Change the configuration logic for the VF driver to leverage the
ring-to-service mappings now received via PFVF.

While the driver config logic is not yet capable of supporting
configurations other than the default mapping, make sure that both VF
and PF share the same default configuration in order to work properly.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

In addition to retrieving the device capabilities, a VF may also need to
retrieve the mapping of its ring pairs to crypto and or compression
services in order to work properly.

Make the VF receive the ring-to-service mappings from the PF by means of a
new REQ_RING_SVC_MAP Block Message and add the request and response
logic on VF and PF respectively. This change requires to bump the PFVF
protocol to version 4.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The original design and current implementation of the PFVF protocol
expects the sender to both acquire and relinquish the ownership of the
shared CSR by setting and clearing the "in use" pattern on the remote
half of the register when sending a message. This happens regardless of
the acknowledgment of the reception, to guarantee changes, including
collisions, are surely detected.

However, in the case of a request that requires a response, collisions
can also be detected by the lack of a reply. This can be exploited to
speed up and simplify the above behaviour, letting the receiver both
acknowledge the message and release the CSR in a single transaction:

1) the sender can return as soon as the message has been acknowledged
2) the receiver doesn't have to wait long before acquiring ownership
of the CSR for the response message, greatly improving the overall
throughput.

Howerver, this improvement cannot be leveraged for fire-and-forget
notifications, as it would be impossible for the sender to clearly
distinguish between a collision and an ack immediately followed by a new
message.

This patch implements this optimization in a new version of the protocol
(v3), which applies the fast-ack logic only whenever possible and
guarantees backward compatibility with older versions. For requests, a
new retry loop guarantees a correct behaviour.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Allow the VF driver to get the supported device capabilities through PFVF,
by adding a new block message, the Capability Summary.

This messages allows to exchange the capability through masks, which
report, depending on the Capability Summary version, up to the following
information:
- algorithms and/or services that are supported by the device (e.g.
  symmetric crypto, data compression, etc.)
- (extended) compression capabilities, with details about the compression
  service (e.g. if compress and verify is supported by this device)
- the frequency of the device

This patch supports the latest Capabilities Summary version 3 for VFs,
but will limit support for the PF driver to version 2. This change also
increases the PFVF protocol to version 2.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

GEN2 devices use a single CSR for PFVF messages, which leaves up to 10 bits
of payload per single message. While such amount is sufficient for the
currently defined messages, the transfer of bigger and more complex data
streams from the PF to the VF requires a new mechanism that extends the
protocol.

This patch adds a new layer on top of the basic PFVF messaging, called
Block Messages, to encapsulate up to 126 bytes of data in a single
logical message across multiple PFVF messages of new types (SMALL,
MEDIUM and LARGE BLOCK), including (sub)types (BLKMSG_TYPE) to carry the
information about the actual Block Message.

Regardless of the size, each Block Message uses a two bytes header,
containing the version and size, to allow for extension while
maintaining compatibility. The size and the types of Block Messages are
defined as follow:

- small block messages:  up to 16 BLKMSG types of up to 30 bytes
- medium block messages: up to 8 BLKMSG types of up to 62 bytes
- large block messages:  up to 4 BLKMSG types of up to 126 bytes

It effectively works as reading a byte at a time from a block device and
for each of these new Block Messages:
- the requestor (always a VF) can either request a specific byte of the
  larger message, in order to retrieve the full message, or request the
  value of the CRC calculated for a specific message up to the provided
  size (to allow for messages to grow while maintaining forward
  compatibility)
- the responder (always the PF) will either return a single data or CRC
  byte, along with the indication of response type (or error).

This patch provides the basic infrastructure to perform the above
operations, without defining any new message.

As CRCs are required, this code now depends on the CRC8 module.

Note: as a consequence of the Block Messages design, sending multiple
PFVF messages in bursts, the interrupt rate limiting values on the PF are
increased.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This driver relies on either the FW (on the PF) or the PF (on the VF) to
know how crypto services and rings map to one another. Store this
information so that it can be referenced in the future at runtime for
checks or extensions.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds an entry for storing the PFVF protocol version for both
PF and VFs. While not currently used, knowing and storing the remote
protocol version enables more complex compatibility checks and/or newer
features for compatible PFVF endpoints in the future.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Review the ACK timings in adf_gen2_pfvf_send() to improve the latency
by reducing the polling interval. Also increase the timeout, for higher
tolerance in highly loaded systems, and reposition these new values to
allow for inclusion by the future GEN4 devices too.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Replace the polling loop, waiting for the remote end to acknowledge
the reception of the message, with the equivalent and standard
read_poll_timeout() in adf_gen2_pfvf_send().

Also, the use of the read_poll_timeout():
- implies the use of microseconds for the timings, so update the previous
  values from ms to us
- allows to leverage the return value for both success and error,
  removing the need for the reset of the 'ret' variable soon after the
  'start' label.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The PFVF protocol defines messages composed of a number of control
bitfields. Replace all the code setting and retrieving such bits
with the utilities from bitfield.h, to improve code quality and
readability.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This implementation of the PFVF protocol was designed around the GEN2
devices and its CSR format. In order to support future generations,
which come with differently sized fields, change the definition of the PFVF
message and make it abstract by means of a new pfvf_message struct. Also,
introduce some utilities to translate to and from the new message format
and the device specific CSR format.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

In this implementation of the PFVF protocol every egressing message must
include the ADF_PFVF_MSGORIGIN_SYSTEM flag. However, this flag can be set
on all the outbound messages just before sending them rather than at
message build time, as currently done.

Remove the unnecessary code duplication by setting the
ADF_PFVF_MSGORIGIN_SYSTEM flag only once at send time in
adf_gen2_pfvf_send().
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently PF and VF share the same send and receive logic for the PFVF
protocol. However, the inner behaviour still depends on the specific
direction, requiring a test to determine the if the sender is a PF or a
VF. Moreover the vf_nr parameter is only required for PF2VF messages and
ignored for the opposite direction.

Make the GEN2 send and recv completely direction agnostic, by calculating
and determining any direction specific input in the caller instead, and
feeding the send and the receive functions with the same arguments for
both PF and VF. In order to accommodate for this change, the API of the
pfvf_ops send and recv has been modified to remove any reference to vf_nr.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently PFVF messages are created upfront in the CSR format, that is
PF2VF messages starting from bit 0 and VF2PF from bit 16, and passed
along unmodified to the PFVF send function.

Refactor the code to allow the VF2PF messages to be built starting from
bit 0, as for the PF2VF messages. Shift the VF to PF messages just
before sending them, and refactor the send logic to handle messages
properly depending on the direction.

As a result all the messages are composed the same way regardless of
the direction.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add and use the new helper function adf_get_pmisc_base() where convenient.

Also:
- remove no longer shared variables
- leverage other utilities, such as GET_PFVF_OPS(), as a consequence
- consistently use the "pmisc_addr" name for the returned value of this
  new helper
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add support for triggering a HW reset of a specific ring pair.
Being a device specific feature, add it to the hw_device_data struct.

This feature is supported only by QAT GEN4 devices.

This patch is based on earlier work done by Zelin Deng.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Extended the capability detection logic for 4xxx devices.
Mask out unsupported algorithms and services based on the value read in
the fuse register.

This includes only capabilities for the crypto service.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Enhance the device capability detection for QAT GEN2 devices to detect if
a device supports the compression service.

This is done by checking both the fuse and the strap registers for c62x
and c3xxx and only the fuse register for dh895xcc.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Set the CIPHER capability for QAT GEN2 devices if the hardware supports
it. This is done if both the CIPHER and the AUTHENTICATION engines are
available on the device.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Get compression extended capabilities mask from firmware through the
init/admin channel.
These capabilities are stored in the accel_dev structure and will be
communicated to VF through the PFVF channel.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fix the following coccicheck warning:

./drivers/crypto/marvell/octeontx2/otx2_cptpf_ucode.c:1523:16-17:
WARNING opportunity for swap().
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Give the same priority of OMAP DES/3DES than OMAP AES for being sure it
is picked before software implementation.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Rather than passing all variables as modified, pass ones that are only
read into that parameter. This helps with old gcc versions when
alternatives are additionally used, and lets gcc's codegen be a little
bit more efficient. This also syncs up with the latest Vale/EverCrypt
output.
Reported-by: Mathias Krause <minipli@grsecurity.net>
Cc: Aymeric Fromherz <aymeric.fromherz@inria.fr>
Link: https://lore.kernel.org/wireguard/1554725710.1290070.1639240504281.JavaMail.zimbra@inria.fr/
Link: https://github.com/project-everest/hacl-star/pull/501Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

CN10K series of silicons support true random number
generators. This patch adds support for the same. Also
supports entropy health status checking.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Joseph Longever <jlongever@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Enable deflate/lz77_zstd algorithm for uacce device on Kunpeng930.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If the hardware reports the 'CQ' overflow or 'CQE' error by the abnormal
interrupt, disable the queue and stop tasks send to hardware.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If the hardware reports the event queue overflow by the abnormal interrupt,
the driver needs to reset the function and re-enable the event queue
interrupt and abnormal interrupt.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The abnormal interrupt method needs to be changed, and the changed method
needs to be locked in order to maintain atomicity. Therefore,
replace request_irq() with request_threaded_irq().
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

After processing an interrupt event and the interrupt function is
enabled by writing the QM_DOORBELL_CMD_AEQ register, the hardware
may generate new interrupt events due to processing other user's task
when the subsequent interrupt events have not been processed. The new
interrupt event will disrupt the current normal processing flow and
cause other problems.

Therefore, the operation of writing the QM_DOORBELL_CMD_AEQ doorbell
register needs to be placed after all interrupt events processing
are completed.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch does not change any code, just code movement. Preparing for
next patch.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The internal memory of the device needs to be reset only when
the device is globally initialized. Other scenarios, such as
function reset, do not need to perform reset.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When remove the driver and executing the task occur at the same time,
the following deadlock will be triggered:

Chain exists of:
    sva_lock --> uacce_mutex --> &qm->qps_lock
    Possible unsafe locking scenario:
		CPU0                    CPU1
		----                    ----
	lock(&qm->qps_lock);
					lock(uacce_mutex);
					lock(&qm->qps_lock);
	lock(sva_lock);

And the lock 'qps_lock' is used to protect qp. Therefore, it's reasonable
cycle is to continue until the qp memory is released. So move the release
lock infront of 'uacce_remove'.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

For Kunpeng 920, the bit 0 of register 'HZIP_SGL_RUSER_32_63' stand for
whether the ssid is valid. So this bit should be set as valid for sva mode.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

hpre_curve25519_src_init() allocates memory for 'ptr' before calling
memcmp(). If memcmp() returns 0, the function will return '-EINVAL'
without freeing memory.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.

Replace kernel.h inclusion with the list of what is really being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().

Link: https://github.com/KSPP/linux/issues/162Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().

Link: https://github.com/KSPP/linux/issues/162Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add new module parameter to allow users to use SEV_INIT_EX instead of
SEV_INIT. This helps users who lock their SPI bus to use the PSP for SEV
functionality. The 'init_ex_path' parameter defaults to NULL which means
the kernel will use SEV_INIT, if a path is specified SEV_INIT_EX will be
used with the data found at the path. On certain PSP commands this
file is written to as the PSP updates the NV memory region. Depending on
file system initialization this file open may fail during module init
but the CCP driver for SEV already has sufficient retries for platform
initialization. During normal operation of PSP system and SEV commands
if the PSP has not been initialized it is at run time. If the file at
'init_ex_path' does not exist the PSP will not be initialized. The user
must create the file prior to use with 32Kb of 0xFFs per spec.
Signed-off-by: David Rientjes <rientjes@google.com>
Co-developed-by: Peter Gonda <pgonda@google.com>
Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add psp_init_on_probe module parameter that allows for skipping the
PSP's SEV platform initialization during module init. User may decouple
module init from PSP init due to use of the INIT_EX support in upcoming
patch which allows for users to save PSP's internal state to file. The
file may be unavailable at module init.

Also moves the PSP ABI version log message to after successful PSP init
instead of module init in case this new parameter is used.
Signed-off-by: Peter Gonda <pgonda@google.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Create a helper function sev_fw_alloc() which can be used to allocate
aligned memory regions for use by the PSP firmware. Currently only used
for the SEV-ES TMR region but will be used for the SEV_INIT_EX NV memory
region.
Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>