The hardware supports the 332 8bpp and 4:4:4:4 16bpp formats,
but the table of supported formats didn't include them.
Add them in.

In theory they are supported for T-format as well as linear,
but without a way to test them just add them as linear for now.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-11-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

pixel_order is used for the earlier versions of the HVS, so is
redundant on the 10:10:10:2 and 10bit YUV formats that are only
supported on HVS5.
Remove the assignment from the table to avoid confusion.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-10-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

vc4_plane_mode_set for HVS5 was using pixel_order unless pixel_order_hvs5
was non-zero, except 0 is a valid value for the pixel_order.

Specify pixel_order_hvs5 for all formats and remove the conditional.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-9-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

atomic_flush will be called for each CRTC even if they aren't enabled.

The whole code we have there will thus run without a properly affected
channel, which can then result in all sorts of weird behaviour.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-8-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

HVS5 supports the 210101010 RGB[A|X] formats, but they were
missing from the DRM to HVS mapping list, so weren't available.
Add them in.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-7-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

Same as the xRGB8888 formats, HVS5 has managed to swap the colour
channels for the xRGB1555 formats as well. Add the relevant
config for pixel_order_hvs5.

Fixes: c54619b0 ("drm/vc4: Add support for the BCM2711 HVS5")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-6-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

Adds the zpos property to all planes, and creates the dlist
by placing the fragments in the correct order based on zpos.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-5-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

HVS5 has moved the interrupt enable bits around within the
DISPCTRL register, therefore the configuration has to be updated
to account for this.

Fixes: c54619b0 ("drm/vc4: Add support for the BCM2711 HVS5")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-4-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

The bit used for SCALER_DISPBKGND_AUTOHS in SCALER_DISPBKGNDX
has been repurposed on HVS5 to configure whether a display can
win back-to-back arbitration wins for the COB.

This is not desirable, therefore only select this bit on HVS4,
and explicitly clear it on HVS5.

Fixes: c54619b0 ("drm/vc4: Add support for the BCM2711 HVS5")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-3-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

The HVS can change AXI request mode based on how full the COB
FIFOs are.
Until now the vc4 driver has been relying on the firmware to
have set these to sensible values.

With HVS channel 2 now being used for live video, change the
panic mode for all channels to be explicitly set by the driver,
and the same for all channels.

Fixes: c54619b0 ("drm/vc4: Add support for the BCM2711 HVS5")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-2-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

The HVS Composite Output Buffer (COB) is the memory used to
generate the output pixel data.
Until now the vc4 driver has been relying on the firmware to
have set these to sensible values.

In testing triple screen support it has been noted that only
1 line was being assigned to HVS channel 2. Whilst that is fine
for the transposer (TXP), and indeed needed as only some pixels
have an alpha channel, it is insufficient to run a live display.

Split the COB more evenly between the 3 HVS channels.

Fixes: c54619b0 ("drm/vc4: Add support for the BCM2711 HVS5")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-1-1f8e0770798b@cerno.techSigned-off-by: Maxime Ripard <maxime@cerno.tech>

Many panel drivers define dsi_dcs_write_seq() and dsi_generic_write_seq()
macros to send DCS commands and generic write packets respectively, with
the payload specified as a list of parameters instead of using arrays.

There's already a macro for the former, introduced by commit 2a9e9daf
("drm/mipi-dsi: Introduce mipi_dsi_dcs_write_seq macro") so drivers can be
changed to use that. But there isn't one yet for the latter, let's add it.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102202542.3494677-2-javierm@redhat.com

Change made using a `clang-format -i include/drm/drm_mipi_dsi.h` command.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102202542.3494677-1-javierm@redhat.com

Replace the use of drm_debugfs_create_files() with the new
drm_debugfs_add_files() function, which center the debugfs files
management on the drm_device instead of drm_minor. Moreover, remove the
debugfs_init hook and add the debugfs files directly on hdlcd_drm_bind(),
before drm_dev_register().
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20221226155029.244355-4-mcanal@igalia.com

Replace the use of drm_debugfs_create_files() with the new
drm_debugfs_add_file() function, which center the debugfs files
management on the drm_device instead of drm_minor. Moreover, remove the
debugfs_init hook and add the debugfs files directly on gud_probe(),
before drm_dev_register().
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20221226155029.244355-3-mcanal@igalia.com

Replace the combination of bpp and depth with a single color-mode
argument. Handle special cases in simpledrm and ofdrm. Hard-code
XRGB8888 as fallback format for cases where no given format works.

The color-mode argument accepts the same values as the kernel's video
parameter. These are mostly bpp values between 1 and 32. The exceptions
are 15, which has a color depth of 15 and a bpp value of 16; and 32,
which has a color depth of 24 and a bpp value of 32.

v4:
	* add back lost test for bpp_specified (Maira)
	* add Fixes tag (Daniel)
v3:
	* fix ofdrm build (Maxime)
v2:
	* minimize changes (Daniel)
	* use drm_driver_legacy_fb_format() (Daniel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Maíra Canal <mcanal@igalia.com> # vc4 and vkms
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 37c90d58 ("drm/fb-helper: Fix single-probe color-format selection")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230106112324.22055-1-tzimmermann@suse.de

Now as all drivers stopped calling drm_bridge_connector_enable_hpd() and
drm_bridge_connector_disable_hpd() it is safe to remove them complelely.
Rename our internal helpers to remove the underscore prefix.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102180705.459294-8-dmitry.baryshkov@linaro.org

The functionality of drm_bridge_connector_enable_hpd() and
drm_bridge_connector_disable_hpd() is provided automatically by the
drm_kms_poll helpers. Stop calling these functions manually.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102180705.459294-7-dmitry.baryshkov@linaro.org

The functionality of drm_bridge_connector_enable_hpd() and
drm_bridge_connector_disable_hpd() is provided automatically by the
drm_kms_poll helpers. Stop calling these functions manually.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102180705.459294-6-dmitry.baryshkov@linaro.org

The functionality of drm_bridge_connector_enable_hpd() and
drm_bridge_connector_disable_hpd() is provided automatically by the
drm_kms_poll helpers. Stop calling these functions manually.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
[narmstrong: removed now unused kms var in dcss_dev_suspend|resume()]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102180705.459294-5-dmitry.baryshkov@linaro.org

Use drm_connector's helpers enable_hpd and disable_hpd to enable and
disable HPD automatically by the means of drm_kms_helper_poll_*
functions. As the drm_bridge_connector_enable_hpd() and
drm_bridge_connector_disable_hpd() functions are now unused, replace
them with stubs to ease driver migration.

Enabling the HPD from drm_bridge_connector_init() can happen too early,
before the driver is prepared to handle HPD events. As the
drm_bridge_connector_enable_hpd() is empty anyway, drop this call
anyway.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102180705.459294-4-dmitry.baryshkov@linaro.org

Introduce two drm_connector_helper_funcs: enable_hpd() and disable_hpd().
They are called by drm_kms_helper_poll_enable() and
drm_kms_helper_poll_disable() (and thus drm_kms_helper_poll_init() and
drm_kms_helper_poll_fini()) respectively.

This allows DRM drivers to rely on drm_kms_helper_poll for enabling and
disabling HPD detection rather than doing that manually.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102180705.459294-3-dmitry.baryshkov@linaro.org

Merge drm_kms_helper_poll_disable() and drm_kms_helper_poll_fini() code
into a common helper function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102180705.459294-2-dmitry.baryshkov@linaro.org

It's a bit a FAQ, and we really can't claim to be the authoritative
source for allocating these numbers used in many standard extensions
if we tell closed source or vendor stacks in general to go away.

Iirc this was already clarified in some vulkan discussions, but I
can't find that anywhere anymore. At least not in a public link.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Daniel Stone <daniel@fooishbar.org>
Cc: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Neil Trevett <ntrevett@nvidia.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: David Airlie <airlied@gmail.com>
Acked-by: Marek Olšák <maraeo@gmail.com>
Acked-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Acked-by: Jason Ekstrand <jason.ekstrand@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221123192437.1065826-1-daniel.vetter@ffwll.ch

Commit 5ea6b170 ("drm/panel: Add prepare_prev_first flag to
drm_panel") introduced an access to the bridge pointer in the
devm_drm_panel_bridge_add_typed() function.

However, due to the unusual ERR_PTR check when getting that pointer, the
pointer access is done even though the pointer might be an error
pointer.

Rework the function for a more traditional design that will return
immediately if it gets an ERR_PTR so that we never access the pointer in
that case.

Fixes: 5ea6b170 ("drm/panel: Add prepare_prev_first flag to drm_panel")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102120123.19062-1-maxime@cerno.tech
Link: https://patchwork.freedesktop.org/patch/msgid/20230102120123.19062-1-maxime@cerno.tech

Add a paragraph explaining that the default behavior for areas which
are not covered by planes or where planes are blending with the CRTC
background, is black.

This is alluded to in the "pixel blend mode" property docs, but not
called out explicitly.
Reviewed-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230103152738.1213785-1-sean@poorly.run

As v3d_submit_tfu_ioctl() performs the same steps as
drm_gem_object_lookup(), replace the open-code implementation in v3d
with its DRM core equivalent.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221227200010.191351-1-mcanal@igalia.com

Replace the deprecated macro with the per-device one.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20221223112302.320097-1-tvrtko.ursulin@linux.intel.com

Drivers only emulate XRGB8888 framebuffers. Remove all conversion
helpers that do not use XRGB8888 as their source format. Also remove
some special cases for alpha formats in the blit helper.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-14-tzimmermann@suse.de

The DRM helper drm_fb_build_fourcc_list() creates a list of color
formats for primary planes of the generic drivers. Simplify the helper:

 - It used to mix and filter native and emulated formats as provided
   by the driver. Now the only emulated format is XRGB8888, which is
   required as fallback by legacy software. Drop support for emulating
   any other formats.
 - Also convert alpha formats to their non-alpha counterparts. Generic
   drivers don't support primary planes with alpha formats and some
   DTs incorrectly advertise alpha channels for non-alpha hardware. So
   only export non-alpha formats for primary planes.

With the simplified helper, scrap format lists of the affected generic
drivers. All they need is the firmware buffer's native format, from which
the helper creates the list of color formats.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-13-tzimmermann@suse.de

Fix the color-format selection of the single-probe helper. Go
through all user-specified values and test each for compatibility
with the driver. If none is supported, use the driver-provided
default. This guarantees that the console is always available in
any color format at least.

Until now, the format selection of the single-probe helper tried
to either use a user-specified format or a 32-bit default format.
If the user-specified format was not supported by the driver, the
selection failed and the display remained blank.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-12-tzimmermann@suse.de

Split the single-probe helper's implementation into multiple
functions and get locking and overallocation out of the way of
the surface setup. Simplifies later changes to the setup code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-11-tzimmermann@suse.de

Add conversion from XRGB8888 to XRGB1555, ARGB1555 and RGBA5551, which
are the formats currently supported by the simplefb infrastructure. The
new helpers allow the output of XRGB8888 framebuffers to firmware
scanout buffers in one of the 15-bit formats.

v3:
	* use __le* for destination buffers (Jose, kernel test robot)
v2:
	* test 15-bit results with local endianness (Jose)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-10-tzimmermann@suse.de

Add dedicated helper to convert from XRGB8888 to ARGB2101010. Sets
all alpha bits to make pixels fully opaque.

v2:
	* set correct format in struct drm_framebuffer (Javier)
	* use cpubuf_to_le32()
	* type fixes
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-9-tzimmermann@suse.de

Add dedicated helper to convert from XRGB8888 to ARGB8888. Sets
all alpha bits to make pixels fully opaque.

v3:
	* use __le32 for destination buffer (Jose, kernel test robot)
v2:
	* use cpubuf_to_le32()
	* type fixes
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-8-tzimmermann@suse.de

Upcoming changes to the format conversion will mostly blit from
XRGB8888 to some other format. So put the source format in blit's
outer branches to make the code more readable. For cases where
a format only changes its endianness, such as XRGB565, introduce
dedicated branches that handle this for all formats.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-7-tzimmermann@suse.de

Change the source-buffer type of le32buf_to_cpu() to __le32* to
reflect endianness. Result buffers are converted to local endianness,
so instantiate them from regular u8 or u32 types.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-6-tzimmermann@suse.de

Fix to-RGB565 conversion helpers to store the result in little-
endian byte order. Update test cases as well.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-5-tzimmermann@suse.de

Convert test input for format helpers from host byte order to
little-endian order. The current code does it the other way around,
but there's no effective difference to the result.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-4-tzimmermann@suse.de

RGB888 is different than the other formats as most of its pixels are
unaligned and therefore helper functions do not use endianness conversion
helpers. Comment on this in the source code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102112927.26565-3-tzimmermann@suse.de