- 13 Jun, 2017 40 commits
-
-
Kevin Barnett authored
make the queue depth for LVs the same as the maximum I/Os supported by the controller Reviewed-by:
Scott Benesh <scott.benesh@microsemi.com> Signed-off-by:
Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by:
Don Brace <don.brace@microsemi.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Kevin Barnett authored
constrain resource usage during kdump to avoid kdump failures Reviewed-by:
-
Kevin Barnett authored
change return value for controller offline to be consistent with the rest of the driver. Reviewed-by:
-
Kevin Barnett authored
add support for PTRAID devices Reviewed-by:
-
Kevin Barnett authored
Reviewed-by:
-
Kevin Barnett authored
- improve some error messages. Reviewed-by:
-
Kevin Barnett authored
Reviewed-by:
-
Kevin Barnett authored
- remove debug code that is no longer necessary. - Some WARN_ON checks were removed because the driver continues to function when the conditions are met. - remove a MACRO that is no longer used. - remove unnecessary multi-line statements. Reviewed-by: -
Kevin Barnett authored
correct the BMIC Identify Physical Device structure - missing 2 fields Reviewed-by:
-
Kevin Barnett authored
eliminate redundant error message during initialization if the controller has crashed. Reviewed-by:
-
Kevin Barnett authored
make all variable names for pointers to struct pci_dev consistent throughout the driver. Reviewed-by:
-
Kevin Barnett authored
Add check for controller lockup during waits for synchronous controller commands. Reviewed-by:
-
Kevin Barnett authored
add workaround for BDMA hardware bug that can cause hw to read up to 12 SGL elements (192 bytes) beyond the last element in the list. This fix avoids IOMMU violations Reviewed-by:
-
Kevin Barnett authored
check for controller lockups Reviewed-by:
-
Kevin Barnett authored
add support for ACPI S3 (suspend) and S4 (hibernate) system power states. Reviewed-by:
-
Kevin Barnett authored
- Block all I/O targeted at LUN reset device. - Wait until all I/O targeted at LUN reset device has been consumed by the controller. - Issue LUN reset request. - Wait until all outstanding I/Os and LUN reset completion have been received by the host. - Return to OS results of LUN reset request. Reviewed-by:
-
Kevin Barnett authored
Only register for controller events that driver supports cleanup event handling. Reviewed-by:
-
Kevin Barnett authored
put in SIS mode during initialization. support kexec/kdump Reviewed-by:
Scott Teel <scott.teel@microsemi.com> Signed-off-by:
-
Kevin Barnett authored
tell smartpqi controller to generate a checkpoint for rare lockup conditions. Reviewed-by:
-
Kevin Barnett authored
add support for setting PCIe completion timeout. Reviewed-by:
-
Kevin Barnett authored
minor cleanup of interrupt initialization and tear-down. Reviewed-by:
-
Kevin Barnett authored
correct a problem caused by holding a spinlock during device deletion. Reviewed-by:
-
Don Brace authored
Reviewed-by:
-
Don Brace authored
- simplify the driver - there are a lot of quirky racy conditions not handled - causes more aborts/resets when the number of commands to be aborted is large, such as in multi-path fail-overs. - has been turned off in our internal driver since 8/31/2015 Reviewed-by:
-
Don Brace authored
- Block I/O requests with 0 length transfers which go down the ioaccel path. This causes lockup issues down in the basecode. - These issues have been fixed, but there are customers who are experiencing the issues when running older firmware. Reviewed-by:
-
Scott Teel authored
create new worker thread to monitor controller events - both the rescan and event monitor workers can cause a rescan to occur however for multipath we have found that we need to respond faster than the normal scheduled rescan interval for path fail-overs. - getting controller events only involves reading a register, but the rescan worker can obtain an updated LUN list when there is a PTRAID device present. - move common code to a separate function. advantages: - detect controller events more frequently. - leave rescan thread interval at 30 seconds. Reviewed-by:
-
Don Brace authored
- queue depth assignment not in correct place, had no effect. Reviewed-by:
-
Don Brace authored
- mark device state sooner. Reviewed-by:
-
Don Brace authored
- call scsi_done when the command completes. Reviewed-by:
-
Don Brace authored
- schedule another scan. - mark current scan as completed. Reviewed-by:
-
Don Brace authored
Prevent enclosure resets. Reviewed-by:
Scott Teel <scott.tell@microsemi.com> Reviewed-by:
-
Don Brace authored
Use the return from TUR as a check for the device state. Reviewed-by:
-
Don Brace authored
external shelves do not support BMICs. Reviewed-by:
-
Don Brace authored
- align with latest spec. - added __attribute((aligned(512))) Reviewed-by:
-
Raghava Aditya Renukunta authored
Update the driver version to 50834 Signed-off-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by:
David Carroll <david.carroll@microsemi.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
Remove reference to Series-9 HBA and created arc ctrl check function. Signed-off-by:
Prasad B Munirathnam <prasad.munirathnam@microsemi.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
Added info and error messages in controller reset function to log information about the status of the IOP/SOFT reset. Signed-off-by:
-
Raghava Aditya Renukunta authored
Make sure that IOP and SOFT reset are enabled for both for both arc and hba1000 controllers. Signed-off-by:
-
Raghava Aditya Renukunta authored
Made sure that ioctl commands return in case of a controller reset. Signed-off-by:
-
Raghava Aditya Renukunta authored
The command thread checks the ctrl health periodically before sending updates to the controller. The function that it uses is aac_check_health which does more than get the health status. Signed-off-by:
-
