This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.

This patch is necessary to access dwc2 registers correctly on big-endian
systems such as the mips based SoCs made by Lantiq. Then dwc2 can be
used to replace ifx-hcd driver for Lantiq platforms found e.g. in
OpenWrt.

The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h

Some files were then hand-edited to fix checkpatch.pl warnings about
too long lines.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

USB network adapters support Jumbo frames. The only thing blocking
that feature is the code in the gadget driver that disposes of
packets larger than 1518 bytes, and the limit on the ioctl to set
the mtu.

This patch relaxes these limits, and allows up to 15k frames sizes.
The 15k value was chosen because 16k does not work on all platforms,
and usingclose to 16k will result in allocating 5 or 8 4k pages to
store the skb, wasting pages at no measurable performance gain.

On a topic-miami board (Zynq-7000), iperf3 performance reports:
MTU= 1500, PC-to-gadget: 139 Mbps, Gadget-to-PC: 116 Mbps
MTU=15000, PC-to-gadget: 239 Mbps, Gadget-to-PC: 361 Mbps

On boards with slower CPUs the performance improvement will be
relatively much larger, e.g. an OMAP-L138 increased from 40 to
220 Mbps using a similar patch on an  2.6.37 kernel.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Felipe Balbi <balbi@ti.com>

struct at91_udc_data is now only used inside the driver, move it to its
include.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add snps,quirk-frame-length-adjustment property which provides value
for post silicon frame length adjustment
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

[un]register_interest and reading cable state by
name have been deprecated. Switch to new API.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Set musb config->maximum_speed based on the dts setting to control musb
speed.

By default musb works in high-speed mode. Adding

	maximum-speed = "full-speed";

to dts usb node will force musb to full-speed mode.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Set the Power register HSENAB bit based on musb->config->maximum_speed,
so that the glue layer can control MUSB to work in high- or full-speed.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

f_midi is not checking whether there is an error on usb_ep_queue
request, ignoring potential problems, such as memory leaks.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Instead of allowing a range of 2 to 4 requests,
let's allow the user choose up to 32 requests
as that will give us a better chance of keeping
controller busy.

We still maintain default of 2 so users shouldn't
be affected.
Signed-off-by: Felipe Balbi <balbi@ti.com>

We shouldn't return -EBUSY, that's used only internally
when the core still has transfers in flight on a given
endpoint.

Also, combine the error reporting so that we don't have
to duplicate it.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Instead of clearing DWC3_PENDING_REQUEST when
we start transfer, let's do it when the request
is actually queued, that way we know for sure
that we're clearing in the right time.
Signed-off-by: Felipe Balbi <balbi@ti.com>

In an attempt to make dwc3 slightly faster, let's
start usb_requests as soon as they come as that will
let us avoid a XFER_NOT_READY event and save a little
bit of time.
Signed-off-by: Felipe Balbi <balbi@ti.com>

by moving trace_dwc3_ep_queue() from dwc3_gadget_ep_queue()
to __dwc3_gadget_ep_queue() after usb_request is properly
initialized, makes for a better output always showing a
request with 0 actual and -115 (-EINPROGRESS) status.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Pull x86 fixes from Thomas Gleixner:
 "Two bugfixes from Andy addressing at least some of the subtle NMI
  related wreckage which has been reported by Sasha Levin"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/nmi/64: Fix a paravirt stack-clobbering bug in the NMI code
  x86/paravirt: Replace the paravirt nop with a bona fide empty function

Pull irq fix from Thomass Gleixner:
 "A bugfix for the atmel aic5 irq chip driver which caches the wrong
  data and thereby breaking resume"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/atmel-aic5: Use per chip mask caches in mask/unmask()

Pull ARM fixes from Russell King:
 "Just two fixes: wire up the new system calls added during the last
  merge window, and fix another user access site"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: alignment: fix alignment handling for uaccess changes
  ARM: wire up new syscalls

Pull ARM SoC fixes from Olof Johansson:
 "Our first real batch of fixes this release cycle.  Nothing really
  concerning, and diffstat is a bit inflated due to some DT contents
  moving around on STi platforms.

  There's a collection of them here:

   - A fixup for a build breakage that hits on arm64 allmodconfig in
     QCOM SCM firmware drivers
   - MMC fixes for OMAP that had quite a bit of breakage this merge
     window.
   - Misc build/warning fixes on PXA and OMAP
   - A couple of minor fixes for Beagleboard X15 which is now starting
     to see a few more users in the wild"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
  ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
  ARM: dts: fix omap2+ address translation for pbias
  firmware: qcom: scm: Add function stubs for ARM64
  ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
  ARM: omap2plus_defconfig: enable GPIO_PCA953X
  ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
  ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
  ARM: dts: am57xx-beagle-x15: Update Phy supplies
  ARM: pxa: balloon3: Fix build error
  ARM: dts: Fixup model name for HP t410 dts
  ARM: dts: DRA7: fix a typo in ethernet
  ARM: omap2plus_defconfig: make PCF857x built-in
  ARM: dts: Use ti,pbias compatible string for pbias
  ARM: OMAP5: Cleanup options for SoC only build
  ARM: DRA7: Select missing options for SoC only build
  ARM: OMAP2+: board-generic: Remove stale of_irq macros
  ARM: OMAP4+: PM: erratum is used by OMAP5 and DRA7 as well
  ARM: dts: omap3-igep: Move eth IRQ pinmux to IGEPv2 common dtsi
  ARM: dts: am57xx-beagle-x15: Add wakeup irq for mcp79410
  ARM: dts: am335x-phycore-som: Fix mpu voltage
  ...

Pull CIFS fixes from Steve French:
 "Four fixes from testing at the recent SMB3 Plugfest including two
  important authentication ones (one fixes authentication problems to
  some popular servers when clock times differ more than two hours
  between systems, the other fixes Kerberos authentication for SMB3)"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  fix encryption error checks on mount
  [SMB3] Fix sec=krb5 on smb3 mounts
  cifs: use server timestamp for ntlmv2 authentication
  disabling oplocks/leases via module parm enable_oplocks broken for SMB3

ARM: pxa: fixes for v4.3

These fixes are mainly regression fixes triggered by irq changes,
common clock framework introduction and sound side-effect of
other platforms.

* tag 'pxa-fixes-v4.3' of https://github.com/rjarzmik/linux:
  ARM: pxa: balloon3: Fix build error
  ARM: pxa: ssp: Fix build error by removing originally incorrect DT binding
  ARM: pxa: fix DFI bus lockups on startup
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.3-rc cycle:

- Two more patches to fix most of the MMC regressions with the
  PBIAS regulator changes. At least two MMC driver related issues
  still seems to remain for omap3 legacy booting and omap4 duovero.
  Note that the dts changes depend on a recent regulator fix, and
  are based on the regulator commit now in mainline kernel

- Enable autoidle for am43xx clocks to prevent clocks from staying
  always on

- Fix i2c5 pinctrl offsets for omap5-uevm

- Enable PCA953X as that's needed for HDMI to work on omap5

- Update phy supplies for beagle x15 beta board

- Use palmas-usb for on beagle x15 to start using the related
  driver that recently got merged

* tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: fix omap2+ address translation for pbias
  ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
  ARM: omap2plus_defconfig: enable GPIO_PCA953X
  ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
  ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
  ARM: dts: am57xx-beagle-x15: Update Phy supplies
  regulator: pbias: program pbias register offset in pbias driver
  ARM: omap2plus_defconfig: Enable MUSB DMA support
  ARM: DRA752: Add ID detect for ES2.0
  ARM: OMAP3: vc: fix 'or' always true warning
  ARM: OMAP2+: Fix booting if no timer parent clock is available
  ARM: OMAP2+: omap-device: fix race deferred probe of omap_hsmmc vs omap_device_late_init
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - check the return value of platform_get_irq as signed int in xgene.

   - skip adf_dev_restore on virtual functions in qat.

   - fix double-free with backlogged requests in marvell_cesa"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  hwrng: xgene - fix handling platform_get_irq
  crypto: qat - VF should never trigger SBR on PH
  crypto: marvell - properly handle CRYPTO_TFM_REQ_MAY_BACKLOG-flagged requests

Pull SCSI target fixes from Nicholas Bellinger:
 "This includes a iser-target series from Jenny + Sagi @ Mellanox that
  addresses the few remaining active I/O shutdown bugs, along with a
  patch to support zero-copy for immediate data payloads that gives a
  nice performance improvement for small block WRITEs.

  Also included are some recent >= v4.2 regression bug-fixes.  The most
  notable is a RCU conversion regression for SPC-3 PR registrations, and
  recent removal of obsolete RFC-3720 markers that introduced a login
  regression bug with MSFT iSCSI initiators.

  Thanks to everyone who has been testing + reporting bugs for v4.x"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target: Avoid OFMarker + IFMarker negotiation
  target: Make TCM_WRITE_PROTECT failure honor D_SENSE bit
  target: Fix target_sense_desc_format NULL pointer dereference
  target: Propigate backend read-only to core_tpg_add_lun
  target: Fix PR registration + APTPL RCU conversion regression
  iser-target: Skip data copy if all the command data comes as immediate
  iser-target: Change the recv buffers posting logic
  iser-target: Fix pending connections handling in target stack shutdown sequnce
  iser-target: Remove np_ prefix from isert_np members
  iser-target: Remove unused variables
  iser-target: Put the reference on commands waiting for unsol data
  iser-target: remove command with state ISTATE_REMOVE

Pull USB fixes from Greg KH:
 "Here are some USB driver fixes for 4.3-rc3.

  There's the usual assortment of new device ids, combined with xhci and
  gadget driver fixes.  Full details in the shortlog.  All of these have
  been in linux-next with no reported problems"

* tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (34 commits)
  MAINTAINERS: remove amd5536udc USB gadget driver maintainer
  USB: whiteheat: fix potential null-deref at probe
  xhci: init command timeout timer earlier to avoid deleting it uninitialized
  xhci: change xhci 1.0 only restrictions to support xhci 1.1
  usb: xhci: exit early in xhci_setup_device() if we're halted or dying
  usb: xhci: stop everything on the first call to xhci_stop
  usb: xhci: Clear XHCI_STATE_DYING on start
  usb: xhci: lock mutex on xhci_stop
  xhci: Move xhci_pme_quirk() behind #ifdef CONFIG_PM
  xhci: give command abortion one more chance before killing xhci
  usb: Use the USB_SS_MULT() macro to get the burst multiplier.
  usb: dwc3: gadget: Fix BUG in RT config
  usb: musb: fix cppi channel teardown for isoch transfer
  usb: phy: isp1301: Export I2C module alias information
  usb: gadget: drop null test before destroy functions
  usb: gadget: dummy_hcd: in transfer(), return data sent, not limit
  usb: gadget: dummy_hcd: fix rescan logic for transfer
  usb: gadget: dummy_hcd: fix unneeded else-if condition
  usb: gadget: dummy_hcd: emulate sending zlp in packet logic
  usb: musb: dsps: fix polling in device-only mode
  ...

Pull serial driver fix from Greg KH:
 "Here is one serial driver fix for 4.3-rc3 that resolves a module
  loading issue due to splitting up of the 8250 driver into smaller
  pieces.  It's been in linux-next with no reported problems"

* tag 'tty-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: Add missing module license for 8250_base.ko

Pull staging driver fixes from Greg KH:
 "Here are some tiny staging driver and documentation fixes for 4.3-rc3.

  All of these resolve reported issues that people have found and have
  been in the linux-next tree for a while with no problems"

* tag 'staging-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  MAINTAINERS: Update email address for Martyn Welch
  staging: ion: fix corruption of ion_import_dma_buf
  staging: dgap: Remove myself from the MAINTAINERS file
  staging: most: Add dependency to HAS_IOMEM
  staging: unisys: remove reference of visorutil
  staging: unisys: visornic: handle error return from device registration
  staging: unisys: stop device registration before visorbus registration
  staging: unisys: visorbus: Unregister driver on error
  staging: unisys: visornic: Fix receive bytes statistics
  staging: unisys: unregister netdev when create debugfs fails
  staging: fbtft: replace master->setup() with spi_setup()
  staging: fbtft: fix 9-bit SPI support detection
  staging/lustre: change Lustre URLs and mailing list
  staging/android: Update ION TODO per LPC discussion
  Staging: most: MOST and MOSTCORE should depend on HAS_DMA
  staging: most: fix HDM_USB dependencies and build errors

Pull driver core fix from Greg KH:
 "Here is one driver core fix for 4.3-rc3 that resolves a reported oops"

* tag 'driver-core-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  cpu/cacheinfo: Fix teardown path

Pull char/misc driver fixes from Greg KH:
 "Here's some tiny char and misc driver fixes that resolve some reported
  errors for 4.3-rc3.

  All of these have been in linux-next with no problems for a while"

* tag 'char-misc-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  extcon: Fix attached value returned by is_extcon_changed
  Drivers: hv: vmbus: fix init_vp_index() for reloading hv_netvsc
  mei: fix debugfs files leak on error path
  thunderbolt: Allow loading of module on recent Apple MacBooks with thunderbolt 2 controller

Pull networking fixes from David Miller:

 1) When we run a tap on netlink sockets, we have to copy mmap'd SKBs
    instead of cloning them.  From Daniel Borkmann.

 2) When converting classical BPF into eBPF, fix the setting of the
    source reg to BPF_REG_X.  From Tycho Andersen.

 3) Fix igmpv3/mldv2 report parsing in the bridge multicast code, from
    Linus Lussing.

 4) Fix dst refcounting for ipv6 tunnels, from Martin KaFai Lau.

 5) Set NLM_F_REPLACE flag properly when replacing ipv6 routes, from
    Roopa Prabhu.

 6) Add some new cxgb4 PCI device IDs, from Hariprasad Shenai.

 7) Fix headroom tests and SKB leaks in ipv6 fragmentation code, from
    Florian Westphal.

 8) Check DMA mapping errors in bna driver, from Ivan Vecera.

 9) Several 8139cp bug fixes (dev_kfree_skb_any in interrupt context,
    misclearing of interrupt status in TX timeout handler, etc.) from
    David Woodhouse.

10) In tipc, reset SKB header pointer after skb_linearize(), from Erik
    Hugne.

11) Fix autobind races et al. in netlink code, from Herbert Xu with
    help from Tejun Heo and others.

12) Missing SET_NETDEV_DEV in sunvnet driver, from Sowmini Varadhan.

13) Fix various races in timewait timer and reqsk_queue_hadh_req, from
    Eric Dumazet.

14) Fix array overruns in mac80211, from Johannes Berg and Dan
    Carpenter.

15) Fix data race in rhashtable_rehash_one(), from Dmitriy Vyukov.

16) Fix race between poll_one_napi and napi_disable, from Neil Horman.

17) Fix byte order in geneve tunnel port config, from John W Linville.

18) Fix handling of ARP replies over lightweight tunnels, from Jiri
    Benc.

19) We can loop when fib rule dumps cross multiple SKBs, fix from Wilson
    Kok and Roopa Prabhu.

20) Several reference count handling bug fixes in the PHY/MDIO layer
    from Russel King.

21) Fix lockdep splat in ppp_dev_uninit(), from Guillaume Nault.

22) Fix crash in icmp_route_lookup(), from David Ahern.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
  net: Fix panic in icmp_route_lookup
  net: update docbook comment for __mdiobus_register()
  ppp: fix lockdep splat in ppp_dev_uninit()
  net: via/Kconfig: GENERIC_PCI_IOMAP required if PCI not selected
  phy: marvell: add link partner advertised modes
  net: fix net_device refcounting
  phy: add phy_device_remove()
  phy: fixed-phy: properly validate phy in fixed_phy_update_state()
  net: fix phy refcounting in a bunch of drivers
  of_mdio: fix MDIO phy device refcounting
  phy: add proper phy struct device refcounting
  phy: fix mdiobus module safety
  net: dsa: fix of_mdio_find_bus() device refcount leak
  phy: fix of_mdio_find_bus() device refcount leak
  ip6_tunnel: Reduce log level in ip6_tnl_err() to debug
  ip6_gre: Reduce log level in ip6gre_err() to debug
  fib_rules: fix fib rule dumps across multiple skbs
  bnx2x: byte swap rss_key to comply to Toeplitz specs
  net: revert "net_sched: move tp->root allocation into fw_init()"
  lwtunnel: remove source and destination UDP port config option
  ...

Andrey reported a panic:

[ 7249.865507] BUG: unable to handle kernel pointer dereference at 000000b4
[ 7249.865559] IP: [<c16afeca>] icmp_route_lookup+0xaa/0x320
[ 7249.865598] *pdpt = 0000000030f7f001 *pde = 0000000000000000
[ 7249.865637] Oops: 0000 [#1]
...
[ 7249.866811] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
4.3.0-999-generic #201509220155
[ 7249.866876] Hardware name: MSI MS-7250/MS-7250, BIOS 080014  08/02/2006
[ 7249.866916] task: c1a5ab00 ti: c1a52000 task.ti: c1a52000
[ 7249.866949] EIP: 0060:[<c16afeca>] EFLAGS: 00210246 CPU: 0
[ 7249.866981] EIP is at icmp_route_lookup+0xaa/0x320
[ 7249.867012] EAX: 00000000 EBX: f483ba48 ECX: 00000000 EDX: f2e18a00
[ 7249.867045] ESI: 000000c0 EDI: f483ba70 EBP: f483b9ec ESP: f483b974
[ 7249.867077]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 7249.867108] CR0: 8005003b CR2: 000000b4 CR3: 36ee07c0 CR4: 000006f0
[ 7249.867141] Stack:
[ 7249.867165]  320310ee 00000000 00000042 320310ee 00000000 c1aeca00
f3920240 f0c69180
[ 7249.867268]  f483ba04 f855058b a89b66cd f483ba44 f8962f4b 00000000
e659266c f483ba54
[ 7249.867361]  8004753c f483ba5c f8962f4b f2031140 000003c1 ffbd8fa0
c16b0e00 00000064
[ 7249.867448] Call Trace:
[ 7249.867494]  [<f855058b>] ? e1000_xmit_frame+0x87b/0xdc0 [e1000e]
[ 7249.867534]  [<f8962f4b>] ? tcp_in_window+0xeb/0xb10 [nf_conntrack]
[ 7249.867576]  [<f8962f4b>] ? tcp_in_window+0xeb/0xb10 [nf_conntrack]
[ 7249.867615]  [<c16b0e00>] ? icmp_send+0xa0/0x380
[ 7249.867648]  [<c16b102f>] icmp_send+0x2cf/0x380
[ 7249.867681]  [<f89c8126>] nf_send_unreach+0xa6/0xc0 [nf_reject_ipv4]
[ 7249.867714]  [<f89cd0da>] reject_tg+0x7a/0x9f [ipt_REJECT]
[ 7249.867746]  [<f88c29a7>] ipt_do_table+0x317/0x70c [ip_tables]
[ 7249.867780]  [<f895e0a6>] ? __nf_conntrack_find_get+0x166/0x3b0
[nf_conntrack]
[ 7249.867838]  [<f895eea8>] ? nf_conntrack_in+0x398/0x600 [nf_conntrack]
[ 7249.867889]  [<f84c0035>] iptable_filter_hook+0x35/0x80 [iptable_filter]
[ 7249.867933]  [<c16776a1>] nf_iterate+0x71/0x80
[ 7249.867970]  [<c1677715>] nf_hook_slow+0x65/0xc0
[ 7249.868002]  [<c1681811>] __ip_local_out_sk+0xc1/0xd0
[ 7249.868034]  [<c1680f30>] ? ip_forward_options+0x1a0/0x1a0
[ 7249.868066]  [<c1681836>] ip_local_out_sk+0x16/0x30
[ 7249.868097]  [<c1684054>] ip_send_skb+0x14/0x80
[ 7249.868129]  [<c16840f4>] ip_push_pending_frames+0x34/0x40
[ 7249.868163]  [<c16844a2>] ip_send_unicast_reply+0x282/0x310
[ 7249.868196]  [<c16a0863>] tcp_v4_send_reset+0x1b3/0x380
[ 7249.868227]  [<c16a1b63>] tcp_v4_rcv+0x323/0x990
[ 7249.868257]  [<c16776a1>] ? nf_iterate+0x71/0x80
[ 7249.868289]  [<c167dc2b>] ip_local_deliver_finish+0x8b/0x230
[ 7249.868322]  [<c167df4c>] ip_local_deliver+0x4c/0xa0
[ 7249.868353]  [<c167dba0>] ? ip_rcv_finish+0x390/0x390
[ 7249.868384]  [<c167d88c>] ip_rcv_finish+0x7c/0x390
[ 7249.868415]  [<c167e280>] ip_rcv+0x2e0/0x420
...

Prior to the VRF change the oif was not set in the flow struct, so the
VRF support should really have only added the vrf_master_ifindex lookup.

Fixes: 613d09b3 ("net: Use VRF device index for lookups on TX")
Cc: Andrey Melnikov <temnota.am@gmail.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the docbook comment for __mdiobus_register() to include the new
module owner argument.  This resolves a warning found by the 0-day
builder.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thomas can no longer work on the driver, so he asked me to mark the
MAINTAINER entry as "Orphan" with the hope that someone else would
someday pick it up.

Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull another cgroup fix from Tejun Heo:
 "The cgroup writeback support got inadvertently enabled for traditional
  hierarchies revealing two regressions which are currently being worked
  on.  It shouldn't have been enabled on traditional hierarchies, so
  disable it on them.  This is enough to make the regressions go away
  for people who aren't experimenting with cgroup"

* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup, writeback: don't enable cgroup writeback on traditional hierarchies

ppp_dev_uninit() locks all_ppp_mutex while under rtnl mutex protection.
ppp_create_interface() must then lock these mutexes in that same order
to avoid possible deadlock.

[  120.880011] ======================================================
[  120.880011] [ INFO: possible circular locking dependency detected ]
[  120.880011] 4.2.0 #1 Not tainted
[  120.880011] -------------------------------------------------------
[  120.880011] ppp-apitest/15827 is trying to acquire lock:
[  120.880011]  (&pn->all_ppp_mutex){+.+.+.}, at: [<ffffffffa0145f56>] ppp_dev_uninit+0x64/0xb0 [ppp_generic]
[  120.880011]
[  120.880011] but task is already holding lock:
[  120.880011]  (rtnl_mutex){+.+.+.}, at: [<ffffffff812e4255>] rtnl_lock+0x12/0x14
[  120.880011]
[  120.880011] which lock already depends on the new lock.
[  120.880011]
[  120.880011]
[  120.880011] the existing dependency chain (in reverse order) is:
[  120.880011]
[  120.880011] -> #1 (rtnl_mutex){+.+.+.}:
[  120.880011]        [<ffffffff81073a6f>] lock_acquire+0xcf/0x10e
[  120.880011]        [<ffffffff813ab18a>] mutex_lock_nested+0x56/0x341
[  120.880011]        [<ffffffff812e4255>] rtnl_lock+0x12/0x14
[  120.880011]        [<ffffffff812d9d94>] register_netdev+0x11/0x27
[  120.880011]        [<ffffffffa0147b17>] ppp_ioctl+0x289/0xc98 [ppp_generic]
[  120.880011]        [<ffffffff8113b367>] do_vfs_ioctl+0x4ea/0x532
[  120.880011]        [<ffffffff8113b3fd>] SyS_ioctl+0x4e/0x7d
[  120.880011]        [<ffffffff813ad7d7>] entry_SYSCALL_64_fastpath+0x12/0x6f
[  120.880011]
[  120.880011] -> #0 (&pn->all_ppp_mutex){+.+.+.}:
[  120.880011]        [<ffffffff8107334e>] __lock_acquire+0xb07/0xe76
[  120.880011]        [<ffffffff81073a6f>] lock_acquire+0xcf/0x10e
[  120.880011]        [<ffffffff813ab18a>] mutex_lock_nested+0x56/0x341
[  120.880011]        [<ffffffffa0145f56>] ppp_dev_uninit+0x64/0xb0 [ppp_generic]
[  120.880011]        [<ffffffff812d5263>] rollback_registered_many+0x19e/0x252
[  120.880011]        [<ffffffff812d5381>] rollback_registered+0x29/0x38
[  120.880011]        [<ffffffff812d53fa>] unregister_netdevice_queue+0x6a/0x77
[  120.880011]        [<ffffffffa0146a94>] ppp_release+0x42/0x79 [ppp_generic]
[  120.880011]        [<ffffffff8112d9f6>] __fput+0xec/0x192
[  120.880011]        [<ffffffff8112dacc>] ____fput+0x9/0xb
[  120.880011]        [<ffffffff8105447a>] task_work_run+0x66/0x80
[  120.880011]        [<ffffffff81001801>] prepare_exit_to_usermode+0x8c/0xa7
[  120.880011]        [<ffffffff81001900>] syscall_return_slowpath+0xe4/0x104
[  120.880011]        [<ffffffff813ad931>] int_ret_from_sys_call+0x25/0x9f
[  120.880011]
[  120.880011] other info that might help us debug this:
[  120.880011]
[  120.880011]  Possible unsafe locking scenario:
[  120.880011]
[  120.880011]        CPU0                    CPU1
[  120.880011]        ----                    ----
[  120.880011]   lock(rtnl_mutex);
[  120.880011]                                lock(&pn->all_ppp_mutex);
[  120.880011]                                lock(rtnl_mutex);
[  120.880011]   lock(&pn->all_ppp_mutex);
[  120.880011]
[  120.880011]  *** DEADLOCK ***

Fixes: 8cb775bc ("ppp: fix device unregistration upon netns deletion")
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

The builds of allmodconfig of avr32 is failing with:

drivers/net/ethernet/via/via-rhine.c:1098:2: error: implicit declaration
of function 'pci_iomap' [-Werror=implicit-function-declaration]
drivers/net/ethernet/via/via-rhine.c:1119:2: error: implicit declaration
of function 'pci_iounmap' [-Werror=implicit-function-declaration]

The generic empty pci_iomap and pci_iounmap is used only if CONFIG_PCI
is not defined and CONFIG_GENERIC_PCI_IOMAP is defined.

Add GENERIC_PCI_IOMAP in the dependency list for VIA_RHINE as we are
getting build failure when CONFIG_PCI and CONFIG_GENERIC_PCI_IOMAP both
are not defined.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Read the standard link partner advertisment registers and store it in
phydev->lp_advertising, so ethtool can report this information to
userspace via ethtool.  Zero it as per genphy if autonegotiation is
disabled.  Tested with a Marvell 88E1512 PHY.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull btrfs fixes from Chris Mason:
 "This is an assorted set I've been queuing up:

  Jeff Mahoney tracked down a tricky one where we ended up starting IO
  on the wrong mapping for special files in btrfs_evict_inode.  A few
  people reported this one on the list.

  Filipe found (and provided a test for) a difficult bug in reading
  compressed extents, and Josef fixed up some quota record keeping with
  snapshot deletion.  Chandan killed off an accounting bug during DIO
  that lead to WARN_ONs as we freed inodes"

* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: keep dropped roots in cache until transaction commit
  Btrfs: Direct I/O: Fix space accounting
  btrfs: skip waiting on ordered range for special files
  Btrfs: fix read corruption of compressed and shared extents
  Btrfs: remove unnecessary locking of cleaner_mutex to avoid deadlock
  Btrfs: don't initialize a space info as full to prevent ENOSPC

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Stable patches:
   - fix v4.2 SEEK on files over 2 gigs
   - Fix a layout segment reference leak when pNFS I/O falls back to inband I/O.
   - Fix recovery of recalled read delegations

  Bugfixes:
   - Fix a case where NFSv4 fails to send CLOSE after a server reboot
   - Fix sunrpc to wait for connections to complete before retrying
   - Fix sunrpc races between transport connect/disconnect and shutdown
   - Fix an infinite loop when layoutget fail with BAD_STATEID
   - nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
   - Fix a bogus WARN_ON_ONCE() in O_DIRECT when layout commit_through_mds is set
   - Fix layoutreturn/close ordering issues"

* tag 'nfs-for-4.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS41: make close wait for layoutreturn
  NFS: Skip checking ds_cinfo.buckets when lseg's commit_through_mds is set
  NFSv4.x/pnfs: Don't try to recover stateids twice in layoutget
  NFSv4: Recovery of recalled read delegations is broken
  NFS: Fix an infinite loop when layoutget fail with BAD_STATEID
  NFS: Do cleanup before resetting pageio read/write to mds
  SUNRPC: xs_sock_mark_closed() does not need to trigger socket autoclose
  SUNRPC: Lock the transport layer on shutdown
  nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
  SUNRPC: Ensure that we wait for connections to complete before retrying
  SUNRPC: drop null test before destroy functions
  nfs: fix v4.2 SEEK on files over 2 gigs
  SUNRPC: Fix races between socket connection and destroy code
  nfs: fix pg_test page count calculation
  Failing to send a CLOSE if file is opened WRONLY and server reboots on a 4.x mount