- 05 Sep, 2013 1 commit
-
-
Benjamin Herrenschmidt authored
From Anatolij: << There are cleanups for some mpc5121 specific drivers and DTS files in preparation to switch mpc5121 clock support to a clock driver based on common clock framework. Additionally Sebastian fixed the mpc52xx PIC driver so that it builds when using older gcc versions. >>
-
- 28 Aug, 2013 2 commits
-
-
Benjamin Herrenschmidt authored
This file is entirely pseries specific nowadays, so move it out of arch/powerpc/kernel where it doesn't belong anymore. Signed-off-by:Benjamin Herrenschmidt <benh@kernel.crashing.org>
-
Benjamin Herrenschmidt authored
Merge recent fixes to lparcfg so subsequent patches can move the whole file to arch/powerpc/platforms/pseries
-
- 27 Aug, 2013 27 commits
-
-
Benjamin Herrenschmidt authored
With OPAL v3 we can return secondary CPUs to firmware on kexec. This allows firmware to do various cleanups making things generally more reliable, and will enable the "new" kernel to call OPAL to perform some reconfiguration tasks early on that can only be done while all the CPUs are in firmware. Signed-off-by: -
Eugene Surovegin authored
This solves a problem observed in kexec'ed kernel where 200ms timeout is too short and bootconsole fails to initialize. Console did eventually become workable but much later into the boot process. Observed timeout was around 260ms, but I decided to make it a little bigger for more reliability. This has been tested on Power7 machine with Petitboot as a primary bootloader and PowerNV firmware. CC: <stable@vger.kernel.org> Signed-off-by:
Eugene Surovegin <surovegin@google.com> Signed-off-by:
-
Paul Mackerras authored
On 64-bit, __pa(&static_var) gets miscompiled by recent versions of gcc as something like: addis 3,2,.LANCHOR1+4611686018427387904@toc@ha addi 3,3,.LANCHOR1+4611686018427387904@toc@l This ends up effectively ignoring the offset, since its bottom 32 bits are zero, and means that the result of __pa() still has 0xC in the top nibble. This happens with gcc 4.8.1, at least. To work around this, for 64-bit we make __pa() use an AND operator, and for symmetry, we make __va() use an OR operator. Using an AND operator rather than a subtraction ends up with slightly shorter code since it can be done with a single clrldi instruction, whereas it takes three instructions to form the constant (-PAGE_OFFSET) and add it on. (Note that MEMORY_START is always 0 on 64-bit.) CC: <stable@vger.kernel.org> Signed-off-by:Paul Mackerras <paulus@samba.org> Signed-off-by:
-
Benjamin Herrenschmidt authored
/proc/powerpc/lparcfg is an ancient facility (though still actively used) which allows access to some informations relative to the partition when running underneath a PAPR compliant hypervisor. It makes no sense on non-pseries machines. However, currently, not only can it be created on these if the kernel has pseries support, but accessing it on such a machine will crash due to trying to do hypervisor calls. In fact, it should also not do HV calls on older pseries that didn't have an hypervisor either. Finally, it has the plumbing to be a module but is a "bool" Kconfig option. This fixes the whole lot by turning it into a machine_device_initcall that is only created on pseries, and adding the necessary hypervisor check before calling the H_GET_EM_PARMS hypercall CC: <stable@vger.kernel.org> Signed-off-by: -
Benjamin Herrenschmidt authored
The "rmci" stuff only exists on 64-bit Signed-off-by: -
Michael Neuling authored
As suggested by paulus we can simplify the Data Stream Control Register (DSCR) Facility Status and Control Register (FSCR) handling. Firstly, we simplify the asm by using a rldimi. Secondly, we now use the FSCR only to control the DSCR facility, rather than both the FSCR and HFSCR. Users will see no functional change from this but will get a minor speedup as they will trap into the kernel only once (rather than twice) when they first touch the DSCR. Also, this changes removes a bunch of ugly FTR_SECTION code. Signed-off-by:
Michael Neuling <mikey@neuling.org> Signed-off-by:
-
Benjamin Herrenschmidt authored
Merge stuff that already went into Linus via "merge" which are pre-reqs for subsequent patches
-
Tyrel Datwyler authored
Calls to dlpar_detach_node do not iterate over child nodes detaching them as well. By iterating and detaching the child nodes we ensure that they have the OF_DETACHED flag set and that their reference counts are decremented such that the node will be freed from memory by of_node_release. Signed-off-by:
Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Acked-by:
Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by:
-
Tyrel Datwyler authored
The node to be detached is retrieved via its phandle by a call to of_find_node_by_phandle which increments the ref count. We need a matching call to of_node_put to decrement the ref count and ensure the node is actually freed. Signed-off-by:
-
Tyrel Datwyler authored
Currently the device nodes created in the device subtree returned by a call to dlpar_configure_connector are all named in the root node. This is because the the node name in the work area returned by ibm,configure-connector rtas call only contains the node name and not the entire node path. Passing the parent node where the new subtree will be created to dlpar_configure_connector allows the correct node path to be prefixed in the full_name field. Signed-off-by:
-
Tyrel Datwyler authored
Currently the OF_DYNAMIC and kref initialization for a node happens in dlpar_attach_node. However, a node passed to dlpar_attach_node may be a tree containing child nodes, and no initialization traversal is done on the tree. Since the children never get their kref initialized or the OF_DYNAMIC flag set these nodes are prevented from ever being released from memory should they become detached. This initialization step is better done at the time each node is allocated in dlpar_parse_cc_node. Signed-off-by:
-
Tyrel Datwyler authored
On the first call to ibm,update-properties for a node the first property returned is the full node path. Currently this is not parsed correctly by the update_dt_node function. Commit 2e9b7b02 attempted to fix this, but was incorrect as it made a wrong assumption about the layout of the first property in the work area. Further, if ibm,update-properties must be called multiple times for the same node this special property should only be skipped after the initial call. The first property descriptor returned consists of the property name, property value length, and property value. The property name is an empty string, property length is encoded in 4 byte integer, and the property value is the node path. Signed-off-by:
-
Tyrel Datwyler authored
The work area buffer returned by the ibm,update-properties rtas call contains 20 bytes of header information prior to the property value descriptor data. Currently update_dt_node tries to advance over this header using sizeof(upwa). The update_props_workarea struct contains 20 bytes worth of fields, that map to the relevant header data, but the sizeof the structure is 24 bytes due to 4 bytes of padding at the end of the structure. Packing the structure ensures that we don't advance too far over the rtas buffer. Signed-off-by:
-
Tyrel Datwyler authored
The rc variable is initially used to store the return code from the ibm,update-properties rtas call which returns 0 or 1 on success. A return code of 1 indicates that ibm,update-properties must be called again for the node. However, the rc variable is overwritten by a call to update_dt_prop which returns 0 on success. This results in ibm,update-properties not being called again for the given node when the rtas call rc was previously 1. Signed-off-by:
-
Tyrel Datwyler authored
The update_dt_prop helper function fails to set the IN/OUT parameter prop to NULL after a complete property has been parsed from the work area returned by the ibm,update-properties rtas function. This results in the property list of the device node being updated is corrupted and becomes a loop since the same property structure is used repeatedly. Signed-off-by:
-
Michael Ellerman authored
In the program check handler we handle some causes with interrupts off and others with interrupts on. We need to enable interrupts to handle the emulation cases, because they access userspace memory and might sleep. For faults in the kernel we don't want to do any emulation, and emulate_instruction() enforces that. do_mathemu() doesn't but probably should. The other disadvantage of enabling interrupts for kernel faults is that we may take another interrupt, and recurse. As seen below: --- Exception: e40 at c000000000004ee0 performance_monitor_relon_pSeries_1 [link register ] c00000000000f858 .arch_local_irq_restore+0x38/0x90 [c000000fb185dc10] 0000000000000000 (unreliable) [c000000fb185dc80] c0000000007d8558 .program_check_exception+0x298/0x2d0 [c000000fb185dd00] c000000000002f40 emulation_assist_common+0x140/0x180 --- Exception: e40 at c000000000004ee0 performance_monitor_relon_pSeries_1 [link register ] c00000000000f858 .arch_local_irq_restore+0x38/0x90 [c000000fb185dff0] 00000000008b9190 (unreliable) [c000000fb185e060] c0000000007d8558 .program_check_exception+0x298/0x2d0 So avoid both problems by checking if the fault was in the kernel and skipping the enable of interrupts and the emulation. Go straight to delivering the SIGILL, which for kernel faults calls die() and so on, dropping us in the debugger etc. Signed-off-by:
Michael Ellerman <michael@ellerman.id.au> Signed-off-by:
-
Michael Ellerman authored
This makes back traces and profiles easier to read. Signed-off-by:
-
Michael Ellerman authored
The symbols that name some of our exception trampolines are ahead of the location they name. In most cases this is OK because the code is tightly packed, but in some cases it means the symbol floats ahead of the correct location, eg: c000000000000ea0 <performance_monitor_pSeries_1>: ... c000000000000f00: 7d b2 43 a6 mtsprg 2,r13 Fix them all by moving the symbol after the set of the location. While we're moving them anyway, rename them to loose the camelcase and to make it clear that they are trampolines. Signed-off-by: -
Michael Ellerman authored
We haven't updated these for a while it seems, it's nice to have in the oops output. Signed-off-by:
-
Michael Ellerman authored
The spec says it "may be problematic" if CPU x registers the VPA of CPU y. Add a warning in case we ever do that. Signed-off-by:
-
Michael Ellerman authored
People have been dropping things in here without updating the index, do it for them. Signed-off-by:
-
Anton Blanchard authored
The VSX alignment handler needs to write out the existing VSX state to memory before operating on it (flush_vsx_to_thread()). If we take a VSX alignment exception in the kernel bad things will happen. It looks like we could write the kernel state out to the user process, or we could handle the kernel exception using data from the user process (depending if MSR_VSX is set or not). Worse still, if the code to read or write the VSX state causes an alignment exception, we will recurse forever. I ended up with hundreds of megabytes of kernel stack to look through as a result. Floating point and SPE code have similar issues but already include a user check. Add the same check to emulate_vsx(). With this patch any unaligned VSX loads and stores in the kernel will show up as a clear oops rather than silent corruption of kernel or userspace VSX state, or worse, corruption of a potentially unlimited amount of kernel memory. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Deepthi Dharwar authored
As a part of pseries_idle backend driver cleanup to make the code common to both pseries and powernv platforms, it is necessary to move the backend-driver code to drivers/cpuidle. As a pre-requisite for that, it is essential to move plpar_wrapper.h to include/asm. Signed-off-by:
Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by:
-
Deepthi Dharwar authored
As a part of pseries_idle cleanup to make the backend driver code common to both pseries and powernv. Remove non-essential smt_snooze_delay declaration in pseries.h header file and pseries.h file inclusion in pseries/processor_idle.c Signed-off-by:
-
Tom Musta authored
The stmw instruction was incorrectly decoded as an update form instruction and thus the RA register was being clobbered. Also, the utility routine to write memory to unaligned addresses breaks the operation into smaller aligned accesses but was incorrectly incrementing the address by only one; it needs to increment the address by the size of the smaller aligned chunk. Signed-off-by:
Tom Musta <tmusta@us.ibm.com> Signed-off-by:
-
Nathan Fontenot authored
Memory I/O resources need to be marked as busy or else we cannot remove them when doing memory hot remove. Signed-off-by:
-
Benjamin Herrenschmidt authored
Latest FSL updates from Scott: << Highlights include changes in compiler flag settings on e500 family cores, booke64 hibernation support, support for two new boards, and an erratum workaround. >>
-
- 24 Aug, 2013 6 commits
-
-
Mingkai Hu authored
C293PCIE board is a series of Freescale PCIe add-in cards to perform as public key crypto accelerator or secure key management module. - 512KB platform SRAM in addition to 512K L2 Cache/SRAM - 512MB soldered DDR3 32bit memory - CPLD System Logic - 64MB x16 NOR flash and 4GB x8 NAND flash - 16MB SPI flash Signed-off-by:
Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by:
Po Liu <Po.Liu@freescale.com> Signed-off-by:
Scott Wood <scottwood@freescale.com>
-
Mingkai Hu authored
Signed-off-by:
-
Mingkai Hu authored
Add device tree for SEC 6.0 used on C29x silicon. Signed-off-by:
-
Wang Dongsheng authored
Update the 64-bit hibernation code to support Book E CPUs. Some registers and instructions are not defined for Book3e (SDR reg, tlbia instruction). SDR: Storage Description Register. Book3S and Book3E have different address translation mode, we do not need HTABORG & HTABSIZE to translate virtual address to real address. More registers are saved in BookE-64bit.(TCR, SPRG1) Signed-off-by:
Wang Dongsheng <dongsheng.wang@freescale.com> Signed-off-by:
-
Chunhe Lan authored
P1023RDB Specification: ----------------------- Memory subsystem: 512MB DDR3 (Fixed DDR on board) 64MB NOR flash 128MB NAND flash Ethernet: eTSEC1: Connected to Atheros AR8035 GETH PHY eTSEC2: Connected to Atheros AR8035 GETH PHY PCIe: Three mini-PCIe slots USB: Two USB2.0 Type A ports I2C: AT24C08 8K Board EEPROM (8 bit address) Signed-off-by:
Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by:
-
Haijun.Zhang authored
Add this file to help detect cpu type in runtime. These macros will be more favorable for driver to apply errata and workaround to specified cpu type. Signed-off-by:
Haijun Zhang <Haijun.Zhang@freescale.com> Signed-off-by:
Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by:
-
- 23 Aug, 2013 4 commits
-
-
Gerhard Sittig authored
prepare C preprocessor support when processing MPC512x DTS files - switch from DTS syntax to CPP syntax for include specs - create a symlink such that DTS processing can reference includes Signed-off-by:
Gerhard Sittig <gsi@denx.de> Signed-off-by:
Anatolij Gustschin <agust@denx.de>
-
Gerhard Sittig authored
reword the clock control module's registers declaration such that the MCLK related registers form an array and get indexed by PSC controller or CAN controller component number this change is in preparation to COMMON_CLK support for the MPC512x platform, the changed declaration remains neutral to existing code since the PSC and MSCAN CCR fields declared here aren't referenced elsewhere Signed-off-by:
-
Gerhard Sittig authored
use devm_clk_get() for automatic put after device close, check for and propagate errors when enabling clocks, need to prepare clocks before they can get enabled, adjust code paths to correctly balance get/put and prepare/unprepare and enable/disable calls Cc: Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by:
-
Gerhard Sittig authored
use devm_clk_get() for automatic put after device close, check for and propagate errors when enabling clocks, need to prepare clocks before they can get enabled, adjust error code paths to correctly balance get/put and prepare/unprepare and enable/disable calls Signed-off-by:
-
