- 24 Apr, 2023 38 commits
-
-
Abhishek Pandit-Subedi authored
Add devcoredump APIs to hci core so that drivers only have to provide the dump skbs instead of managing the synchronization and timeouts. The devcoredump APIs should be used in the following manner: - hci_devcoredump_init is called to allocate the dump. - hci_devcoredump_append is called to append any skbs with dump data OR hci_devcoredump_append_pattern is called to insert a pattern. - hci_devcoredump_complete is called when all dump packets have been sent OR hci_devcoredump_abort is called to indicate an error and cancel an ongoing dump collection. The high level APIs just prepare some skbs with the appropriate data and queue it for the dump to process. Packets part of the crashdump can be intercepted in the driver in interrupt context and forwarded directly to the devcoredump APIs. Internally, there are 5 states for the dump: idle, active, complete, abort and timeout. A devcoredump will only be in active state after it has been initialized. Once active, it accepts data to be appended, patterns to be inserted (i.e. memset) and a completion event or an abort event to generate a devcoredump. The timeout is initialized at the same time the dump is initialized (defaulting to 10s) and will be cleared either when the timeout occurs or the dump is complete or aborted. Signed-off-by:
Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by:
Manish Mandlik <mmandlik@google.com> Reviewed-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
-
Chethan T N authored
Basically all Intel controllers support both Central/Peripheral LE states. This patch enables the LE States quirk by default on all Solar and Magnertor Intel controllers. Signed-off-by:
Chethan T N <chethan.tumkur.narayan@intel.com> Signed-off-by:
-
Steev Klimaszewski authored
Add regulators, GPIOs and changes required to power on/off wcn6855. Add support for firmware download for wcn6855 which is in the linux-firmware repository as hpbtfw21.tlv and hpnv21.bin. Based on the assumption that this is similar to the wcn6750 Tested-on: BTFW.HSP.2.1.0-00538-VER_PATCHZ-1 Signed-off-by:
Steev Klimaszewski <steev@kali.org> Reviewed-by:
Bjorn Andersson <andersson@kernel.org> Tested-by:
-
Steev Klimaszewski authored
Add bindings for the QTI WCN6855 chipset. Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Max Chou authored
The btrtl_set_quirks() has accessed btrtl_dev->ic_info->lmp_subver since b8e482d02513. However, if installing a Realtek Bluetooth controller without the driver supported, it will hit the NULL point accessed. Add a check for NULL to avoid the Kernel Oops. Signed-off-by:
Max Chou <max.chou@realtek.com> Signed-off-by:
-
Larry Finger authored
This device is part of a Realtek RTW8852BE chip. The device table is as follows: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3571 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Larry Finger authored
This device is part of a Realtek RTW8852BE chip. The device table entry is as follows: T: Bus=03 Lev=01 Prnt=01 Port=12 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=887b Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
-
Arnd Bergmann authored
The driver needs both CRC32 and CRC8 to link correctly: ld: drivers/bluetooth/btnxpuart.o: in function `nxp_serdev_probe': drivers/bluetooth/btnxpuart.c:1214: undefined reference to `crc8_populate_msb' ld: drivers/bluetooth/btnxpuart.o: in function `nxp_send_ack': drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8' ld: drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8' Fixes: 3e662aa4453a ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets") Signed-off-by:Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by:
-
Neeraj Sanjay Kale authored
This adds a driver based on serdev driver for the NXP BT serial protocol based on running H:4, which can enable the built-in Bluetooth device inside an NXP BT chip. This driver has Power Save feature that will put the chip into sleep state whenever there is no activity for 2000ms, and will be woken up when any activity is to be initiated over UART. This driver enables the power save feature by default by sending the vendor specific commands to the chip during setup. During setup, the driver checks if a FW is already running on the chip by waiting for the bootloader signature, and downloads device specific FW file into the chip over UART if bootloader signature is received.. Signed-off-by:
Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Reviewed-by:
-
Neeraj Sanjay Kale authored
Add binding document for NXP bluetooth chipsets attached over UART. Signed-off-by:
-
Neeraj Sanjay Kale authored
Adds serdev_device_break_ctl() and an implementation for ttyport. This function simply calls the break_ctl in tty layer, which can assert a break signal over UART-TX line, if the tty and the underlying platform and UART peripheral supports this operation. Signed-off-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Neeraj Sanjay Kale authored
This replaces all instances of ENOTSUPP with EOPNOTSUPP since ENOTSUPP is not a standard error code. This will help maintain consistency in error codes when new serdev API's are added. Signed-off-by:
-
Ilpo Järvinen authored
tty_set_termios() never returns anything else than 0. Make the debug prints to look directly into the new termios instead to check CRTSCTS state. Signed-off-by:
-
Raul Cheleguini authored
Add two more quirks to resume the device initialization and basic operation as the device seems not to support "Read Transmit Power" and "Set Extended Scan Parameters". < HCI Command: LE Read Transmit Power (0x08|0x004b) plen 0 > HCI Event: Command Status (0x0f) plen 4 LE Read Transmit Power (0x08|0x004b) ncmd 1 Status: Unknown HCI Command (0x01) < HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8 Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) PHYs: 0x01 Entry 0: LE 1M Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) > HCI Event: Command Status (0x0f) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Unknown HCI Command (0x01) Signed-off-by:Raul Cheleguini <rcheleguini@google.com> Signed-off-by:
-
Vasily Khoruzhick authored
The Realtek RTL8723CS is a SDIO WiFi chip. It also contains a Bluetooth module which is connected via UART to the host. It shares lmp subversion with 8703B, so Realtek's userspace initialization tool (rtk_hciattach) differentiates varieties of RTL8723CS (CG, VF, XX) with RTL8703B using vendor's command to read chip type. Also this chip declares support for some features it doesn't support so add a quirk to indicate that these features are broken. Signed-off-by:
Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by:
Bastian Germann <bage@debian.org> Signed-off-by:
-
Vasily Khoruzhick authored
Some adapters (e.g. RTL8723CS) advertise that they have more than 2 pages for local ext features, but they don't support any features declared in these pages. RTL8723CS reports max_page = 2 and declares support for sync train and secure connection, but it responds with either garbage or with error in status on corresponding commands. Signed-off-by:
-
Krzysztof Kozlowski authored
The driver can be compile tested with !CONFIG_OF making certain data unused: drivers/bluetooth/btmtkuart.c:971:36: error: ‘mt7668_data’ defined but not used [-Werror=unused-const-variable=] drivers/bluetooth/btmtkuart.c:966:36: error: ‘mt7663_data’ defined but not used [-Werror=unused-const-variable=] drivers/bluetooth/btmtkuart.c:962:36: error: ‘mt7622_data’ defined but not used [-Werror=unused-const-variable=] Signed-off-by:
-
Krzysztof Kozlowski authored
The driver can be compile tested with !CONFIG_OF making certain data unused: drivers/bluetooth/hci_qca.c:1869:37: error: ‘qca_soc_data_wcn6750’ defined but not used [-Werror=unused-const-variable=] drivers/bluetooth/hci_qca.c:1853:37: error: ‘qca_soc_data_wcn3998’ defined but not used [-Werror=unused-const-variable=] drivers/bluetooth/hci_qca.c:1841:37: error: ‘qca_soc_data_wcn3991’ defined but not used [-Werror=unused-const-variable=] drivers/bluetooth/hci_qca.c:1830:37: error: ‘qca_soc_data_wcn3990’ defined but not used [-Werror=unused-const-variable=] Signed-off-by:
-
Krzysztof Kozlowski authored
The driver can be compile tested with !CONFIG_OF making certain data unused: drivers/bluetooth/btmrvl_sdio.c:43:34: error: ‘btmrvl_sdio_of_match_table’ defined but not used [-Werror=unused-const-variable=] Signed-off-by:
-
Krzysztof Kozlowski authored
The driver can match only via the DT table so the table should be always used and the of_match_ptr does not have any sense (this also allows ACPI matching via PRP0001, even though it might not be relevant here). drivers/bluetooth/hci_ll.c:769:34: error: ‘hci_ti_of_match’ defined but not used [-Werror=unused-const-variable=] Signed-off-by:
-
Luiz Augusto von Dentz authored
This delays the identity address updates to give time for userspace to process the new address otherwise there is a risk that userspace creates a duplicated device if the MGMT event is delayed for some reason. Signed-off-by: -
Inga Stotland authored
This removes the following duplicate statement in hci_le_ext_directed_advertising_sync(): cp.own_addr_type = own_addr_type; Signed-off-by:
Inga Stotland <inga.stotland@intel.com> Signed-off-by:
-
Brian Gix authored
The msft_set_filter_enable() command was using the deprecated hci_request mechanism rather than hci_sync. This caused the warning error: hci0: HCI_REQ-0xfcf0 Signed-off-by:
Brian Gix <brian.gix@intel.com> Signed-off-by:
-
Archie Pusaka authored
Currently, when we initiate disconnection, we will wait for the peer's reply unless when we are suspending, where we fire and forget the disconnect request. A similar case is when adapter is powering off. However, we still wait for the peer's reply in this case. Therefore, if the peer is unresponsive, the command will time out and the power off sequence will fail, causing "bluetooth powered on by itself" to users. This patch makes the host doesn't wait for the peer's reply when the disconnection reason is powering off. Signed-off-by:
Archie Pusaka <apusaka@chromium.org> Reviewed-by:
Abhishek Pandit-Subedi <abhishekpandit@google.com> Reviewed-by:
-
Meng Tang authored
Tested on Acer Nitro AN515-47 Notebook output from /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0e4 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by:
Meng Tang <tangmeng@uniontech.com> Signed-off-by:
-
Chris Morgan authored
Update the compatible for the Realtek RTL8821CS bluetooth node. Signed-off-by:
Chris Morgan <macromorgan@hotmail.com> Signed-off-by:
-
Chris Morgan authored
RTL8821CS is a WiFi + Bluetooth combo chip from Realtek that provides WiFi A/B/G/N/AC over an SDIO interface and Bluetooth 4.2 over a UART interface. Note that the firmware this was tested with was firmware version 0x75b8f098. Signed-off-by:
-
Chris Morgan authored
Add compatible string for RTL8821CS for existing Realtek Bluetooth driver. Signed-off-by:
Alistair Francis <alistair@alistair23.me> Signed-off-by:
-
Meng Tang authored
This bluetooth device is found in a combo WLAN/BT card for a MediaTek 7663. Tested on Acer Aspire A315-24P Notebook The device information: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=3801 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by:
-
Luiz Augusto von Dentz authored
This fixes the following new warning: net/bluetooth/hci_sync.c:2403 hci_pause_addr_resolution() warn: missing error code? 'err' Reported-by:
kernel test robot <lkp@intel.com> Reported-by:
Dan Carpenter <error27@gmail.com> Link: https://lore.kernel.org/r/202302251952.xryXOegd-lkp@intel.com/Signed-off-by:
-
Luiz Augusto von Dentz authored
This makes hci_conn_hash_add append to the tail of the conn_hash so it matches the order they are created, this is required if the controller attempts to match the order of ACL with CIS which uses append logic when programming the CIS ids on the CIG. The result of this change affects Create CIS: Before: < HCI Command: LE Create Connected Isochronous Stream (0x08|0x0064) plen 9 Number of CIS: 2 CIS Handle: 2560 ACL Handle: 3586 CIS Handle: 2561 ACL Handle: 3585 After: < HCI Command: LE Create Connected Isochronous Stream (0x08|0x0064) plen 9 Number of CIS: 2 CIS Handle: 2560 ACL Handle: 3585 CIS Handle: 2561 ACL Handle: 3586 Signed-off-by: -
Victor Hassan authored
Add the support for RTL8852BS BT controller on UART interface. The necessary firmware file will be submitted to linux-firmware. Signed-off-by:
Victor Hassan <victor@allwinnertech.com> Signed-off-by:
-
Stefan Eichenberger authored
Add serdev support for the 88W8997 from NXP (previously Marvell). It includes support for changing the baud rate. The command to change the baud rate is taken from the user manual UM11483 Rev. 9 in section 7 (Bring-up of Bluetooth interfaces) from NXP. Signed-off-by:
Stefan Eichenberger <stefan.eichenberger@toradex.com> Signed-off-by:
Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by:
-
Stefan Eichenberger authored
Use the maybe_unused macro for the device tree ids instead of #ifdef CONFIG_OF. This makes it easier to add support for new devices. Signed-off-by:
-
Stefan Eichenberger authored
The 88W8997 bluetooth module supports setting the max-speed property. Signed-off-by:
-
Stefan Eichenberger authored
Update the documentation with the device tree binding for the Marvell 88W8997 bluetooth device. Signed-off-by:
-
Tomasz Moń authored
Remove hardcoded interface number check because Bluetooth specification since version 4.0 only recommends and no longer requires specific interface numbers. While earlier Bluetooth versions, i.e. 2.1 + EDR and 3.0 + HS, contain required configuration table in Volume 4 - Host Controller Interface Part B - USB Transport Layer, Bluetooth Core Specification Addendum 2 changes the table from required to recommended configuration. Signed-off-by:
Tomasz Moń <tomasz.mon@nordicsemi.no> Signed-off-by:
-
Luiz Augusto von Dentz authored
This makes use of BIT macro when defining bitfields which makes it clearer what bit it is toggling. Signed-off-by:
-
- 23 Apr, 2023 2 commits
-
-
David S. Miller authored
Pedro Tammela says: ==================== net/sched: act_pedit: minor improvements This series aims to improve the code and usability of act_pedit for netlink users. Patches 1-2 improves error reporting for extended keys parsing with extack. Patch 3 checks the static offsets a priori on create/update. Currently, this is done at the datapath for both static and runtime offsets. Patch 4 removes a check from the datapath which is redundant since the netlink parsing validates the key types. Patch 5 changes the 'pr_info()' calls in the datapath to rate limited versions. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Pedro Tammela authored
Unbounded info messages in the pedit datapath can flood the printk ring buffer quite easily depending on the action created. As these messages are informational, usually printing some, not all, is enough to bring attention to the real issue. Reviewed-by:
Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by:
Pedro Tammela <pctammela@mojatatu.com> Signed-off-by:
-
