These are predefined states of the driver model. When not present,
as if not set in the device tree, they become no-ops.
Explicitly selecting the default state is not needed since the
device core layer sets pin mux to "default" state before probe.
This is not the simplest implementation, on AM335x at least, we could
switch to idle at any point in the suspend hook, only the default state
needs to be set before writing to the irq registers or an IRQ might get
lost.
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On multicores, an sdio irq handler could be running in parallel to
runtime suspend. In the worst case it could be waiting for the spinlock
held by the runtime suspend. When runtime suspend is complete and the
functional clock (fclk) turned off, the irq handler will continue and
cause a SIGBUS on the first register access.
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

To detect sdio irqs properly without spurious events,
OMAP4 needs IWE in CON and CTPL, CLKEXTFREE in HCTL to be set
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add SDIO IRQ entries to debugfs entry. Note that PSTATE shows current
state of data lines, incl. SDIO IRQ pending
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There have been various patches floating around for enabling
the SDIO IRQ for hsmmc, but none of them ever got merged.

Probably the reason for not merging the SDIO interrupt patches
has been the lack of wake-up path for SDIO on some omaps that
has also needed remuxing the SDIO DAT1 line to a GPIO making
the patches complex.

This patch adds the minimal SDIO IRQ support to hsmmc for
omaps that do have the wake-up path. For those omaps, the
DAT1 line need to have the wake-up enable bit set, and the
wake-up interrupt is the same as for the MMC controller.

This patch has been tested on am3730 es1.2 with mwifiex
connected to MMC3 with mwifiex waking to Ethernet traffic
from off-idle mode. Note that for omaps that do not have
the SDIO wake-up path, this patch will not work for idle
modes and further patches for remuxing DAT1 to GPIO are
needed.

Based on earlier patches [1][2] by David Vrabel
<david.vrabel@csr.com>, Steve Sakoman <steve@sakoman.com>

For now, only support SDIO interrupt if we are booted with
a separate wake-irq configued via device tree. This is
because omaps need the wake-irq for idle states, and some
omaps need special quirks. And we don't want to add new
legacy mux platform init code callbacks any longer as we
are moving to DT based booting anyways.

To use it, you need to specify the wake-irq using the
interrupts-extended property.

[1] http://www.sakoman.com/cgi-bin/gitweb.cgi?p=linux.git;a=commitdiff_plain;h=010810d22f6f49ac03da4ba384969432e0320453
[2] http://comments.gmane.org/gmane.linux.kernel.mmc/20446Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There is no need for an output like this:
> mmcblk mmc1:0001: calling add_quirk_mmc+0x0/0x20
Instead use this one:
> mmcblk mmc1:0001: calling add_quirk_mmc
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Remove the error path items that are no longer needed. The mmc card-detect
code cleans up after itself (and registers with devm) and the host error
is the same as the clock disable.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The pm_runtime call should implicitly disable the device once the
probe is over if there is no explicit reference gained. There is no
need to call pm_runtime_suspend() before the pm_runtime_disable()
call.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_request_threaded_irq() for the host interrupt handlers so we
do not have to worry about freeing them on exit or error. Tidies up the
exit path code for the driver.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use the devm_clk_get() code to get the clock and allow it to be freed
automatically on release.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Start tidying the probe/release code by using devm_ioremap_resource() to
map the IO registers.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Change the initial print to show chip version and the bus rate it is
working at instead of the driver version. This is more useful information
as we already know which driver version from the kernel it is in.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Remove those unused ret variables to make it obvious that these function
will not return any errors in the current implementation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Switch the common SDHCI code over to use mmc_host's regulator pointers
and remove the ones in the sdhci_host structure.  Additionally, use the
common mmc_regulator_get_supply function to get the regulators and set
the ocr_avail mask.

This change sets the ocr_avail directly based upon the voltage ranges
supported which ensures ocr_avail is set correctly while allowing the
use of regulators that can't provide exactly 1.8v, 3.0v, or 3.3v.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The runtime PM core handles a runtime_idle callback set to NULL as one
returning 0. So, let's just set it to NULL instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>

This patch adds a fake Qualcomm ID 0x00051180 to the amba_ids, as Qualcomm
SDCC controller is pl180, but amba id registers read 0x0's.
The plan is to remove SDCC driver totally and use mmci as the main SD
controller driver for Qualcomm SOCs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

MCIFIFOCNT register behaviour on Qcom chips is very different than the other
pl180 integrations. MCIFIFOCNT register contains the number of
words that are still waiting to be transferred through the FIFO. It keeps
decrementing once the host CPU reads the MCIFIFO. With the existing logic and
the MCIFIFOCNT behaviour, mmci_pio_read will loop forever, as the FIFOCNT
register will always return transfer size before reading the FIFO.

Also the data sheet states that "This register is only useful for debug
purposes and should not be used for normal operation since it does not reflect
data which may or may not be in the pipeline".

This patch implements a qcom specific get_rx_fifocnt function which is
implemented based on status register flags. Based on qcom_fifo flag in
variant data structure, the corresponding get_rx_fifocnt function is selected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On Controllers like Qcom SD card controller where cclk is mclk and mclk should
be directly controlled by the driver.

This patch adds support to control mclk directly in the driver, and also
adds explicit_mclk_control flag in variant structure giving more flexibility
to the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Fixed checkpatch warning
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Some of the controller have maximum supported frequency, This patch adds
support in variant data structure to specify such restrictions. This
gives more flexibility in calculating the f_max before passing it to
mmc-core.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On some SOCs like Qcom there are explicit bits in the command register
to specify if its a data transfer command or not. So this patch adds
support to such bits in variant data, giving more flexibility to the
driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds edge support for data and command out to variant structure
giving more flexibility to the driver to support more SOCs which have
different clock register layout.

Without this patch other new SOCs like Qcom will have to add more code to
special case them
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds 8bit bus enable to variant structure giving more flexibility
to the driver to support more SOCs which have different clock register layout.

Without this patch other new SOCs like Qcom will have to add more code
to special case them.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds ddrmode mask to variant structure giving more flexibility
to the driver to support more SOCs which have different datactrl register
layout.

Without this patch datactrl register is updated with incorrect ddrmode mask,
resulting in failures on Qualcomm SD Card Controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Instance of this IP on Qualcomm's SOCs has bit different layout for datactrl
register. Bit position datactrl[16:4] hold the true block size instead of power
of 2.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On Qcom SD Card controller POWER, CLKCTRL, DATACTRL and COMMAND registers
should be updated in MCLK domain, and writes to these registers must be
separated by three MCLK cycles. This resitriction is not applicable for
other registers. Any subsequent writes to these register will be ignored
until 3 MCLK have passed.

One usec delay between two CMD register writes is not sufficient in the
card identification phase where the CCLK is very low. This patch replaces
a static 1 usec delay to use mmci_reg_delay function which can provide
correct delay depending on the cclk frequency.

Without this patch the card is not detected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds a Qualcomm SD Card controller specific register variations
to header file. Qualcomm SDCC controller is pl180, with slight changes in
the register layout from standard pl180 register set.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch replaces a constant used in calculating timeout with a proper
macro. This is make code more readable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull devicetree bugfix from Grant Likely:
 "Important bug fix for parsing 64-bit addresses on 32-bit platforms.
  Without this patch the kernel will try to use memory ranges that
  cannot be reached"

* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
  of: Check for phys_addr_t overflows in early_init_dt_add_memory_arch

Pull SCSI fixes from James Bottomley:
 "This is a set of 13 fixes, a MAINTAINERS update and a sparse update.
  The fixes are mostly correct value initialisations, avoiding NULL
  derefs and some uninitialised pointer avoidance.

  All the patches have been incubated in -next for a few days.  The
  final patch (use the scsi data buffer length to extract transfer size)
  has been rebased to add a cc to stable, but only the commit message
  has changed"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] use the scsi data buffer length to extract transfer size
  virtio-scsi: fix various bad behavior on aborted requests
  virtio-scsi: avoid cancelling uninitialized work items
  ibmvscsi: Add memory barriers for send / receive
  ibmvscsi: Abort init sequence during error recovery
  qla2xxx: Fix sparse warning in qla_target.c.
  bnx2fc: Improve stats update mechanism
  bnx2fc: do not scan uninitialized lists in case of error.
  fc: ensure scan_work isn't active when freeing fc_rport
  pm8001: Fix potential null pointer dereference and memory leak.
  MAINTAINERS: Update LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) maintainers Email IDs
  be2iscsi: remove potential junk pointer free
  be2iscsi: add an missing goto in error path
  scsi_error: set DID_TIME_OUT correctly
  scsi_error: fix invalid setting of host byte

Pull drm fixes from Dave Airlie:
 "i915, tda998x and vmwgfx fixes,

  The main one is i915 fix for missing VGA connectors, along with some
  fixes for the tda998x from Russell fixing some modesetting problems.

  (still on holidays, but got a spare moment to find these)"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/vmwgfx: Fix incorrect write to read-only register v2:
  drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
  drm/i915: only apply crt_present check on VLV
  drm/i915: Wait for vblank after enabling the primary plane on BDW
  drm/i2c: tda998x: add some basic mode validation
  drm/i2c: tda998x: faster polling for edid
  drm/i2c: tda998x: move drm_i2c_encoder_destroy call

Pull ARM SoC fixes from Olof Johansson:
 "This week's arm-soc fixes:

   - A set of of OMAP patches that we had missed Tony's pull request of:
     * Reset fix for am43xx
     * Proper OPP table for omap5
     * Fix for SoC detection of one of the DRA7 SoCs
     * hwmod updates to get SATA and OCP to work on omap5 (drivers
       merged in 3.16)
     * ... plus a handful of smaller fixes
   - sunxi needed to re-add machine specific restart code that was
     removed in anticipation of a watchdog driver being merged for 3.16,
     and it didn't make it in.
   - Marvell fixes for PCIe on SMP and a big-endian fix.
   - A trivial defconfig update to make my capri test board boot with
     bcm_defconfig again.

  ... and a couple of MAINTAINERS updates, one to claim new Keystone
  drivers that have been merged, and one to merge MXS and i.MX (both
  Freescale platforms).

  The largest diffs come from the hwmod code for omap5 and the re-add of
  the restart code on sunxi.  The hwmod stuff is quite late at this
  point but it slipped through cracks repeatedly while coming up the
  maintainer chain and only affects the one SoC so risk is low"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: Add few more Keystone drivers
  MAINTAINERS: merge MXS entry into IMX one
  ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
  ARM: mvebu: fix cpuidle implementation to work on big-endian systems
  ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
  ARM: mvebu: move Armada 375 external abort logic as a quirk
  ARM: bcm: Fix bcm and multi_v7 defconfigs
  ARM: dts: dra7-evm: remove interrupt binding
  ARM: OMAP2+: Fix parser-bug in platform muxing code
  ARM: DTS: dra7/dra7xx-clocks: ATL related changes
  ARM: OMAP2+: drop unused function
  ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
  ARM: dts: omap5: Update CPU OPP table as per final production Manual
  ARM: DRA722: add detection of SoC information
  ARM: dts: Enable twl4030 off-idle configuration for selected omaps
  ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
  ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX

Pull irq fixes from Thomas Gleixner:
 "A few minor fixlets in ARM SoC irq drivers and a fix for a memory leak
  which I introduced in the last round of cleanups :("

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Fix memory leak when calling irq_free_hwirqs()
  irqchip: spear_shirq: Fix interrupt offset
  irqchip: brcmstb-l2: Level-2 interrupts are edge sensitive
  irqchip: armada-370-xp: Mask all interrupts during initialization.

Fixes for 3.16-rc3; most importantly Jesse brings back VGA he took away
on a bunch of machines. Also a vblank fix for BDW and a power workaround
fix for VLV.

* tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
  drm/i915: only apply crt_present check on VLV
  drm/i915: Wait for vblank after enabling the primary plane on BDW

fix to a 3.15 commit.

* 'vmwgfx-fixes-3.16' of git://people.freedesktop.org/~thomash/linux:
  drm/vmwgfx: Fix incorrect write to read-only register v2:

mode fixes for tda998x.

* 'tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
  drm/i2c: tda998x: add some basic mode validation
  drm/i2c: tda998x: faster polling for edid
  drm/i2c: tda998x: move drm_i2c_encoder_destroy call

irq_free_hwirqs() always calls irq_free_descs() with a cnt == 0
which makes it a no-op since the interrupt count to free is
decremented in itself.

Fixes: 7b6ef126Signed-off-by: Keith Busch <keith.busch@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1404167084-8070-1-git-send-email-keith.busch@intel.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull ARM64 fixes from Catalin Marinas:
 - Exception level check at boot time (for completeness, not triggering
   any bug before)
 - I/D-cache synchronisation logic for huge pages
 - Config symbol typo

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: fix el2_setup check of CurrentEL
  arm64: mm: Make icache synchronisation logic huge page aware
  arm64: mm: Fix horrendous config typo

Update MAINTAINERS file for recently added reset controller, AEMIF
and clocksource driver for Keystone SOCs.

The EMIF memory controller driver is also added along with AEMIF.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The mach-mxs platform is actually co-maintained by myself and
pengutronix folks.  Also it's hosted in the same kernel tree as IMX.
So let's merge the entry into IMX one.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>