- 18 Jan, 2010 33 commits
-
-
Giridhar Malavali authored
[jejb: fixed printk casting issues] Signed-off-by:
Sarang Radke <sarang.radke@qlogic.com> Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
Joe Carnuccio authored
qla2xxx: EEH added call to pci_restore_state. qla2xxx: EEH added delay in slot reset routine. qla2xxx: EEH moved call to pci_save_state(), see (1). qla2xxx: EEH additional changes for RHEL5.5. qla2xxx: EEH added function call, removed function call, see (2). (1) In qla2xxx_probe_one the call to pci_save_state() has been moved to after the call to qla2xxx_request_irqs(). (2) Add call to pci_disable_pcie_error_reporting() in remove_one. Delete call to pci_cleanup_aer_uncorrect_error_status() in pci_resume. Signed-off-by: -
Jayamohan Kallickal authored
This patch enables TEXT Request / Response for the driver Signed-off-by:
Jayamohan Kallickal <jayamohank@serverengines.com> Signed-off-by:
-
Jayamohan Kallickal authored
This patch fixes can_queue being uninitiallized since it was done before beiscsi_get_params was called. Thanks to Mike Christie for identifying this Signed-off-by:
-
Jayamohan Kallickal authored
This fixes a situation where the sessions were being killed whenever LinkUP is notified rather than LinkDown Signed-off-by:
-
Jayamohan Kallickal authored
This patches enables async mode for mcc rings so that multiple requests can be queued. Signed-off-by:
-
Jayamohan Kallickal authored
This patch removes the endianess change that was wrongly added for data_count Signed-off-by:
-
Jayamohan Kallickal authored
This patch decides whether ack based completion is required or not Signed-off-by:
-
Jayamohan Kallickal authored
This patch enables use of opcode that is passed in Signed-off-by:
-
Jayamohan Kallickal authored
This patch moves pci_set_drvdata to inside beiscsi_hba_alloc Signed-off-by:
-
Jayamohan Kallickal authored
This patch adds opcodes in thecompletion path that were missed out earlier Signed-off-by:
-
Jayamohan Kallickal authored
This patch will link the current allocated wrb with the next wrb that will be allocated. This is a requirement from the chip. Signed-off-by:
-
Jayamohan Kallickal authored
We need to hold on to ep resources untill invalidate and close connection are completed Signed-off-by:
-
Jayamohan Kallickal authored
This patch enablesi be2iscsi to use the start number and number of cids/icd provided by FW rather than hard coded values. Signed-off-by:
-
Dave Jones authored
converted using this script.. perl -p -i -e 's|ulong32|u32|g' drivers/scsi/gdth* perl -p -i -e 's|ulong64|u64|g' drivers/scsi/gdth* perl -p -i -e 's|ushort|u16|g' drivers/scsi/gdth* perl -p -i -e 's|unchar|u8|g' drivers/scsi/gdth* perl -p -i -e 's|ulong|unsigned long|g' drivers/scsi/gdth* perl -p -i -e 's|PACKED|__attribute__((packed))|g' drivers/scsi/gdth* sha1sum of the generated code was identical before and after. Signed-off-by:
Dave Jones <davej@redhat.com> Signed-off-by:
-
Douglas Gilbert authored
Further to the lsml thread titled: "does scsi_io_completion need to dump sense data for ata pass through (ck_cond = 1) ?" This is a patch to skip logging when the sense data is associated with a SENSE_KEY of "RECOVERED_ERROR" and the additional sense code is "ATA PASS-THROUGH INFORMATION AVAILABLE". This only occurs with the SAT ATA PASS-THROUGH commands when CK_COND=1 (in the cdb). It indicates that the sense data contains ATA registers. Smartmontools uses such commands on ATA disks connected via SAT. Periodic checks such as those done by smartd cause nuisance entries into logs that are: - neither errors nor warnings - pointless unless the cdb that caused them are also logged Signed-off-by:Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Dan Carpenter authored
The check on MAX_SCSI_TAR should be >= instead of > or we could go past the end of the array. Joe Eykholt aslo correctly points out that the check on MAX_LUN should be >= as well. That matches with how it is used in the rest of the file. Signed-off-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
-
Jiri Slaby authored
Stanse found that c3cn is poked many times around in cxgb3i_conn_pdu_ready, there is no need to check if it is NULL. Remove the test. Signed-off-by:
Jiri Slaby <jirislaby@gmail.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Acked-by:
Karen Xie <kxie@chelsio.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Julia Lawall authored
Use kzalloc rather than kcalloc(1,...) The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ @@ - kcalloc(1, + kzalloc( ...) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Acked-by:
Jack Wang <jack_wang@usish.com> Signed-off-by:
-
Kashyap, Desai authored
Version upgrade to 3.04.14. Signed-off-by:
Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by:
-
Kashyap, Desai authored
Modified the function type check to verify it is not MPI_FUNCTION_RAID_SCSI_IO_PASSTHROUGH or MPI_FUNCTION_SCSI_IO_REQUEST. Signed-off-by:
-
Kashyap, Desai authored
Add support to set the sdev state to SDEV_BLOCK during device removal to stop IOs comming to the deleting driver immediately. Signed-off-by:
-
Kashyap, Desai authored
Added new function mptsas_exp_manufacture_info, which will obtain the REPORT_MANUFACTURING, and fill the details into the sas_expander_device object when the expander port is created. Signed-off-by:
-
Kashyap, Desai authored
There is a 'ioprio' field in the BIO and the Request structure. check this priority field and set MPI_SCSIIO_CONTROL_HEADOFQ to pass down I/O priority. An enhancement to the LSI Disk Array Controller firmware is being developed to look at the Head Of Queue bit to allow I/Os with the HOQ bit set to be processed before I/Os which do not have the HOQ bit set. In order to set the HOQ bit, the mpt fusion driver needs to look at the 'ioprio' field in the request structure associated with the scsi command. Signed-off-by:
-
Finn Thain authored
The mac_esp PIO algorithm no longer works in 2.6.31 and crashes my Centris 660av. So here's a better one. Also, force async with esp_set_offset() rather than esp_slave_configure(). One of the SCSI drives I tested still doesn't like the PIO mode and fails with "esp: esp0: Reconnect IRQ2 timeout" (the same drive works fine in PDMA mode). This failure happens when esp_reconnect_with_tag() tries to read in two tag bytes but the chip only provides one (0x20). I don't know what causes this. I decided not to waste any more time trying to fix it because the best solution is to rip out the PIO mode altogether and use the DMA engine. Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
-
Hannes Reinecke authored
Currently dev_loss_tmo is capped by SCSI_DEVICE_BLOCK_MAX_TIMEOUT. This causes problem with multipathing when the 'no_path_retry' setting exceeds the dev_loss_tmo setting, as then the system might run into a deadlock when all paths have been removed temporarily for longer than dev_loss_tmo. The principal reasons for the capping has been that we should not allow a remote port to remain in status 'blocked' indefinitely, so the capping is there to ensure that the port status is being reset eventually. However, the fast_io_fail_tmo will also move the remote port out of the 'blocked' state, so for any HBA driver implementing both the capping should really be on the fast_io_fail_tmo, and not on the dev_loss_tmo. This patch implements just that, ie the fast_io_fail_tmo is capped to SCSI_DEVICE_BLOCK_TIMEOUT and the capping is removed from dev_loss_tmo when fast_io_fail_tmo is set. This allows us to synchronize the dev_loss_tmo setting to the 'no_path_retry' setting from multipathing thus avoiding the deadlock. Signed-off-by:
Hannes Reinecke <hare@suse.de> Acked-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
Erik Ekman authored
Fixes the following warning: drivers/message/fusion/mptbase.c:129: warning: 'mpt_proc_root_dir' defined but not used also moves it from public data section since it is static. Signed-off-by:
Erik Ekman <erik@kryo.se> Acked-by:
-
Roel Kluin authored
Allows i == IM_MAX_HOSTS, which is out of range. Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
-
Roel Kluin authored
This allows i == MAX_INT_PARAM, which is out of range for ints[] Signed-off-by:
-
Roel Kluin authored
Allows i == MAX_INT_PARAM, which is out of range. Signed-off-by:
-
Bart Van Assche authored
Signed-off-by:
Bart Van Assche <bart.vanassche@gmail.com> Acked-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Bart Van Assche authored
Fixed a typo in libsrp.c: replaced two occurrences of 'RDAM' by 'RDMA'. Signed-off-by:
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by:
-
James Bottomley authored
The best way to fix this is to eliminate the intenal kmalloc() and make the caller allocate the required amount of storage. Signed-off-by:
-
- 17 Jan, 2010 7 commits
-
-
Hannes Reinecke authored
When removing several devices aic79xx will occasionally Oops in ahd_handle_nonpkt_busfree during rescan. Looking at the code I found that we're indeed not checking if the scb in question is NULL. So check for it before accessing it. Signed-off-by:
-
Swen Schillig authored
The hardware used with zfcp provides a timer for CT and ELS requests instead of an abort capability for these commands. To correctly handle the FC BSG timeouts, pass the timeout from the BSG requests to the hardware. Signed-off-by:
Swen Schillig <swen@vnet.ibm.com> Signed-off-by:
-
Swen Schillig authored
Introduce a zfcp callback for timeouts triggered from FC BSG. With zfcp, the underlying hardware cannot abort CT or ELS requests, so there is nothing to do when the block layer timeout expires. To avoid interference with the block layer timeout, simply indicate that the block layer timer should be reset. The timer running in the hardware for the pending CT or ELS request will return the request when it expires. Signed-off-by:
Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by:
-
Swen Schillig authored
The hardware used with zfcp cannot abort a currently pending CT or ELS request. Therefore we need the option to postpone the timeout triggered request abort within the fc layer, since there is nothing zfcp can do to stop the request at this point. Cc: James Smart <James.Smart@emulex.com> Signed-off-by:
-
Heiko Carstens authored
Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
Christof Schmitt authored
Advance the correct pointer when inserting the linebreak for the HBA trace. It was missing in the output since the pointer to the output buffer was never advanced, and the linebreak character was overwritten later. Reviewed-by:
-
Christof Schmitt authored
The patch "zfcp: Simplify handling of ct and els requests" accidentally removed the call to zfcp_fc_wka_port_put for FC CT BSG requests, thus not issuing a "close" request for the WKA ports. Introduce a CT specific handler to first call zfcp_fc_wka_port_put and then continue with the generic handler when returning from FC CT BSG requests. Reviewed-by:
-
