The alsa driver uses videobuf low-level functions that are not
available in vb2, so replace them by driver-specific functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Move these fields from cx23885_fh to cx23885_dev.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

There is no overlay support, so drop these unused fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This information is available elsewhere as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Currently no radio device nodes are ever created, so remove the dead radio
code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

If field format is not valid, map it as V4L2_FIELD_INTERLACED,
instead of pretending to support an invalid format.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Fix v4l2-compliance failure relating to formatting.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Convert the -417 source to the control framework as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This is part 1, converting the uncompressed video/vbi nodes to use
the control framework.

The next patch converts the compressed video node as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Enable core locking which allows us to safely switch to unlocked_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add support for struct v4l2_fh and priority handling.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Fix a bunch of v4l2-compliance errors relating to audio input handling.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Set device_caps to fix the v4l2-compliance QUERYCAP complaints.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Those non-static functions aren't used anywhere yet. Comment them
while they're unused.

Solves the following warnings:

drivers/media/platform/vivid/vivid-vid-out.c:1120:5: warning: no previous prototype for 'vivid_vid_out_g_edid' [-Wmissing-prototypes]
 int vivid_vid_out_g_edid(struct file *file, void *_fh,
     ^
drivers/media/platform/vivid/vivid-vid-out.c:1152:5: warning: no previous prototype for 'vivid_vid_out_s_edid' [-Wmissing-prototypes]
 int vivid_vid_out_s_edid(struct file *file, void *_fh,
     ^

Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Removes the following warnings:

drivers/media/platform/vivid/vivid-core.c:581:2: warning: initialized field overwritten [-Woverride-init]
  .vidioc_overlay   = vidioc_overlay,
  ^
drivers/media/platform/vivid/vivid-core.c:581:2: warning: (near initialization for 'vivid_ioctl_ops.vidioc_overlay') [-Woverride-init]
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

That remove a few warnings:

drivers/media/platform/vivid/vivid-kthread-out.c:226:5: warning: no previous prototype for 'vivid_start_generating_vid_out' [-Wmissing-prototypes]
 int vivid_start_generating_vid_out(struct vivid_dev *dev, bool *pstreaming)
     ^
drivers/media/platform/vivid/vivid-kthread-out.c:260:6: warning: no previous prototype for 'vivid_stop_generating_vid_out' [-Wmissing-prototypes]
 void vivid_stop_generating_vid_out(struct vivid_dev *dev, bool *pstreaming)
      ^
drivers/media/platform/vivid/vivid-kthread-cap.c:806:5: warning: no previous prototype for 'vivid_start_generating_vid_cap' [-Wmissing-prototypes]
 int vivid_start_generating_vid_cap(struct vivid_dev *dev, bool *pstreaming)
     ^
drivers/media/platform/vivid/vivid-kthread-cap.c:841:6: warning: no previous prototype for 'vivid_stop_generating_vid_cap' [-Wmissing-prototypes]
 void vivid_stop_generating_vid_cap(struct vivid_dev *dev, bool *pstreaming)
      ^
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The vivid driver is a vastly superior test driver, so just drop the old
vivi driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Update the Kconfig and Makefile files so this driver can be compiled.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This fixes a compilation error with allyesconfig:

drivers/media/platform/exynos-gsc/built-in.o: In function `get_format':
(.text+0x12f5): multiple definition of `get_format'
drivers/media/platform/vivid/built-in.o:(.text+0x4bf4): first defined here
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This adds support for an SDR capture device. It generates simple
sine/cosine waves. The code for that has been contributed by
Antti.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This adds radio receiver and transmitter support. Part of that is common
to both and so is placed in the radio-common source.

These drivers also support RDS. In order to generate valid RDS data a
simple RDS generator is implemented in rds-gen.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The test patterns for video capture are generated by this code. All patterns
are precalculated taking into account colorspace information, pixel and video
aspect ratios and scaling information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

In order to test capture and output overlays a simple framebuffer
device is created. It's bare bone, but it does the job.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add the kthread handlers for video/vbi capture and video/vbi output.
These carefully control the rate at which frames are generated (video
capture) and accepted (video output). While the short-term jitter is
around the order of a jiffie, in the long term the rate matches the
configured framerate exactly.

The capture thread handler also takes care of the video looping and
of capture and overlay support. This is probably the most complex part
of this driver due to the many combinations of crop, compose and scaling
on the input and output, and the blending that has to be done if
overlay support is enabled as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This adds support for VBI capture (raw and sliced) and VBI output
(raw and sliced) to the vivid driver. In addition a VBI generator
is added that generates simple VBI data in either sliced or raw
format.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This adds the ioctl and vb2 queue support for video capture and output.
Part of this is common to both, so that is placed in a vid-common source.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The vivid-ctrls code sets up and processes the various V4L2 controls
that are needed by this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This is the core driver code that creates all the driver instances
and all the configured devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The vivid Virtual Video Test Driver helps testing V4L2 applications
and can emulate V4L2 hardware. Add the documentation for this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

If this is a multiplanar buf_type and the plane we want to read has a
non-zero data_offset, then that data_offset was not taken into account.

Note that read() or write() for formats with more than one plane is currently
not allowed, hence the use of 'planes[0]' since this is only relevant for a
single-plane format.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Fix coding style issues pointed out by checkpatch.pl.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add some error checking and implement functionality a little bit
differently.

Cc: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Fix coding style issues pointed out by checkpatch.pl.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Maximum satellite symbol rate used is 45000000Sps which overflows
when multiplied by 135. As final calculation result is fraction,
we could use mult_frac macro in order to keep calculation inside
32 bit number limits and prevent overflow.

Original bug and fix was provided by Nibble Max. I decided to
implement it differently as it is now.
Reported-by: Nibble Max <nibble.max@gmail.com>
Tested-by: Nibble Max <nibble.max@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

There is no need to keep local copy of usb_device pointer as we
have same pointer stored and available easily from device state.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Reported by Dan Carpenter:

The patch d10d1b9a: "[media] dvb_usb_v2: use dev_* logging
macros" from Jun 26, 2012, leads to the following Smatch complaint:

drivers/media/usb/dvb-usb-v2/dvb_usb_urb.c:31 dvb_usb_v2_generic_io()
	 error: we previously assumed 'd' could be null (see line 29)

...
Remove whole check as it must not happen in any case. Driver is
totally broken if it does not have valid pointer to device.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Set the property for delivery system also in case of SYS_ATSC. This
behaviour is observed in the sniffs taken with Hauppauge HVR-955Q
Windows driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

DVB-T2 PLP selection implemented for Si2168 demod.
Tested with PCTV 292e.
Signed-off-by: Evgeny Plehov <EvgenyPlehov@ukr.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Read MAC address from the EEPROM.

This version two corrects a flaw in the result code returning that
did exist in the first version.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

TechnoTrend TT-connect CT2-4650 CI (0b48:3012) is an USB DVB-T2/C tuner with
the following components:

 USB interface: Cypress CY7C68013A-56LTXC
 Demodulator: Silicon Labs Si2168-A20
 Tuner: Silicon Labs Si2158-A20
 CI chip: CIMaX SP2HF

The firmware for the tuner is the same as for TechnoTrend TT-TVStick CT2-4400.
See https://www.mail-archive.com/linux-media@vger.kernel.org/msg76944.html

The demodulator needs a firmware that can be extracted from the Windows drivers.
File ttConnect4650_64.sys should be extracted from
http://www.tt-downloads.de/bda-treiber_4.1.0.4.zip (MD5 sum below).

3464bfc37a47b4032568718bacba23fb  ttConnect4650_64.sys

Then the firmware can be extracted:
dd if=ttConnect4650_64.sys ibs=1 skip=273376 count=6424 of=dvb-demod-si2168-a20-01.fw

The SP2 CI module requires a definition of a function cxusb_tt_ct2_4650_ci_ctrl
that is passed on to the SP2 driver and called back for CAM operations.

[crope@iki.fi: meld USB ID define patch to this]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>