Pull i2c updates from Wolfram Sang:
 - new drivers: Kontron PLD, Wondermedia VT
 - mv64xxx driver gained sun4i support and a bigger cleanup
 - duplicate driver 'intel-mid' removed
 - added generic device tree binding for sda holding time (and
   designware driver already uses it)
 - we tried to allow driver probing with only device tree and no i2c
   ids, but I had to revert it because of side effects.  Needs some
   rethinking.
 - driver bugfixes, cleanups...

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
  i2c-designware: use div_u64 to fix link
  i2c: Kontron PLD i2c bus driver
  i2c: iop3xxx: fix build failure after waitqueue changes
  i2c-designware: make SDA hold time configurable
  i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided
  i2c: imx: allow autoloading on dt ids
  i2c: mv64xxx: Fix transfer error code
  i2c: i801: SMBus patch for Intel Coleto Creek DeviceIDs
  i2c: omap: correct usage of the interrupt enable register
  i2c-pxa: prepare clock before use
  Revert "i2c: core: make it possible to match a pure device tree driver"
  i2c: nomadik: allocate adapter number dynamically
  i2c: nomadik: support elder Nomadiks
  i2c: mv64xxx: Add Allwinner sun4i compatible
  i2c: mv64xxx: make the registers offset configurable
  i2c: mv64xxx: Add macros to access parts of registers
  i2c: vt8500: Add support for I2C bus on Wondermedia SoCs
  i2c: designware: fix race between subsequent xfers
  i2c: bfin-twi: Read and write the FIFO in loop
  i2c: core: make it possible to match a pure device tree driver
  ...

Pull first round of SCSI updates from James Bottomley:
 "The patch set is mostly driver updates (usf, zfcp, lpfc, mpt2sas,
  megaraid_sas, bfa, ipr) and a few bug fixes.  Also of note is that the
  Buslogic driver has been rewritten to a better coding style and 64 bit
  support added.  We also removed the libsas limitation on 16 bytes for
  the command size (currently no drivers make use of this)"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (101 commits)
  [SCSI] megaraid: minor cut and paste error fixed.
  [SCSI] ufshcd-pltfrm: remove unnecessary dma_set_coherent_mask() call
  [SCSI] ufs: fix register address in UIC error interrupt handling
  [SCSI] ufshcd-pltfrm: add missing empty slot in ufs_of_match[]
  [SCSI] ufs: use devres functions for ufshcd
  [SCSI] ufs: Fix the response UPIU length setting
  [SCSI] ufs: rework link start-up process
  [SCSI] ufs: remove version check before IS reg clear
  [SCSI] ufs: amend interrupt configuration
  [SCSI] ufs: wrap the i/o access operations
  [SCSI] storvsc: Update the storage protocol to win8 level
  [SCSI] storvsc: Increase the value of scsi timeout for storvsc devices
  [SCSI] MAINTAINERS: Add myself as the maintainer for BusLogic SCSI driver
  [SCSI] BusLogic: Port driver to 64-bit.
  [SCSI] BusLogic: Fix style issues
  [SCSI] libiscsi: Added new boot entries in the session sysfs
  [SCSI] aacraid: Fix for arrays are going offline in the system. System hangs
  [SCSI] ipr: IOA Status Code(IOASC) update
  [SCSI] sd: Update WRITE SAME heuristics
  [SCSI] fnic: potential dead lock in fnic_is_abts_pending()
  ...

Pull trivial tree updates from Jiri Kosina:
 "The usual stuff from trivial tree"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
  treewide: relase -> release
  Documentation/cgroups/memory.txt: fix stat file documentation
  sysctl/net.txt: delete reference to obsolete 2.4.x kernel
  spinlock_api_smp.h: fix preprocessor comments
  treewide: Fix typo in printk
  doc: device tree: clarify stuff in usage-model.txt.
  open firmware: "/aliasas" -> "/aliases"
  md: bcache: Fixed a typo with the word 'arithmetic'
  irq/generic-chip: fix a few kernel-doc entries
  frv: Convert use of typedef ctl_table to struct ctl_table
  sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
  doc: clk: Fix incorrect wording
  Documentation/arm/IXP4xx fix a typo
  Documentation/networking/ieee802154 fix a typo
  Documentation/DocBook/media/v4l fix a typo
  Documentation/video4linux/si476x.txt fix a typo
  Documentation/virtual/kvm/api.txt fix a typo
  Documentation/early-userspace/README fix a typo
  Documentation/video4linux/soc-camera.txt fix a typo
  lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
  ...

Pull HID updates from Jiri Kosina:
 - HID battery handling cleanup by David Herrmann
 - ELO 4000/4500 driver, which has been finally ported to be proper HID
   driver by Jiri Slaby
 - ps3remote driver functionality is now provided by generic sony
   driver, by Jiri Kosina
 - PS2/3 Buzz controllers support, by Colin Leitner
 - rework of wiimote driver including full extensions hotpluggin
   support, sub-device modularization and speaker support by David
   Herrmann

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (55 commits)
  HID: wacom: Intuos4 battery charging changes
  HID: i2c-hid: support sending HID output reports using the output register
  HID: kye: Add report fixup for Genius Gila Gaming mouse
  HID: wiimote: support Nintendo Wii U Pro Controller
  Input: make gamepad API keycodes more clear
  input: document gamepad API and add extra keycodes
  HID: explain out-of-range check better
  HID: fix false positive out of range values
  HID: wiimote: fix coccinelle warnings
  HID: roccat: check cdev_add return value
  HID: fold ps3remote driver into generic Sony driver
  HID: hyperv: convert alloc+memcpy to memdup
  HID: core: fix reporting of raw events
  HID: wiimote: discard invalid EXT data reports
  HID: wiimote: fix classic controller parsing
  HID: wiimote: init EXT/MP during device detection
  HID: wiimote: fix DRM debug-attr to correctly parse input
  HID: wiimote: add MP quirks
  HID: wiimote: remove old static extension support
  HID: wiimote: add "bboard_calib" attribute
  ...

Pull md updates from NeilBrown:
 "Mostly fixes, with a few minor features (eg 'last_sync_action' sysfs
  file)

  A couple marked for -stable including one recent bug which causes a
  RAID10 reshape to complete without moving any data :-(

  A couple more bugfixes (at least) to come, but haven't confirmed the
  right solution yet."

* tag 'md-3.11' of git://neil.brown.name/md:
  md/raid10: fix bug which causes all RAID10 reshapes to move no data.
  md/raid5: allow 5-device RAID6 to be reshaped to 4-device.
  md/raid10: fix two bugs affecting RAID10 reshape.
  md: remove doubled description for sync_max, merging it within sync_min/sync_max
  MD: Remember the last sync operation that was performed
  md: fix buglet in RAID5 -> RAID0 conversion.
  md/raid10: check In_sync flag in 'enough()'.
  md/raid10: locking changes for 'enough()'.
  md: replace strict_strto*() with kstrto*()
  md: Wait for md_check_recovery before attempting device removal.
  dm-raid: silence compiler warning on rebuilds_per_group.
  DM RAID: Fix raid_resume not reviving failed devices in all cases
  DM RAID: Break-up untidy function
  DM RAID: Add ability to restore transiently failed devices on resume

Merge Kconfig menu diet patches from Dave Hansen:
 "I think the "Kernel Hacking" menu has gotten a bit out of hand.  It is
  over 120 lines long on my system with everything enabled and options
  are scattered around it haphazardly.

        http://sr71.net/~dave/linux/kconfig-horror.png

  Let's try to introduce some sanity.  This set takes that 120 lines
  down to 55 and makes it vastly easier to find some things.  It's a
  start.

  This set stands on its own, but there is plenty of room for follow-up
  patches.  The arch-specific debug options still end up getting stuck
  in the top-level "kernel hacking" menu.  OPTIMIZE_INLINING, for
  instance, could obviously go in to the "compiler options" menu, but
  the fact that it is defined in arch/ in a separate Kconfig file keeps
  it on its own for the moment.

  The Signed-off-by's in here look funky.  I changed employers while
  working on this set, so I have signoffs from both email addresses"

* emailed patches from Dave Hansen <dave@sr71.net>:
  hang and lockup detection menu
  kconfig: consolidate printk options
  group locking debugging options
  consolidate compilation option configs
  consolidate runtime testing configs
  order memory debugging Kconfig options
  consolidate per-arch stack overflow debugging options

The hard/softlockup and hung-task entries take up 6 lines
of screen real-estate when enabled.  I bet folks don't
mess with these _that_ often, so move them in a group
down a level.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Same deal, take the printk-related things and hide them in a menu.
This takes another 4 items out of the top-level menu.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Original posting:

	http://lkml.kernel.org/r/20121214184208.D9E5804D@kernel.stglabs.ibm.com

There are quite a few of these, and we want to make sure that
there is one-stop-shopping for lock debugging.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Original Post:

	http://lkml.kernel.org/r/20121214184207.6E00DDEC@kernel.stglabs.ibm.com

Again, trying to come up with some common themes of the stuff in
the kernel hacking menu...  There are quite a few options to
tweak compilation in some way, or perform extra compile-time
checks.  Give them their own menu.

The diff here looks a bit funny... makes it look like I'm
moving debugfs even though I'm actually moving the options on
either side of it.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Original posting:

	http://lkml.kernel.org/r/20121214184206.FC11422F@kernel.stglabs.ibm.com

These runtime tests are great, except that there are a lot of them,
and they are very rarely needed.  Give them their own menu so that
only the folks who need them will have to go looking for them.

Note that there are some other runtime tests that are not in here,
like for RCU or locking.  This menu should only be used for tests
that do not have a more appropriate home.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Original posting:

	http://lkml.kernel.org/r/20121214184203.37E6C724@kernel.stglabs.ibm.com

There are a *LOT* of memory debugging options.  They are just scattered
all over the "Kernel Hacking" menu.  Sure, "memory debugging" is a very
vague term and it's going to be hard to make absolute rules about what
goes in here, but this has to be better than what we had before.

This does, however, leave out the architecture-specific memory
debugging options (like x86's DEBUG_SET_MODULE_RONX).  There would need
to be some substantial changes to move those in here.  Kconfig can not
easily mix arch-specific and generic options together: it really
requires a file per-architecture, and I think having an
arch/foo/Kconfig.debug-memory might be taking things a bit too far
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Original posting:

	http://lkml.kernel.org/r/20121214184202.F54094D9@kernel.stglabs.ibm.com

Several architectures have similar stack debugging config options.
They all pretty much do the same thing, some with slightly
differing help text.

This patch changes the architectures to instead enable a Kconfig
boolean, and then use that boolean in the generic Kconfig.debug
to present the actual menu option.  This removes a bunch of
duplication and adds consistency across arches.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [for tile]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge hpfs patches from Mikulas Patocka.

* emailed patches from Mikulas Patocka <mpatocka@artax.karlin.mff.cuni.cz>:
  hpfs: implement prefetch to improve performance
  hpfs: use mpage
  hpfs: better test for errors

This patch implements prefetch to improve performance.  It helps mostly
when scanning the bitmaps to calculate free space.
Signed-off-by: Mikulas Patocka <mpatocka@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use the mpage interface to improve performance.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The test if bitmap access is out of bound could errorneously pass if the
device size is divisible by 16384 sectors and we are asking for one bitmap
after the end.

Check for invalid size in the superblock. Invalid size could cause integer
overflows in the rest of the code.
Signed-off-by: Mikulas Patocka <mpatocka@artax.karlin.mff.cuni.cz>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull powerpc updates from Ben Herrenschmidt:
 "This is the powerpc changes for the 3.11 merge window.  In addition to
  the usual bug fixes and small updates, the main highlights are:

   - Support for transparent huge pages by Aneesh Kumar for 64-bit
     server processors.  This allows the use of 16M pages as transparent
     huge pages on kernels compiled with a 64K base page size.

   - Base VFIO support for KVM on power by Alexey Kardashevskiy

   - Wiring up of our nvram to the pstore infrastructure, including
     putting compressed oopses in there by Aruna Balakrishnaiah

   - Move, rework and improve our "EEH" (basically PCI error handling
     and recovery) infrastructure.  It is no longer specific to pseries
     but is now usable by the new "powernv" platform as well (no
     hypervisor) by Gavin Shan.

   - I fixed some bugs in our math-emu instruction decoding and made it
     usable to emulate some optional FP instructions on processors with
     hard FP that lack them (such as fsqrt on Freescale embedded
     processors).

   - Support for Power8 "Event Based Branch" facility by Michael
     Ellerman.  This facility allows what is basically "userspace
     interrupts" for performance monitor events.

   - A bunch of Transactional Memory vs.  Signals bug fixes and HW
     breakpoint/watchpoint fixes by Michael Neuling.

  And more ...  I appologize in advance if I've failed to highlight
  something that somebody deemed worth it."

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (156 commits)
  pstore: Add hsize argument in write_buf call of pstore_ftrace_call
  powerpc/fsl: add MPIC timer wakeup support
  powerpc/mpic: create mpic subsystem object
  powerpc/mpic: add global timer support
  powerpc/mpic: add irq_set_wake support
  powerpc/85xx: enable coreint for all the 64bit boards
  powerpc/8xx: Erroneous double irq_eoi() on CPM IRQ in MPC8xx
  powerpc/fsl: Enable CONFIG_E1000E in mpc85xx_smp_defconfig
  powerpc/mpic: Add get_version API both for internal and external use
  powerpc: Handle both new style and old style reserve maps
  powerpc/hw_brk: Fix off by one error when validating DAWR region end
  powerpc/pseries: Support compression of oops text via pstore
  powerpc/pseries: Re-organise the oops compression code
  pstore: Pass header size in the pstore write callback
  powerpc/powernv: Fix iommu initialization again
  powerpc/pseries: Inform the hypervisor we are using EBB regs
  powerpc/perf: Add power8 EBB support
  powerpc/perf: Core EBB support for 64-bit book3s
  powerpc/perf: Drop MMCRA from thread_struct
  powerpc/perf: Don't enable if we have zero events
  ...

Intuos4 WL is separately reporting power supply and battery
charging status - now hid-wacom is using that information.
Previously hid-wacom was wrongly treating "battery charging" bit
as "power supply connected". Now it should report battery charging,
battery discharging, battery full and power supply status.

Intuos4 WL sends reports when is in use (obvious) and when unplugging
power supply. If means that if the device is being charged, but it's not
being used it will never report "battery full". The same problem happens
after the device has been connected, but it's not in use - the
battery/ac status will be incorrect. Currently there is no mechanism to
ask the device to send a report containing battery/ac status.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Conflicts:
	drivers/hid/hid-core.c

Merge branches 'for-3.11/battery', 'for-3.11/elo', 'for-3.11/holtek' and 'for-3.11/i2c-hid-fixed' into for-linus

The current i2c hid driver does not support sending HID output reports using
the output register for devices which support receiving reports through this
method. This patch determines which method to use to send output reports based
 on the value of wMaxOutputLength in the device's HID descriptor.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The recent comment:
commit 7e83ccbe
    md/raid10: Allow skipping recovery when clean arrays are assembled

Causes raid10 to skip a recovery in certain cases where it is safe to
do so.  Unfortunately it also causes a reshape to be skipped which is
never safe.  The result is that an attempt to reshape a RAID10 will
appear to complete instantly, but no data will have been moves so the
array will now contain garbage.
(If nothing is written, you can recovery by simple performing the
reverse reshape which will also complete instantly).

Bug was introduced in 3.10, so this is suitable for 3.10-stable.

Cc: stable@vger.kernel.org (3.10)
Cc: Martin Wilck <mwilck@arcor.de>
Signed-off-by: NeilBrown <neilb@suse.de>

There is a bug in 'check_reshape' for raid5.c  To checks
that the new minimum number of devices is large enough (which is
good), but it does so also after the reshape has started (bad).

This is bad because
 - the calculation is now wrong as mddev->raid_disks has changed
   already, and
 - it is pointless because it is now too late to stop.

So only perform that test when reshape has not been committed to.
Signed-off-by: NeilBrown <neilb@suse.de>

Pull hwmon updates from Guenter Roeck:
 - new driver to support GMT G762/G763 pwm fan controllers
 - add support for DS1631, DS1721, and DS1731 to ds1621 driver
 - remove detect function from ds1621 driver as unreliable
 - bug fixes in nct6775, iio_hwmon, and adm1021 drivers
 - remove redundant platform_set_drvdata in various drivers
 - add device tree support to ina2xx driver

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (ds1621) Fix temperature rounding operations
  hwmon: (nct6775) Drop unsupported fan alarm attributes for NCT6775
  hwmon: (nct6775) Fix temperature alarm attributes
  Add support for GMT G762/G763 PWM fan controllers
  hwmon: (ina2xx) Add device tree support to pass the shunt resistor
  hwmon: (ds1621) Update documentation
  hwmon: (ds1621) Add DS1731 chip support to ds1621 driver
  hwmon: (iio_hwmon) add alias table
  hwmon: (adm1021) Do not create min sysfs attributes for LM84
  hwmon: (ds1621) Remove detect function
  hwmon: (ds1621) Add ds1631 chip support to ds1621 driver and documentation
  hwmon: (ds1621) Add ds1721 update interval sysfs attribute
  hwmon: (ds1621) Add ds1721 chip support
  hwmon: (w83627ehf) Remove redundant platform_set_drvdata()
  hwmon: (ntc_thermistor) Remove redundant platform_set_drvdata()
  hwmon: (i5k_amb) Remove redundant platform_set_drvdata()
  hwmon: (coretemp) Remove redundant platform_set_drvdata()
  hwmon: (abituguru3) Remove redundant platform_set_drvdata()

Pull LED subsystem updates from Bryan Wu:
 - lp55xx device tree updates
 - mc13xxx driver updates
 - some clean up

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
  leds: mc13783: Fix "uninitialized variable" warning
  leds: Convert led class driver from legacy pm ops to dev_pm_ops
  leds: leds-mc13783: Add MC13892 LED support
  leds: leds-mc13783: Prepare driver to support MC13892 LEDs
  leds: renesas-tpu: cleanup a small type issue
  leds: use platform_{get,set}_drvdata()
  leds: leds-gpio: Let device core handle pinctrl
  leds: lp5562: Properly setup of_device_id table
  leds: lp5523: Properly setup of_device_id table
  leds: lp5521: Properly setup of_device_id table
  leds: lp5562: support the device tree feature
  leds: lp55xx: support dynamic channel settings in the device tree structure
  leds: leds-ns2: remove unnecessary platform_set_drvdata()
  leds: leds-mc13783: remove unnecessary platform_set_drvdata()
  leds: leds-gpio: remove unnecessary platform_set_drvdata()
  leds: atmel-pwm: remove unnecessary platform_set_drvdata()
  leds: lp55xx: add support for Device Tree bindings

Pull sound updates from Takashi Iwai:
 "A relative calm release at this time with a flat diffstat.  The only
  significant change in the ALSA core side is the support for more than
  32 card instances, configurable via kconfig.  Other than that, in both
  ASoC and other parts, mostly some improvements and fixes on the driver
  side.

   - hda: More quirks for ALC269-variants on Dell & co, VIA codec fixes
   - hda: Haswell HDMI audio fixes, runtime PM improvements
   - hda: Intel BayTrail support, ALC5505 DSP support
   - es1968: MediaForte M56VAP support
   - usb-audio: Improved support for Yamaha/Roland devices
   - usb-audio: M2Tech hiFace, Audio Advantage Micro II support
   - hdspm: wordclock fixes
   - ASoC: Pending fixes for WM8962
   - ASoC: Cleanups and fixes for Blackfin, SGTL5000 and UX500
   - ASoC: Generalisation of the Bluetooth and HDMI stub drivers
   - ASoC: SSM2518 and RT5640 codec drivers.
   - ASoC: Tegra CPUs with RT5640 machine driver
   - ASoC: AC'97 refactoring bug fixes
   - ASoC: ADAU1701 driver fixes
   - Clean up of *_set_drvdata() in a wide range of drivers"

* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (284 commits)
  ALSA: vmaster: Fix the regression of missing vmaster hook call
  ALSA: hda - Add Dell SSID to support Headset Mic recording
  ASoC: adau1701: remove control_data assignment
  ASoC: adau1701: more direct regmap usage
  ASoC: ac97: fixup multi-platform AC'97 module build failure
  ASoC: pxa2xx: fixup multi-platform AC'97 build failures
  ASoC: tegra20-ac97: Remove unused variable
  ASoC: tegra20-ac97: Remove duplicate error message
  ALSA: usb-audio: Add Audio Advantage Micro II
  ASoC: tas5086: fix Mid-Z implementation
  ASoC: tas5086: fix TAS5086_CLOCK_CONTROL register size
  ALSA: Replace the magic number 44 with const
  ALSA: hda - Fix the max length of control name in generic parser
  ALSA: hda - Guess what, it's two more Dell headset mic quirks
  ALSA: hda - Yet another Dell headset mic quirk
  ALSA: hda - Add support for ALC5505 DSP power-save mode
  ASoC: mfld: Remove unused variable
  ALSA: usb-audio: add quirks for Roland QUAD/OCTO-CAPTURE
  ALSA: usb-audio: claim autodetected PCM interfaces all at once
  ALSA: usb-audio: remove superfluous Roland quirks
  ...

Pull libata updates from Tejun Heo:
 "Overview of changes:

   - The rest of maintainer email address updates.

   - Some core updates - more robust default behavior for port
     multipliers, better error reporting for SG_IO commands, and a way
     to better work around now ancient and probably pretty rare PATA ->
     SATA bridges with ATAPI devices.

   - sata_rcar stabilization.

   - Some hardware PCI ID additions and one-off low level driver
     updates."

* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
  AHCI: use ATA_BUSY
  libata-zpodd: must use ata_tf_init()
  ahci: AHCI-mode SATA patch for Intel Coleto Creek DeviceIDs
  ata_piix: IDE-mode SATA patch for Intel Coleto Creek DeviceIDs
  libata: cleanup SAT error translation
  ahci: sata: add support for exynos5440 sata
  libata: skip SRST for all SIMG [34]7x port-multipliers
  ahci: remove pmp link online check in FBS EH
  sata highbank: add bit-banged SGPIO driver support
  ahci: make ahci_transmit_led_message into a function pointer
  sata_rcar: fix compilation warning in sata_rcar_thaw()
  sata_highbank: increase retry count but shorten duration for Calxeda controller
  ata: use pci_get_drvdata()
  ipr: qc_fill_rtf() method should not store alternate status register
  sata_rcar: add 'base' local variable to some functions
  sata_rcar: correct 'sata_rcar_sht'
  sata_rcar: kill superfluous code in sata_rcar_bmdma_fill_sg()
  libata: do not limit R-Car SATA driver to shmobile
  ata: use platform_{get,set}_drvdata()
  AHCI: Make distinct names for ports in /proc/interrupts
  ...

Merge first patch-bomb from Andrew Morton:
 - various misc bits
 - I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
   distracted.  There has been quite a bit of activity.
 - About half the MM queue
 - Some backlight bits
 - Various lib/ updates
 - checkpatch updates
 - zillions more little rtc patches
 - ptrace
 - signals
 - exec
 - procfs
 - rapidio
 - nbd
 - aoe
 - pps
 - memstick
 - tools/testing/selftests updates

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
  tools/testing/selftests: don't assume the x bit is set on scripts
  selftests: add .gitignore for kcmp
  selftests: fix clean target in kcmp Makefile
  selftests: add .gitignore for vm
  selftests: add hugetlbfstest
  self-test: fix make clean
  selftests: exit 1 on failure
  kernel/resource.c: remove the unneeded assignment in function __find_resource
  aio: fix wrong comment in aio_complete()
  drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
  drivers/memstick/host/r592.c: convert to module_pci_driver
  drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
  pps-gpio: add device-tree binding and support
  drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
  drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
  drivers/parport/share.c: use kzalloc
  Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
  aoe: update internal version number to v83
  aoe: update copyright date
  aoe: perform I/O completions in parallel
  ...

Pull PCI changes from Bjorn Helgaas:
 "PCI device hotplug
    - Add pci_alloc_dev() interface (Gu Zheng)
    - Add pci_bus_get()/put() for reference counting (Jiang Liu)
    - Fix SR-IOV reference count issues (Jiang Liu)
    - Remove unused acpi_pci_roots list (Jiang Liu)

  MSI
    - Conserve interrupt resources on x86 (Alexander Gordeev)

  AER
    - Force fatal severity when component has been reset (Betty Dall)
    - Reset link below Root Port as well as Downstream Port (Betty Dall)
    - Fix "Firmware first" flag setting (Bjorn Helgaas)
    - Don't parse HEST for non-PCIe devices (Bjorn Helgaas)

  ASPM
    - Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)

  Miscellaneous
    - Add CircuitCo PCI IDs (Darren Hart)
    - Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
    - Work around Ivytown NTB BAR size issue (Jon Mason)
    - Detect invalid initial BAR values (Kevin Hao)
    - Add pcibios_release_device() (Sebastian Ott)
    - Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)"

* tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
  MAINTAINERS: Add ACPI folks for ACPI-related things under drivers/pci
  PCI: Add CircuitCo vendor ID and subsystem ID
  PCI: Use pdev->pm_cap instead of pci_find_capability(..,PCI_CAP_ID_PM)
  PCI: Return early on allocation failures to unindent mainline code
  PCI: Simplify IOV implementation and fix reference count races
  PCI: Drop redundant setting of bus->is_added in virtfn_add_bus()
  unicore32/PCI: Remove redundant call of pci_bus_add_devices()
  m68k/PCI: Remove redundant call of pci_bus_add_devices()
  PCI / ACPI / PM: Use correct power state strings in messages
  PCI: Fix comment typo for pcie_pme_remove()
  PCI: Rename pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
  PCI: Fix refcount issue in pci_create_root_bus() error recovery path
  ia64/PCI: Clean up pci_scan_root_bus() usage
  PCI/AER: Reset link for devices below Root Port or Downstream Port
  ACPI / APEI: Force fatal AER severity when component has been reset
  PCI/AER: Remove "extern" from function declarations
  PCI/AER: Move AER severity defines to aer.h
  PCI/AER: Set dev->__aer_firmware_first only for matching devices
  PCI/AER: Factor out HEST device type matching
  PCI/AER: Don't parse HEST table for non-PCIe devices
  ...

The x bit can easily get lost (patch(1) loses it, for example).
Reported-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As the confusing naming indicates, this test has some overlap with
pre-existing tests.  Would be nice to merge them eventually.  But since it
is only test code, cleanliness is much less important than mere existence.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

thuge-gen was forgotten.  Fix it by removing the duplication, so we don't
get too many repeats.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In case this ever gets scripted, it should return 0 on success and 1 on
failure.  Parsing the output should be left to meatbags.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This line was introduced by fcb11918 ("resources: add arch hook for
preventing allocation in reserved areas").  But the struct tmp was already
assigned to *new in the above line, so this seems superfluous.  Just
remove it.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ctx->ctx_lock should be ctx->completion_lock.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>