Add support for running a msgqueue on the SEC2 falcon.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

On SEC, DMEM is unaccessible by the CPU when the falcon is running in LS
mode. This makes communication with the firmware using DMEM impossible.

For this purpose, a new kind of memory (EMEM) has been added. It works
similarly to DMEM, with the difference that its address space starts at
0x1000000. For this reason, it makes sense to treat it like a special
case of DMEM.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

All falcons have their FBIF registers starting at offset 0x600, with the
exception of the PMU and NVENC engines.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Not all falcons have a debug register, and it is not always found at the
same offset.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

SEC2 is the name given by NVIDIA to the SEC engine post-Fermi (reasons
unknown). Even though it shares the same address range as SEC, its usage
is quite different and this justifies a new engine. Add this engine and
make TOP use it all post-TOP devices should use this implementation and
not the older SEC.

Also quickly add the short gp102 implementation which will be used for
falcon booting purposes.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

gp10x' secure boot requires a blob to be run on NVDEC. Expose the falcon
through a dummy device.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Reading registers at device construction time can be harmful, as there
is no guarantee the underlying engine will be up, or in its runtime
configuration. Defer register reading to the oneinit() hook and update
users accordingly.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Both registers allow to bind a new context, but NXTCTX will work on all
falcons, while legacy NEW_INSTBLK is reserved to PMU.

After setting NXTCTX we trigger a context switch by writing 0x090 and
0x0a4.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Enable the PMU firmware in gm20b, managed by secure boot.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

gm20b PMU firmware is driven by a msgqueue, so connect relevant PMU
hooks to their msgqueue counterparts.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

The ACR firmware may return no error but fail nonetheless. Such cases
can be detected by verifying that the WPR region has been properly set
in FB. If this is not the case, this is an error, but the unload
firmware should still not be run.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

PMU support has been enabled for r352 ACR, but it must remain optional
if we want to preserve existing user-space that do not include it. Allow
ACR to be instanciated with a list of optional LS falcons, that will not
produce a fatal error if their firmware is not loaded. Also change the
secure boot bootstrap logic to be able to fall back to legacy behavior
if it turns out the boot falcon's LS firmware cannot be loaded.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Add the PMU bootloader generator and PMU LS ops that will enable proper
PMU operation if the PMU falcon is designated as managed.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Adapt secboot's behavior if a PMU firmware is present, in particular
the way LS falcons are reset. Without PMU firmware, secboot needs to be
performed again from scratch so all LS falcons are reset. With PMU
firmware, we can ask the PMU's ACR unit to reset a specific falcon
through a PMU message.

As we must preserve the old behavior to avoid breaking user-space, add a
few conditionals to the way falcons are reset.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Allow secboot to load a LS PMU firmware. LS PMU is one instance of
firmwares based on the message queue mechanism, which is also used for
other firmwares like SEC, so name its source file accordingly.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

NVIDIA-provided PMU firmware is controlled by a msgqueue. Add a member
to the PMU structure as well as the required cleanup code if this
feature is used.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Add support for the msgqueue firmware used to process PMU commands for
gm20b.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

A message queue firmware implements a specific protocol allowing the
host to send "commands" to a falcon, and the falcon to reply using
"messages". This patch implements the common part of this protocol and
defines the interface that the host can use.

Due to the way the firmware is developped internally at NVIDIA (where
kernel driver and firmware evolve in lockstep), firmwares taken at
different points in time can have frustratingly subtle differences that
must be taken into account. This code is architectured to make
implementing such differences as easy as possible.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Add the ability for LS firmwares to declare a post-run hook that is
invoked right after the HS firmware is executed. This allows them to
e.g. write some initialization data into the falcon's DMEM.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

As different firmare versions use different HS descriptor formats, we
need to abstract this part as well.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This structure does not need to be shared anymore.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This allows the bootloader descriptor generation code to not rely on
specialized ls_ucode_img structures, making it reusable in other
instances.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Offsets were not properly computed. This went unnoticed because we are
only using one app for now.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Using 32-bit integers would trim the WPR address if it is allocated above 4GB.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

A WPR region smaller than 256K will result in secure boot failure.
Adjust the minimal size.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

The WPR address parameter of the ls_write_wpr hook was defined as a u32,
which will very likely overflow on boards with more than 4GB VRAM.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Check at contruction time that we have support for all the LS firmwares
asked by the caller.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Remove a leftover that became obsolete with the falcon interface.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

All IMEM registers are duplicated per port.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

DMEM registers are replicated with a stride of 8 bytes.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

The falcon library may be used concurrently, especially after the
introduction of the msgqueue interface. Make it safe to use it that way.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This is not used currently, but is added for the sake of completeness.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Some PMU implementations (in particular the ones managed by secure
boot) may not have a reset() hook. Make sure we don't crash in that
case.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Make nvkm_secboot_falcon_name publicly visible as other subdevs will
need to use it for debug messages.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Ideally we'd be able to keep these at a more obvious error level, as
they're a good indication of us doing something wrong.

However, NVIDIA's FECS/GPCCS firmware touches registers that trigger
priv ring faults, and we can't do anything to fix that ourselves due
to the need for them to be signed by NVIDIA.

This issue was reported a while back, but hasn't been fixed, so, for
now we will hide the messages to prevent spamming Optimus users with
messages whenever the NVIDIA GPU is powered off and on again.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Merge tag 'drm-misc-next-fixes-2017-02-27' of git://anongit.freedesktop.org/git/drm-misc into drm-next

Misc fixes for the 4.11 merge window.

- vmwgfx drm_control node compat patch
- rockchip&zte fix
- compat32 support for dma-buf ioctl (cc: stable ofc, since this is a
  massive fumble. oops)

* tag 'drm-misc-next-fixes-2017-02-27' of git://anongit.freedesktop.org/git/drm-misc:
  dma-buf: add support for compat ioctl
  drm/vmwgfx: Work around drm removal of control nodes
  drm/rockchip: cdn-dp: Fix error handling
  drm/rockchip: add extcon dependency for DP
  drm: zte: fix static checker warning on variable 'fmt'

Pull another tracing update from Steven Rostedt:
 "Commit 79c6f448 ("tracing: Fix hwlat kthread migration") fixed a
  bug that was caused by a race condition in initializing the hwlat
  thread. When fixing this code, I realized that it should have been
  done differently. Instead of doing the rewrite and sending that to
  stable, I just sent the above commit to fix the bug that should be
  back ported.

  This commit is on top of the quick fix commit to rewrite the code the
  way it should have been written in the first place"

* tag 'trace-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Clean up the hwlat binding code

Pull tracing updates from Steven Rostedt:
 "This release has no new tracing features, just clean ups, minor fixes
  and small optimizations"

* tag 'trace-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (25 commits)
  tracing: Remove outdated ring buffer comment
  tracing/probes: Fix a warning message to show correct maximum length
  tracing: Fix return value check in trace_benchmark_reg()
  tracing: Use modern function declaration
  jump_label: Reduce the size of struct static_key
  tracing/probe: Show subsystem name in messages
  tracing/hwlat: Update old comment about migration
  timers: Make flags output in the timer_start tracepoint useful
  tracing: Have traceprobe_probes_write() not access userspace unnecessarily
  tracing: Have COMM event filter key be treated as a string
  ftrace: Have set_graph_function handle multiple functions in one write
  ftrace: Do not hold references of ftrace_graph_{notrace_}hash out of graph_lock
  tracing: Reset parser->buffer to allow multiple "puts"
  ftrace: Have set_graph_functions handle write with RDWR
  ftrace: Reset fgd->hash in ftrace_graph_write()
  ftrace: Replace (void *)1 with a meaningful macro name FTRACE_GRAPH_EMPTY
  ftrace: Create a slight optimization on searching the ftrace_hash
  tracing: Add ftrace_hash_key() helper function
  ftrace: Convert graph filter to use hash tables
  ftrace: Expose ftrace_hash_empty and ftrace_lookup_ip
  ...

Add compat ioctl support to dma-buf. This lets one to use DMA_BUF_IOCTL_SYNC
ioctl from 32bit application on 64bit kernel. Data structures for both 32
and 64bit modes are same, so there is no need for additional translation
layer.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1487683261-2655-1-git-send-email-m.szyprowski@samsung.com

vmware tools has a daemon that gets layout information from the GUI and
forwards it to DRM so that the modesetting code can set preferred connector
locations and modes. This daemon was using control nodes but since control
nodes were just removed, make it possible for the daemon to use render- or
primary nodes instead. This is a bit ugly but will allow drm to proceed with
removal of the mostly unused control-node code and allow vmware to proceed
with fixing up automatic layout settings for gnome-shell/wayland.

We bump minor to inform user-space about the api change.

Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170221104227.2854-1-thellstrom@vmware.com