Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Xie <AlexBin.Xie@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Those should be 64bit, even on a 32bit system.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This update allows sensors to return more than 1 value and
indicates to the caller how many bytes are written.

The debugfs interface has been updated to handle reading all
of the values.  Simply seek to the enum value (multiplied
by 4) and then read as many bytes as the sensor provides.

(v2):  Don't set size to 4 before reading GPU_POWER
(v3): agd: rebase
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable/disable the handling globally for now and
print a warning when we enable it for the first time.

v2: set correct register
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable/disable the handling globally for now and
print a warning when we enable it for the first time.

v2: set correct register
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable/disable the handling globally for now and
print a warning when we enable it for the first time.

v2: write to the correct register, adjust bits to that hw generation
v3: fix compilation, add the missing register bit definitions
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Till GFX8 we can only enable PRT support globally, but with the next hardware
generation we can do this on a per page basis.

Keep the interface consistent by adding PRT mappings and enable
support globally on current hardware when the first mapping is made.

v2: disable PRT support delayed and on all error paths
v3: PRT and other permissions are mutal exclusive,
    PRT mappings don't need a BO.
v4: update PRT mappings durign CS as well, make va_flags 64bit
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Future hardware generations can handle PRT flags on a per page basis,
but current hardware can only turn it on globally.

Add the basic handling for both, a global callback to enable/disable
triggered by setting a per mapping flag.

v2: agd: rebase fixes
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

For PRT support we need mappings which aren't backed by any memory.

v2: fix parameter checking
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

no suspend invoked so after VF FLR by host, we just
call hw_init to reinitialize IPs.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The additional output are:
vddc power in Watt;
vddci power in Watt;
max gpu power in Watt;
average gpu power in Watt.
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

As well as fix print format for uint32_t type.
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Acked-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Acked-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Acked-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Acked-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Acked-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Acked-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add the sysfs entries pp_gfx_power_profile and
pp_compute_power_profile which give user a way to set
power profile through parameters minimum sclk, minimum mclk,
activity threshold, up hysteresis and down hysteresis only
when the entry power_dpm_force_performance_level is in
default value "auto". It is read and write. Example:

echo 500 800 20 0 5 > /sys/class/drm/card0/device/pp_*_power_profile

cat /sys/class/drm/card0/device/pp_*_power_profile
500 800 20 0 5

Note: first parameter is sclk in MHz, second is mclk in MHz,
third is activity threshold in percentage, fourth is up hysteresis
in ms and fifth is down hysteresis in ms.

echo set > /sys/class/drm/card0/device/pp_*_power_profile
To set power profile state if it exists.

echo reset > /sys/class/drm/card0/device/pp_*_power_profile
To restore default state and clear previous setting.
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Acked-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

this lock is used for sriov_gpu_reset, only get this mutex
can run into sriov_gpu_reset.

we have couple source triggers gpu_reset for SRIOV:
1) submit timedout and trigger reset voluntarily
2) invalid instruction detected by ENGINE and trigger reset voluntarily
2) hypervisor found world switch hang and trigger flr and notify guest to
   do reset.

all need take care and we need a mutex to protect the consistency of
reset routine.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

implement SRIOV gpu_reset for future use.
it wil be called from:
1) job timeout
2) privl access or instruction error interrupt
3) hypervisor detect VF hang

v2: agd: rebase on upstream
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

sw part only invoked once during sw_init.
hw part invoked during first drv load and resume later.

that way we cannot alloc mqd in hw/resume, we only keep
mqd allocted in sw_init routine.
and hw_init routine only kmap and set it.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We ultimately want to re-use this for bare metal,
so no need to have vf checks in the KIQ code itself
since kiq itself is currently only used in VF cases.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

this is for SRIOV fix:
mqd soft init/fini will be invoked by sw_init to
allocate BO for compute MQD resource, instead of
original scheme that hw_init allocates MQD.

because if hw_init allocates MQD, then resume will
allocate MQD, and that lead to memory leak after
driver recovered from hang.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

introduce a new mqd member in ring is for later usage.
we need keep a clean version of MQD for the purpose
of recovering compute rings from hang.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

CG & PG function changes engine clock/gating, which is
not appropriate for VF device, because one vf doesn't know
the whole picture of engine's overall workload.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

CPU is not efficient to clean framebuffer especially under
virtualization, then loading driver takes long time which causes
timeout of mailbox handshake.
Signed-off-by: Pixel Ding <Pixel.Ding@amd.com>
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

ib_pool init should prior to fbdev_init, otherwise
there will be error from amdgpu_sa_bo_new
(amdgpu_sa.c:323)

fbdev_init will call ttm_validate which further call
amdgpu_sa_bo_new.

v2:
move fbdev_init behind ib test.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

VF uses KIQ to access registers. When VM fault occurs, the driver
can't get back the fence of KIQ submission and runs into CPU soft
lockup.
Signed-off-by: Pixel Ding <Pixel.Ding@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When multiple VFs try to enter exclusive mode at the same time, the
looping mechansim doesn't help to ensure each can get it because it
only loops active VFs, then the last one has to wait for a long
interval.
Signed-off-by: Pixel Ding <Pixel.Ding@amd.com>
Reviewed-by: Xiangliang.Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

1,like pp_hw_init, we shouldn't report error if PP disabled
2,disable pp_en if sriov
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

From commit 73dec95e ("drm/i915: Emit to ringbuffer directly"),
copy_gma_to_hva() now returns copied data length instead of 0, so
need to change error return check for that.

Note: Looks this is caused by backmerge conflict resolving, so
4.11-rc4 is not impacted as commit 73dec95e ("drm/i915: Emit to
ringbuffer directly") is not in 4.11. But need to fix this before I
can apply 4.12 stuff against drm-intel-next correctly.

Fixes: e5c1ff14 ("Backmerge tag 'v4.11-rc4' into drm-next")
Cc: Dave Airlie <airlied@redhat.com>
Cc: Tina Zhang <tina.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Linux 4.11-rc4

The i915 GVT team need the rc4 code to base some more code on.