Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-04-01

This series contains updates to i40e driver only.

Arkadiusz fixes warnings for inconsistent indentation.

Magnus fixes an issue on xsk receive where single packets over time
are batched rather than received immediately.

Eryk corrects warnings and reporting of veb-stats.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
mptcp: mptcp: fix deadlock in mptcp{,6}_release

syzkaller has reported a few deadlock triggered by
mptcp{,6}_release.

These patches address the issue in the easy way - blocking
the relevant, multicast related, sockopt options on MPTCP
sockets.

Note that later on net-next we are going to revert patch 1/2,
as a part of a larger MPTCP sockopt implementation refactor
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This change reverts commit ad98dd37 ("mptcp: provide subflow aware
release function"). The latter introduced a deadlock spotted by
syzkaller and is not needed anymore after the previous commit.

Fixes: ad98dd37 ("mptcp: provide subflow aware release function")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unrolling mcast state at msk dismantel time is bug prone, as
syzkaller reported:

======================================================
WARNING: possible circular locking dependency detected
5.11.0-syzkaller #0 Not tainted
------------------------------------------------------
syz-executor905/8822 is trying to acquire lock:
ffffffff8d678fe8 (rtnl_mutex){+.+.}-{3:3}, at: ipv6_sock_mc_close+0xd7/0x110 net/ipv6/mcast.c:323

but task is already holding lock:
ffff888024390120 (sk_lock-AF_INET6){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1600 [inline]
ffff888024390120 (sk_lock-AF_INET6){+.+.}-{0:0}, at: mptcp6_release+0x57/0x130 net/mptcp/protocol.c:3507

which lock already depends on the new lock.

Instead we can simply forbit any mcast-related setsockopt

Fixes: 717e79c8 ("mptcp: Add setsockopt()/getsockopt() socket operations")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported memory leak in peak_usb.
The problem was in case of failure after calling
->dev_init()[2] in peak_usb_create_dev()[1]. The data
allocated int dev_init() wasn't freed, so simple
->dev_free() call fix this problem.

backtrace:
    [<0000000079d6542a>] kmalloc include/linux/slab.h:552 [inline]
    [<0000000079d6542a>] kzalloc include/linux/slab.h:682 [inline]
    [<0000000079d6542a>] pcan_usb_fd_init+0x156/0x210 drivers/net/can/usb/peak_usb/pcan_usb_fd.c:868   [2]
    [<00000000c09f9057>] peak_usb_create_dev drivers/net/can/usb/peak_usb/pcan_usb_core.c:851 [inline] [1]
    [<00000000c09f9057>] peak_usb_probe+0x389/0x490 drivers/net/can/usb/peak_usb/pcan_usb_core.c:949

Reported-by: syzbot+91adee8d9ebb9193d22d@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support for UDP_GRO was added in the past but the implementation for
getsockopt was missed which did lead to an error when we tried to
retrieve the setting for UDP_GRO. This patch adds the missing switch
case for UDP_GRO

Fixes: e20cf8d3 ("udp: implement GRO for plain UDP sockets.")
Signed-off-by: Norman Maurer <norman_maurer@apple.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported memory leak in atusb_probe()[1].
The problem was in atusb_alloc_urbs().
Since urb is anchored, we need to release the reference
to correctly free the urb

backtrace:
    [<ffffffff82ba0466>] kmalloc include/linux/slab.h:559 [inline]
    [<ffffffff82ba0466>] usb_alloc_urb+0x66/0xe0 drivers/usb/core/urb.c:74
    [<ffffffff82ad3888>] atusb_alloc_urbs drivers/net/ieee802154/atusb.c:362 [inline][2]
    [<ffffffff82ad3888>] atusb_probe+0x158/0x820 drivers/net/ieee802154/atusb.c:1038 [1]

Reported-by: syzbot+28a246747e0a465127f3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If veb-stats was enabled, the ethtool stats triggered a warning
due to invalid size: 'unexpected stat size for veb.tc_%u_tx_packets'.
This was due to an incorrect structure definition for the statistics.
Structures and functions have been improved in line with requirements
for the presentation of statistics, in particular for the functions:
'i40e_add_ethtool_stats' and 'i40e_add_stat_strings'.

Fixes: 1510ae0b ("i40e: convert VEB TC stats to use an i40e_stats array")
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Fix so that single packets are received immediately instead of in
batches of 8. If you sent 1 pps to a system, you received 8 packets
every 8 seconds instead of 1 packet every second. The problem behind
this was that the work_done reporting from the Tx part of the driver
was broken. The work_done reporting in i40e controls not only the
reporting back to the napi logic but also the setting of the interrupt
throttling logic. When Tx or Rx reports that it has more to do,
interrupts are throttled or coalesced and when they both report that
they are done, interrupts are armed right away. If the wrong work_done
value is returned, the logic will start to throttle interrupts in a
situation where it should have just enabled them. This leads to the
undesired batching behavior seen in user-space.

Fix this by returning the correct boolean value from the Tx xsk
zero-copy path. Return true if there is nothing to do or if we got
fewer packets to process than we asked for. Return false if we got as
many packets as the budget since there might be more packets we can
process.

Fixes: 3106c580 ("i40e: Use batched xsk Tx interfaces to increase performance")
Reported-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Fixed new static analysis findings:
"warn: inconsistent indenting" - introduced lately,
reported with lkp and smatch build.

Fixes: 4b208eaa ("i40e: Add init and default config of software based DCB")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

xdp_return_frame() may be called outside of NAPI context to return
xdpf back to page_pool. xdp_return_frame() calls __xdp_return() with
napi_direct = false. For page_pool memory model, __xdp_return() calls
xdp_return_frame_no_direct() unconditionally and below false negative
kernel BUG throw happened under preempt-rt build:

[  430.450355] BUG: using smp_processor_id() in preemptible [00000000] code: modprobe/3884
[  430.451678] caller is __xdp_return+0x1ff/0x2e0
[  430.452111] CPU: 0 PID: 3884 Comm: modprobe Tainted: G     U      E     5.12.0-rc2+ #45

Changes in v2:
 - This patch fixes the issue by making xdp_return_frame_no_direct() is
   only called if napi_direct = true, as recommended for better by
   Jesper Dangaard Brouer. Thanks!

Fixes: 2539650f ("xdp: Helpers for disabling napi_direct of xdp_return_frame")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit f211ac15.

We had similar attempt in the past, and we reverted it.

History:

64a14651 [NET]: Revert incorrect accept queue backlog changes.
8488df89 [NET]: Fix bugs in "Whether sock accept queue is full" checking

I am adding a fat comment so that future attempts will
be much harder.

Fixes: f211ac15 ("net: correct sk_acceptq_is_full()")
Cc: iuyacan <yacanliu@163.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 fixes 2021-03-31

This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2021-03-31

1) Fix ipv4 pmtu checks for xfrm anf vti interfaces.
   From Eyal Birger.

2) There are situations where the socket passed to
   xfrm_output_resume() is not the same as the one
   attached to the skb. Use the socket passed to
   xfrm_output_resume() to avoid lookup failures
   when xfrm is used with VRFs.
   From Evan Nimmo.

3) Make the xfrm_state_hash_generation sequence counter per
   network namespace because but its write serialization
   lock is also per network namespace. Write protection
   is insufficient otherwise.
   From Ahmed S. Darwish.

4) Fixup sctp featue flags when used with esp offload.
   From Xin Long.

5) xfrm BEET mode doesn't support fragments for inner packets.
   This is a limitation of the protocol, so no fix possible.
   Warn at least to notify the user about that situation.
   From Xin Long.

6) Fix NULL pointer dereference on policy lookup when
   namespaces are uses in combination with esp offload.

7) Fix incorrect transformation on esp offload when
   packets get segmented at layer 3.

8) Fix some user triggered usages of WARN_ONCE in
   the xfrm compat layer.
   From Dmitry Safonov.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In rds_message_map_pages, the rm is freed by rds_message_put(rm).
But rm is still used by rm->data.op_sg in return value.

My patch assigns ERR_CAST(rm->data.op_sg) to err before the rm is
freed to avoid the uaf.

Fixes: 7dba9203 ("net/rds: Use ERR_PTR for rds_message_alloc_sgs()")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After a short network outage, the dst_entry is timed out and put
in DST_OBSOLETE_DEAD. We are in this code because arp reply comes
from this neighbour after network recovers. There is a potential
race condition that dst_entry is still in DST_OBSOLETE_DEAD.
With that, another neighbour lookup causes more harm than good.

In best case all packets in arp_queue are lost. This is
counterproductive to the original goal of finding a better path
for those packets.

I observed a worst case with 4.x kernel where a dst_entry in
DST_OBSOLETE_DEAD state is associated with loopback net_device.
It leads to an ethernet header with all zero addresses.
A packet with all zero source MAC address is quite deadly with
mac80211, ath9k and 802.11 block ack.  It fails
ieee80211_find_sta_by_ifaddr in ath9k (xmit.c). Ath9k flushes tx
queue (ath_tx_complete_aggr). BAW (block ack window) is not
updated. BAW logic is damaged and ath9k transmission is disabled.
Signed-off-by: Tong Zhu <zhutong@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

XSK wakeup flow triggers an IRQ by posting a NOP WQE and hitting
the doorbell on the async ICOSQ.
It maintains its state so that it doesn't issue another NOP WQE
if it has an outstanding one already.

For this flow to work properly, the NOP post must not fail.
Make sure to reserve room for the NOP WQE in all WQE posts to the
async ICOSQ.

Fixes: 8d94b590 ("net/mlx5e: Turn XSK ICOSQ into a general asynchronous one")
Fixes: 1182f365 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Fixes: 0419d8c9 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Current algorithm for encap keys is legacy from initial vxlan
implementation and doesn't take into account all possible fields of a
tunnel. For example, for a Geneve tunnel, which may have additional TLV
options, they are ignored when comparing encap keys and a rule can be
attached to an incorrect encap entry.

Fix that by introducing encap_info_equal() operation in
struct mlx5e_tc_tunnel. Geneve tunnel type uses custom implementation,
which extends generic algorithm and considers options if they are set.

Fixes: 7f1a546e ("net/mlx5e: Consider tunnel type for encap contexts")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Calculating the number of compeltion EQs based on the number of
available IRQ vectors doesn't work now that all async EQs share one IRQ.
Thus the max number of EQs can be exceeded on systems with more than
approximately 256 CPUs. Take this into account when calculating the
number of available completion EQs.

Fixes: 81bfa206 ("net/mlx5: Use a single IRQ for all async EQs")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Some TLS RX counters increment per socket/connection, and are not
protected against parallel modifications from several cores.
Switch them to atomic counters by taking them out of the RQ stats into
the global atomic TLS stats.

In this patch, we touch 'rx_tls_ctx/del' that count the number of
device-offloaded RX TLS connections added/deleted.
These counters are updated in the add/del callbacks, out of the fast
data-path.

This change is not needed for counters that increment only in NAPI
context, as they are protected by the NAPI mechanism.
Keep them as tls_* counters under 'struct mlx5e_rq_stats'.

Fixes: 76c1e1ac ("net/mlx5e: kTLS, Add kTLS RX stats")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Some TLS TX counters increment per socket/connection, and are not
protected against parallel modifications from several cores.
Switch them to atomic counters by taking them out of the SQ stats into
the global atomic TLS stats.

In this patch, we touch a single counter 'tx_tls_ctx' that counts the
number of device-offloaded TX TLS connections added.
Now that this counter can be increased without the for having the SQ
context in hand, move it to the mlx5e_ktls_add_tx() callback where it
really belongs, out of the fast data-path.

This change is not needed for counters that increment only in NAPI
context or under the TX lock, as they are already protected.
Keep them as tls_* counters under 'struct mlx5e_sq_stats'.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Create send to vport miss group was added in order to support traffic
recirculation to root table with metadata source rewrite.
This group is created also in case source rewrite isn't supported.

Fixed by creating send to vport miss group only if source rewrite is
supported by FW.

Fixes: 8e404fef ("net/mlx5e: Match recirculated packet miss in slow table using reg_c1")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Use connector_type read from PTYS register when it's valid, based on
corresponding capability bit.

Fixes: 5b4793f8 ("net/mlx5e: Add support for reading connector type from PTYS")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Delete auxiliary bus drivers flow deletes the eth driver
first and then the eth-reps driver but eth-reps devices resources
are depend on eth device.

Fixed by changing the delete order of auxiliary bus drivers to delete
the eth-rep driver first and after it the eth driver.

Fixes: 601c10c8 ("net/mlx5: Delete custom device management logic")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

ct_label 0 is a default label each flow has and therefore
there can be rules that match on ct_label=0 without a prior
rule that set the ct_label to this value.

The ct_label value is not used directly in the HW rules and
instead it is mapped to some id within a defined range and this
id is used to set and match the metadata register which carries
the ct_label.

If we have a rule that matches on ct_label=0, the hw rule will
perform matching on a value that is != 0 because of the mapping
from label to id. Since the metadata register default value is
0 and it was never set before to anything else by an action that
sets the ct_label, there will always be a mismatch between that
register and the value in the rule.

To support such rule, a forced mapping of ct_label 0 to id=0
is done so that it will match the metadata register default
value of 0.

Fixes: 54b154ec ("net/mlx5e: CT: Map 128 bits labels to 32 bit map ID")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Commit 924a9bc3 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
added a call to dev_parse_header_protocol() but mac_header is not yet set.

This means that eth_hdr() reads complete garbage, and syzbot complained about it [1]

This patch resets mac_header earlier, to get more coverage about this change.

Audit of virtio_net_hdr_to_skb() callers shows that this change should be safe.

[1]

BUG: KASAN: use-after-free in eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
Read of size 2 at addr ffff888017a6200b by task syz-executor313/8409

CPU: 1 PID: 8409 Comm: syz-executor313 Not tainted 5.12.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:79 [inline]
 dump_stack+0x141/0x1d7 lib/dump_stack.c:120
 print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
 __kasan_report mm/kasan/report.c:399 [inline]
 kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
 eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
 dev_parse_header_protocol include/linux/netdevice.h:3177 [inline]
 virtio_net_hdr_to_skb.constprop.0+0x99d/0xcd0 include/linux/virtio_net.h:83
 packet_snd net/packet/af_packet.c:2994 [inline]
 packet_sendmsg+0x2325/0x52b0 net/packet/af_packet.c:3031
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:674
 sock_no_sendpage+0xf3/0x130 net/core/sock.c:2860
 kernel_sendpage.part.0+0x1ab/0x350 net/socket.c:3631
 kernel_sendpage net/socket.c:3628 [inline]
 sock_sendpage+0xe5/0x140 net/socket.c:947
 pipe_to_sendpage+0x2ad/0x380 fs/splice.c:364
 splice_from_pipe_feed fs/splice.c:418 [inline]
 __splice_from_pipe+0x43e/0x8a0 fs/splice.c:562
 splice_from_pipe fs/splice.c:597 [inline]
 generic_splice_sendpage+0xd4/0x140 fs/splice.c:746
 do_splice_from fs/splice.c:767 [inline]
 do_splice+0xb7e/0x1940 fs/splice.c:1079
 __do_splice+0x134/0x250 fs/splice.c:1144
 __do_sys_splice fs/splice.c:1350 [inline]
 __se_sys_splice fs/splice.c:1332 [inline]
 __x64_sys_splice+0x198/0x250 fs/splice.c:1332
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46

Fixes: 924a9bc3 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Balazs Nemeth <bnemeth@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not be advertising EEE for modes that we do not support,
correct that oversight by looking at the PHY device supported linkmodes.

Fixes: 99cec8a4 ("net: phy: broadcom: Allow enabling or disabling of EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A merge hint message needs some time to process before the merged
flow actually reaches the firmware, during which we may get duplicate
merge hints if there're more than one packet that hit the pre-merged
flow. And processing duplicate merge hints will cost extra host_ctx's
which are a limited resource.

Avoid the duplicate merge by using hash table to store the sub_flows
to be merged.

Fixes: 8af56f40 ("nfp: flower: offload merge flows")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the mentioned helper can end-up freeing the socket wmem
without waking-up any processes waiting for more write memory.

If the partially orphaned skb is attached to an UDP (or raw) socket,
the lack of wake-up can hang the user-space.

Even for TCP sockets not calling the sk destructor could have bad
effects on TSQ.

Address the issue using skb_orphan to release the sk wmem before
setting the new sock_efree destructor. Additionally bundle the
whole ownership update in a new helper, so that later other
potential users could avoid duplicate code.

v1 -> v2:
 - use skb_orphan() instead of sort of open coding it (Eric)
 - provide an helper for the ownership change (Eric)

Fixes: f6ba8d33 ("netem: fix skb_orphan_partial()")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_htb: fix null pointer dereference on a null new_q

Currently if new_q is null, the null new_q pointer will be
dereference when 'q->offload' is true. Fix this by adding
a braces around htb_parent_to_leaf_offload() to avoid it.

Addresses-Coverity: ("Dereference after null check")
Fixes: d03b195b ("sch_htb: Hierarchical QoS hardware offload")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qrtr_tx_wait does not check for radix_tree_insert failure, causing
the 'flow' object to be unreferenced after qrtr_tx_wait return. Fix
that by releasing flow on radix_tree_insert failure.

Fixes: 5fdeb0d3 ("net: qrtr: Implement outgoing flow control")
Reported-by: syzbot+739016799a89c530b32a@syzkaller.appspotmail.com
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, action creation using ACT API in replace mode is buggy.
When invoking for non-existent action index 42,

	tc action replace action bpf obj foo.o sec <xyz> index 42

kernel creates the action, fills up the netlink response, and then just
deletes the action after notifying userspace.

	tc action show action bpf

doesn't list the action.

This happens due to the following sequence when ovr = 1 (replace mode)
is enabled:

tcf_idr_check_alloc is used to atomically check and either obtain
reference for existing action at index, or reserve the index slot using
a dummy entry (ERR_PTR(-EBUSY)).

This is necessary as pointers to these actions will be held after
dropping the idrinfo lock, so bumping the reference count is necessary
as we need to insert the actions, and notify userspace by dumping their
attributes. Finally, we drop the reference we took using the
tcf_action_put_many call in tcf_action_add. However, for the case where
a new action is created due to free index, its refcount remains one.
This when paired with the put_many call leads to the kernel setting up
the action, notifying userspace of its creation, and then tearing it
down. For existing actions, the refcount is still held so they remain
unaffected.

Fortunately due to rtnl_lock serialization requirement, such an action
with refcount == 1 will not be concurrently deleted by anything else, at
best CLS API can move its refcount up and down by binding to it after it
has been published from tcf_idr_insert_many. Since refcount is atleast
one until put_many call, CLS API cannot delete it. Also __tcf_action_put
release path already ensures deterministic outcome (either new action
will be created or existing action will be reused in case CLS API tries
to bind to action concurrently) due to idr lock serialization.

We fix this by making refcount of newly created actions as 2 in ACT API
replace mode. A relaxed store will suffice as visibility is ensured only
after the tcf_idr_insert_many call.

Note that in case of creation or overwriting using CLS API only (i.e.
bind = 1), overwriting existing action object is not allowed, and any
such request is silently ignored (without error).

The refcount bump that occurs in tcf_idr_check_alloc call there for
existing action will pair with tcf_exts_destroy call made from the
owner module for the same action. In case of action creation, there
is no existing action, so no tcf_exts_destroy callback happens.

This means no code changes for CLS API.

Fixes: cae422f3 ("net: sched: use reference counting action init")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling ncsi_stop_channel_monitor from channel_monitor is a guaranteed
deadlock on SMP because stop calls del_timer_sync on the timer that
invoked channel_monitor as its timer function.

Recognise the inherent race of marking the monitor disabled before
deleting the timer by just returning if enable was cleared.  After
a timeout (the default case -- reset to START when response received)
just mark the monitor.enabled false.

If the channel has an entry on the channel_queue list, or if the
state is not ACTIVE or INACTIVE, then warn and mark the timer stopped
and don't restart, as the locking is broken somehow.

Fixes: 0795fb20 ("net/ncsi: Stop monitor if channel times out or is inactive")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace WARN_ONCE() that can be triggered from userspace with
pr_warn_once(). Those still give user a hint what's the issue.

I've left WARN()s that are not possible to trigger with current
code-base and that would mean that the code has issues:
- relying on current compat_msg_min[type] <= xfrm_msg_min[type]
- expected 4-byte padding size difference between
  compat_msg_min[type] and xfrm_msg_min[type]
- compat_policy[type].len <= xfrma_policy[type].len
(for every type)

Reported-by: syzbot+834ffd1afc7212eb8147@syzkaller.appspotmail.com
Fixes: 5f3eea6b ("xfrm/compat: Attach xfrm dumps to 64=>32 bit translator")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

In nfp_bpf_ctrl_msg_rx, if
nfp_ccm_get_type(skb) == NFP_CCM_TYPE_BPF_BPF_EVENT is true, the skb
will be freed. But the skb is still used by nfp_ccm_rx(&bpf->ccm, skb).

My patch adds a return when the skb was freed.

Fixes: bcf0cafa ("nfp: split out common control message handling code")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-03-29

This series contains updates to ice driver only.

Ani does not fail on link/PHY errors during probe as this is not a fatal
error to prevent the user from remedying the problem. He also corrects
checking Wake on LAN support to be port number, not PF ID.

Fabio increases the AdminQ timeout as some commands can take longer than
the current value.

Chinh fixes iSCSI to use be able to use port 860 by using information
from DCBx and other QoS configuration info.

Krzysztof fixes a possible race between ice_open() and ice_stop().

Bruce corrects the ordering of arguments in a memory allocation call.

Dave removes DCBNL device reset bit which is blocking changes coming
from DCBNL interface.

Jacek adds error handling for filter allocation failure.

Robert ensures memory is freed if VSI filter list issues are
encountered.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This binding file uses $ref: ethernet-controller.yaml# so it's required
to use "unevaluatedProperties" (instead of "additionalProperties") to
make Ethernet properties validate.

Fixes: f08b5cf1 ("dt-bindings: net: bcm4908-enet: include ethernet-controller.yaml")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The correct property name is "nvmem-cell-names". This is what:
1. Was originally documented in the ethernet.txt
2. Is used in DTS files
3. Matches standard syntax for phandles
4. Linux net subsystem checks for

Fixes: 9d3de3c5 ("dt-bindings: net: Add YAML schemas for the generic Ethernet options")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the if(skb_peek(arrvq) == skb) branch, it calls __skb_dequeue(arrvq) to get
the skb by skb = skb_peek(arrvq). Then __skb_dequeue() unlinks the skb from arrvq
and returns the skb which equals to skb_peek(arrvq). After __skb_dequeue(arrvq)
finished, the skb is freed by kfree_skb(__skb_dequeue(arrvq)) in the first time.

Unfortunately, the same skb is freed in the second time by kfree_skb(skb) after
the branch completed.

My patch removes kfree_skb() in the if(skb_peek(arrvq) == skb) branch, because
this skb will be freed by kfree_skb(skb) finally.

Fixes: cb1b7280 ("tipc: eliminate race condition at multicast reception")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accessing SGE_QBASE_MAP[0-3] and SGE_QBASE_INDEX registers can lead
to SGE missing doorbells under heavy traffic. So, only collect them
when adapter is idle. Also update the regdump range to skip collecting
these registers.

Fixes: 80a95a80 ("cxgb4: collect SGE PF/VF queue map")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>