- atomic bit operations are globally visible
- pending status is always cleared before execution
- scheduled works are either idempotent or only required to happen once
  after a series of originating events, say link events for instance
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>

With infinite gratitude to Eric Dumazet for allowing me to identify
the error.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>

   text	   data	    bss	    dec	    hex	filename
8455963	 532732	1810804	10799499 a4c98b	vmlinux.o.before
8448899	 532732	1810804	10792435 a4adf3	vmlinux.o

This change also removes commented-out copy of __nlmsg_put
which was last touched in 2005 with "Enable once all users
have been converted" comment on top.

Changes in v2: rediffed against net-next.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC5722 Section 4 was amended by Errata 3089

Our implementation did the right thing anyway...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ability to return neighbour proxies list to caller if
it sent full ndmsg structure and has NTF_PROXY flag set.

Before this patch (and before iproute2 patches):
$ ip neigh add proxy 2001::1 dev eth0
$ ip -6 neigh show
$

After it and with applied iproute2 patches:
$ ip neigh add proxy 2001::1 dev eth0
$ ip -6 neigh show
2001::1 dev eth0  proxy
$

Compatibility with old versions of iproute2 is not broken,
kernel checks for incoming structure size and properly
works if old structure is came.

[v2]
* changed comments style.
* removed useless line with continue and curly bracket.
* changed incoming message size check from equal to more or
  equal.

CC: davem@davemloft.net
CC: kuznet@ms2.inr.ac.ru
CC: netdev@vger.kernel.org
CC: xemul@parallels.com
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This code is clearly unused, since it has a #error right
in it.  Given the vintage of sun3 hardware, it is probably
safe to assume that there is little interest in adding new
functionality to the driver now, so just delete the unused
block of code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Sam Creasey <sammy@sammy.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reorganization of the driver layout in drivers/net
left behind some stale paths in comments and in Kconfig
help text.  Bring them up to date.  No actual change to
any code takes place here.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function returns the page offset of the buffer, which can be
calculated based on either its DMA address or its virtual address.  It
used to use the virtual address and we would cast that to unsigned
long, as anything smaller would result in a compiler warning.  Now
that it's using the DMA address we should use unsigned int, matching
the return type.  It is also unnecessary to use __force.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

<linux/mtd/mtd.h> no longer defines DEBUG so we do not need to
un-define it here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

It's only used to get at neigh->primary_key, which in this context is
always going to be the same as rt->rt6i_gateway.
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead, compute it as-needed inside of that function using
dst_neigh_lookup().
Signed-off-by: David S. Miller <davem@davemloft.net>

In this specific situation we know we are dealing with a gatewayed route
and therefore rt6i_gateway is not going to be in6addr_any even in future
interpretations.
Signed-off-by: David S. Miller <davem@davemloft.net>

Now all code paths grab a local reference to the neigh, so if neigh
is not NULL we unconditionally release it at the end.  The old logic
would only release if we didn't have a non-NULL 'rt'.
Signed-off-by: David S. Miller <davem@davemloft.net>

The conversion is very similar to that made to ipv6's SIT code.
Signed-off-by: David S. Miller <davem@davemloft.net>

The irq handler was a mess.

See 7ab87ff4 ("via-rhine: move work from
irq handler to softirq and beyond") for similar changes. One can notice:
- all non-napi tasks are explicitely scheduled trough a single work queue.
- hiding software tx queue start behind the rtl_hw_start method is mildly
  natural. Move it in the caller where needed.
- as can be seen from the heavy use of bh disabling locks, the driver is
  not safe for irq context messages with netconsole. It is still quite
  usable for general messaging though. Tested ok with concurrent registers
  dump (ethtool -d) + background traffic + "echo t > /proc/sysrq-trigger".

Tested with old PCI chipset, PCIe 8168 and 810x:
- XID 0c900800 RTL8168evl/8111evl
- XID 18000000 RTL8168b/8111b
- XID 98000000 RTL8169sc/8110sc
- XID 083000c0 RTL8168d/8111d
- XID 081000c0 RTL8168d/8111d
- XID 00b00000 RTL8105e
- XID 04a00000 RTL8102e

As a side note, the comments in f11a377b
("r8169: avoid losing MSI interrupts") does not seem completely clear: if
I hack the driver further to stop acking the irq link event bit, MSI
interrupts keep being delivered (RTL8168b/8111b, XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Though motivated by the move of the driver to a single work queue of
sequential events and removal of hard irq processing, it looks safe as
a standalone change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

I see no good reason to keep both rtl8169_reinit_task and rtl8169_reset_task:
- rtl8169_reinit_task adds a software failure point which does relate to
  any hardware state
- they handle hardware the same. Remember that rtl8169_reinit_task was
  introduced in the 8169 only era to handle PCI errors way before the 8168
  asked for pll and firmware ops and compare :

      rtl8169_reinit_task     |    rtl8169_reset_task
  ----------------------------+--------------------------
  rtl8169_wait_for_quiescence | rtl8169_hw_reset
  rtl8169_update_counters     | rtl8169_wait_for_quiescence
  rtl8169_hw_reset            | rtl_hw_start
  rtl8169_rx_missed           | rtl8169_check_link_status
  rtl_pll_power_down          |
  rtl_request_firmware        |
  rtl8169_init_phy            |
  rtl_pll_power_up            |
  rtl_hw_start                |
  rtl8169_check_link_status   |
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The generic lib.c file contains code relative to the various MACs, NVM and
Manageability supported by the driver.  This patch splits the file into
three which are specific to those areas similar to how the PHY-specific
code is in phy.c and code specific to the 80003es2lan, 8257x, and ichX
MAC families are in their own files.  The generic code that is applicable
to all MAC/PHY parts supported by the driver remains in netdev.c, param.c
and ethtool.c files.  No change in functionality, just moving code
around for ease of maintenance, with some whitespace and other checkpatch
cleanups.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

__er16flash() is not meant to be called directly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Convert the last instances of strncpy() to the preferred strlcpy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

To ease searching for debug message strings, concatenate strings that span
multiple lines even if the resulting line exceeds 80 columns; these will
not cause checkpatch warnings.

Also, add '\n' and remove unnecessary '\r' from a few debug strings.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When setting the Low Power Link Up (LPLU, a.k.a. reverse auto-negotiation)
on 82577/8278/82579, do not restart auto-negotiation if reset of the Phy is
blocked by the Manageability Engine.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

During bi-directional stress on some 82566/82567 devices, some received
packets were dropped.  Increasing the Receive Packet Buffer Allocation
resolves this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When going to Sx with an ICHx/PCH device, the default Low Power Link Up
(LPLU, a.k.a. reverse auto-negotiation) behavior should be whatever is set
in the NVM.  However, the function e1000_suspend_workarounds_ich8lan()
called when going to Sx always enabled LPLU in all power states.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The workaround which toggles the LANPHYPC (LAN PHY Power Control) value bit
to force the MAC-Phy interconnect into PCIe mode from SMBus mode during
driver load and resume should always be done except if PHY resets are
blocked by the Manageability Engine (ME).  Previously, the toggle was done
only if PHY resets are blocked and the ME was disabled.

The rest of the patch is just indentation changes as a consequence of the
updated workaround.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Internal stress testing with jumbo frames shows the reliability of ICH9 and
ICH10D devices is improved in certain corner cases by disabling the Early
Receive feature. To reduce the performance impact caused by disabling this
feature, the packet buffer sizes and relevant flow control settings are
modified accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace checksummed and discard booleans from efx_handle_rx_event()
with a bitmask, added to the flags field.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Currently we use type u64 for byte counts, which can very quickly
exceed 2^32, and unsigned long for packet counts, which do not.  But
it can still take only 20-something minutes to send or receive 2^32
packets, and not all tools properly handle overflow even if they
sample more often than this.

The MAC statistics are all updated synchronously, so it costs very
little to make them all 64-bit regardless of native word size.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Rename efx_set_multicast_list() to efx_set_rx_mode(), in line
with the operation name net_device_ops::ndo_set_rx_mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>