open-coded
!is_root_inode(inode) and replaced it with is_root_inode(inode).
See the last chunk of f76c23:
-                   inode != inode->i_sb->s_root->d_inode)
+                   is_root_inode(inode))
should've been
+                   !is_root_inode(inode))
obviously...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull parisc build fix from Helge Deller:
 "This unbreaks the kernel compilation on parisc with gcc-4.9"

* 'parisc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: fix out-of-register compiler error in ldcw inline assembler function

The __ldcw macro has a problem when its argument needs to be reloaded from
memory. The output memory operand and the input register operand both need to
be reloaded using a register in class R1_REGS when generating 64-bit code.
This fails because there's only a single register in the class. Instead, use a
memory clobber. This also makes the __ldcw macro a compiler memory barrier.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org>        [3.13+]
Signed-off-by: Helge Deller <deller@gmx.de>

The total stream number of Skylake's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.

This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Implemented separate stream_tag assignment for input and output streams.
According to hda specification stream tag must be unique throughout the
input streams group, however an output stream might use a stream tag
which is already in use by an input stream. This change is necessary
to support HW which provides a total of more than 15 stream DMA engines
which with legacy implementation causes an overflow on SDxCTL.STRM
field (and the whole SDxCTL register) and as a result usage of
Reserved value 0 in the SDxCTL.STRM field which confuses HDA controller.
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>