ndo_stop() is RTNL-protected by net core, and the worker function takes
RTNL as well. Therefore we will deadlock when trying to execute a
pending work synchronously. To fix this execute any pending work
asynchronously. This will do no harm because netif_running() is false
in ndo_stop(), and therefore the work function is effectively a no-op.
However we have to ensure that no task is running or pending after
rtl_remove_one(), therefore add a call to cancel_work_sync().

Fixes: abe5fc42 ("r8169: use RTNL to protect critical sections")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/12395867-1d17-4cac-aa7d-c691938fcddf@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The original change results in a deadlock if jumbo mtu mode is used.
Reason is that the phydev lock is held when rtl_reset_work() is called
here, and rtl_jumbo_config() calls phy_start_aneg() which also tries
to acquire the phydev lock. Fix this by calling rtl_reset_work()
asynchronously.

Fixes: 621735f5 ("r8169: fix rare issue with broken rx after link-down on RTL8125")
Reported-by: Ian Chen <free122448@hotmail.com>
Tested-by: Ian Chen <free122448@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/caf6a487-ef8c-4570-88f9-f47a659faf33@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Previously, one-element and zero-length arrays were treated as true
flexible arrays, even though they are actually "fake" flex arrays.
The __randomize_layout would leave them untouched at the end of the
struct, similarly to proper C99 flex-array members.

However, this approach changed with commit 1ee60356 ("gcc-plugins:
randstruct: Only warn about true flexible arrays"). Now, only C99
flexible-array members will remain untouched at the end of the struct,
while one-element and zero-length arrays will be subject to randomization.

Fix a `__randomize_layout` crash in `struct neighbour` by transforming
zero-length array `primary_key` into a proper C99 flexible-array member.

Fixes: 1ee60356 ("gcc-plugins: randstruct: Only warn about true flexible arrays")
Closes: https://lore.kernel.org/linux-hardening/20231124102458.GB1503258@e124191.cambridge.arm.com/Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/ZWJoRsJGnCPdJ3+2@workSigned-off-by: Paolo Abeni <pabeni@redhat.com>

TC ingress policer rules depends on interface receive queue
contexts since the bandwidth profiles are attached to RQ
contexts. When an interface is brought down all the queue
contexts are freed. This in turn frees bandwidth profiles in
hardware causing ingress police rules non-functional after
the interface is brought up. Fix this by applying all the ingress
police rules config to hardware in otx2_open. Also allow
adding ingress rules only when interface is running
since no contexts exist for the interface when it is down.

Fixes: 68fbff68 ("octeontx2-pf: Add police action for TC flower")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930217-5707-1-git-send-email-sbhatta@marvell.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When more than 64 VFs are enabled for a PF then mbox communication
between VF and PF is not working as mbox work queueing for few VFs
are skipped due to wrong calculation of VF numbers.

Fixes: d424b6c0 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930042-5400-1-git-send-email-sbhatta@marvell.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Commit aeb18dd0 ("net: stmmac: xgmac: Disable MMC interrupts
by default") tries to disable MMC interrupts to avoid a storm of
unhandled interrupts, but leaves the FPE(Frame Preemption) MMC
interrupts enabled, FPE MMC interrupts can cause the same problem.
Now we mask FPE TX and RX interrupts to disable all MMC interrupts.

Fixes: aeb18dd0 ("net: stmmac: xgmac: Disable MMC interrupts by default")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231125060126.2328690-1-0x1207@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

A loop in rvu_mbox_handler_nix_bandprof_free() contains
a break if (idx == MAX_BANDPROF_PER_PFFUNC),
but if idx may reach MAX_BANDPROF_PER_PFFUNC
buffer '(*req->prof_idx)[layer]' overflow happens before that check.

The patch moves the break to the
beginning of the loop.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: e8e095b3 ("octeontx2-af: cn10k: Bandwidth profiles config support").
Signed-off-by: Elena Salomatkina <elena.salomatkina.cmc@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20231124210802.109763-1-elena.salomatkina.cmc@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Willem de Bruijn says:

====================
selftests/net: fix a few small compiler warnings

Observed a clang warning when backporting cmsg_sender.
Ran the same build against all the .c files under selftests/net.

This is clang-14 with -Wall
Which is what tools/testing/selftests/net/Makefile also enables.
====================

Link: https://lore.kernel.org/r/20231124171645.1011043-1-willemdebruijn.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Same init_rng() in both tests. The function reads /dev/urandom to
initialize srand(). In case of failure, it falls back onto the
entropy in the uninitialized variable. Not sure if this is on purpose.
But failure reading urandom should be rare, so just fail hard. While
at it, convert to getrandom(). Which man 4 random suggests is simpler
and more robust.

    mptcp_inq.c:525:6:
    mptcp_connect.c:1131:6:

    error: variable 'foo' is used uninitialized
    whenever 'if' condition is false
    [-Werror,-Wsometimes-uninitialized]

Fixes: 048d19d4 ("mptcp: add basic kselftest for mptcp")
Fixes: b5188056 ("selftests: mptcp: add inq test case")
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Willem de Bruijn <willemb@google.com>

----

When input is randomized because this is expected to meaningfully
explore edge cases, should we also add
1. logging the random seed to stdout and
2. adding a command line argument to replay from a specific seed
I can do this in net-next, if authors find it useful in this case.
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>

Link: https://lore.kernel.org/r/20231124171645.1011043-5-willemdebruijn.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Remove an unused variable.

    diag_uid.c:151:24:
    error: unused variable 'udr'
    [-Werror,-Wunused-variable]

Fixes: ac011361 ("af_unix: Add test for sock_diag and UDIAG_SHOW_UID.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20231124171645.1011043-4-willemdebruijn.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Signedness of char is signed on x86_64, but unsigned on arm64.

Fix the warning building cmsg_sender.c on signed platforms or
forced with -fsigned-char:

    msg_sender.c:455:12:
    error: implicit conversion from 'int' to 'char'
    changes value from 128 to -128
    [-Werror,-Wconstant-conversion]
        buf[0] = ICMPV6_ECHO_REQUEST;

constant ICMPV6_ECHO_REQUEST is 128.

Link: https://lwn.net/Articles/911914
Fixes: de17e305 ("selftests: net: cmsg_sender: support icmp and raw sockets")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20231124171645.1011043-3-willemdebruijn.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix a small compiler warning.

nr_process must be a signed long: it is assigned a signed long by
strtol() and is compared against LONG_MIN and LONG_MAX.

ipsec.c:2280:65:
    error: result of comparison of constant -9223372036854775808
    with expression of type 'unsigned int' is always false
    [-Werror,-Wtautological-constant-out-of-range-compare]

  if ((errno == ERANGE && (nr_process == LONG_MAX || nr_process == LONG_MIN))

Fixes: bc2652b7 ("selftest/net/xfrm: Add test for ipsec tunnel")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20231124171645.1011043-2-willemdebruijn.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Ioana Ciornei says:

====================
dpaa2-eth: various fixes

The first patch fixes a memory corruption issue happening between the Tx
and Tx confirmation of a packet by making the Tx alignment at 64bytes
mandatory instead of optional as it was previously.

The second patch fixes the Rx copybreak code path which recycled the
initial data buffer before all processing was done on the packet.

Changes in v2:
- squashed patches #1 and #2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The blamed commit added support for Rx copybreak. This meant that for
certain frame sizes, a new skb was allocated and the initial data buffer
was recycled. Instead of waiting to recycle the Rx buffer only after all
processing was done on it (like accessing the parse results or timestamp
information), the code path just went ahead and re-used the buffer right
away.

This sometimes lead to corrupted HW and SW annotation areas.
Fix this by delaying the moment when the buffer is recycled.

Fixes: 50f82699 ("dpaa2-eth: add rx copybreak support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Increase the needed headroom to account for a 64 byte alignment
restriction which, with this patch, we make mandatory on the Tx path.
The case in which the amount of headroom needed is not available is
already handled by the driver which instead sends a S/G frame with the
first buffer only holding the SW and HW annotation areas.

Without this patch, we can empirically see data corruption happening
between Tx and Tx confirmation which sometimes leads to the SW
annotation area being overwritten.

Since this is an old IP where the hardware team cannot help to
understand the underlying behavior, we make the Tx alignment mandatory
for all frames to avoid the crash on Tx conf. Also, remove the comment
that suggested that this is just an optimization.

This patch also sets the needed_headroom net device field to the usual
value that the driver would need on the Tx path:
	- 64 bytes for the software annotation area
	- 64 bytes to account for a 64 byte aligned buffer address

Fixes: 6e2387e8 ("staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver")
Closes: https://lore.kernel.org/netdev/aa784d0c-85eb-4e5d-968b-c8f74fa86be6@gin.de/Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As of commit b92143d4 ("net: dsa: mv88e6xxx: add infrastructure for
phylink_pcs") probing of a Marvell 88e6350 switch causes a NULL pointer
de-reference like this example:

    ...
    mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
    8<--- cut here ---
    Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read
    [00000000] *pgd=00000000
    Internal error: Oops: 5 [#1] ARM
    Modules linked in:
    CPU: 0 PID: 8 Comm: kworker/u2:0 Not tainted 6.7.0-rc2-dirty #26
    Hardware name: Marvell Armada 370/XP (Device Tree)
    Workqueue: events_unbound deferred_probe_work_func
    PC is at mv88e6xxx_port_setup+0x1c/0x44
    LR is at dsa_port_devlink_setup+0x74/0x154
    pc : [<c057ea24>]    lr : [<c0819598>]    psr: a0000013
    sp : c184fce0  ip : c542b8f4  fp : 00000000
    r10: 00000001  r9 : c542a540  r8 : c542bc00
    r7 : c542b838  r6 : c5244580  r5 : 00000005  r4 : c5244580
    r3 : 00000000  r2 : c542b840  r1 : 00000005  r0 : c1a02040
    ...

The Marvell 6350 switch has no SERDES interface and so has no
corresponding pcs_ops defined for it. But during probing a call is made
to mv88e6xxx_port_setup() which unconditionally expects pcs_ops to exist -
though the presence of the pcs_ops->pcs_init function is optional.

Modify code to check for pcs_ops first, before checking for and calling
pcs_ops->pcs_init. Modify checking and use of pcs_ops->pcs_teardown
which may potentially suffer the same problem.

Fixes: b92143d4 ("net: dsa: mv88e6xxx: add infrastructure for phylink_pcs")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

As of commit de5c9bf4 ("net: phylink: require supported_interfaces to
be filled") Marvell 88e6350 switches fail to be probed:

    ...
    mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
    mv88e6085 d0072004.mdio-mii:11: phylink: error: empty supported_interfaces
    error creating PHYLINK: -22
    mv88e6085: probe of d0072004.mdio-mii:11 failed with error -22
    ...

The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities. Create a new dedicated phylink_get_caps for the
6351 family (which the 6350 is one of) to properly support their set of
capabilities.

According to chip.h the 6351 switch family includes the 6171, 6175, 6350
and 6351 switches, so update each of these to use the correct
phylink_get_caps.

Fixes: de5c9bf4 ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When I perform the following test operations:
1.ip link add br0 type bridge
2.brctl addif br0 eth0
3.ip addr add 239.0.0.1/32 dev eth0
4.ip addr add 239.0.0.1/32 dev br0
5.ip addr add 224.0.0.1/32 dev br0
6.while ((1))
    do
        ifconfig br0 up
        ifconfig br0 down
    done
7.send IGMPv2 query packets to port eth0 continuously. For example,
./mausezahn ethX -c 0 "01 00 5e 00 00 01 00 72 19 88 aa 02 08 00 45 00 00
1c 00 01 00 00 01 02 0e 7f c0 a8 0a b7 e0 00 00 01 11 64 ee 9b 00 00 00 00"

The preceding tests may trigger the refcnt uaf issue of the mc list. The
stack is as follows:
	refcount_t: addition on 0; use-after-free.
	WARNING: CPU: 21 PID: 144 at lib/refcount.c:25 refcount_warn_saturate (lib/refcount.c:25)
	CPU: 21 PID: 144 Comm: ksoftirqd/21 Kdump: loaded Not tainted 6.7.0-rc1-next-20231117-dirty #80
	Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
	RIP: 0010:refcount_warn_saturate (lib/refcount.c:25)
	RSP: 0018:ffffb68f00657910 EFLAGS: 00010286
	RAX: 0000000000000000 RBX: ffff8a00c3bf96c0 RCX: ffff8a07b6160908
	RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ffff8a07b6160900
	RBP: ffff8a00cba36862 R08: 0000000000000000 R09: 00000000ffff7fff
	R10: ffffb68f006577c0 R11: ffffffffb0fdcdc8 R12: ffff8a00c3bf9680
	R13: ffff8a00c3bf96f0 R14: 0000000000000000 R15: ffff8a00d8766e00
	FS:  0000000000000000(0000) GS:ffff8a07b6140000(0000) knlGS:0000000000000000
	CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
	CR2: 000055f10b520b28 CR3: 000000039741a000 CR4: 00000000000006f0
	Call Trace:
	<TASK>
	igmp_heard_query (net/ipv4/igmp.c:1068)
	igmp_rcv (net/ipv4/igmp.c:1132)
	ip_protocol_deliver_rcu (net/ipv4/ip_input.c:205)
	ip_local_deliver_finish (net/ipv4/ip_input.c:234)
	__netif_receive_skb_one_core (net/core/dev.c:5529)
	netif_receive_skb_internal (net/core/dev.c:5729)
	netif_receive_skb (net/core/dev.c:5788)
	br_handle_frame_finish (net/bridge/br_input.c:216)
	nf_hook_bridge_pre (net/bridge/br_input.c:294)
	__netif_receive_skb_core (net/core/dev.c:5423)
	__netif_receive_skb_list_core (net/core/dev.c:5606)
	__netif_receive_skb_list (net/core/dev.c:5674)
	netif_receive_skb_list_internal (net/core/dev.c:5764)
	napi_gro_receive (net/core/gro.c:609)
	e1000_clean_rx_irq (drivers/net/ethernet/intel/e1000/e1000_main.c:4467)
	e1000_clean (drivers/net/ethernet/intel/e1000/e1000_main.c:3805)
	__napi_poll (net/core/dev.c:6533)
	net_rx_action (net/core/dev.c:6735)
	__do_softirq (kernel/softirq.c:554)
	run_ksoftirqd (kernel/softirq.c:913)
	smpboot_thread_fn (kernel/smpboot.c:164)
	kthread (kernel/kthread.c:388)
	ret_from_fork (arch/x86/kernel/process.c:153)
	ret_from_fork_asm (arch/x86/entry/entry_64.S:250)
	</TASK>

The root causes are as follows:
Thread A					Thread B
...						netif_receive_skb
br_dev_stop					...
    br_multicast_leave_snoopers			...
        __ip_mc_dec_group			...
            __igmp_group_dropped		igmp_rcv
                igmp_stop_timer			    igmp_heard_query         //ref = 1
                ip_ma_put			        igmp_mod_timer
                    refcount_dec_and_test	            igmp_start_timer //ref = 0
			...                                     refcount_inc //ref increases from 0
When the device receives an IGMPv2 Query message, it starts the timer
immediately, regardless of whether the device is running. If the device is
down and has left the multicast group, it will cause the mc list refcount
uaf issue.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added initialization use_ack to mptcp_parse_option().

Reported-by: syzbot+b834a6b2decad004cfa1@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yoshihiro Shimoda says:

====================
net: rswitch: Fix issues in rswitch_start_xmit()

This patch series is based on the latest net.git / main branch.

Changes from v2:
https://lore.kernel.org/all/20231122012556.3645840-1-yoshihiro.shimoda.uh@renesas.com/
- Keep reverse christmas tree of local variable declarations in patch 1/3.

Changes from v1:
https://lore.kernel.org/all/20231121055255.3627949-1-yoshihiro.shimoda.uh@renesas.com/
- Separate a patch because fixing 2 issues.
- Add fixing wrong type of return value.
- Use goto for improving code readability.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Before returning the rswitch_start_xmit() in the error path,
dev_kfree_skb_any() should be called. So, fix it.

Fixes: 33f5d733 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This .ndo_start_xmit() function should return netdev_tx_t value,
not -ENOMEM. So, fix it.

Fixes: 33f5d733 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The type of ret in rswitch_start_xmit() should be netdev_tx_t. So,
fix it.

Fixes: 3590918b ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf.

  Current release - regressions:

   - Revert "net: r8169: Disable multicast filter for RTL8168H and
     RTL8107E"

   - kselftest: rtnetlink: fix ip route command typo

  Current release - new code bugs:

   - s390/ism: make sure ism driver implies smc protocol in kconfig

   - two build fixes for tools/net

  Previous releases - regressions:

   - rxrpc: couple of ACK/PING/RTT handling fixes

  Previous releases - always broken:

   - bpf: verify bpf_loop() callbacks as if they are called unknown
     number of times

   - improve stability of auto-bonding with Hyper-V

   - account BPF-neigh-redirected traffic in interface statistics

  Misc:

   - net: fill in some more MODULE_DESCRIPTION()s"

* tag 'net-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
  tools: ynl: fix duplicate op name in devlink
  tools: ynl: fix header path for nfsd
  net: ipa: fix one GSI register field width
  tls: fix NULL deref on tls_sw_splice_eof() with empty record
  net: axienet: Fix check for partial TX checksum
  vsock/test: fix SEQPACKET message bounds test
  i40e: Fix adding unsupported cloud filters
  ice: restore timestamp configuration after device reset
  ice: unify logic for programming PFINT_TSYN_MSK
  ice: remove ptp_tx ring parameter flag
  amd-xgbe: propagate the correct speed and duplex status
  amd-xgbe: handle the corner-case during tx completion
  amd-xgbe: handle corner-case during sfp hotplug
  net: veth: fix ethtool stats reporting
  octeontx2-pf: Fix ntuple rule creation to direct packet to VF with higher Rx queue than its PF
  net: usb: qmi_wwan: claim interface 4 for ZTE MF290
  Revert "net: r8169: Disable multicast filter for RTL8168H and RTL8107E"
  net/smc: avoid data corruption caused by decline
  nfc: virtual_ncidev: Add variable to check if ndev is running
  dpll: Fix potential msg memleak when genlmsg_put_reply failed
  ...

We don't support CRUD-inspired message types in YNL too well.
One aspect that currently trips us up is the fact that single
message ID can be used in multiple commands (as the response).
This leads to duplicate entries in the id-to-string tables:

devlink-user.c:19:34: warning: initialized field overwritten [-Woverride-init]
   19 |         [DEVLINK_CMD_PORT_NEW] = "port-new",
      |                                  ^~~~~~~~~~
devlink-user.c:19:34: note: (near initialization for ‘devlink_op_strmap[7]’)

Fixes tag points at where the code was generated, the "real" problem
is that the code generator does not support CRUD.

Fixes: f2f9dd16 ("netlink: specs: devlink: add the remaining command to generate complete split_ops")
Link: https://lore.kernel.org/r/20231123030558.1611831-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The makefile dependency is trying to include the wrong header:

<command-line>: fatal error: ../../../../include/uapi//linux/nfsd.h: No such file or directory

The guard also looks wrong.

Fixes: f14122b2 ("tools: ynl: Add source files for nfsd netlink protocol")
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://lore.kernel.org/r/20231123030624.1611925-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The width of the R_LENGTH field of the EV_CH_E_CNTXT_1 GSI register
is 24 bits (not 20 bits) starting with IPA v5.0.  Fix this.

Fixes: faf0678e ("net: ipa: add IPA v5.0 GSI register definitions")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20231122231708.896632-1-elder@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzkaller discovered that if tls_sw_splice_eof() is executed as part of
sendfile() when the plaintext/ciphertext sk_msg are empty, the send path
gets confused because the empty ciphertext buffer does not have enough
space for the encryption overhead. This causes tls_push_record() to go on
the `split = true` path (which is only supposed to be used when interacting
with an attached BPF program), and then get further confused and hit the
tls_merge_open_record() path, which then assumes that there must be at
least one populated buffer element, leading to a NULL deref.

It is possible to have empty plaintext/ciphertext buffers if we previously
bailed from tls_sw_sendmsg_locked() via the tls_trim_both_msgs() path.
tls_sw_push_pending_record() already handles this case correctly; let's do
the same check in tls_sw_splice_eof().

Fixes: df720d28 ("tls/sw: Use splice_eof() to flush")
Cc: stable@vger.kernel.org
Reported-by: syzbot+40d43509a099ea756317@syzkaller.appspotmail.com
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20231122214447.675768-1-jannh@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Due to a typo, the code checked the RX checksum feature in the TX path.

Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20231122004219.3504219-1-samuel.holland@sifive.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tune message length calculation to make this test work on machines
where 'getpagesize()' returns >32KB. Now maximum message length is not
hardcoded (on machines above it was smaller than 'getpagesize()' return
value, thus we get negative value and test fails), but calculated at
runtime and always bigger than 'getpagesize()' result. Reproduced on
aarch64 with 64KB page size.

Fixes: 5c338112 ("test/vsock: rework message bounds test")
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reported-by: Bogdan Marcynkov <bmarcynk@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20231121211642.163474-1-avkrasnov@salutedevices.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If a VF tries to add unsupported cloud filter through virtchnl
then i40e_add_del_cloud_filter(_big_buf) returns -ENOTSUPP but
this error code is stored in 'ret' instead of 'aq_ret' that
is used as error code sent back to VF. In this scenario where
one of the mentioned functions fails the value of 'aq_ret'
is zero so the VF will incorrectly receive a 'success'.

Use 'aq_ret' to store return value and remove 'ret' local
variable. Additionally fix the issue when filter allocation
fails, in this case no notification is sent back to the VF.

Fixes: e284fc28 ("i40e: Add and delete cloud filter")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231121211338.3348677-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
ice: restore timestamp config after reset

Jake Keller says:

We recently discovered during internal validation that the ice driver has
not been properly restoring Tx timestamp configuration after a device reset,
which resulted in application failures after a device reset.

After some digging, it turned out this problem is two-fold. Since the
introduction of the PTP support the driver has been clobbering the storage
of the current timestamp configuration during reset. Thus after a reset, the
driver will no longer perform Tx or Rx timestamps, and will report
timestamp configuration as disabled if SIOCGHWTSTAMP ioctl is issued.

In addition, the recently merged auxiliary bus support code missed that
PFINT_TSYN_MSK must be reprogrammed on the clock owner for E822 devices.
Failure to restore this register configuration results in the driver no
longer responding to interrupts from other ports. Depending on the traffic
pattern, this can either result in increased latency responding to
timestamps on the non-owner ports, or it can result in the driver never
reporting any timestamps. The configuration of PFINT_TSYN_MSK was only done
during initialization. Due to this, the Tx timestamp issue persists even if
userspace reconfigures timestamping.

This series fixes both issues, as well as removes a redundant Tx ring field
since we can rely on the skb flag as the primary detector for a Tx timestamp
request.

Note that I don't think this series will directly apply to older stable
releases (even v6.6) as we recently refactored a lot of the PTP code to
support auxiliary bus. Patch 2/3 only matters for the post-auxiliary bus
implementation. The principle of patch 1/3 and 3/3 could apply as far back
as the initial PTP support, but I don't think it will apply cleanly as-is.
====================

Link: https://lore.kernel.org/r/20231121211259.3348630-1-anthony.l.nguyen@intel.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The driver calls ice_ptp_cfg_timestamp() during ice_ptp_prepare_for_reset()
to disable timestamping while the device is resetting. This operation
destroys the user requested configuration. While the driver does call
ice_ptp_cfg_timestamp in ice_rebuild() to restore some hardware settings
after a reset, it unconditionally passes true or false, resulting in
failure to restore previous user space configuration.

This results in a device reset forcibly disabling timestamp configuration
regardless of current user settings.

This was not detected previously due to a quirk of the LinuxPTP ptp4l
application. If ptp4l detects a missing timestamp, it enters a fault state
and performs recovery logic which includes executing SIOCSHWTSTAMP again,
restoring the now accidentally cleared configuration.

Not every application does this, and for these applications, timestamps
will mysteriously stop after a PF reset, without being restored until an
application restart.

Fix this by replacing ice_ptp_cfg_timestamp() with two new functions:

1) ice_ptp_disable_timestamp_mode() which unconditionally disables the
   timestamping logic in ice_ptp_prepare_for_reset() and ice_ptp_release()

2) ice_ptp_restore_timestamp_mode() which calls
   ice_ptp_restore_tx_interrupt() to restore Tx timestamping configuration,
   calls ice_set_rx_tstamp() to restore Rx timestamping configuration, and
   issues an immediate TSYN_TX interrupt to ensure that timestamps which
   may have occurred during the device reset get processed.

Modify the ice_ptp_set_timestamp_mode to directly save the user
configuration and then call ice_ptp_restore_timestamp_mode. This way, reset
no longer destroys the saved user configuration.

This obsoletes the ice_set_tx_tstamp() function which can now be safely
removed.

With this change, all devices should now restore Tx and Rx timestamping
functionality correctly after a PF reset without application intervention.

Fixes: 77a78115 ("ice: enable receive hardware timestamping")
Fixes: ea9b847c ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Commit d938a8cc ("ice: Auxbus devices & driver for E822 TS") modified
how Tx timestamps are handled for E822 devices. On these devices, only the
clock owner handles reading the Tx timestamp data from firmware. To do
this, the PFINT_TSYN_MSK register is modified from the default value to one
which enables reacting to a Tx timestamp on all PHY ports.

The driver currently programs PFINT_TSYN_MSK in different places depending
on whether the port is the clock owner or not. For the clock owner, the
PFINT_TSYN_MSK value is programmed during ice_ptp_init_owner just before
calling ice_ptp_tx_ena_intr to program the PHY ports.

For the non-clock owner ports, the PFINT_TSYN_MSK is programmed during
ice_ptp_init_port.

If a large enough device reset occurs, the PFINT_TSYN_MSK register will be
reset to the default value in which only the PHY associated directly with
the PF will cause the Tx timestamp interrupt to trigger.

The driver lacks logic to reprogram the PFINT_TSYN_MSK register after a
device reset. For the E822 device, this results in the PF no longer
responding to interrupts for other ports. This results in failure to
deliver Tx timestamps to user space applications.

Rename ice_ptp_configure_tx_tstamp to ice_ptp_cfg_tx_interrupt, and unify
the logic for programming PFINT_TSYN_MSK and PFINT_OICR_ENA into one place.
This function will program both registers according to the combination of
user configuration and device requirements.

This ensures that PFINT_TSYN_MSK is always restored when we configure the
Tx timestamp interrupt.

Fixes: d938a8cc ("ice: Auxbus devices & driver for E822 TS")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Before performing a Tx timestamp in ice_stamp(), the driver checks a ptp_tx
ring variable to see if timestamping is enabled on that ring. This value is
set for all rings whenever userspace configures Tx timestamping.

Ostensibly this was done to avoid wasting cycles checking other fields when
timestamping has not been enabled. However, for Tx timestamps we already
get an individual per-SKB flag indicating whether userspace wants to
request a timestamp on that packet. We do not gain much by also having
a separate flag to check for whether timestamping was enabled.

In fact, the driver currently fails to restore the field after a PF reset.
Because of this, if a PF reset occurs, timestamps will be disabled.

Since this flag doesn't add value in the hotpath, remove it and always
provide a timestamp if the SKB flag has been set.

A following change will fix the reset path to properly restore user
timestamping configuration completely.

This went unnoticed for some time because one of the most common
applications using Tx timestamps, ptp4l, will reconfigure the socket as
part of its fault recovery logic.

Fixes: ea9b847c ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Raju Rangoju says:

====================
amd-xgbe: fixes to handle corner-cases

This series include bug fixes to amd-xgbe driver.
====================

Link: https://lore.kernel.org/r/20231121191435.4049995-1-Raju.Rangoju@amd.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.

Address this by propagating correct information.

Fixes: 7c12aa08 ("amd-xgbe: Move the PHY support into amd-xgbe")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.

To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.

Fixes: c5aa9e3b ("amd-xgbe: Initial AMD 10GbE platform driver")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.

Fixes: e57f7a3f ("amd-xgbe: Prepare for working with more than one type of phy")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Fix a possible misalignment between page_pool stats and tx xdp_stats
reported in veth_get_ethtool_stats routine.
The issue can be reproduced configuring the veth pair with the
following tx/rx queues:

$ip link add v0 numtxqueues 2 numrxqueues 4 type veth peer name v1 \
 numtxqueues 1 numrxqueues 1

and loading a simple XDP program on v0 that just returns XDP_PASS.
In this case on v0 the page_pool stats overwrites tx xdp_stats for queue 1.
Fix the issue incrementing pp_idx of dev->real_num_tx_queues * VETH_TQ_STATS_LEN
since we always report xdp_stats for all tx queues in ethtool.

Fixes: 4fc41805 ("net: veth: add page_pool stats")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c5b5d0485016836448453f12846c7c4ab75b094a.1700593593.git.lorenzo@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>