- 07 Mar, 2017 3 commits
-
-
Chen-Yu Tsai authored
drm_vblank_init can fail due to insufficient memory. Ignoring the error and proceeding may cause the kernel to dereference an invalid pointer when vblank is enabled. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
The master bind function calls numerous drm functions which initialize underlying structures. It also tries to bind the various components of the display pipeline, some of which may add additional drm objects. This patch adds proper cleanup functions in the error path of the master bind function. This requires the patch "drm/sun4i: Move drm_mode_config_cleanup call to main driver", which splits out drm_mode_config_cleanup from sun4i_framebuffer_free so we can call it separately. Signed-off-by:
-
Chen-Yu Tsai authored
drm_mode_config_cleanup is the complement of drm_mode_config_init, which is called in the bind function of sun4i_drv. drm_mode_config_cleanup should be put in the unbind function to match. Signed-off-by:
-
- 02 Mar, 2017 4 commits
-
-
Eric Anholt authored
If a CMA allocation failed, the partially constructed BO would be unreferenced through the normal path, and we might choose to put it in the BO cache. If we then reused it before it expired from the cache, the kernel would OOPS. Signed-off-by:
Eric Anholt <eric@anholt.net> Fixes: c826a6e1 ("drm/vc4: Add a BO cache.") Reviewed-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170301185602.6873-2-eric@anholt.net
-
Eric Anholt authored
The from_cache flag was actually "the BO is invisible to userspace", so we can repurpose it to just zero out a cached BO and return it to userspace. Improves wall time for a loop of 5 glsl-algebraic-add-add-1 by -1.44989% +/- 0.862891% (n=28, 1 outlier removed from each that appeared to be other system noise) Note that there's an intel-gpu-tools test to check for the proper zeroing behavior here, which we continue to pass. Signed-off-by:
-
Daniel Vetter authored
This reverts commit 233ce881. I assumed it's ok, but really should have double-checked - CI caught tons of fail :( Cc: Jani Nikula <jani.nikula@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Acked-by:
Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170301171749.13053-1-daniel.vetter@ffwll.ch
-
Maxime Ripard authored
Implement legacy framebuffer ioctl FBIO_WAITFORVSYNC in the generic framebuffer emulation driver. Legacy framebuffer users like non kms/drm based OpenGL(ES)/EGL implementations may require the ioctl to synchronize drawing or buffer flip for double buffering. It is tested on the i.MX6. Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
- 01 Mar, 2017 33 commits
-
-
Gabriel Krisman Bertazi authored
Commit be7f735cd5ea ("drm: Rely on mode_config data for fb_helper initialization") dropped the num_crtc argument. Update the documentation to reflect that and prevent the kernel-doc warnings below: ./drivers/gpu/drm/drm_fb_cma_helper.c:557: warning: Excess function parameter 'num_crtc' description in 'drm_fbdev_cma_init' ./drivers/gpu/drm/drm_fb_cma_helper.c:558: warning: Excess function parameter 'num_crtc' description in 'drm_fbdev_cma_init' Fixes: be7f735cd5ea ("drm: Rely on mode_config data for fb_helper initialization") Signed-off-by:Gabriel Krisman Bertazi <krisman@collabora.co.uk> Signed-off-by:
-
Chris Zhong authored
Reference the power domain incase dw-mipi power down when in use. Signed-off-by:
Chris Zhong <zyw@rock-chips.com> Reviewed-by:
Sean Paul <seanpaul@chromium.org> Signed-off-by:
-
Chris Zhong authored
Set the lanes bps to 1 / 0.9 times of pclk, the margin is not enough for some panel, it will cause the screen display is not normal, so increases the badnwidth to 1 / 0.8. Signed-off-by:
-
Chris Zhong authored
Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Chris Zhong authored
The MIPI DSI do not need check the validity of resolution, the max resolution should depend VOP. Hence, remove rk3288_mipi_dsi_mode_valid here. Signed-off-by:
-
Chris Zhong authored
correct the coding style, according the checkpatch scripts Signed-off-by:
-
Chris Zhong authored
The vopb/vopl switch register of RK3399 mipi is different from RK3288, the default setting for mipi dsi mode is different too, so add a of_device_id structure to distinguish them, and make sure set the correct mode before mipi phy init. Signed-off-by:
Mark Yao <mark.yao@rock-chips.com> Reviewed-by:
-
Chris Zhong authored
The dw-mipi-dsi of rk3399 is almost the same as rk3288, the rk3399 has additional phy config clock. Signed-off-by:
-
John Keeping authored
In order to fully reset the state of the MIPI controller we must assert this reset. This is slightly more complicated than it could be in order to maintain compatibility with device trees that do not specify the reset property. Signed-off-by:
John Keeping <john@metanate.com> Reviewed-by:
-
John Keeping authored
Signed-off-by:
-
John Keeping authored
This ensures that the output resolution is known before fbcon loads. mipi_dsi_host_register() is moved above dw_mipi_dsi_register() to simplify error cleanup since the order of these operations does not matter. Signed-off-by:
-
John Keeping authored
When connected to the MIPI DSI output, we need to use N{H,V}SYNC for the internal connection but these flags are meaningless for DSI panels. Switch the test so that we do not set the P{H,V}SYNC bits unless the mode requires it. Signed-off-by: -
John Keeping authored
This matches other drivers. Signed-off-by:
-
John Keeping authored
As the documentation for readx_poll_timeout says, we want to use the specialized macro for readl rather than using the generic version directly. Signed-off-by:
-
John Keeping authored
The multiplication ratio for the PLL is required to be even due to the use of a "by 2 pre-scaler". Currently we are likely to end up with an odd multiplier even though there is an equivalent set of parameters with an even multiplier. For example, using the 324MHz bit rate with a reference clock of 24MHz we end up with M = 27, N = 2 whereas the example in the PHY databook gives M = 54, N = 4 for this bit rate and reference clock. By walking down through the available multiplier instead of up we are more likely to hit an even multiplier. With the above example we do now get M = 54, N = 4 as given by the databook. While doing this, change the loop limits to encode the actual limits on the divisor, which are: 40MHz >= (pllref / N) >= 5MHz Signed-off-by:
-
John Keeping authored
These values are specified as constant time periods but the PHY configuration is in terms of the current lane byte clock so using constant values guarantees that the timings will be outside the specification with some display configurations. Derive the necessary configuration from the byte clock in order to ensure that the PHY configuration is correct. Signed-off-by:
-
John Keeping authored
The bias, bandgap and PLL should all be configured before we enable them. Signed-off-by:
-
John Keeping authored
Also don't power up the DSI host at this point since this is not necessary in order to configure the PHY and we do so later when selecting video or command mode. Signed-off-by:
-
John Keeping authored
This clock rate is derived from the PHY PLL, so it should be calculated dynamically. This calculation is the same as that used by the vendor kernel and ensures that the escape clock runs at <20MHz as required by the MIPI specification. Signed-off-by:
-
John Keeping authored
Panel drivers may want to sent commands during the disable function, for example MIPI_DCS_SET_DISPLAY_OFF before the video signal ends. In order to send commands we need to write to registers, so pclk must be enabled. While changing this, remove the unnecessary code after the panel unprepare call which seems to be a workaround for a specific panel and thus belongs in the panel driver. Signed-off-by:
-
John Keeping authored
Some panels need to be configured with commands sent over the MIPI link, which they will do in the prepare hook. Call this after the PHY has been initialized so that we are able to send commands to the panel. Signed-off-by:
-
John Keeping authored
By dereferencing the MIPI command buffer as a u32* we rely on it being correctly aligned on ARM, but this may not be the case. Copy it into a stack variable that will be correctly aligned. Signed-off-by:
-
John Keeping authored
Requesting the HS clock from the PHY before we initialize it causes an invalid signal to be sent out since the input clock is not yet configured. The PHY databook suggests only asserting this signal when performing HS transfers, so let's do that. Signed-off-by:
-
John Keeping authored
Instead of always sending commands in LP mode, respect the MIPI_DSI_MSG_USE_LPM flag to decide how to send each message. Also request acks if MIPI_DSI_MSG_REQ_ACK is set. Signed-off-by:
-
John Keeping authored
As an aid to debugging. Signed-off-by:
-
John Keeping authored
As a side-effect of this, encode the endianness explicitly rather than casting a u16. Signed-off-by:
-
John Keeping authored
We want to check that both the GEN_CMD_EMPTY and GEN_PLD_W_EMPTY bits are set so we can't just check "val & mask" because that will be true if either bit is set. Signed-off-by:
-
John Keeping authored
In a couple of places here we use "val" for the value that is about to be written to a register but then reuse the same variable for the value of a status register before we get around to writing it. Rename the value to be written to so that we write the value we intend to and not what we have just read from the status register. Signed-off-by:
-
John Keeping authored
This is not needed since we can access the mode via the CRTC from the enable hook. Also remove the "mode" field that is no longer used. Signed-off-by:
-
John Keeping authored
This shows that we only use the mode from the enable function and prepares us to remove the "mode" field and the mode_set hook in the next commit. Signed-off-by:
-
John Keeping authored
With atomic modesetting the hardware will be powered off when the mode_set function is called. We should configure the hardware in the enable function, which is the atomic version of "commit" so let's use the enable hook rather than commit while we're at it. Signed-off-by:
-
Manasi Navare authored
If link training at a link rate optimal for a particular mode fails during modeset's atomic commit phase, then we let the modeset complete and then retry. We save the link rate value at which link training failed, update the link status property to "BAD" and use a lower link rate to prune the modes. It will redo the modeset on the current mode at lower link rate or if the current mode gets pruned due to lower link constraints then, it will send a hotplug uevent for userspace to handle it. This is also required to pass DP CTS tests 4.3.1.3, 4.3.1.4, 4.3.1.6. v9: * Use the trimmed max values of link rate/lane count based on link train fallback (Daniel Vetter) v8: * Set link_status to BAD first and then call mode_valid (Jani Nikula) v7: Remove the redundant variable in previous patch itself v6: * Obtain link rate index from fallback_link_rate using the helper intel_dp_link_rate_index (Jani Nikula) * Include fallback within intel_dp_start_link_train (Jani Nikula) v5: * Move set link status to drm core (Daniel Vetter, Jani Nikula) v4: * Add fallback support for non DDI platforms too * Set connector->link status inside set_link_status function (Jani Nikula) v3: * Set link status property to BAd unconditionally (Jani Nikula) * Dont use two separate variables link_train_failed and link_status to indicate same thing (Jani Nikula) v2: * Squashed a few patches (Jani Nikula) Acked-by:
Tony Cheng <tony.cheng@amd.com> Acked-by:
Harry Wentland <Harry.wentland@amd.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Manasi Navare authored
This fixes the kernel doc warning that was introduced in the 'commit 40ee6fbe ("drm: Add a new connector atomic property for link status")'. Description has been added for the enum values. Signed-off-by:
-
