This adds TMU (Time Management Unit) support for Intel BXT platform.
It enables the alarm wake-up functionality in the TMU unit of Whiskey Cove
PMIC.
Signed-off-by: Nilesh Bacchewar <nilesh.bacchewar@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[andy: resolve merge conflict in Kconfig]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Like other Y700 models Lenovo Y700 15-ACZ does not have a physical rfkill switch.
ideapad-laptop wrongly reports all radios as blocked by hardware which causes
wireless network connections to fail.

Add this model without an rfkill switch to the no_hw_rfkill list.
Signed-off-by: Artiom Vaskov <velemas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The Surface 3 is not following the ACPI spec for PNP0C40, but nearly.
The device is connected to a I2C device that might have some magic
but we don't know about.
Just create the device after the enumeration and use the declared GPIOs
to provide button support.

This driver is just an adaptation of drivers/input/misc/soc_button_array.c

The Surface Pro 3 is using an ACPI driver and matches against the bid
of the device ("VGBI"). To prevent this incompatible driver to be used
on the Surface Pro, we add a match on the Surface 3 bid "TEV2".

link: https://bugzilla.kernel.org/show_bug.cgi?id=102761Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The LID state provided by ACPI on the Surface 3 is not accurate.
The ACPI node doesn't get notified on LID open, which means the
LID input switch stays close most of the time.

Fortunatelly, there is a WMI method which directly queries the
GPIO underneath the LID state, so it's far more reliable than ACPI.
To get the notifications that the LID was opened/closed, we can
rely on the ACPI notification of the touchscreen: the DSDT shows
that the touchscreen will get notified on close/open as it also
controls its _STA method.

Note that we need to set the tag "power-switch" to the LID
input node through a udev rule for logind to accept it:

SUBSYSTEM=="input", KERNEL=="event*", KERNELS=="surface3-wmi", \
	TAG+="power-switch"
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add calls for mlxcpld-hotplug platform driver registration/unregistration
and add platform hotplug data configurations. This driver, when registered
within system will handle system hot-plug events for the power suppliers,
power cables and fans (insertion and removing). These events are
controlled through CPLD Lattice device.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

drivers/platform/x86/mlx-platform.c:219:2-3: Unneeded semicolon

 Remove unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci

CC: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Since mlx-platform is not an architectural driver, it is moved out
of arch/x86/platform to drivers/platform/x86.
Relevant Makefile and Kconfig are updated.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

linux-next reported in_tablet_mode and type may be used uninitialized
after:

b3180028 ("platform/x86: thinkpad_acpi: Move tablet detection into separate function")

This turns out to be a false positive as the pr_info call cannot be
reached if tp_features.hotkey_tablet (global scope) is 0, and
in_tablet_mode and type are assigned in both places
tp_features.hotkey_tablet is assigned.

Regardless, to make it explicit and avoid further reports, initialize
in_tablet_mode to 0 and type to NULL.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Lyude <lyude@redhat.com>

kbd_led_level_set uses dell_smbios call which blocks, so the kbd_led
classdev should use the brightness_set_blocking callback.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

Fix an [-Wold-style-declaration] GCC warning by moving the inline
keyword before the return type.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

Recently we met an issue on lots of Lenovo thinkpad laptops (those
laptops are not released to market yet), the issue is that the
thinkpad_acpi.ko can't be automatically loaded as before.

Through debugging, we found the HKEY_HID is LEN0268 instead of
LEN0068 on those machines, and the MHKV is 0x200 instead of
0x100. So adding the new ID into the driver.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

For whatever reason, the X1 Yoga doesn't support the normal method of
querying for tablet mode. Instead of providing the MHKG method under the
hotkey handle, we're instead given the CMMD method under the EC handle.
Values on this handle are either 0x1, laptop mode, or 0x6, tablet mode.
Tested-by: Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Lyude <lyude@redhat.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

The hotkey events and ACPI handles used for detecting tablet mode on a
few of the newer thinkpad models (Yoga X1 and the Yoga 260 specifically)
have been changed around, so unfortunately this means we're definitely
going to need to probe for multiple types of tablet mode support. Since
the hotkey_init() is already a lot larger than it should be, let's split
up this detection into its own function to make things a little easier
to read.

As well, since we're going to have multiple types of tablet modes, make
hotkey_tablet into an enum so we can also use it to indicate the type of
tablet mode reporting the machine supports.

Suggested by Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Lyude <lyude@redhat.com>
Cc: Daniel Martin <consume.noise@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

Without this patch, the Asus X45U wireless card can't be turned
on (hard-blocked), but after a suspend/resume it just starts working.

Following this bug report[1], there are other cases like this one, but
this Asus is the only model that I can test.

[1] https://ubuntuforums.org/showthread.php?t=2181558

Cc: stable@vger.kernel.org # 4.4.x-
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Make use of dmi->ident as other drivers do, like fujitsu, intel,
hp and samsung.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The bluetooth adapter Atheros AR3012 can't be enumerated
and make the bluetooth function broken.

T:  Bus=02 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3362 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

The error is:

 usb 2-6: device not accepting address 7, error -62
 usb usb2-port6: unable to enumerate USB device

It is caused by adapter's connected port is mapped to xHC
controller, but the xHCI is not supported by the usb device.

The output of 'sudo lspci -nnxxx -s 00:14.0':

 00:14.0 USB controller [0c03]: Intel Corporation 8 Series USB xHCI HC [8086:9c31] (rev 04)
 00: 86 80 31 9c 06 04 90 02 04 30 03 0c 00 00 00 00
 10: 04 00 a0 f7 00 00 00 00 00 00 00 00 00 00 00 00
 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 1f 20
 30: 00 00 00 00 70 00 00 00 00 00 00 00 0b 01 00 00
 40: fd 01 36 80 89 c6 0f 80 00 00 00 00 00 00 00 00
 50: 5f 2e ce 0f 00 00 00 00 00 00 00 00 00 00 00 00
 60: 30 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 70: 01 80 c2 c1 08 00 00 00 00 00 00 00 00 00 00 00
 80: 05 00 87 00 0c a0 e0 fe 00 00 00 00 a1 41 00 00
 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 a0: 00 01 04 00 00 00 00 00 00 00 00 00 00 00 00 00
 b0: 0f 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00
 c0: 03 c0 30 00 00 00 00 00 03 0c 00 00 00 00 00 00
 d0: f9 01 00 00 f9 01 00 00 0f 00 00 00 0f 00 00 00
 e0: 00 08 00 00 00 00 00 00 00 00 00 00 d8 d8 00 00
 f0: 00 00 00 00 00 00 00 00 b1 0f 04 08 00 00 00 00

By referencing Intel Platform Controller Hub(PCH) datasheet,
the xHC USB 2.0 Port Routing(XUSB2PR) at offset 0xD0-0xD3h
decides the setting of mapping the port to EHCI controller or
xHC controller. And the port mapped to xHC will enable xHCI
during bus resume.

The setting of disabling bluetooth adapter's connected port is
0x000001D9. The value can be obtained by few times 1 bit flip
operation. The suited configuration should have the 'lsusb -t'
result with bluetooth using ehci:

/:  Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 5000M
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/9p, 480M
    |__ Port 5: Dev 2, If 0, Class=Video, Driver=uvcvideo, 480M
    |__ Port 5: Dev 2, If 1, Class=Video, Driver=uvcvideo, 480M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/8p, 480M
        |__ Port 6: Dev 3, If 0, Class=Wireless, Driver=btusb, 12M
        |__ Port 6: Dev 3, If 1, Class=Wireless, Driver=btusb, 12M
Signed-off-by: Kai-Chuan Hsieh <kai.chiuan@gmail.com>
Acked-by: Corentin Chary <corentin.chary@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[andy: resolve merge conflict in asus-wmi.h]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Fix:

  drivers/platform/x86/intel_mid_thermal.c:424:12: warning: ‘mid_thermal_resume’
  defined but not used [-Wunused-function]
   static int mid_thermal_resume(struct device *dev)
              ^
  drivers/platform/x86/intel_mid_thermal.c:436:12: warning: ‘mid_thermal_suspend’
  defined but not used [-Wunused-function]
   static int mid_thermal_suspend(struct device *dev)
              ^

which I see during randbuilds here.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Darren Hart <dvhart@infradead.org>
Cc: platform-driver-x86@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Use devm_input_allocate_device to simplify the error handling code.
This conversion also makes input_register_device() to be called after
acpi_remove_notify_handler. This avoid a small window that it's possible
to call notify_handler after unregister input device.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Use ACPI_FAILURE() to replace !ACPI_SUCCESS(), this avoid !! operations.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The Dell Rugged 7202 has 3 programmable buttons (labeled P1, P2, P3)
and a detachable keyboard/mouse dock.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Wifi catcher is a slider switch, that when slid past the on position
will emit an event that is intended for launching a wifi application
or applet when the machine is turned on.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

This patch adds Kabylake CPU support for pmc_core driver.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

SPT LTR_IGN register provides a means to make the PMC ignore the LTR values
reported by the individual PCH devices.

echo <IP Offset> > /sys/kernel/debug/pmc_core/ltr_ignore.

When a particular IP Offset bit is set the PMC will ignore the LTR value
reported by the corresponding IP when the PMC performs the latency
coalescing.

IP Offset	IP Name
0		SPA
1		SPB
2		SATA
3		GBE
4		XHCI
5		RSVD
6		ME
7		EVA
8		SPC
9		Azalia/ADSP
10		RSVD
11		LPSS
12		SPD
13		SPE
14		Camera
15		ESPI
16		SCC
17		ISH
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
[dvhart: pmc_core_ltr_ignore_write local declaration order cleanup]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

ModPhy Common lanes can provide the clock gating status for the important
system PLLs such as Gen2 USB3PCIE2 PLL, DMIPCIE3 PLL, SATA PLL and MIPI
PLL.

On SPT, in addition to the crystal oscillator clock, the 100Mhz Gen2
USB3PCI2 PLL clock is used as the PLL reference clock and Gen2 PLL idling
is a necessary condition for the platform to go into low power states like
PC10 and S0ix.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

The PCH implements a number of High Speed I/O (HSIO) lanes that are split
between PCIe*, USB 3.0, SATA, GbE, USB OTG and SSIC. This patch shows the
current power gating status of the available ModPhy Core lanes. This is
done by sending a message to the PMC (MTPMC) that contains the XRAM
register offset for the MPHY_CORE_STS_0 and MPHY_CORE_STS_1 and then by
reading the response sent by the PMC (MFPMC).

While enabling low power modes we often encounter situations when the
ModPhy lanes are not power gated and it becomes hard to debug which lane is
active and which is not in the absence of an external hardware debugger
(JTAG/ITP). This patch eliminates the dependency on an external hardware
debugger for reading the ModPhy Lanes power gating status.

This patch requires PMC_READ_DISABLE setting to be disabled in the platform
bios.

cat /sys/kernel/debug/pmc_core/mphy_lanes_power_gating_status
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch adds the support for reading the power gating status of various
devices present on Sunrise Point PCH. This is intended to be used for
debugging purpose while tuning the platform for power optimizations and
also to understand which devices (on PCH) are blocking the system to enter
a low power state.

Power Management Controller on Sunrise Point PCH provides access to "PGD
PFET Enable Ack Status Registers (ppfear)". This patch reads and decodes
this register and dumps the output in formatted manner showing various
devices present on the PCH and their "Power Gating" status.

Further documentation can be found in Intel 7th Gen Core family mobile u/y
processor io datasheet volume 2.

Sample output (stripped and not in order):

cat /sys/kernel/debug/pmc_core/pch_ip_power_gating_status
PMC				State: Not Power gated
OPI-DMI				State: Not Power gated
XHCI				State: Power gated
LPSS				State: Power gated
CSME_PSF			State: Not power gated
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

On Sunrise Point PCH, the Power Management Controller provides 4K bytes of
memory space for various power management and debug registers. This fix is
needed to access power management & debug registers that are mapped at a
higher offset.

Also, this provides a fix for correctly masking the PWRMBASE as the initial
bits (0-11) are reserved.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

The AMW0_GUID1 wmi is not only found on Acer family but also other
machines like Lenovo, Fujitsu and Medion. In the past, acer-wmi handled
those non-Acer machines by quirks list.

But actually acer-wmi driver was loaded on any machine that had
AMW0_GUID1. This behavior is strange because those machines should be
supported by appropriate wmi drivers. e.g. fujitsu-laptop,
ideapad-laptop.

This patch adds the logic to check the machine that has AMW0_GUID1
should be in Acer/Packard Bell/Gateway white list. But, it still keeps
the quirk list of those supported non-acer machines for backward
compatibility.
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

Enable system support for the Mellanox Technologies hotplug platform
driver, which provides support for the next Mellanox basic systems:
"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410",
"msb7800", "msn2740", "msn2100" and also various number of derivative
systems from the above basic types.
This driver handles hot-plug events for the power suppliers, power
cables and fans for the above systems.

The Kconfig currently controlling compilation of this code is:
driver/platform/x86:config MLX_CPLD_PLATFORM
                       tristate "Mellanox platform hotplug driver support"
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

Merge tag 'platform-drivers-x86-v4.9-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver fixes from Darren Hart:
 "Fix a Kconfig issue leading potential link failure, and add a DMI
  match for an existing quirk.

  asus-wmi:
   - add SERIO_I8042 dependency

  ideapad-laptop:
   - Add Lenovo Yoga 910-13IKB to no_hw_rfkill dmi list"

* tag 'platform-drivers-x86-v4.9-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  platform/x86: asus-wmi: add SERIO_I8042 dependency
  platform/x86: ideapad-laptop: Add Lenovo Yoga 910-13IKB to no_hw_rfkill dmi list

Pull arch/sh updates from Rich Felker:
 "Minor changes to improve J2 support and match Kconfig expectations of
  other subsystems"

* tag 'sh-for-4.9' of git://git.libc.org/linux-sh:
  sh: add earlycon support to j2_defconfig
  sh: add Kconfig option for J-Core SoC core drivers
  sh: support CPU_J2 when compiler lacks -mj2

Pull scheduler fix from Ingo Molnar:
 "This fixes a group scheduling related performance/interactivity
  regression introduced in v4.8, which affects certain hardware
  environments where cpu_possible_mask != cpu_present_mask"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix incorrect task group ->load_avg

Pull HID fixes from Jiri Kosina:

 - hid-dr regression fix for certain dragonrise gamepads (device ID
   0079:0006), from Ioan-Adrian Ratiu

 - dma-on-stack fix for hid-led driver, from Heiner Kallweit

 - quirk for Akai MIDImix device

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: add quirk for Akai MIDImix.
  Revert "HID: dragonrise: fix HID Descriptor for 0x0006 PID"
  HID: hid-dr: add input mapping for axis selection
  HID: hid-led: fix issue with transfer buffer not being dma capable

Pull first round of pin control fixes from Linus Walleij:

 - a bunch of barnsjukdomar/kinderkrankheiten/maladie infantile in the
   Aspeed driver. (Why doesn't English have a word for this?)

   [ Maybe "teething problems" is the closest English idiom? - Linus T ]

 - fix a lockdep bug on the Intel BayTrail.

 - fix a few special laptop issues on the Intel pin controller solving
   suspend issues.

* tag 'pinctrl-v4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: intel: Only restore pins that are used by the driver
  pinctrl: baytrail: Fix lockdep
  pinctrl: aspeed-g5: Fix pin association of SPI1 function
  pinctrl: aspeed-g5: Fix GPIOE1 typo
  pinctrl: aspeed-g5: Fix names of GPID2 pins
  pinctrl: aspeed: "Not enabled" is a significant mux state

We have a fairly common pattern where you print several things as
continuations on one single line in a loop, and then at the end you do

	printk(KERN_CONT "\n");

to flush the buffered output.

But if the output was flushed by something else (concurrent printk
activity, or just system logging), we don't want that final flushing to
just print an empty line.

So just suppress empty continuation lines when they couldn't be merged
into the line they are a continuation of.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge the gup_flags cleanups from Lorenzo Stoakes:
 "This patch series adjusts functions in the get_user_pages* family such
  that desired FOLL_* flags are passed as an argument rather than
  implied by flags.

  The purpose of this change is to make the use of FOLL_FORCE explicit
  so it is easier to grep for and clearer to callers that this flag is
  being used.  The use of FOLL_FORCE is an issue as it overrides missing
  VM_READ/VM_WRITE flags for the VMA whose pages we are reading
  from/writing to, which can result in surprising behaviour.

  The patch series came out of the discussion around commit 38e08854
  ("mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing"),
  which addressed a BUG_ON() being triggered when a page was faulted in
  with PROT_NONE set but having been overridden by FOLL_FORCE.
  do_numa_page() was run on the assumption the page _must_ be one marked
  for NUMA node migration as an actual PROT_NONE page would have been
  dealt with prior to this code path, however FOLL_FORCE introduced a
  situation where this assumption did not hold.

  See

      https://marc.info/?l=linux-mm&m=147585445805166

  for the patch proposal"

Additionally, there's a fix for an ancient bug related to FOLL_FORCE and
FOLL_WRITE by me.

[ This branch was rebased recently to add a few more acked-by's and
  reviewed-by's ]

* gup_flag-cleanups:
  mm: replace access_process_vm() write parameter with gup_flags
  mm: replace access_remote_vm() write parameter with gup_flags
  mm: replace __access_remote_vm() write parameter with gup_flags
  mm: replace get_user_pages_remote() write/force parameters with gup_flags
  mm: replace get_user_pages() write/force parameters with gup_flags
  mm: replace get_vaddr_frames() write/force parameters with gup_flags
  mm: replace get_user_pages_locked() write/force parameters with gup_flags
  mm: replace get_user_pages_unlocked() write/force parameters with gup_flags
  mm: remove write/force parameters from __get_user_pages_unlocked()
  mm: remove write/force parameters from __get_user_pages_locked()
  mm: remove gup_flags FOLL_WRITE games from __get_user_pages()

This removes the 'write' argument from access_process_vm() and replaces
it with 'gup_flags' as use of this function previously silently implied
FOLL_FORCE, whereas after this patch callers explicitly pass this flag.

We make this explicit as use of FOLL_FORCE can result in surprising
behaviour (and hence bugs) within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This removes the 'write' argument from access_remote_vm() and replaces
it with 'gup_flags' as use of this function previously silently implied
FOLL_FORCE, whereas after this patch callers explicitly pass this flag.

We make this explicit as use of FOLL_FORCE can result in surprising
behaviour (and hence bugs) within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This removes the 'write' argument from __access_remote_vm() and replaces
it with 'gup_flags' as use of this function previously silently implied
FOLL_FORCE, whereas after this patch callers explicitly pass this flag.

We make this explicit as use of FOLL_FORCE can result in surprising
behaviour (and hence bugs) within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This removes the 'write' and 'force' from get_user_pages_remote() and
replaces them with 'gup_flags' to make the use of FOLL_FORCE explicit in
callers as use of this flag can result in surprising behaviour (and
hence bugs) within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>