Do camera capture test on i.MX6q sabresd board, and save the capture data to
nfs rootfs. The command is:
gst-launch-1.0 -e imxv4l2src device=/dev/video1 num-buffers=2592000 ! tee name=t !
queue ! imxv4l2sink sync=false t. ! queue ! vpuenc ! queue ! mux. pulsesrc num-buffers=3720937
blocksize=4096 ! 'audio/x-raw, rate=44100, channels=2' ! queue ! imxmp3enc ! mpegaudioparse !
queue ! mux. qtmux name=mux ! filesink location=video_recording_long.mov

After about 10 hours running, there have net watchdog timeout kernel dump:
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:264 dev_watchdog+0x2b4/0x2d8()
NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.24-01051-gdb840b7 #440
[<80014e6c>] (unwind_backtrace) from [<800118ac>] (show_stack+0x10/0x14)
[<800118ac>] (show_stack) from [<806ae3f0>] (dump_stack+0x78/0xc0)
[<806ae3f0>] (dump_stack) from [<8002b504>] (warn_slowpath_common+0x68/0x8c)
[<8002b504>] (warn_slowpath_common) from [<8002b558>] (warn_slowpath_fmt+0x30/0x40)
[<8002b558>] (warn_slowpath_fmt) from [<8055e0d4>] (dev_watchdog+0x2b4/0x2d8)
[<8055e0d4>] (dev_watchdog) from [<800352d8>] (call_timer_fn.isra.33+0x24/0x8c)
[<800352d8>] (call_timer_fn.isra.33) from [<800354c4>] (run_timer_softirq+0x184/0x220)
[<800354c4>] (run_timer_softirq) from [<8002f420>] (__do_softirq+0xc0/0x22c)
[<8002f420>] (__do_softirq) from [<8002f804>] (irq_exit+0xa8/0xf4)
[<8002f804>] (irq_exit) from [<8000ee5c>] (handle_IRQ+0x54/0xb4)
[<8000ee5c>] (handle_IRQ) from [<80008598>] (gic_handle_irq+0x28/0x5c)
[<80008598>] (gic_handle_irq) from [<800123c0>] (__irq_svc+0x40/0x74)
Exception stack(0x80d27f18 to 0x80d27f60)
7f00:                                                       80d27f60 0000014c
7f20: 8858c60e 0000004d 884e4540 0000004d ab7250d0 80d34348 00000000 00000000
7f40: 00000001 00000000 00000017 80d27f60 800702a4 80476e6c 600f0013 ffffffff
[<800123c0>] (__irq_svc) from [<80476e6c>] (cpuidle_enter_state+0x50/0xe0)
[<80476e6c>] (cpuidle_enter_state) from [<80476fa8>] (cpuidle_idle_call+0xac/0x154)
[<80476fa8>] (cpuidle_idle_call) from [<8000f174>] (arch_cpu_idle+0x8/0x44)
[<8000f174>] (arch_cpu_idle) from [<80064c54>] (cpu_startup_entry+0x100/0x158)
[<80064c54>] (cpu_startup_entry) from [<80cd8a9c>] (start_kernel+0x304/0x368)
---[ end trace 09ebd32fb032f86d ]---
...

There might have a race in napi_schedule(), leaving interrupts disabled forever.
After these patch, the case still work more than 40 hours running.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After d75b1ade (net: less interrupt
masking in NAPI) the napi instance is removed from the per-cpu list
prior to calling the n->poll(), and is only requeued if all of the
budget was used.  This inadvertently broke netfront because netfront
does not use NAPI correctly.

If netfront had not used all of its budget it would do a final check
for any Rx responses and avoid calling napi_complete() if there were
more responses.  It would still return under budget so it would never
be rescheduled.  The final check would also not re-enable the Rx
interrupt.

Additionally, xenvif_poll() would also call napi_complete() /after/
enabling the interrupt.  This resulted in a race between the
napi_complete() and the napi_schedule() in the interrupt handler.  The
use of local_irq_save/restore() avoided by race iff the handler is
running on the same CPU but not if it was running on a different CPU.

Fix both of these by always calling napi_compete() if the budget was
not all used, and then calling napi_schedule() if the final checks
says there's more work.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The encap->type comes straight from Netlink. Validate it against
max supported encap types just like ip_encap_hlen() already does.

Fixes: a8c5f9 ("ip_tunnel: Ops registration for secondary encap (fou, gue)")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The symbols are exported and could be used by external modules.

Fixes: a8c5f9 ("ip_tunnel: Ops registration for secondary encap (fou, gue)")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
pull request: wireless 2014-12-16

Please pull this batch of fixes intended for the 3.19 stream!

For the Bluetooth bits, Johan says:

"The patches consist of:

 - Coccinelle warning fix
 - hci_dev_lock/unlock fixes
 - Fixes for pending mgmt command handling
 - Fixes for properly following the force_lesc_support switch
 - Fix for a Microsoft branded Broadcom adapter
 - New device id for Atheros AR3012
 - Fix for BR/EDR Secure Connections enabling"

Along with that...

Brian Norris avoids leaking some kernel memory contents via printk in brcmsmac.

Julia Lawall corrects some misspellings in a few drivers.

Larry Finger gives us one more rtlwifi fix to correct a porting oversight.

Wei Yongjun fixes a sparse warning in rtlwifi.

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise we get things like:

warning: (NET_DSA_BCM_SF2 && BCMGENET && SYSTEMPORT) selects FIXED_PHY which has unmet direct dependencies (NETDEVICES && PHYLIB=y)

In order to make this work we have to rename fixed.c to fixed_phy.c
because the regulator drivers already have a module named "fixed.o".
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael S. Tsirkin says:

====================
tun/macvtap: TUNSETIFF fixes

Dan Carpenter reported the following:
	static checker warning:

		drivers/net/tun.c:1694 tun_set_iff()
		warn: 0x17100 is larger than 16 bits

	drivers/net/tun.c
	  1692
	  1693          tun->flags = (tun->flags & ~TUN_FEATURES) |
	  1694                  (ifr->ifr_flags & TUN_FEATURES);
	  1695

	It's complaining because the "ifr->ifr_flags" variable is a short
	(should it be unsigned?).  The new define:

	#define IFF_VNET_LE    0x10000

	doesn't fit in two bytes.  Other suspect looking code could be:

		return __virtio16_to_cpu(q->flags & IFF_VNET_LE, val);

And that's true: we have run out of IFF flags in tun.

So let's not try to add more: add simple GET/SET ioctls
instead. Easy to test, leads to clear semantics.

Alternatively we'll have to revert the whole thing for 3.19,
but that seems more work as this has dependencies
in other places.

While here, I noticed that macvtap was actually reading
ifreq flags as a 32 bit field.
Fix that up as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Everyone should use TUNSETVNETLE/TUNGETVNETLE instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use TUNSETVNETLE/TUNGETVNETLE instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use TUNSETVNETLE/TUNGETVNETLE instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ifreq flags field is only 16 bit wide, so setting IFF_VNET_LE there has
no effect:
doesn't fit in two bytes.

The tests passed apparently because they have an even number of bugs,
all cancelling out.

Luckily we didn't release a kernel with this flag, so it's
not too late to fix this.

Add TUNSETVNETLE/TUNGETVNETLE to really achieve the purpose
of IFF_VNET_LE.

This has an added benefit that if we ever want a BE flag,
we won't have to deal with weird configurations like
setting both LE and BE at the same time.

IFF_VNET_LE will be dropped in a follow-up patch.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

flags field in ifreq is only 16 bit wide, but
we read it as a 32 bit value.
If userspace doesn't zero-initialize unused fields,
this will lead to failures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: broadcom: fix FIXED_PHY dependencies

This patch series removes the bogus "select FIXED_PHY if FOO=y" that I have
been using in GENET, SYSTEMPORT and the SF2 DSA switch driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to do the following:

select FIXED_PHY if NET_DSA_BCM_SF2=y, as this implies that we will not be
able to build and/or run the driver correctly when built as a module,
which is no longer an issue since commit 37e9a690 ("net: phy: export
fixed_phy_register()").

Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to do the following:

select FIXED_PHY if SYSTEMPORT=y, as this implies that we will not be able
to build and/or run the driver correctly when built as a module, which
is no longer an issue since commit 37e9a690 ("net: phy: export
fixed_phy_register()")

Fixes: a3862db2 ("net: systemport: hook SYSTEMPORT driver in the build")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to do the following:

select FIXED_PHY if BCMGENET=y, as this implies that we will not be able
to build and/or run the driver correctly when built as a module, which
is no longer an issue since commit 37e9a690 ("net: phy: export
fixed_phy_register()")

Fixes: b0ba512e225d ("net: bcmgenet: enable driver to work without device tree"
Fixes: bdaa53bd ("net: bcmgenet: hook into the build system")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The setting of this flag was missed in previous modifications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Debug code prints the fifo name via custom dev_warn() wrappers. The
fifo_names array is only non-zero when debugging is manually enabled,
which is all well and good. However, it's *not* good that this array
uses zero-length arrays in the non-debug case, and so it doesn't
actually have any memory allocated to it. This means that as far as we
know, fifo_names[i] actually points to garbage memory.

I've seen this in my log:

[ 4601.205511] brcmsmac bcma0:1: wl0: brcms_c_d11hdrs_mac80211: �GeL txop exceeded phylen 137/256 dur 1602/1504

So let's give this array space enough to fill it with a NULL byte.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list@broadcom.com
Cc: netdev@vger.kernel.org
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixes the following sparse warning:

drivers/net/wireless/rtlwifi/rtl8192cu/hw.c:1595:6: warning:
 symbol 'usb_cmd_send_packet' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Replace a misspelled function name by %s and then __func__.

8821 was written as 8812.

This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Replace a misspelled function name by %s and then __func__.

This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Replace a misspelled function name by %s and then __func__.

This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Cyrille Pitchen says:

====================
net/macb: fix multiqueue support patch up

This series of patches is a fixup for the multiqueue support patch.

The first patch fixes a bug introduced by the multiqueue support patch.
The second one doesn't fix a bug but simplify the source code by removing
useless calls to devm_free_irq() since we use managed device resources for
IRQs.

They were applied on the net-next tree and tested with a sama5d36ek board.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Inside macb_probe(), when devm_request_irq() fails on queue q, there is no need
to call devm_free_irq() on queues 0..q-1 because the managed device resources
are released later when calling free_netdev().

Also removing devm_free_irq() call from macb_remove() for the same reason.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix a bug introduced by the multiqueue support patch:
"net/macb: add TX multiqueue support for gem"

the "bp" pointer to the netdev private data was dereferenced and used after the
associated memory had been freed by calling free_netdev().
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/rds/message.c: In function ‘rds_message_inc_copy_to_user’:
net/rds/message.c:328: warning: comparison of distinct pointer types lacks a cast

Use min_t(unsigned long, ...) like is done in
rds_message_copy_from_user().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If CONFIG_OF is not set:

drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c: In function ‘sti_dwmac_parse_data’:
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c:318: warning: ‘rs’ is used uninitialized in this function

of_property_read_string() will return -ENOSYS in this case, and rs will
be an uninitialized pointer.

While the fallback clock selection is already selected correctly in this
case, the string comparisons should be skipped too, else the system will
crash while dereferencing the uninitialized pointer.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If GPIOLIB=n the following build errors occur:

drivers/net/ethernet/smsc/smc91x.c: In function 'try_toggle_control_gpio':
drivers/net/ethernet/smsc/smc91x.c:2204:2: error: implicit declaration of function 'devm_gpiod_get_index' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2204:7: warning: assignment makes pointer from integer without a cast [enabled by default]
drivers/net/ethernet/smsc/smc91x.c:2213:2: error: implicit declaration of function 'gpiod_direction_output' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2216:3: error: implicit declaration of function 'devm_gpiod_put' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2222:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]

Fix this by letting the driver depend on GPIOLIB if OF is selected.

Fixes: 7d2911c4 ("net: smc91x: Fix gpios for device tree based booting")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NBMA GRE tunnels temporarily push GRE header that contain the
per-packet NBMA destination on the skb via header ops early in xmit
path. It is the later pulled before the real GRE header is constructed.

The inner mac was thus set differently in nbma case: the GRE header
has been pushed by neighbor layer, and mac header points to beginning
of the temporary gre header (set by dev_queue_xmit).

Now that the offloads expect mac header to point to the gre payload,
fix the xmit patch to:
 - pull first the temporary gre header away
 - and reset mac header to point to gre payload

This fixes tso to work again with nbma tunnels.

Fixes: 14051f04 ("gre: Use inner mac length when computing tunnel length")
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: Tom Herbert <therbert@google.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the typo, there should be "It".
On the other hand, fix whitespace errors detected by checkpatch.pl
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To be future-proof and for better readability the time comparisons are
modified to use time_before, time_after, and time_after_eq instead of
plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 driver fixes for 3.19-rc1

Just fixes for two small issues introduced in the 3.19 merge window
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To support asymmetric EQ allocations, we should query the device
capabilities prior to enabling SRIOV. As a side effect of adding that,
we are dumping the PF device capabilities twice. Avoid that by moving
the printing into a helper function which is called once.

Fixes: 7ae0e400 ('net/mlx4_core: Flexible (asymmetric) allocation of
		     EQs and MSI-X vectors for PF/VFs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current mlx4_load_one has a memory leak as it always allocates
dev_cap, but frees it only on error.

In addition, even if VFs exist when mlx4_load_one is called,
we still need to notify probed VFs that we're loading (by
incrementing pf_loading).

Fixes: a0eacca9 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull security layer updates from James Morris:
 "In terms of changes, there's general maintenance to the Smack,
  SELinux, and integrity code.

  The IMA code adds a new kconfig option, IMA_APPRAISE_SIGNED_INIT,
  which allows IMA appraisal to require signatures.  Support for reading
  keys from rootfs before init is call is also added"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (23 commits)
  selinux: Remove security_ops extern
  security: smack: fix out-of-bounds access in smk_parse_smack()
  VFS: refactor vfs_read()
  ima: require signature based appraisal
  integrity: provide a hook to load keys when rootfs is ready
  ima: load x509 certificate from the kernel
  integrity: provide a function to load x509 certificate from the kernel
  integrity: define a new function integrity_read_file()
  Security: smack: replace kzalloc with kmem_cache for inode_smack
  Smack: Lock mode for the floor and hat labels
  ima: added support for new kernel cmdline parameter ima_template_fmt
  ima: allocate field pointers array on demand in template_desc_init_fields()
  ima: don't allocate a copy of template_fmt in template_desc_init_fields()
  ima: display template format in meas. list if template name length is zero
  ima: added error messages to template-related functions
  ima: use atomic bit operations to protect policy update interface
  ima: ignore empty and with whitespaces policy lines
  ima: no need to allocate entry for comment
  ima: report policy load status
  ima: use path names cache
  ...

Pull char/misc driver updates from Greg KH:
 "Here's the big char/misc driver update for 3.19-rc1

  Lots of little things all over the place in different drivers, and a
  new subsystem, "coresight" has been added.  Full details are in the
  shortlog"

* tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits)
  parport: parport_pc, do not remove parent devices early
  spmi: Remove shutdown/suspend/resume kernel-doc
  carma-fpga-program: drop videobuf dependency
  carma-fpga: drop videobuf dependency
  carma-fpga-program.c: fix compile errors
  i8k: Fix temperature bug handling in i8k_get_temp()
  cxl: Name interrupts in /proc/interrupt
  CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning
  coresight-replicator: remove .owner field for driver
  coresight: fixed comments in coresight.h
  coresight: fix typo in comment in coresight-priv.h
  coresight: bindings for coresight drivers
  coresight: Adding ABI documentation
  w1: support auto-load of w1_bq27000 module.
  w1: avoid potential u16 overflow
  cn: verify msg->len before making callback
  mei: export fw status registers through sysfs
  mei: read and print all six FW status registers
  mei: txe: add cherrytrail device id
  mei: kill cached host and me csr values
  ...

Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core update from Greg KH:
 "Here's the set of driver core patches for 3.19-rc1.

  They are dominated by the removal of the .owner field in platform
  drivers.  They touch a lot of files, but they are "simple" changes,
  just removing a line in a structure.

  Other than that, a few minor driver core and debugfs changes.  There
  are some ath9k patches coming in through this tree that have been
  acked by the wireless maintainers as they relied on the debugfs
  changes.

  Everything has been in linux-next for a while"

* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
  Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
  fs: debugfs: add forward declaration for struct device type
  firmware class: Deletion of an unnecessary check before the function call "vunmap"
  firmware loader: fix hung task warning dump
  devcoredump: provide a one-way disable function
  device: Add dev_<level>_once variants
  ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
  ath: use seq_file api for ath9k debugfs files
  debugfs: add helper function to create device related seq_file
  drivers/base: cacheinfo: remove noisy error boot message
  Revert "core: platform: add warning if driver has no owner"
  drivers: base: support cpu cache information interface to userspace via sysfs
  drivers: base: add cpu_device_create to support per-cpu devices
  topology: replace custom attribute macros with standard DEVICE_ATTR*
  cpumask: factor out show_cpumap into separate helper function
  driver core: Fix unbalanced device reference in drivers_probe
  driver core: fix race with userland in device_add()
  sysfs/kernfs: make read requests on pre-alloc files use the buffer.
  sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
  fs: sysfs: return EGBIG on write if offset is larger than file size
  ...

Pull tty/serial driver updates from Greg KH:
 "Here's the big tty/serial driver update for 3.19-rc1.

  There are a number of TTY core changes/fixes in here from Peter Hurley
  that have all been teted in linux-next for a long time now.  There are
  also the normal serial driver updates as well, full details in the
  changelog below"

* tag 'tty-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (219 commits)
  serial: pxa: hold port.lock when reporting modem line changes
  tty-hvsi_lib: Deletion of an unnecessary check before the function call "tty_kref_put"
  tty: Deletion of unnecessary checks before two function calls
  n_tty: Fix read_buf race condition, increment read_head after pushing data
  serial: of-serial: add PM suspend/resume support
  Revert "serial: of-serial: add PM suspend/resume support"
  Revert "serial: of-serial: fix up PM ops on no_console_suspend and port type"
  serial: 8250: don't attempt a trylock if in sysrq
  serial: core: Add big-endian iotype
  serial: samsung: use port->fifosize instead of hardcoded values
  serial: samsung: prefer to use fifosize from driver data
  serial: samsung: fix style problems
  serial: samsung: wait for transfer completion before clock disable
  serial: icom: fix error return code
  serial: tegra: clean up tty-flag assignments
  serial: Fix io address assign flow with Fintek PCI-to-UART Product
  serial: mxs-auart: fix tx_empty against shift register
  serial: mxs-auart: fix gpio change detection on interrupt
  serial: mxs-auart: Fix mxs_auart_set_ldisc()
  serial: 8250_dw: Use 64-bit access for OCTEON.
  ...

Pull USB updates from Greg KH:
 "Here's the big set of USB and PHY patches for 3.19-rc1.

  The normal churn in the USB gadget area is in here, as well as xhci
  and other individual USB driver updates.  The PHY tree is also in
  here, as there were dependancies on the USB tree.

  All of these have been in linux-next"

* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
  arm: omap3: twl: remove usb phy init data
  usbip: fix error handling in stub_probe()
  usb: gadget: udc: missing curly braces
  USB: mos7720: delete some unneeded code
  wusb: replace memset by memzero_explicit
  usbip: remove unneeded structure
  usb: xhci: fix comment for PORT_DEV_REMOVE
  xhci: don't use the same variable for stopped and halted rings current TD
  xhci: clear extra bits from slot context when setting max exit latency
  xhci: cleanup finish_td function
  USB: adutux: NULL dereferences on disconnect
  usb: chipidea: fix platform_no_drv_owner.cocci warnings
  usb: chipidea: Fixed a few typos in comments
  Documentation: bindings: add doc for the USB2 ChipIdea USB driver
  usb: chipidea: add a usb2 driver for ci13xxx
  usb: chipidea: fix phy handling
  usb: chipidea: remove duplicate dev_set_drvdata for host_start
  usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
  usb: chipidea: add controller reset API
  usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
  ...