- 28 Jan, 2021 13 commits
-
-
Jakub Kicinski authored
Ido Schimmel says: ==================== mlxsw: Various fixes Patch #1 fixes wrong invocation of mausezahn in a couple of selftests. The tests started failing after Fedora updated their libnet package from version 1.1.6 to 1.2.1. With the fix the tests pass regardless of libnet version. Patch #2 fixes an issue in the mirroring to CPU code that results in policer configuration being overwritten. ==================== Link: https://lore.kernel.org/r/20210128144820.3280295-1-idosch@idosch.orgSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Ido Schimmel authored
The purpose of the delayed work in the SPAN module is to potentially update the destination port and various encapsulation parameters of SPAN agents that point to a VLAN device or a GRE tap. The destination port can change following the insertion of a new route, for example. SPAN agents that point to a physical port or the CPU port are static and never change throughout the lifetime of the SPAN agent. Therefore, skip over them in the delayed work. This fixes an issue where the delayed work overwrites the policer that was set on a SPAN agent pointing to the CPU. Modifying the delayed work to inherit the original policer configuration is error-prone, as the same will be needed for any new parameter. Fixes: 4039504e ("mlxsw: spectrum_span: Allow setting policer on a SPAN agent") Reviewed-by:
Petr Machata <petrm@nvidia.com> Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
-
Danielle Ratson authored
Specify the interface through which packets should be transmitted so that the test will pass regardless of the libnet version against which mausezahn is linked. Fixes: cab14d10 ("selftests: Add version of router_multipath.sh using nexthop objects") Fixes: 3d578d87 ("selftests: forwarding: Test IPv4 weighted nexthops") Signed-off-by:
Danielle Ratson <danieller@nvidia.com> Signed-off-by:
-
Voon Weifeng authored
Fix an issue where dump stack is printed and Reset Adapter occurs when PSE0 GbE or/and PSE1 GbE is/are enabled. EHL PSE0 GbE and PSE1 GbE use 32 bits DMA addressing whereas EHL PCH GbE uses 64 bits DMA addressing. [ 25.535095] ------------[ cut here ]------------ [ 25.540276] NETDEV WATCHDOG: enp0s29f2 (intel-eth-pci): transmit queue 2 timed out [ 25.548749] WARNING: CPU: 2 PID: 0 at net/sched/sch_generic.c:443 dev_watchdog+0x259/0x260 [ 25.558004] Modules linked in: 8021q bnep bluetooth ecryptfs snd_hda_codec_hdmi intel_gpy marvell intel_ishtp_loader intel_ishtp_hid iTCO_wdt mei_hdcp iTCO_vendor_support x86_pkg_temp_thermal kvm_intel dwmac_intel stmmac kvm igb pcs_xpcs irqbypass phylink snd_hda_intel intel_rapl_msr pcspkr dca snd_hda_codec i915 i2c_i801 i2c_smbus libphy intel_ish_ipc snd_hda_core mei_me intel_ishtp mei spi_dw_pci 8250_lpss spi_dw thermal dw_dmac_core parport_pc tpm_crb tpm_tis parport tpm_tis_core tpm intel_pmc_core sch_fq_codel uhid fuse configfs snd_sof_pci snd_sof_intel_byt snd_sof_intel_ipc snd_sof_intel_hda_common snd_sof_xtensa_dsp snd_sof snd_soc_acpi_intel_match snd_soc_acpi snd_intel_dspcfg ledtrig_audio snd_soc_core snd_compress ac97_bus snd_pcm snd_timer snd soundcore [ 25.633795] CPU: 2 PID: 0 Comm: swapper/2 Tainted: G U 5.11.0-rc4-intel-lts-MISMAIL5+ #5 [ 25.644306] Hardware name: Intel Corporation Elkhart Lake Embedded Platform/ElkhartLake LPDDR4x T4 RVP1, BIOS EHLSFWI1.R00.2434.A00.2010231402 10/23/2020 [ 25.659674] RIP: 0010:dev_watchdog+0x259/0x260 [ 25.664650] Code: e8 3b 6b 60 ff eb 98 4c 89 ef c6 05 ec e7 bf 00 01 e8 fb e5 fa ff 89 d9 4c 89 ee 48 c7 c7 78 31 d2 9e 48 89 c2 e8 79 1b 18 00 <0f> 0b e9 77 ff ff ff 0f 1f 44 00 00 48 c7 47 08 00 00 00 00 48 c7 [ 25.685647] RSP: 0018:ffffb7ca80160eb8 EFLAGS: 00010286 [ 25.691498] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000103 [ 25.699483] RDX: 0000000080000103 RSI: 00000000000000f6 RDI: 00000000ffffffff [ 25.707465] RBP: ffff985709ce0440 R08: 0000000000000000 R09: c0000000ffffefff [ 25.715455] R10: ffffb7ca80160cf0 R11: ffffb7ca80160ce8 R12: ffff985709ce039c [ 25.723438] R13: ffff985709ce0000 R14: 0000000000000008 R15: ffff9857068af940 [ 25.731425] FS: 0000000000000000(0000) GS:ffff985864300000(0000) knlGS:0000000000000000 [ 25.740481] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 25.746913] CR2: 00005567f8bb76b8 CR3: 00000001f8e0a000 CR4: 0000000000350ee0 [ 25.754900] Call Trace: [ 25.757631] <IRQ> [ 25.759891] ? qdisc_put_unlocked+0x30/0x30 [ 25.764565] ? qdisc_put_unlocked+0x30/0x30 [ 25.769245] call_timer_fn+0x2e/0x140 [ 25.773346] run_timer_softirq+0x1f3/0x430 [ 25.777932] ? __hrtimer_run_queues+0x12c/0x2c0 [ 25.783005] ? ktime_get+0x3e/0xa0 [ 25.786812] __do_softirq+0xa6/0x2ef [ 25.790816] asm_call_irq_on_stack+0xf/0x20 [ 25.795501] </IRQ> [ 25.797852] do_softirq_own_stack+0x5d/0x80 [ 25.802538] irq_exit_rcu+0x94/0xb0 [ 25.806475] sysvec_apic_timer_interrupt+0x42/0xc0 [ 25.811836] asm_sysvec_apic_timer_interrupt+0x12/0x20 [ 25.817586] RIP: 0010:cpuidle_enter_state+0xd9/0x370 [ 25.823142] Code: 85 c0 0f 8f 0a 02 00 00 31 ff e8 22 d5 7e ff 45 84 ff 74 12 9c 58 f6 c4 02 0f 85 47 02 00 00 31 ff e8 7b a0 84 ff fb 45 85 f6 <0f> 88 ab 00 00 00 49 63 ce 48 2b 2c 24 48 89 c8 48 6b d1 68 48 c1 [ 25.844140] RSP: 0018:ffffb7ca800f7e80 EFLAGS: 00000206 [ 25.849996] RAX: ffff985864300000 RBX: 0000000000000003 RCX: 000000000000001f [ 25.857975] RDX: 00000005f2028ea8 RSI: ffffffff9ec5907f RDI: ffffffff9ec62a5d [ 25.865961] RBP: 00000005f2028ea8 R08: 0000000000000000 R09: 0000000000029d00 [ 25.873947] R10: 000000137b0e0508 R11: ffff9858643294e4 R12: ffff9858643336d0 [ 25.881935] R13: ffffffff9ef74b00 R14: 0000000000000003 R15: 0000000000000000 [ 25.889918] cpuidle_enter+0x29/0x40 [ 25.893922] do_idle+0x24a/0x290 [ 25.897536] cpu_startup_entry+0x19/0x20 [ 25.901930] start_secondary+0x128/0x160 [ 25.906326] secondary_startup_64_no_verify+0xb0/0xbb [ 25.911983] ---[ end trace b4c0c8195d0ba61f ]--- [ 25.917193] intel-eth-pci 0000:00:1d.2 enp0s29f2: Reset adapter. Fixes: 67c08ac4 ("net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID") Signed-off-by:
Voon Weifeng <weifeng.voon@intel.com> Co-developed-by:
Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Signed-off-by:
-
Giacinto Cifelli authored
lsusb -v for this device: Bus 003 Device 007: ID 1e2d:0069 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 239 Miscellaneous Device bDeviceSubClass 2 ? bDeviceProtocol 1 Interface Association bMaxPacketSize0 64 idVendor 0x1e2d idProduct 0x0069 bcdDevice 0.00 iManufacturer 4 Cinterion Wireless Modules iProduct 3 PLSx3 iSerial 5 fa3c1419 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 352 bNumInterfaces 10 bConfigurationValue 1 iConfiguration 2 Cinterion Configuration bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 500mA Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 0 bInterfaceCount 2 bFunctionClass 2 Communications bFunctionSubClass 2 Abstract (modem) bFunctionProtocol 1 AT-commands (v.25ter) iFunction 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 CDC Header: bcdCDC 1.10 CDC ACM: bmCapabilities 0x02 line coding and serial state CDC Call Management: bmCapabilities 0x03 call management use DataInterface bDataInterface 1 CDC Union: bMasterInterface 0 bSlaveInterface 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 2 bInterfaceCount 2 bFunctionClass 2 Communications bFunctionSubClass 2 Abstract (modem) bFunctionProtocol 1 AT-commands (v.25ter) iFunction 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 CDC Header: bcdCDC 1.10 CDC ACM: bmCapabilities 0x02 line coding and serial state CDC Call Management: bmCapabilities 0x03 call management use DataInterface bDataInterface 3 CDC Union: bMasterInterface 2 bSlaveInterface 3 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 3 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x84 EP 4 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 4 bInterfaceCount 2 bFunctionClass 2 Communications bFunctionSubClass 2 Abstract (modem) bFunctionProtocol 1 AT-commands (v.25ter) iFunction 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 4 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 CDC Header: bcdCDC 1.10 CDC ACM: bmCapabilities 0x02 line coding and serial state CDC Call Management: bmCapabilities 0x03 call management use DataInterface bDataInterface 5 CDC Union: bMasterInterface 4 bSlaveInterface 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 5 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 6 bInterfaceCount 2 bFunctionClass 2 Communications bFunctionSubClass 2 Abstract (modem) bFunctionProtocol 1 AT-commands (v.25ter) iFunction 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 6 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 CDC Header: bcdCDC 1.10 CDC ACM: bmCapabilities 0x02 line coding and serial state CDC Call Management: bmCapabilities 0x03 call management use DataInterface bDataInterface 7 CDC Union: bMasterInterface 6 bSlaveInterface 7 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x87 EP 7 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 7 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x88 EP 8 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 8 bInterfaceCount 2 bFunctionClass 2 Communications bFunctionSubClass 0 bFunctionProtocol 0 iFunction 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 8 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 6 Ethernet Networking bInterfaceProtocol 0 iInterface 0 CDC Header: bcdCDC 1.10 CDC Ethernet: iMacAddress 1 00A0C6C14190 bmEthernetStatistics 0x00000000 wMaxSegmentSize 16384 wNumberMCFilters 0x0001 bNumberPowerFilters 0 CDC Union: bMasterInterface 8 bSlaveInterface 9 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x89 EP 9 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 9 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 9 bAlternateSetting 1 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x8a EP 10 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 239 Miscellaneous Device bDeviceSubClass 2 ? bDeviceProtocol 1 Interface Association bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) Signed-off-by:Giacinto Cifelli <gciofono@gmail.com> Link: https://lore.kernel.org/r/20210126044245.8455-1-gciofono@gmail.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxJakub Kicinski authored
Saeed Mahameed says: ==================== mlx5 fixes 2021-01-26 This series introduces some fixes to mlx5 driver. * tag 'mlx5-fixes-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5: CT: Fix incorrect removal of tuple_nat_node from nat rhashtable net/mlx5e: Revert parameters on errors when changing MTU and LRO state without reset net/mlx5e: Revert parameters on errors when changing trust state without reset net/mlx5e: Correctly handle changing the number of queues when the interface is down net/mlx5e: Fix CT rule + encap slow path offload and deletion net/mlx5e: Disable hw-tc-offload when MLX5_CLS_ACT config is disabled net/mlx5: Maintain separate page trees for ECPF and PF functions net/mlx5e: Fix IPSEC stats net/mlx5e: Reduce tc unsupported key print level net/mlx5e: free page before return net/mlx5e: E-switch, Fix rate calculation for overflow net/mlx5: Fix memory leak on flow table creation error flow ==================== Link: https://lore.kernel.org/r/20210126234345.202096-1-saeedm@nvidia.comSigned-off-by:
-
Lijun Pan authored
Ensure that received Command-Response Queue (CRQ) entries are properly read in order by the driver. dma_rmb barrier has been added before accessing the CRQ descriptor to ensure the entire descriptor is read before processing. Fixes: 032c5e82 ("Driver for IBM System i/p VNIC protocol") Signed-off-by:
Lijun Pan <ljp@linux.ibm.com> Link: https://lore.kernel.org/r/20210128013442.88319-1-ljp@linux.ibm.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfJakub Kicinski authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net 1) Honor stateful expressions defined in the set from the dynset extension. The set definition provides a stateful expression that must be used by the dynset expression in case it is specified. 2) Missing timeout extension in the set element in the dynset extension leads to inconsistent ruleset listing, not allowing the user to restore timeout and expiration on ruleset reload. 3) Do not dump the stateful expression from the dynset extension if it coming from the set definition. * git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf: netfilter: nft_dynset: dump expressions when set definition contains no expressions netfilter: nft_dynset: add timeout extension to template netfilter: nft_dynset: honor stateful expressions in set definition ==================== Link: https://lore.kernel.org/r/20210127132512.5472-1-pablo@netfilter.orgSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'linux-can-fixes-for-5.11-20210127' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2021-01-27 The patch is by Dan Carpenter and fixes a potential information leak in can_fill_info(). * tag 'linux-can-fixes-for-5.11-20210127' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: can: dev: prevent potential information leak in can_fill_info() ==================== Link: https://lore.kernel.org/r/20210127094028.2778793-1-mkl@pengutronix.deSigned-off-by:
-
Jakub Kicinski authored
include/net/bonding.h is missing from bonding entry. Link: https://lore.kernel.org/r/20210127021844.4071706-1-kuba@kernel.orgSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueJakub Kicinski authored
Anthony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-01-26 This series contains updates to the ice, i40e, and igc driver. Henry corrects setting an unspecified protocol to IPPROTO_NONE instead of 0 for IPv6 flexbytes filters for ice. Nick fixes the IPv6 extension header being processed incorrectly and updates the netdev->dev_addr if it exists in hardware as it may have been modified outside the ice driver. Brett ensures a user cannot request more channels than available LAN MSI-X and fixes the minimum allocation logic as it was incorrectly trying to use more MSI-X than allocated for ice. Stefan Assmann minimizes the delay between getting and using the VSI pointer to prevent a possible crash for i40e. Corinna Vinschen fixes link speed advertising for igc. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: igc: fix link speed advertising i40e: acquire VSI pointer only after VF is initialized ice: Fix MSI-X vector fallback logic ice: Don't allow more channels than LAN MSI-X available ice: update dev_addr in ice_set_mac_address even if HW filter exists ice: Implement flow for IPv6 next header (extension header) ice: fix FDir IPv6 flexbyte ==================== Link: https://lore.kernel.org/r/20210126221035.658124-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Vadim Fedorenko authored
On building the route there is an assumption that the destination could be local. In this case loopback_dev is used to get the address. If the address is still cannot be retrieved dn_route_output_slow returns EADDRNOTAVAIL with loopback_dev reference taken. Cannot find hash for the fixes tag because this code was introduced long time ago. I don't think that this bug has ever fired but the patch is done just to have a consistent code base. Signed-off-by:
Vadim Fedorenko <vfedorenko@novek.ru> Link: https://lore.kernel.org/r/1611619334-20955-1-git-send-email-vfedorenko@novek.ruSigned-off-by:
-
Rasmus Villemoes authored
It's not true that switchdev_port_obj_notify() only inspects the ->handled field of "struct switchdev_notifier_port_obj_info" if call_switchdev_blocking_notifiers() returns 0 - there's a WARN_ON() triggering for a non-zero return combined with ->handled not being true. But the real problem here is that -EOPNOTSUPP is not being properly handled. The wrapper functions switchdev_handle_port_obj_add() et al change a return value of -EOPNOTSUPP to 0, and the treatment of ->handled in switchdev_port_obj_notify() seems to be designed to change that back to -EOPNOTSUPP in case nobody actually acted on the notifier (i.e., everybody returned -EOPNOTSUPP). Currently, as soon as some device down the stack passes the check_cb() check, ->handled gets set to true, which means that switchdev_port_obj_notify() cannot actually ever return -EOPNOTSUPP. This, for example, means that the detection of hardware offload support in the MRP code is broken: switchdev_port_obj_add() used by br_mrp_switchdev_send_ring_test() always returns 0, so since the MRP code thinks the generation of MRP test frames has been offloaded, no such frames are actually put on the wire. Similarly, br_mrp_switchdev_set_ring_role() also always returns 0, causing mrp->ring_role_offloaded to be set to 1. To fix this, continue to set ->handled true if any callback returns success or any error distinct from -EOPNOTSUPP. But if all the callbacks return -EOPNOTSUPP, make sure that ->handled stays false, so the logic in switchdev_port_obj_notify() can propagate that information. Fixes: 9a9f26e8 ("bridge: mrp: Connect MRP API with the switchdev API") Fixes: f30f0601 ("switchdev: Add helpers to aid traversal through lower devices") Reviewed-by:
Rasmus Villemoes <rasmus.villemoes@prevas.dk> Link: https://lore.kernel.org/r/20210125124116.102928-1-rasmus.villemoes@prevas.dkSigned-off-by:
-
- 27 Jan, 2021 6 commits
-
-
Dan Carpenter authored
The "bec" struct isn't necessarily always initialized. For example, the mcp251xfd_get_berr_counter() function doesn't initialize anything if the interface is down. Fixes: 52c793f2 ("can: netlink support for bus-error reporting and counters") Link: https://lore.kernel.org/r/YAkaRdRJncsJO8Ve@mwandaSigned-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Jakub Kicinski authored
Laurent Badel says: ==================== net: fec: Fix temporary RMII clock reset on link up v2: fixed a compilation warning The FEC drivers performs a "hardware reset" of the MAC module when the link is reported to be up. This causes a short glitch in the RMII clock due to the hardware reset clearing the receive control register which controls the MII mode. It seems that some link partners do not tolerate this glitch, and invalidate the link, which leads to a never-ending loop of negotiation-link up-link down events. This was observed with the iMX28 Soc and LAN8720/LAN8742 PHYs, with two Intel adapters I218-LM and X722-DA2 as link partners, though a number of other link partners do not seem to mind the clock glitch. Changing the hardware reset to a software reset (clearing bit 1 of the ECR register) cured the issue. Attempts to optimize fec_restart() in order to minimize the duration of the glitch were unsuccessful. Furthermore manually producing the glitch by setting MII mode and then back to RMII in two consecutive instructions, resulting in a clock glitch <10us in duration, was enough to cause the partner to invalidate the link. This strongly suggests that the root cause of the link being dropped is indeed the change in clock frequency. In an effort to minimize changes to driver, the patch proposes to use soft reset only for tested SoCs (iMX28) and only if the link is up. This preserves hardware reset in other situations, which might be required for proper setup of the MAC. ==================== Link: https://lore.kernel.org/r/20210125100745.5090-1-laurentbadel@eaton.comSigned-off-by:
-
Laurent Badel authored
fec_restart() does a hard reset of the MAC module when the link status changes to up. This temporarily resets the R_CNTRL register which controls the MII mode of the ENET_OUT clock. In the case of RMII, the clock frequency momentarily drops from 50MHz to 25MHz until the register is reconfigured. Some link partners do not tolerate this glitch and invalidate the link causing failure to establish a stable link when using PHY polling mode. Since as per IEEE802.3 the criteria for link validity are PHY-specific, what the partner should tolerate cannot be assumed, so avoid resetting the MII clock by using software reset instead of hardware reset when the link is up. This is generally relevant only if the SoC provides the clock to an external PHY and the PHY is configured for RMII. Signed-off-by:
Laurent Badel <laurentbadel@eaton.com> Signed-off-by:
-
Xie He authored
In the lapb module, the timers may run concurrently with other code in this module, and there is currently no locking to prevent the code from racing on "struct lapb_cb". This patch adds locking to prevent racing. 1. Add "spinlock_t lock" to "struct lapb_cb"; Add "spin_lock_bh" and "spin_unlock_bh" to APIs, timer functions and notifier functions. 2. Add "bool t1timer_stop, t2timer_stop" to "struct lapb_cb" to make us able to ask running timers to abort; Modify "lapb_stop_t1timer" and "lapb_stop_t2timer" to make them able to abort running timers; Modify "lapb_t2timer_expiry" and "lapb_t1timer_expiry" to make them abort after they are stopped by "lapb_stop_t1timer", "lapb_stop_t2timer", and "lapb_start_t1timer", "lapb_start_t2timer". 3. Let lapb_unregister wait for other API functions and running timers to stop. 4. The lapb_device_event function calls lapb_disconnect_request. In order to avoid trying to hold the lock twice, add a new function named "__lapb_disconnect_request" which assumes the lock is held, and make it called by lapb_disconnect_request and lapb_device_event. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by:
Xie He <xie.he.0141@gmail.com> Link: https://lore.kernel.org/r/20210126040939.69995-1-xie.he.0141@gmail.comSigned-off-by:
-
Ivan Vecera authored
Function __team_compute_features() is protected by team->lock mutex when it is called from team_compute_features() used when features of an underlying device is changed. This causes a deadlock when NETDEV_FEAT_CHANGE notifier for underlying device is fired due to change propagated from team driver (e.g. MTU change). It's because callbacks like team_change_mtu() or team_vlan_rx_{add,del}_vid() protect their port list traversal by team->lock mutex. Example (r8169 case where this driver disables TSO for certain MTU values): ... [ 6391.348202] __mutex_lock.isra.6+0x2d0/0x4a0 [ 6391.358602] team_device_event+0x9d/0x160 [team] [ 6391.363756] notifier_call_chain+0x47/0x70 [ 6391.368329] netdev_update_features+0x56/0x60 [ 6391.373207] rtl8169_change_mtu+0x14/0x50 [r8169] [ 6391.378457] dev_set_mtu_ext+0xe1/0x1d0 [ 6391.387022] dev_set_mtu+0x52/0x90 [ 6391.390820] team_change_mtu+0x64/0xf0 [team] [ 6391.395683] dev_set_mtu_ext+0xe1/0x1d0 [ 6391.399963] do_setlink+0x231/0xf50 ... In fact team_compute_features() called from team_device_event() does not need to be protected by team->lock mutex and rcu_read_lock() is sufficient there for port list traversal. Fixes: 3d249d4c ("net: introduce ethernet teaming device") Cc: Saeed Mahameed <saeed@kernel.org> Signed-off-by:Ivan Vecera <ivecera@redhat.com> Reviewed-by:
Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/20210125074416.4056484-1-ivecera@redhat.comSigned-off-by:
-
Jakub Kicinski authored
David has been the de-facto maintainer for much of the IP code for the last couple of years, let's make it official. Link: https://lore.kernel.org/r/20210122173220.3579491-1-kuba@kernel.orgSigned-off-by:
-
- 26 Jan, 2021 21 commits
-
-
Paul Blakey authored
If a non nat tuple entry is inserted just to the regular tuples rhashtable (ct_tuples_ht) and not to natted tuples rhashtable (ct_nat_tuples_ht). Commit bc562be9 ("net/mlx5e: CT: Save ct entries tuples in hashtables") mixed up the return labels and names sot that on cleanup or failure we still try to remove for the natted tuples rhashtable. Fix that by correctly checking if a natted tuples insertion before removing it. While here make it more readable. Fixes: bc562be9 ("net/mlx5e: CT: Save ct entries tuples in hashtables") Reviewed-by:
Roi Dayan <roid@nvidia.com> Signed-off-by:
Paul Blakey <paulb@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
Sometimes, channel params are changed without recreating the channels. It happens in two basic cases: when the channels are closed, and when the parameter being changed doesn't affect how channels are configured. Such changes invoke a hardware command that might fail. The whole operation should be reverted in such cases, but the code that restores the parameters' values in the driver was missing. This commit adds this handling. Fixes: 2e20a151 ("net/mlx5e: Fail safe mtu and lro setting") Signed-off-by:
Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
-
Maxim Mikityanskiy authored
Trust state may be changed without recreating the channels. It happens when the channels are closed, and when channel parameters (min inline mode) stay the same after changing the trust state. Changing the trust state is a hardware command that may fail. The current code didn't restore the channel parameters to their old values if an error happened and the channels were closed. This commit adds handling for this case. Fixes: 6e0504c6 ("net/mlx5e: Change inline mode correctly when changing trust state") Signed-off-by:
-
Maxim Mikityanskiy authored
This commit addresses two issues related to changing the number of queues when the channels are closed: 1. Missing call to mlx5e_num_channels_changed to update real_num_tx_queues when the number of TCs is changed. 2. When mlx5e_num_channels_changed returns an error, the channel parameters must be reverted. Two Fixes: tags correspond to the first commits where these two issues were introduced. Fixes: 3909a12e ("net/mlx5e: Fix configuration of XPS cpumasks and netdev queues in corner cases") Fixes: fa374877 ("net/mlx5e: Handle errors from netif_set_real_num_{tx,rx}_queues") Signed-off-by:
-
Paul Blakey authored
Currently, if a neighbour isn't valid when offloading tunnel encap rules, we offload the original match and replace the original action with "goto slow path" action. For this we use a temporary flow attribute based on the original flow attribute and then change the action. Flow flags, which among those is the CT flag, are still shared for the slow path rule offload, so we end up parsing this flow as a CT + goto slow path rule. Besides being unnecessary, CT action offload saves extra information in the passed flow attribute, such as created ct_flow and mod_hdr, which is lost onces the temporary flow attribute is freed. When a neigh is updated and is valid, we offload the original CT rule with original CT action, which again creates a ct_flow and mod_hdr and saves it in the flow's original attribute. Then we delete the slow path rule with a temporary flow attribute based on original updated flow attribute, and we free the relevant ct_flow and mod_hdr. Then when tc deletes this flow, we try to free the ct_flow and mod_hdr on the flow's attribute again. To fix the issue, skip all furture proccesing (CT/Sample/Split rules) in offload/unoffload of slow path rules. Call trace: [ 758.850525] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000218 [ 758.952987] Internal error: Oops: 96000005 [#1] PREEMPT SMP [ 758.964170] Modules linked in: act_csum(E) act_pedit(E) act_tunnel_key(E) act_ct(E) nf_flow_table(E) xt_nat(E) ip6table_filter(E) ip6table_nat(E) xt_comment(E) ip6_tables(E) xt_conntrack(E) xt_MASQUERADE(E) nf_conntrack_netlink(E) xt_addrtype(E) iptable_filter(E) iptable_nat(E) bpfilter(E) br_netfilter(E) bridge(E) stp(E) llc(E) xfrm_user(E) overlay(E) act_mirred(E) act_skbedit(E) rdma_ucm(OE) rdma_cm(OE) iw_cm(OE) ib_ipoib(OE) ib_cm(OE) ib_umad(OE) esp6_offload(E) esp6(E) esp4_offload(E) esp4(E) xfrm_algo(E) mlx5_ib(OE) ib_uverbs(OE) geneve(E) ip6_udp_tunnel(E) udp_tunnel(E) nfnetlink_cttimeout(E) nfnetlink(E) mlx5_core(OE) act_gact(E) cls_flower(E) sch_ingress(E) openvswitch(E) nsh(E) nf_conncount(E) nf_nat(E) mlxfw(OE) psample(E) nf_conntrack(E) nf_defrag_ipv4(E) vfio_mdev(E) mdev(E) ib_core(OE) mlx_compat(OE) crct10dif_ce(E) uio_pdrv_genirq(E) uio(E) i2c_mlx(E) mlxbf_pmc(E) sbsa_gwdt(E) mlxbf_gige(E) gpio_mlxbf2(E) mlxbf_pka(E) mlx_trio(E) mlx_bootctl(E) bluefield_edac(E) knem(O) [ 758.964225] ip_tables(E) mlxbf_tmfifo(E) ipv6(E) crc_ccitt(E) nf_defrag_ipv6(E) [ 759.154186] CPU: 5 PID: 122 Comm: kworker/u16:1 Tainted: G OE 5.4.60-mlnx.52.gde81e85 #1 [ 759.172870] Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS BlueField:3.5.0-2-gc1b5d64 Jan 4 2021 [ 759.195466] Workqueue: mlx5e mlx5e_rep_neigh_update [mlx5_core] [ 759.207344] pstate: a0000005 (NzCv daif -PAN -UAO) [ 759.217003] pc : mlx5_del_flow_rules+0x5c/0x160 [mlx5_core] [ 759.228229] lr : mlx5_del_flow_rules+0x34/0x160 [mlx5_core] [ 759.405858] Call trace: [ 759.410804] mlx5_del_flow_rules+0x5c/0x160 [mlx5_core] [ 759.421337] __mlx5_eswitch_del_rule.isra.43+0x5c/0x1c8 [mlx5_core] [ 759.433963] mlx5_eswitch_del_offloaded_rule_ct+0x34/0x40 [mlx5_core] [ 759.446942] mlx5_tc_rule_delete_ct+0x68/0x74 [mlx5_core] [ 759.457821] mlx5_tc_ct_delete_flow+0x160/0x21c [mlx5_core] [ 759.469051] mlx5e_tc_unoffload_fdb_rules+0x158/0x168 [mlx5_core] [ 759.481325] mlx5e_tc_encap_flows_del+0x140/0x26c [mlx5_core] [ 759.492901] mlx5e_rep_update_flows+0x11c/0x1ec [mlx5_core] [ 759.504127] mlx5e_rep_neigh_update+0x160/0x200 [mlx5_core] [ 759.515314] process_one_work+0x178/0x400 [ 759.523350] worker_thread+0x58/0x3e8 [ 759.530685] kthread+0x100/0x12c [ 759.537152] ret_from_fork+0x10/0x18 [ 759.544320] Code: 97ffef55 51000673 3100067f 54ffff41 (b9421ab3) [ 759.556548] ---[ end trace fab818bb1085832d ]--- Fixes: 4c3844d9 ("net/mlx5e: CT: Introduce connection tracking") Signed-off-by:
Vlad Buslov <vladbu@nvidia.com> Signed-off-by:
-
Maor Dickman authored
The cited commit introduce new CONFIG_MLX5_CLS_ACT kconfig variable to control compilation of TC hardware offloads implementation. When this configuration is disabled the driver is still wrongly reports in ethtool that hw-tc-offload is supported. Fixed by reporting hw-tc-offload is supported only when CONFIG_MLX5_CLS_ACT is enabled. Fixes: d956873f ("net/mlx5e: Introduce kconfig var for TC support") Signed-off-by:
Maor Dickman <maord@nvidia.com> Reviewed-by:
-
Daniel Jurgens authored
Pages for the host PF and ECPF were stored in the same tree, so the ECPF pages were being freed along with the host PF's when the host driver unloaded. Combine the function ID and ECPF flag to use as an index into the x-array containing the trees to get a different tree for the host PF and ECPF. Fixes: c6168161 ("net/mlx5: Add support for release all pages event") Signed-off-by:
Daniel Jurgens <danielj@nvidia.com> Signed-off-by:
-
Maxim Mikityanskiy authored
When IPSEC offload isn't active, the number of stats is not zero, but the strings are not filled, leading to exposing stats with empty names. Fix this by using the same condition for NUM_STATS and FILL_STRS. Fixes: 0aab3e1b ("net/mlx5e: IPSec, Expose IPsec HW stat only for supporting HW") Signed-off-by:
Raed Salem <raeds@nvidia.com> Reviewed-by:
-
Maor Dickman authored
"Unsupported key used:" appears in kernel log when flows with unsupported key are used, arp fields for example. OpenVSwitch was changed to match on arp fields by default that caused this warning to appear in kernel log for every arp rule, which can be a lot. Fix by lowering print level from warning to debug. Fixes: e3a2b7ed ("net/mlx5e: Support offload cls_flower with drop action") Signed-off-by:
-
Pan Bian authored
Instead of directly return, goto the error handling label to free allocated page. Fixes: 5f29458b ("net/mlx5e: Support dump callback in TX reporter") Signed-off-by:
Pan Bian <bianpan2016@163.com> Reviewed-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
-
Parav Pandit authored
rate_bytes_ps is a 64-bit field. It passed as 32-bit field to apply_police_params(). Due to this when police rate is higher than 4Gbps, 32-bit calculation ignores the carry. This results in incorrect rate configurationn the device. Fix it by performing 64-bit calculation. Fixes: fcb64c0f ("net/mlx5: E-Switch, add ingress rate support") Signed-off-by:
Parav Pandit <parav@nvidia.com> Reviewed-by:
Eli Cohen <elic@nvidia.com> Signed-off-by:
-
Roi Dayan authored
When we create the ft object we also init rhltable in ft->fgs_hash. So in error flow before kfree of ft we need to destroy that rhltable. Fixes: 693c6883 ("net/mlx5: Add hash table for flow groups in flow table") Signed-off-by:
-
Jakub Kicinski authored
Merge tag 'mac80211-for-net-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== A couple of fixes: * fix 160 MHz channel switch in mac80211 * fix a staging driver to not deadlock due to some recent cfg80211 changes * fix NULL-ptr deref if cfg80211 returns -EINPROGRESS to wext (syzbot) * pause TX in mac80211 in type change to prevent crashes (syzbot) * tag 'mac80211-for-net-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211: staging: rtl8723bs: fix wireless regulatory API misuse mac80211: pause TX while changing interface type wext: fix NULL-ptr-dereference with cfg80211's lack of commit() mac80211: 160MHz with extended NSS BW in CSA ==================== Link: https://lore.kernel.org/r/20210126130529.75225-1-johannes@sipsolutions.netSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'wireless-drivers-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.11 Second set of fixes for v5.11. Like in last time we again have more fixes than usual Actually a bit too much for my liking in this state of the cycle, but due to unrelated challenges I was only able to submit them now. We have few important crash fixes, iwlwifi modifying read-only data being the most reported issue, and also smaller fixes to iwlwifi. mt76 * fix a clang warning about enum usage * fix rx buffer refcounting crash mt7601u * fix rx buffer refcounting crash * fix crash when unbplugging the device iwlwifi * fix a crash where we were modifying read-only firmware data * lots of smaller fixes all over the driver * tag 'wireless-drivers-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers: (24 commits) mt7601u: fix kernel crash unplugging the device iwlwifi: queue: bail out on invalid freeing iwlwifi: mvm: guard against device removal in reprobe iwlwifi: Fix IWL_SUBDEVICE_NO_160 macro to use the correct bit. iwlwifi: mvm: clear IN_D3 after wowlan status cmd iwlwifi: pcie: add rules to match Qu with Hr2 iwlwifi: mvm: invalidate IDs of internal stations at mvm start iwlwifi: mvm: fix the return type for DSM functions 1 and 2 iwlwifi: pcie: reschedule in long-running memory reads iwlwifi: pcie: use jiffies for memory read spin time limit iwlwifi: pcie: fix context info memory leak iwlwifi: pcie: add a NULL check in iwl_pcie_txq_unmap iwlwifi: pcie: set LTR on more devices iwlwifi: queue: don't crash if txq->entries is NULL iwlwifi: fix the NMI flow for old devices iwlwifi: pnvm: don't try to load after failures iwlwifi: pnvm: don't skip everything when not reloading iwlwifi: pcie: avoid potential PNVM leaks iwlwifi: mvm: take mutex for calling iwl_mvm_get_sync_time() iwlwifi: mvm: skip power command when unbinding vif during CSA ... ==================== Link: https://lore.kernel.org/r/20210126092202.6A367C433CA@smtp.codeaurora.orgSigned-off-by:
-
Eric Dumazet authored
net/core/tso.c got recent support for USO, and this broke iwlfifi because the driver implemented a limited form of GSO. Providing ->gso_type allows for skb_is_gso_tcp() to provide a correct result. Fixes: 3d5b459b ("net: tso: add UDP segmentation support") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Ben Greear <greearb@candelatech.com> Tested-by:
-
Corinna Vinschen authored
Link speed advertising in igc has two problems: - When setting the advertisement via ethtool, the link speed is converted to the legacy 32 bit representation for the intel PHY code. This inadvertently drops ETHTOOL_LINK_MODE_2500baseT_Full_BIT (being beyond bit 31). As a result, any call to `ethtool -s ...' drops the 2500Mbit/s link speed from the PHY settings. Only reloading the driver alleviates that problem. Fix this by converting the ETHTOOL_LINK_MODE_2500baseT_Full_BIT to the Intel PHY ADVERTISE_2500_FULL bit explicitly. - Rather than checking the actual PHY setting, the .get_link_ksettings function always fills link_modes.advertising with all link speeds the device is capable of. Fix this by checking the PHY autoneg_advertised settings and report only the actually advertised speeds up to ethtool. Fixes: 8c5ad0da ("igc: Add ethtool support") Signed-off-by:
Corinna Vinschen <vinschen@redhat.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Stefan Assmann authored
This change simplifies the VF initialization check and also minimizes the delay between acquiring the VSI pointer and using it. As known by the commit being fixed, there is a risk of the VSI pointer getting changed. Therefore minimize the delay between getting and using the pointer. Fixes: 9889707b ("i40e: Fix crash caused by stress setting of VF MAC addresses") Signed-off-by:
Stefan Assmann <sassmann@kpanic.de> Reviewed-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by:
-
Brett Creeley authored
The current MSI-X enablement logic tries to enable best-case MSI-X vectors and if that fails we only support a bare-minimum set. This includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X for the OICR interrupt. Unfortunately, the driver fails to load when we don't get as many MSI-X as requested for a couple reasons. First, the code to allocate MSI-X in the driver tries to allocate num_online_cpus() MSI-X for LAN traffic without caring about the number of MSI-X actually enabled/requested from the kernel for LAN traffic. So, when calling ice_get_res() for the PF VSI, it returns failure because the number of available vectors is less than requested. Fix this by not allowing the PF VSI to allocation more than pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues. Limiting the number of queues is done because we don't want more than 1 Tx/Rx queue per interrupt due to performance conerns. Second, the driver assigns pf->num_lan_msix = 2, to account for LAN traffic and the OICR. However, pf->num_lan_msix is only meant for LAN MSI-X. This is causing a failure when the PF VSI tries to allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has already been reserved, so there may not be enough MSI-X vectors left. Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for the failure case. Update the related defines used in ice_ena_msix_range() to align with the above behavior and remove the unused RDMA defines because RDMA is currently not supported. Also, remove the now incorrect comment. Fixes: 152b978a ("ice: Rework ice_ena_msix_range") Signed-off-by:
Brett Creeley <brett.creeley@intel.com> Tested-by:
Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by:
-
Brett Creeley authored
Currently users could create more channels than LAN MSI-X available. This is happening because there is no check against pf->num_lan_msix when checking the max allowed channels and will cause performance issues if multiple Tx and Rx queues are tied to a single MSI-X. Fix this by not allowing more channels than LAN MSI-X available in pf->num_lan_msix. Fixes: 87324e74 ("ice: Implement ethtool ops for channels") Signed-off-by:
-
Nick Nunley authored
Fix the driver to copy the MAC address configured in ndo_set_mac_address into dev_addr, even if the MAC filter already exists in HW. In some situations (e.g. bonding) the netdev's dev_addr could have been modified outside of the driver, with no change to the HW filter, so the driver cannot assume that they match. Fixes: 757976ab ("ice: Fix check for removing/adding mac filters") Signed-off-by:
Nick Nunley <nicholas.d.nunley@intel.com> Tested-by:
-
Nick Nunley authored
This patch is based on a similar change to i40e by Slawomir Laba: "i40e: Implement flow for IPv6 next header (extension header)". When a packet contains an IPv6 header with next header which is an extension header and not a protocol one, the kernel function skb_transport_header called with such sk_buff will return a pointer to the extension header and not to the TCP one. The above explained call caused a problem with packet processing for skb with encapsulation for tunnel with ICE_TX_CTX_EIPT_IPV6. The extension header was not skipped at all. The ipv6_skip_exthdr function does check if next header of the IPV6 header is an extension header and doesn't modify the l4_proto pointer if it points to a protocol header value so its safe to omit the comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can return value -1. This means that the skipping process failed and there is something wrong with the packet so it will be dropped. Fixes: a4e82a81 ("ice: Add support for tunnel offloads") Signed-off-by:
-
