- 22 Feb, 2011 3 commits
-
-
Eliad Peller authored
for debugging purposes, wl12xx determines whether a rx packet is a beacon packet. however, it checks only the frame_control subtype without checking the actual packet type, which leads to false identification in some cases. use ieee80211_is_beacon instead. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Gery Kahn authored
In revision > 6.1.3.0.0 the firmware expects memory configuration command as part of boot. This was missing if driver boots in PLT mode. The patch adds the memory configuration command, which fixes PLT commands tx continuous and rx statistics. Signed-off-by: Gery Kahn <geryk@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Dan Carpenter authored
ret is used to store int types. Using an u8 will break the error handling. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
- 21 Feb, 2011 29 commits
-
-
Sujith Manoharan authored
Commit "ath9k_hw: add an extra delay when reseting AR_RTC_RESET" added an extra udelay to the reset routine. As the required delay is already present, remove this. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
RA-Shiang Tu authored
Add new RT5390 chip support Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Shiang Tu authored
Revise/Add GPIO register related definitions Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Shiang Tu authored
Make the definition of protection related registers more precisely Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
This reverts commit e81e0aef "rt2x00 : avoid timestamp for monitor injected frame." as it breaks proper timestamp insertion into probe responses injected by hostapd for example. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Benoit PAPILLAULT <benoit.papillault@free.fr> Cc: Alban Browaeys <prahal@yahoo.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Only devices that don't have RTS/CTS offload need to check for IEEE80211_TX_RC_USE_RTS_CTS and IEEE80211_TX_RC_USE_CTS_PROTECT. By swapping both conditions we keep the same number of needed conditionals for devices without RTS/CTS offload but save one conditional on devices with RTS/CTS offload. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
RA-Jay Hung authored
TX_PWR_CFG_* setting need to consider below cases -compesate 20M/40M tx power delta for 2.4/5GHZ band -limit maximum EIRP tx power to power_level of regulatory requirement Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
RA-Jay Hung authored
For RT3070/RT3090/RT3390 with RX antenna diversity support, we must select default antenna using gpio control way even if we do not turn on antenna diversity feature. Seperate the meaning of TX/RX chain and antenna. Some chips use 2x2 TX/RX chain but may have 3 RX antennas or 1x1 TX/RX chain but may have 2 RX antennas to do antenna diversity. Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
The original code has many macros that are no longer needed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
Drivers rtlwifi, and rtl8192ce generate a large number of sparse warnings. This patch fixes most of them. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
Modify Kconfig and Makefile to build rtl8192cu. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
George authored
Add routine rtlwifi/rtl8192cu/trx.c. This routine differs from the rtl8192ce file of the same name. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
George authored
Add rtlwifi/rtl8192cu/table.c. These tables are different than the ones used in rtl8192ce. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
George authored
Add rtlwifi/rtl8192cu/rf.c. This routine is distinct from the one in rtl8192ce with the same name. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
George authored
Add the routine rtlwifi/rtl8192cu/phy.c. Most of the code is included from rtlwifi/rtl8192c/phy_common.c. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
George authored
Add the routine rtlwifi/rtl8192cu/hw.c. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
George authored
Add the routine rtlwifi/rtl8192cu/hw.c. This one is distinct from the routine of the same name in rtl8192ce. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
George authored
Add the rtlwifi/rtl8192cu routines for dm.c, fw.c, led.c and sw.c. Where possible, these routines use the corresponding code in rtl8192ce. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
Move common routines from rtlwifi/rtl8192ce/phy.c and .../rtl8192cu/phy.c into rtlwifi/rtl8192c/phy_common.c. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
Further merge of parameters needed for rtl8192cu. In addition, some changes needed for rtl8192se and rtl8192de are included and additional Hungarian notation is removed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
George authored
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: George <george0505@realtek.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
Modify some rtl8192ce routines for merging with rtl8192cu. In addition, remove some usage of Hungarian notation. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
This change modifies rtlwifi/rtl8192ce/def.h to handle rtl8192cu. In addition, a couple of routines needed for both drivers are converted to be inline. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
This change modifies rtlwifi/rtl8192ce/reg.h to support rtl8192cu. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vasanthakumar Thiagarajan authored
When op_flush() is called with no drop (drop=false), the driver tries to tx as many frames as possible in about 100ms on every hw queue. During this time period frames from sw queue are also scheduled on to respective hw queue. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Randy Dunlap authored
The wl12xx sdio_test code uses wl12xx_get_platform_data, which is only present when WL12*_SDIO is enabled, so make WL12XX_SDIO_TEST depend on WL12XX_SDIO so that the needed interface will be present. sdio_test.c:(.devinit.text+0x13178): undefined reference to `wl12xx_get_platform_data' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Luciano Coelho <luciano.coelho@nokia.com> Cc: Roger Quadros <roger.quadros@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wojciech Dubowik authored
Enable recognition of AR2315 chipsets in ath5k driver. Reported-by: Simon Morgenthaler <s.morgenthaler@students.unibe.ch> Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Christian Lamparter authored
AR9170USB will be replaced by carl9170 in the foreseeable future [2.6.40]. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 18 Feb, 2011 8 commits
-
-
ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6John W. Linville authored
Conflicts: drivers/bluetooth/ath3k.c drivers/bluetooth/btusb.c
-
Vivek Natarajan authored
Clear IEEE80211_STA_NULLFUNC_ACKED flag on disabling power save. Without this fix, there is a chance of setting CONF_PS before sending nullfunc frame. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
Initialize caldata to avoid compilation warning. CC [M] drivers/net/wireless/ath/ath9k/htc_drv_main.o drivers/net/wireless/ath/ath9k/htc_drv_main.c: In function ‘ath9k_htc_config’: drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: warning: ‘caldata’ may be used uninitialized in this function drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: note: ‘caldata’ was declared here Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jan Beulich authored
"def_bool n" without prompt is pointless, this should be just "bool". Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Christian Lamparter authored
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-