- 12 May, 2020 28 commits
-
-
Benjamin Block authored
Common status flags that all main objects - adapter, port, and unit - support are propagated to sub-objects when set or cleared. For instance, when setting the status ZFCP_STATUS_COMMON_ERP_INUSE for an adapter object, we will propagate this to all its child ports and units - same for when clearing a common status flag. Units of an adapter object are enumerated via __shost_for_each_device() over the scsi host object of the corresponding adapter. Once we move the scsi host object allocation and registration to after the first exchange config and exchange port data, this won't be possible for cases where we set or clear common statuses during the very first adapter recovery. But since we won't have any port or unit objects yet at that point of time, we can just fence the status propagation for cases where the scsi host object is not yet set in the adapter object. It won't change any effective status propagations, but will prevent us from dereferencing invalid pointers. For any later point in the work flow the scsi host object will be set and thus nothing is changed then. Link: https://lore.kernel.org/r/f51fe5f236a1e3d1ce53379c308777561bfe35e1.1588956679.git.bblock@linux.ibm.comReviewed-by:
Steffen Maier <maier@linux.ibm.com> Signed-off-by:
Benjamin Block <bblock@linux.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Benjamin Block authored
When doing the very first adapter recovery - initialization - for a FCP device in a point-to-point topology we also allocate the port object corresponding to the attached remote port, and trigger a port recovery for it that will run after the adapter recovery finished. Right now this happens right after we finished with the exchange config data command, and uses the fibre channel host object corresponding to the FCP device to determine whether a point-to-point topology is used. When moving the scsi host object allocation and registration - and thus also the fibre channel host object allocation - to after the first exchange config and exchange port data, this use of the fc_host object is not possible anymore at that point in the work flow. But the allocation and recovery trigger doesn't have notable side-effects on the following exchange port data processing, so we can move those to after xport data, and thus also to after the scsi host object allocation, once we move it. Then the fc_host object can be used again, like it is now. For any further adapter recoveries this doesn't change anything, because at that point the port object already exists and recovery is triggered elsewhere for existing port objects. Link: https://lore.kernel.org/r/73e5d4ac21e2b37bf0c3ca8e530bc5a5c6e74f8f.1588956679.git.bblock@linux.ibm.comReviewed-by:
-
Benjamin Block authored
When receiving a notification that a FCP device lost its local link we usually update the fibre channel host object which represents that FCP device to reflect that. This notification/information can also surface when the FCP device is running through adapter recovery (exchange config and exchange port data return incomplete). When moving the scsi host object allocation and registration - and thus also the fibre channel host object allocation - to after the first exchange config and exchange port data, and this happens during the very first adapter recovery, these updates can not be done until after the scsi host object is allocated. Reorder the fc_host updates in zfcp_fsf_fc_host_link_down() so that they only happen after a check of whether the scsi host object is already allocated or not. During the first adapter recovery this will cause the skip of these updates if a link-down condition is detected, but we can repeat them after we allocated the scsi host object, if necessary. For any further link-down handling the only changes in the work flow are the slightly reordered assignments in zfcp_fsf_fc_host_link_down(). Link: https://lore.kernel.org/r/f841f2cda61dcd7b8549910c44e1831927459edf.1588956679.git.bblock@linux.ibm.comReviewed-by:
-
Benjamin Block authored
When executing exchange port data for a FCP device for the first time, or after an adapter recovery, we update several properties of the fibre channel host object which represents that FCP device. When moving the scsi host object allocation and registration - and thus also the fibre channel host object allocation - to after the first exchange config and exchange port data, this is not possible for the former case. Move all these update into separate, and fenced function that first checks whether the scsi host object already exists or not, before making the updates. During the first ever exchange port data in the adapter life cycle this will make the exchange port data handler skip over this update step, but we can repeat it later, after we allocated the scsi host object. For any further recovery of that adapter the work flow is only changed slightly because then the scsi host object already exists and we don't free it until we release the adapter completely at the end of its life cycle. Link: https://lore.kernel.org/r/ae454c2dc6da0b02907c489af91d0b211d331825.1588956679.git.bblock@linux.ibm.comReviewed-by:
-
Benjamin Block authored
When executing exchange config data for a FCP device for the first time, or after an adapter recovery, we update several properties of the scsi host or fibre channel host object that represent that FCP device. When moving the scsi host object allocation and registration - and thus also the fibre channel host object allocation - to after the first exchange config and exchange port data, this is not possible for the former case. Move all these update into separate, and fenced function that first checks whether the scsi host object already exists or not, before making the updates. During the first ever exchange config data in the adapter life cycle this will make the exchange config data handler skip over this update step, but we can repeat it later, after we allocated the scsi host object. For any further recovery of that adapter the work flow is only changed slightly because then the scsi host object already exists and we don't free it until we release the adapter completely at the end of its life cycle. Link: https://lore.kernel.org/r/5fc3f4d38d4334f7aa595497c6f7865fb1102e0f.1588956679.git.bblock@linux.ibm.comReviewed-by:
-
Benjamin Block authored
When establishing and activating the QDIO queue pair for a FCP device for the first time, or after an adapter recovery, we publish some of its characteristics to the scsi host object representing that FCP device. When moving the scsi host object allocation and registration to after the first exchange config and exchange port data, this is not possible for the former case - QDIO open for the first time - because that happens before exchange config and exchange port data. Move the scsi host object update into a fenced function that checks whether the object already exists or not. This way we can repeat that step later, once we are past the allocation. Once the first recovery succeeds we don't release the scsi host object anymore, so further recoveries do work as before. Link: https://lore.kernel.org/r/a214ebf508f71e3690113e3e90edab1cea0e24e3.1588956679.git.bblock@linux.ibm.comReviewed-by:
-
Samuel Zou authored
Fix the following versioncheck warning: drivers/scsi/mpt3sas/mpt3sas_debugfs.c:16:1: unused including <linux/version.h> Link: https://lore.kernel.org/r/1588938573-57847-1-git-send-email-zou_wei@huawei.comReported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Samuel Zou <zou_wei@huawei.com> Signed-off-by:
-
Suganath Prabu S authored
Fix following warning from Smatch static analyser: drivers/scsi/mpt3sas/mpt3sas_base.c:5256 _base_allocate_memory_pools() warn: 'ioc->hpr_lookup' double freed drivers/scsi/mpt3sas/mpt3sas_base.c:5256 _base_allocate_memory_pools() warn: 'ioc->internal_lookup' double freed Link: https://lore.kernel.org/r/20200508110738.30732-1-suganath-prabu.subramani@broadcom.comReported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by:
-
Chandrakanth Patil authored
Link: https://lore.kernel.org/r/20200508085314.23461-1-chandrakanth.patil@broadcom.comSigned-off-by:
Chandrakanth Patil <chandrakanth.patil@broadcom.com> Signed-off-by:
-
Sumit Saxena authored
When TM command times out, driver invokes the controller reset. Post reset, driver re-fires pended TM commands which leads to firmware crash. Post controller reset, return pended TM commands back to OS. Link: https://lore.kernel.org/r/20200508085242.23406-1-chandrakanth.patil@broadcom.com Cc: stable@vger.kernel.org Signed-off-by:
Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by:
-
Shivasharan S authored
MFI_BIG_ENDIAN macro used in drivers structure bitfield to check the CPU big endianness is undefined which would break the code on big endian machine. __BIG_ENDIAN_BITFIELD kernel macro should be used in places of MFI_BIG_ENDIAN macro. Link: https://lore.kernel.org/r/20200508085130.23339-1-chandrakanth.patil@broadcom.com Fixes: a7faf81d ("scsi: megaraid_sas: Set no_write_same only for Virtual Disk") Cc: <stable@vger.kernel.org> # v5.6+ Signed-off-by:
Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by:
-
Sumit Saxena authored
As blk_queue_virt_boundary() API in slave_configure ensures that no IOs will come with holes/gaps. Hence, code logic to detect the holes/gaps in IO buffer is not required. Link: https://lore.kernel.org/r/20200508083838.22778-3-chandrakanth.patil@broadcom.comSigned-off-by:
-
Kashyap Desai authored
The driver currently assigns a pre-defined queue depth when the firmware-provided device queue depth is greater than the controller queue depth. Use the controller queue depth if the reported target queue depth is too large. Link: https://lore.kernel.org/r/20200508083838.22778-2-chandrakanth.patil@broadcom.comSigned-off-by:
Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by:
-
Stanley Chu authored
Small cleanup as below items, 1. Use ufshcd_is_wb_allowed() directly instead of ufshcd_wb_sup() since ufshcd_wb_sup() just returns the result of ufshcd_is_wb_allowed(). 2. In ufshcd_suspend(), "else if (!ufshcd_is_runtime_pm(pm_op)) can be simplified to "else" since both have the same meaning. This patch does not change any functionality. Link: https://lore.kernel.org/r/20200508080115.24233-9-stanley.chu@mediatek.comReviewed-by:Avri Altman <avri.altman@wdc.com> Reviewed-by:
Asutosh Das <asutoshd@codeaurora.org> Signed-off-by:
Stanley Chu <stanley.chu@mediatek.com> Signed-off-by:
-
Stanley Chu authored
Enable WriteBooster capability on MediaTek UFS platforms. Link: https://lore.kernel.org/r/20200508080115.24233-8-stanley.chu@mediatek.comReviewed-by:
Bean Huo <beanhuo@micron.com> Reviewed-by:
-
Stanley Chu authored
According to UFS specification, there are two WriteBooster mode of operations: "LU dedicated buffer" mode and "shared buffer" mode. In the "LU dedicated buffer" mode, the WriteBooster Buffer is dedicated to a logical unit. If the device supports the "LU dedicated buffer" mode, this mode is configured by setting bWriteBoosterBufferType to 00h. The logical unit WriteBooster Buffer size is configured by setting the dLUNumWriteBoosterBufferAllocUnits field of the related Unit Descriptor. Only a value greater than zero enables the WriteBooster feature in the logical unit. Modify ufshcd_wb_probe() as above description to support LU Dedicated buffer mode. Note that according to UFS 3.1 specification, the valid value of bDeviceMaxWriteBoosterLUs parameter in Geometry Descriptor is 1, which means at most one LUN can have WriteBooster buffer in "LU dedicated buffer mode". Therefore this patch supports only one LUN with WriteBooster enabled. All WriteBooster related sysfs nodes are specifically mapped to the LUN with WriteBooster enabled in LU Dedicated buffer mode. Link: https://lore.kernel.org/r/20200508080115.24233-7-stanley.chu@mediatek.comReviewed-by:
-
Stanley Chu authored
For preparation of LU Dedicated buffer mode support on WriteBooster feature, "index" parameter shall be added and allowed to be specified by callers. Link: https://lore.kernel.org/r/20200508080115.24233-6-stanley.chu@mediatek.comReviewed-by:
Can Guo <cang@codeaurora.org> Reviewed-by:
-
Stanley Chu authored
Add fixup_dev_quirk vops in MediaTek UFS platforms and provide an initial vendor-specific device quirk table. Link: https://lore.kernel.org/r/20200508080115.24233-5-stanley.chu@mediatek.comReviewed-by:
-
Stanley Chu authored
Export ufs_fixup_device_setup() to allow vendors to re-use it for fixing device quriks on specified UFS hosts. Link: https://lore.kernel.org/r/20200508080115.24233-4-stanley.chu@mediatek.comReviewed-by:
-
Stanley Chu authored
Some UFS deivces may have required device quirks or have non-standard features which are enabled only on specified UFS hosts or for special customers. To not "pollute" common device quirk list, i.e. ufs_fixups table, for those devices mentioned above, introduce "fixup_dev_quirks" vops to allow vendors to fix or modify device quirks accordingly. Link: https://lore.kernel.org/r/20200508080115.24233-3-stanley.chu@mediatek.comReviewed-by:
-
Stanley Chu authored
The WriteBooster feature can be supported by some pre-3.1 UFS devices by upgrading firmware. To enable WriteBooster feature in such devices, introduce a device quirk to relax the entrance condition of ufshcd_wb_probe() to allow host driver to check those devices' WriteBooster capability. WriteBooster feature can be available if below all conditions are satisfied, 1. Host enables WriteBooster capability 2. UFS 3.1 device or UFS pre-3.1 device with quirk UFS_DEVICE_QUIRK_SUPPORT_EXTENDED_FEATURES enabled 3. The device descriptor shall have DEVICE_DESC_PARAM_EXT_UFS_FEATURE_SUP field 4. WriteBooster support is specified in above field Link: https://lore.kernel.org/r/20200508080115.24233-2-stanley.chu@mediatek.comReviewed-by: -
Colin Ian King authored
The variable rc is being initialized with a value that is never read and it is being updated later with a new value. The initialization is redundant and can be removed. Link: https://lore.kernel.org/r/20200507203111.64709-1-colin.king@canonical.comSigned-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Gustavo A. R. Silva authored
The current codebase makes use of the zero-length array language extension to the C90 standard, but the preferred mechanism to declare variable-length types such as these ones is a flexible array member[1][2], introduced in C99: struct foo { int stuff; struct boo array[]; }; By making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last in the structure, which will help us prevent some kind of undefined behavior bugs from being inadvertently introduced[3] to the codebase from now on. Also, notice that, dynamic memory allocations won't be affected by this change: "Flexible array members have incomplete type, and so the sizeof operator may not be applied. As a quirk of the original implementation of zero-length arrays, sizeof evaluates to zero."[1] sizeof(flexible-array-member) triggers a warning because flexible array members have incomplete type[1]. There are some instances of code in which the sizeof operator is being incorrectly/erroneously applied to zero-length arrays and the result is zero. Such instances may be hiding some bugs. So, this work (flexible-array member conversions) will also help to get completely rid of those sorts of issues. This issue was found with the help of Coccinelle. [1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html [2] https://github.com/KSPP/linux/issues/21 [3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour") Link: https://lore.kernel.org/r/20200507192550.GA16683@embeddedorSigned-off-by:Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by:
-
Gustavo A. R. Silva authored
The current codebase makes use of the zero-length array language extension to the C90 standard, but the preferred mechanism to declare variable-length types such as these ones is a flexible array member[1][2], introduced in C99: struct foo { int stuff; struct boo array[]; }; By making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last in the structure, which will help us prevent some kind of undefined behavior bugs from being inadvertently introduced[3] to the codebase from now on. Also, notice that, dynamic memory allocations won't be affected by this change: "Flexible array members have incomplete type, and so the sizeof operator may not be applied. As a quirk of the original implementation of zero-length arrays, sizeof evaluates to zero."[1] sizeof(flexible-array-member) triggers a warning because flexible array members have incomplete type[1]. There are some instances of code in which the sizeof operator is being incorrectly/erroneously applied to zero-length arrays and the result is zero. Such instances may be hiding some bugs. So, this work (flexible-array member conversions) will also help to get completely rid of those sorts of issues. This issue was found with the help of Coccinelle. [1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html [2] https://github.com/KSPP/linux/issues/21 [3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour") Link: https://lore.kernel.org/r/20200507192147.GA16206@embeddedorReviewed-by:John Garry <john.garry@huawei.com> Reviewed-by:
Jason Yan <yanaijie@huawei.com> Signed-off-by:
-
Xie XiuQi authored
uctrl and udev are unused after commit 9632a6b4 ("scsi: qedi: Move LL2 producer index processing in BH.") Remove them. Link: https://lore.kernel.org/r/20200505121904.25702-1-xiexiuqi@huawei.comReviewed-by:
Lee Duncan <lduncan@suse.com> Signed-off-by:
Xie XiuQi <xiexiuqi@huawei.com> Signed-off-by:
-
Jason Yan authored
Fix the following sparse warning: drivers/scsi/bfa/bfad_bsg.c:140:1: warning: symbol 'bfad_iocmd_ioc_get_stats' was not declared. Should it be static? Link: https://lore.kernel.org/r/20200505073807.40332-1-yanaijie@huawei.comReported-by:
-
Bodo Stroesser authored
We use tcm_loop with tape emulations running on tcmu. In case application reads a short tape block with a longer READ, or a long tape block with a short READ, according to SCC spec data has to be tranferred _and_ sensebytes with ILI set and information field containing the residual count. Similar problem also exists when using fixed block size in READ. Up to now tcm_loop is not prepared to handle sensebytes if input data is provided, as in tcm_loop_queue_data_in() it only sets SAM_STAT_GOOD and, if necessary, the residual count. To fix the bug, the same handling for sensebytes as present in tcm_loop_queue_status() must be done in tcm_loop_queue_data_in() also. After adding this handling, the two function now are nearly identical, so I created a single function with two wrappers. Link: https://lore.kernel.org/r/20200428182617.32726-1-bstroesser@ts.fujitsu.comSigned-off-by:
Bodo Stroesser <bstroesser@ts.fujitsu.com> Signed-off-by:
-
Zou Wei authored
Fix coccicheck warning which recommends to use memdup_user(). This patch fixes the following coccicheck warning: drivers/scsi/aacraid/commctrl.c:516:15-22: WARNING opportunity for memdup_user Link: https://lore.kernel.org/r/1587868964-75969-1-git-send-email-zou_wei@huawei.com Fixes: 4645df10 ("[PATCH] aacraid: swapped kmalloc args.") Reported-by:
-
- 08 May, 2020 12 commits
-
-
Dick Kennedy authored
Update lpfc version to 12.8.0.1 Link: https://lore.kernel.org/r/20200501214310.91713-10-jsmart2021@gmail.comReviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Signed-off-by:
-
Dick Kennedy authored
The MDS diagnostic enablement bit for the adapter interface is incorrect in the driver header. Correct the bit position for the SET_FEATURE MDS bit. Link: https://lore.kernel.org/r/20200501214310.91713-9-jsmart2021@gmail.comReviewed-by:
-
Dick Kennedy authored
Running make C=1 M=drivers/scsi/lpfc triggers sparse warnings Correct the code generating the following errors: - Incompatible address space assignment without proper conversion. - Deference of usespace and per-cpu pointers. Link: https://lore.kernel.org/r/20200501214310.91713-8-jsmart2021@gmail.comReviewed-by:
-
Dick Kennedy authored
In an audit of lockdep calls in the driver, there are multiple lockdep checks in successive calling layers. E.g. a routine checks, and then calls a lower routine that also checks, and so on. Calling sequences result in many redundant checks. Refine the code to remove lower-level lockdep checks. Update comments on the lock, correcting a few places where lock object in comment was incorrect. Link: https://lore.kernel.org/r/20200501214310.91713-7-jsmart2021@gmail.comReviewed-by:
-
Dick Kennedy authored
By default, the driver attempts to allocate a hdwq per logical cpu in order to provide good cpu affinity. Some systems have extremely high cpu counts and this can significantly raise memory consumption. In testing on x86 platforms (non-AMD) it is found that sharing of a hdwq by a physical cpu and its HT cpu can occur with little performance degredation. By sharing, the hdwq count can be halved, significantly reducing the memory overhead. Change the default behavior of the driver on non-AMD x86 platforms to share a hdwq by the cpu and its HT cpu. Link: https://lore.kernel.org/r/20200501214310.91713-6-jsmart2021@gmail.comReviewed-by:
-
Dick Kennedy authored
Implementation of a previous patch added a condition to an if check that always end up with the if test being true. Execution of the else clause was inadvertently negated. The additional condition check was incorrect and unnecessary after the other modifications had been done in that patch. Remove the check from the if series. Link: https://lore.kernel.org/r/20200501214310.91713-5-jsmart2021@gmail.com Fixes: b95b2119 ("scsi: lpfc: Fix loss of remote port after devloss due to lack of RPIs") Cc: <stable@vger.kernel.org> # v5.4+ Reviewed-by:
-
Dick Kennedy authored
The lldd rebinds the ndlp with rport during a nvme rport registration (via nvme_fc_register_remoteport). If rport & ndlp pointers are same as the previous one, the lldd will re-use the ndlp and rport association without re-initialization. This assumption is incorrect. The lldd should be ignorant of whether the returned rport pointer is new or not, and should always assume it is new. Remove the re-binding code, always assumes that rport pointer received from transport is a new pointer. Link: https://lore.kernel.org/r/20200501214310.91713-4-jsmart2021@gmail.comReviewed-by:
-
Dick Kennedy authored
A previous change introduced the atomic use of queue_claimed flag for eq's and cq's. The code works fine, but the clearing of the queue_claimed flag is not atomic. Change queue_claimed = 0 into xchg(&queue_claimed, 0) to be consistent for change under atomicity. Link: https://lore.kernel.org/r/20200501214310.91713-3-jsmart2021@gmail.comReviewed-by:
-
Bodo Stroesser authored
Currently in tcmu reservation commands are handled by core's pr implementation (default) or completely rejected (emulate_pr set to 0). We additionally want to be able to do full reservation handling in userspace. Therefore we need a way to set TRANSPORT_FLAG_PASSTHROUGH_PGR. The inverted flag is displayed by attribute pgr_support. Since we moved the flag from transport/backend to se_device in the previous commit, we now can make it changeable per device by allowing to write the attribute. The new field transport_flags_changeable in transport/backend is used to reject writing if not allowed for a backend. Regarding ALUA we also want to be able to passthrough commands to userspace in tcmu. Therefore we need TRANSPORT_FLAG_PASSTHROUGH_ALUA to be changeable, because by setting it we can switch off all ALUA checks in core. So we also set TRANSPORT_FLAG_PASSTHROUGH_ALUA in tcmu's transport_flags_changeable. Of course, ALUA and reservation handling in userspace will work only, if session/nexus information is sent to userspace along with every command. This will be object of a patch series announced by Mike Christie. Link: https://lore.kernel.org/r/20200427150823.15350-5-bstroesser@ts.fujitsu.comReviewed-by:
Mike Christie <mchristi@redhat.com> Signed-off-by:
-
Bodo Stroesser authored
pgr_support and alua_support device attributes show the inverted value of the transport_flags: * TRANSPORT_FLAG_PASSTHROUGH_PGR * TRANSPORT_FLAG_PASSTHROUGH_ALUA These attributes are per device, while the flags are per backend. Rename the transport_flags in backend/transport to transport_flags_default and use this value to initialize the new transport_flags field in the se_device structure. Now data and attribute both are per se_device. Link: https://lore.kernel.org/r/20200427150823.15350-4-bstroesser@ts.fujitsu.comReviewed-by:
-
Bodo Stroesser authored
tcmu has not set TRANSPORT_FLAG_PASSTHROUGH_PGR. Therefore the in-core pr emulation is active by default, but there are some attributes for configuration missing. Add them. Link: https://lore.kernel.org/r/20200427150823.15350-3-bstroesser@ts.fujitsu.comReviewed-by:
-
Bodo Stroesser authored
In commit b49d6f78 ("scsi: target: add emulate_pr backstore attr to toggle PR support") the new attribute emulate_pr was added. passthrough_parse_cdb() uses the attribute's value to distinguish whether reservation commands should be rejected or not. But the new attribute was not added to passthrough_attrib_attrs, so in pscsi and tcmu - the users of passthrough_parse_cdb() - the attribute is not available to change parser's behavior. Link: https://lore.kernel.org/r/20200427150823.15350-2-bstroesser@ts.fujitsu.comReviewed-by:
-
