- 08 Apr, 2017 40 commits
-
-
Jordan Crouse authored
We should be detaching the MMU before destroying the address space. To do this cleanly, the detach has to happen in adreno_gpu_cleanup() because it needs access to structs in adreno_gpu.c. Plus it is better symmetry to have the attach and detach at the same code level. Signed-off-by:
Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by:
Rob Clark <robdclark@gmail.com>
-
Archit Taneja authored
3D mux is a small block placed after the DSPPs in MDP5. It can merge 2 LM/DSPP outputs and feed it to a single interface. Enable 3D Mux if our mdp5_pipeline has 2 active LMs. This check will need to be made more specific later when we add Dual DSI support with source split enabled. In that use case, each LM feeds to a separae INTF, so the 3D mux isn't needed. Signed-off-by:
Archit Taneja <architt@codeaurora.org> Signed-off-by:
-
Archit Taneja authored
Assigning LMs dynamically to CRTCs results in REG_MDP5_CTL_LAYER_REGs and REG_MDP5_CTL_LAYER_EXT_REGs maintaining old values for a LM that isn't used by our CTL instance anymore. Clear the ctl's CTL_LAYER_REG and CTL_LAYER_EXT_REGs for all LM instances. The ones that need to be configured are configured later in this func. Signed-off-by:
-
Archit Taneja authored
Dynamically assign a right mixer to mdp5_crtc_state in the CRTC's atomic_check path. Assigning the right mixer has some constraints, i.e, only a few LMs can be paired together. Update mdp5_mixer_assign to handle these constraints. Firstly, we need to identify whether we need a right mixer or not. At the moment, there are 2 scenarios where a right mixer might be needed: - If any of the planes connected to this CRTC is too wide (i.e, is comprised of 2 hwpipes). - If the CRTC's mode itself is too wide (i.e, a 4K mode on HDMI). We implement both these checks in the mdp5_crtc_atomic_check(), and pass 'need_right_mixer' to mdp5_setup_pipeline. If a CRTC is already assigned a single mixer, and a new atomic commit brings in a drm_plane that needs 2 hwpipes, we can successfully commit this mode without requiring a full modeset, provided that we still use the previously assigned mixer as the left mixer. If such an assignment isn't possible, we'd need to do a full modeset. This scenario has been ignored for now. The mixer assignment code is a bit messy, considering we have at most 4 LM instances in hardware. This can probably be re-visited later with simplified logic. Signed-off-by:
-
Archit Taneja authored
If a CRTC comprises of 2 LMs, it is mandatory to enable border out and assign it to the base stage. We had to enable border out also when the base plane wasn't fullscreen. Club these checks and put them in a separate function called get_start_stage() that returns the starting stage for assigning planes. Signed-off-by:
-
Archit Taneja authored
Now that our mdp5_planes can consist of 2 hwpipes, update the blend_setup() code to stage the right hwpipe to the left and right LMs Signed-off-by:
-
Archit Taneja authored
In order to enable Source Split in HW, we need to add/modify a few LM register configurations: - Configure the LM width to be half the mode width, so that each LM manages one half of the scanout. - Tell the 'right' LM that it is configured to be the 'right' LM in source split mode. - Since we now have 2 places where REG_MDP5_LM_BLEND_COLOR_OUT is configured, do a read-update-store for the register instead of directly writing a value to it. Signed-off-by:
-
Archit Taneja authored
Now that we have a right hwpipe in mdp5_plane_state, configure it mdp5_plane_mode_set(). The only parameters that vary between the left and right hwpipes are the src_w, src_img_w, src_x and crtc_x as we just even chop the fb into left and right halves. Add a mdp5_plane_right_pipe() which will be used by the crtc code to set up LM stages. Signed-off-by:
-
Archit Taneja authored
If the drm_plane has a source width that's greater than the max width supported by a SSPP (2560 pixels on 8x96), then we assign a 'r_hwpipe' to it in mdp5_plane_atomic_check(). TODO: There are a few scenarios where the hwpipe assignments aren't recommended by HW. For example, an assignment which results in a drm_plane to of two different types of hwpipes (say RGB0 on left and DMA1 on right) is not recommended. Also, hwpipes have a priority mapping, where the higher priority pipe needs to be staged on left LM, and the lower priority needs to be staged on the right LM. For example, the priority order for VIG pipes in decreasing order of priority is VIG0, VIG1, VIG2, and VIG3. So, VIG0 on left and VIG1 on right is a correct configuration, but VIG1 on left and VIG0 on right isn't. These scenarios are ignored for now for the sake of simplicity. Signed-off-by:
-
Archit Taneja authored
Refactor mdp5_plane_mode_set to call mdp5_hwpipe_mode_set. The latter func takes in only the hwpipe and the parameters that need to be programmed into the hwpipe registers. All the code that calculates these parameters is left as is in mdp5_plane_mode_set. In the future, when we let drm_plane be comprised of 2 hwpipes, this func allow us to configure each pipe without adding redundant code. Signed-off-by:
-
Archit Taneja authored
Add another mdp5_hw_mixer pointer (r_mixer) in mdp5_crtc_state. This mixer will be used to generate the right half of the scanout. With Source Split, a SSPP can now be connected to 2 Layer Mixers, but has to be at the same blend level (stage #) on both Layer Mixers. A drm_plane that has a lesser width than the max width supported, will comprise of a single SSPP/hwpipe, staged on both the Layer Mixers at the same blend level. A plane that is greater than max width will comprise of 2 SSPPs, with the 'left' SSPP staged on the left LM, and the 'right' SSPP staged on the right LM at the same blend level. For now, the drm_plane consists of only one SSPP, therefore, it needs to be staged on both the LMs in blend_setup() and mdp5_ctl_blend(). We'll extend this logic to support 2 hwpipes per plane later. The crtc cursor ops (using the LM cursors, not SSPP cursors) simply return an error if they're called when the right mixer is assigned to the CRTC state. With source split is enabled, we're expected to only SSPP cursors. This commit adds code that configures the right mixer, but the r_mixer itself isn't assigned at the moment. Signed-off-by:
-
Archit Taneja authored
Some of the newer MDP5 versions support Source Split of SSPPs. It is a feature that allows us to route the output of a hwpipe to 2 Layer Mixers. This is required to achieve the following use cases: - Dual DSI: For high res DSI panels (such as 2560x1600 etc), a single DSI interface doesn't have the bandwidth to drive the required pixel clock. We use 2 DSI interfaces to drive the left and right halves of the panel (i.e, 1280x1600 each). The MDP5 pipeline here would look like: LM0 -- DSPP0 -- INTF1 -- DSI1 / hwpipe-- \ LM1 -- DSPP1 -- INTF2 -- DSI2 A single hwpipe is used to scan out the left and right halves to DSI1 and DSI2 respectively. In order to do this, we need to configure the 2 Layer Mixers in Source Split mode. - HDMI 4K: In order to support resolutions with width higher than the max width supported by a hwpipe, we club 2 hwpipes together: hwpipe1 --- LM0 -- DSPP0 - - \ - -- 3D Mux -- INTF0 -- HDMI - - / hwpipe2 --- LM1 -- DSPP1 hwpipe1 is staged on the 'left' Layer Mixer, and hwpipe2 is staged on the 'right' Layer Mixer. An additional block called the '3D Mux' is used to merge the output of the 2 DSPPs to a single interface. In this use case, it is possible that a 4K surface is downscaled and placed completely within one of the halves. In order to support such scenarios (and keep the programming simple), Layer Mixers with Source Split can be assigned 2 hw pipes per stage. While scanning out, the HW takes care of fetching the pixels fom the correct pipe. Add a MDP cap to tell whether the HW supports source split or not. Add a MDP LM cap that tells whether a LM instance can operate in source split mode (and generate the 'left' part of the display output). Signed-off-by: -
Archit Taneja authored
These are a part of CRTC state, it doesn't feel nice to leave them hanging in mdp5_ctl struct. Pass mdp5_pipeline pointer instead wherever it is needed. We still have some params in mdp5_ctl like start_mask etc which are derivative of atomic state, and should be rolled back if a commit fails, but it doesn't seem to cause much trouble. Signed-off-by:
-
Archit Taneja authored
In the last few commits, we've been adding params to mdp5_crtc_state, and assigning them in the atomic_check() funcs. Now it's time to actually start using them. Remove the duplicated params from the mdp5_crtc struct, and start using them in the mdp5_crtc code. The majority of the references to these params is in code that executes after the atomic swap has occurred, so it's okay to use crtc->state in them. There are a couple of legacy LM cursor ops that may not use the updated state, but (I think) it's okay to live with that. Now that we dynamically allocate a mixer to the CRTC, we can also remove the static assignment to it in mdp5_crtc_init, and also drop the code that skipped init-ing WB bound mixers (those will now be rejected by mdp5_mixer_assign()). Signed-off-by:
-
Archit Taneja authored
Things like vblank/err irq masks, mode of operation (command mode or not) are derivative of the interface and mixer state. Therefore, they need to be a part of the CRTC state too. Add them to mdp5_crtc_state, and assign them in the CRTC's atomic_check() func, so that it can be rolled back to a clean state. Signed-off-by:
-
Archit Taneja authored
The INTF and CTL used in a display pipeline are going to be maintained as a part of the CRTC state (i.e, in mdp5_crtc_state). These entities, however, are currently statically assigned to drm_encoders (i.e. mdp5_encoder). Since these aren't directly visible to the CRTC, we assign them to the CRTC state in the encoder's atomic_check() op. With this approach, we assign portions of CRTC state in two different places: the layer mixer in CRTC's atomic_check(), and the INTF and CTL pieces in the encoder's atomic_check() op. We'd have more options here if the drm core maintained encoder state too, but the current approach of clubbing everything in CRTC's state works just fine. Unlike hwpipes and mixers, we don't need to keep a track of INTF/CTL assignments in the global atomic state. This is because they're currently not sharable resources. For example, INTF0 and CTL0 will always be assigned to one drm_encoder. This can change later when we implement writeback and want a CRTC to use a CTL for a while, and then release it for others to use it. Or, when a drm_encoder can switch between using a single INTF vs 2 INTFs. Signed-off-by:
-
Archit Taneja authored
Add the stuff needed to allow dynamically assigning a mixer to a CRTC. Since mixers are a resource that can be shared across multiple CRTCs, we need to maintain a 'hwmixer_to_crtc' map in the global atomic state, acquire the mdp5_kms.state_lock modeset lock and so on. The mixer is assigned in the CRTC's atomic_check() func, a failure will result in the new state being cleanly rolled back. The mixer assignment itself is straightforward, and almost identical to what we do for hwpipes. We don't need to grab the old hwmixer_to_crtc state like we do in hwpipes since we don't need to compare anything with the old state at the moment. The only LM capability we care about at the moment is whether the mixer instance can be used to display stuff (i.e, connect to an INTF downstream). Signed-off-by:
-
Archit Taneja authored
Subclass drm_crtc_state so that we can maintain additional state for our CRTCs. Add mdp5_pipeline and mdp5_ctl pointers in the subclassed state. mdp5_pipeline is a grouping of the HW entities that forms the downstream pipeline for a particular CRTC. It currently contains pointers to mdp5_interface and mdp5_hw_mixer tied to this CRTC. Later, we will have 2 hwmixers in this struct. (We could also have 2 intfs if we want to support dual DSI with Source Split enabled. Implementing that feature isn't planned at the moment). The mdp5_pipeline state isn't used at the moment. For now, we just introduce mdp5_crtc_state and the crtc funcs needed to manage the subclassed state. Signed-off-by:
-
Archit Taneja authored
The mdp5_ctl has an 'op_mode' struct which contains info on the downstream pipeline. Grouping these params together in a struct doesn't serve much purpose in the code. Maybe there was a plan to expand this further that never happened. Remove the op_mode struct, and place its members directly in mdp5_ctl. This will help avoid confusion later when I introduce my own verion of a mdp5 pipeline :) Signed-off-by:
-
Archit Taneja authored
mdp5_interface struct contains data corresponding to a INTF instance in MDP5 hardware. This sturct is memcpy'd to the mdp5_encoder struct, and then later to the mdp5_ctl struct. Instead of copying around interface data, create mdp5_interface instances in mdp5_init, like how it's done currently done for pipes and layer mixers. Pass around the interface pointers to mdp5_encoder and mdp5_ctl. This simplifies the code, and allows us to decouple encoders from INTFs in the future if needed. Signed-off-by:
-
Archit Taneja authored
PingPong ID for a Layer Mixer is already contained in mdp5_hw_mixer. This avoids the need to retrieve PP ID using macros Signed-off-by:
-
Archit Taneja authored
Use the mdp5_hw_mixer struct in the mdp5_crtc and mdp5_ctl instead of using the LM index. Like before, the Layer Mixers are assigned statically to the CRTCs. The hwmixer(s) will later be dynamically assigned to CRTCs. For now, ignore the hwmixers that can only do WB. Signed-off-by:
-
Archit Taneja authored
Create a struct to represent MDP5 Layer Mixer instances. This will eventually allow us to detach CRTCs from the Layer Mixers, and generally clean things up a bit. This is very similar to how hwpipes were previously abstracted away from drm planes. Signed-off-by:
-
Archit Taneja authored
The number of Layer Mixers and the downstream blocks (DSPPs and PPs) connected to each LM can vary with different MDP5 revisions. These parameters are also static. Keep the per instance LM data in mdp5_cfg. This will avoid the need to have macros which identify PP id or DSPP id the LM is connected to. We don't configure DSPPs at the moment, but keeping the DSPP instance # here might come handy later. Also add a 'caps' field that identifies features supported by a LM instance. Introduce the caps MDP_LM_CAP_DISPLAY and MDP_LM_CAP_WB that identify whether a LM instance can be used for display or writeback. Signed-off-by:
-
Archit Taneja authored
We'd previously moved the pipe_lock spinlock to the hwpipe struct. Bring it back to mdp5_plane. We will need this because an mdp5_plane in the future could comprise of 2 hw pipes. It makes more sense to have a single lock to protect the registers for the hw pipes used by a plane, rather than trying to take individual locks per hwpipe when committing a configuration. Signed-off-by:
-
Vinay Simha BN authored
4 macros already defined in hdmi.h, which is not required to redefine in hdmi_audio.c Signed-off-by:
Vinay Simha BN <simhavcs@gmail.com> Signed-off-by:
-
Archit Taneja authored
'SSPP_MAX + 1' is the max number of hwpipes that can be present on a MDP5 platform. Recently, 2 new cursor hwpipes were added, which caused overflows in arrays that used SSPP_MAX to represent the number of elements. Update the SSPP_MAX value to incorporate the extra hwpipes. Signed-off-by:
-
Archit Taneja authored
A recent commit introduces a bug in dsi_mgr_phy_enable. In the non dual DSI mode, we reset the mdsi (master DSI) PHY. This isn't right since master and slave DSI exist only in dual DSI mode. For the normal mode of operation, we should simply reset the PHY of the DSI device (i.e. msm_dsi) corresponding to the current bridge. Usage of the wrong DSI pointer also resulted in a static checker warning. That too is resolved with this fix. Fixes: b62aa70a (drm/msm/dsi: Move PHY operations out of host) Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Jordan Crouse authored
Zero sized buffer objects tend to make various bits of the GEM infrastructure complain: WARNING: CPU: 1 PID: 2323 at drivers/gpu/drm/drm_mm.c:389 drm_mm_insert_node_generic+0x258/0x2f0 Modules linked in: CPU: 1 PID: 2323 Comm: drm-api-test Tainted: G W 4.9.0-rc4-00906-g693af44 #213 Hardware name: Qualcomm Technologies, Inc. DB820c (DT) task: ffff8000d7353400 task.stack: ffff8000d7720000 PC is at drm_mm_insert_node_generic+0x258/0x2f0 LR is at drm_vma_offset_add+0x4c/0x70 Zero sized buffers serve no appreciable value to the user so disallow them at create time. Signed-off-by:
-
Jordan Crouse authored
Output the upper 32 bits of a 64 bit iova in the RD_CMDSTREAM_ADDR section while maintaining backwards compatibility for tools that only understand 32 bit iovas. Signed-off-by:
-
Jordan Crouse authored
The interrupt status was being cleared before processing the handlers. a5xx_rbbm_err_irq() was checking the interrupt status again, which would likely turn out bad because the interrupt status would be 0 (or at least different). Pass the original status to the function instead. Also, skip clearing RBBM_AHB_ERROR from the interrupt status. The interrupt will keep firing until the error source is cleared. Skip the clear to avoid a storm until the error is cleared in a5xx_rbbm_err_irq(). Signed-off-by:
-
Jordan Crouse authored
priv->num_aspaces is increased and then checked to see if it still fits in the priv->aspace array. If it doesn't, we warn and exit but priv->num_aspaces remains incremented. Don't incremement the count until we know that it fits in the array. Signed-off-by:
-
Jordan Crouse authored
Instead of checking for a5xx_gpu->gpmu_iova during destroy we accidently check a5xx_gpu->gpmu_bo. Signed-off-by:
-
Daniel Vetter authored
The core takes care of handling the send_event vs. close() issues, we can remove that driver code. Cc: Rob Clark <robdclark@gmail.com> Cc: linux-arm-msm@vger.kernel.org Cc: freedreno@lists.freedesktop.org Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Signed-off-by:
-
Daniel Vetter authored
I didn't spot anything that would require ordering here (well not anywhere else either), and I'm trying to unify at least modern drivers on one close hook. Cc: Rob Clark <robdclark@gmail.com> Cc: linux-arm-msm@vger.kernel.org Cc: freedreno@lists.freedesktop.org Signed-off-by:
-
Arnd Bergmann authored
The newly added a5xx support fails to build when debugfs is diabled: drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:4: error: 'struct msm_gpu_funcs' has no member named 'show' drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:11: error: 'a5xx_show' undeclared here (not in a function); did you mean 'a5xx_irq'? This adds a missing #ifdef. Fixes: b5f103ab ("drm/msm: gpu: Add A5XX target support") Cc: stable@vger.kernel.org Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Rob Clark authored
Probably a symptom of needing finer grained locking, but if we wait on the incoming fence-fd (which could come from a different context) while holding struct_mutex, that blocks retire_worker so gpu fences cannot get signalled. This causes a problem if userspace manages to get more than a frame ahead, leaving the atomic-commit worker blocked waiting on fences that cannot be signaled because submit is blocked waiting for a fence signalled from vblank (after the atomic commit which is blocked). If we start having multiple fence ctxs for the gpu, submit_fence_sync() would probably need to move outside of struct_mutex as well. Signed-off-by: -
Rob Clark authored
In particular, attach() and unmap() need pm-runtime get/put to ensure iommu clks are enabled. Signed-off-by: -
Rob Clark authored
Significantly simplifies things. Also iommu_unmap() can unmap an entire iova range. (If backporting to downstream kernel you might need to revert this. Or at least double check older iommu implementation.) Signed-off-by: -
Rob Clark authored
We need to do this also in resume path when we need to re-hw_init(). Signed-off-by:
-
