- 11 Apr, 2013 2 commits
-
-
Vikas Chaudhary authored
Issue: If flash read for FLT fails, we are assigning wrong default address for CHAP table in FLT, which will cause CHAP table read/write to wrong address. Fix: Assign correct default CHAP table address to FLT. Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Vikas Chaudhary authored
Signed-off-by:
-
- 10 Apr, 2013 11 commits
-
-
Mahesh Rajashekhara authored
This patch adds dual flash firmware support for Series 7 and above controllers. [thenzl: used ssleep(10) instead udelay] Signed-off-by:
Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
-
Wei Yongjun authored
The variable 'data' is initialized but never used otherwise, so remove the unused variable. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by:
Naresh Kumar Inna <naresh@chelsio.com> Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Tej Parkash authored
Issue: Request queue count holds the information about free space in request queue which has to be manipulated based on request in and out pointer. But in driver response path, this count was incremented unconditionally, which could move req_in pointer beyond req_out pointer. This scenario leads fw hang during IO. Solution: Request queue count manipulation has to be done in IO path only, keeping req_in and req_out pointer two IOCB count away Signed-off-by:
Tej Parkash <tej.parkash@qlogic.com> Signed-off-by:
Shyam Sundar <shyam.sundar@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
Move "Incorrect function ID" print message in case INTX interrupt from DEBUG2 to DEBUG7. This will avoid floods of this message if DEBUG2 is enabled. Signed-off-by:
-
Vikas Chaudhary authored
Use function int_to_scsilun() in qla4xxx_reset_lun() to convert integer value comming from scsi_transport to scsi LUN address format. Signed-off-by:
-
Vikas Chaudhary authored
In case of firmware hung we need to call "mailbox_premature_completion" to complete any pending mbox command as firmware is not alive. Signed-off-by:
-
Vikas Chaudhary authored
For ISP83XX set graceful reset bit in IDC_DRV_CTRL if reset is issued by application Signed-off-by:
-
Vikas Chaudhary authored
Issue: ISP83XX check is missing in function get_fw_boot_info() because of this qla4xxx will not export boot target to sysfs and iscsistart cannot issue login to boot target. Fix: Added check for ISP83XX in function get_fw_boot_info() Signed-off-by:
-
Manish Dusane authored
Problem Description: Disabling pause frames might cause hardware wedging needing a power cycle. This might happen if the Eport is not initialized and is in reset. Solution: Before disabling pause frames ensure that eport is out of reset. Signed-off-by:
Manish Dusane <manish.dusane@qlogic.com> Signed-off-by:
-
Mike Christie authored
For the stpg_endio path we are not evaluating the sense. The bug is that 1. The error value is set to -EIO when there is sense, so we hit the first error check and always return SCSI_DH_IO. 2. h->senselen is set to zero in submit_stpg. It is not later set to req->sense_len like in the synchrounous exection paths, so we must check the req->sense_len field. Signed-off-by:
-
- 09 Apr, 2013 12 commits
-
-
Jack Wang authored
update mail address with my private gmail address for pm8001 driver Signed-off-by:
Jack Wang <jack_wang@usish.com> Signed-off-by:
-
James Smart authored
Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
The service parameters for the VPI/RPIs were incorrect, resulting in lower utilization Signed-off-by:
-
James Smart authored
Fixed NMI watch dog panic's when resetting the hba. Signed-off-by:
-
- 06 Apr, 2013 14 commits
-
-
Lukasz Dorau authored
If a result of the SMP discover function is PHY VACANT, the content of discover response structure (dr) is not valid. It sometimes happens that dr->attached_sas_addr can contain even SAS address of other phy. In such case an invalid phy is created, what causes NULL pointer dereference during destruction of expander's phys. So if a result of SMP function is PHY VACANT, the content of discover response structure (dr) must not be copied to phy structure. This patch fixes the following bug: BUG: unable to handle kernel NULL pointer dereference at 0000000000000030 IP: [<ffffffff811c9002>] sysfs_find_dirent+0x12/0x90 Call Trace: [<ffffffff811c95f5>] sysfs_get_dirent+0x35/0x80 [<ffffffff811cb55e>] sysfs_unmerge_group+0x1e/0xb0 [<ffffffff813329f4>] dpm_sysfs_remove+0x24/0x90 [<ffffffff8132b0f4>] device_del+0x44/0x1d0 [<ffffffffa016fc59>] sas_rphy_delete+0x9/0x20 [scsi_transport_sas] [<ffffffffa01a16f6>] sas_destruct_devices+0xe6/0x110 [libsas] [<ffffffff8107ac7c>] process_one_work+0x16c/0x350 [<ffffffff8107d84a>] worker_thread+0x17a/0x410 [<ffffffff81081b76>] kthread+0x96/0xa0 [<ffffffff81464944>] kernel_thread_helper+0x4/0x10 Signed-off-by:
Lukasz Dorau <lukasz.dorau@intel.com> Signed-off-by:
Pawel Baldysiak <pawel.baldysiak@intel.com> Reviewed-by:
Maciej Patelczyk <maciej.patelczyk@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Brian King authored
No locks should be held when calling scsi_adjust_queue_depth so drop the lock in slave_configure prior to calling it. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Acked-by:
Robert Jennings <rcj@linux.vnet.ibm.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Arun Easi authored
System crashes, in initiator mode operation, with qla2xxx_copy_atioqueues() in stack trace when firmware dump is attempted. Check for atio_q_length alone does not indicate if atio_ring is allocated, make explicit check of atio_ring to avoid the crash. Applicable to ISP24xx, ISP25xx, ISP81xx & ISP83xx line of HBAs. Signed-off-by:
Arun Easi <arun.easi@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
The original patch was not covering all the adapters and firmwares. This commit reverts 3a11711a. Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
-
wenxiong@linux.vnet.ibm.com authored
Reinitialize resource queue prior to freeing resource entries to ensure they are not referenced. This fixes an issue with target_destoy accessing memory after it was freed. Signed-off-by:
Wen Xiong <wenxiong@linux.vnet.ibm.com> Acked-by:
-
Kleber Sacilotto de Souza authored
The abort command issued by ipr_cancel_op() is being added to the wrong HRRQ free queue after the command returns. Fix it by using the HRRQ pointer in the ipr command struct itself. Signed-off-by:
Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by:
-
Joe Lawrence authored
This patch fixes a reference count bug in the SCSI tape driver which can be reproduced with the following: * Boot with slub_debug=FZPU, tape drive attached * echo 1 > /sys/devices/... tape device pci path .../remove * Wait for device removal * echo 1 > /sys/kernel/slab/blkdev_queue/validate * Slub debug complains about corrupted poison pattern In commit 523e1d39 (block: make gendisk hold a reference to its queue) add_disk() and disk_release() were modified to get/put an additional reference on a disk queue to fix a reference counting discrepency between bdev release and SCSI device removal. The ST driver never calls add_disk(), so this commit introduced an extra kref put when the ST driver frees its struct gendisk. Attempts were made to fix this bug at the block level [1] but later abandoned due to floppy driver issues [2]. [1] https://lkml.org/lkml/2012/8/27/354 [2] https://lkml.org/lkml/2012/9/22/113Signed-off-by:
Joe Lawrence <joe.lawrence@stratus.com> Tested-by:
Ewan D. Milne <emilne@redhat.com> Acked-by:
Kai Mäkisara <Kai.Makisara@kolumbus.fi> Signed-off-by:
-
John Gong authored
In fact the disc_resp buffer will be overwrite by smp response, so we never found this typo, correct it by using the right one. Signed-off-by:
John Gong <john_gong@usish.com> Signed-off-by:
-
wenxiong@linux.vnet.ibm.com authored
Loading ipr modules failed(-22) with msi-x enabled adapter. In ipr_test_msi(), We need to pass the first vector of msix vectors instead of using pdev->irq to request_irq() when adapter enables msix feature. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dmLinus Torvalds authored
Pull device-mapper fixes from Alasdair Kergon: "A pair of patches to fix the writethrough mode of the device-mapper cache target when the device being cached is not itself wrapped with device-mapper." * tag 'dm-3.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: dm cache: reduce bio front_pad size in writeback mode dm cache: fix writes to cache device in writethrough mode
-
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pciLinus Torvalds authored
Pull PCI fixes from Bjorn Helgaas: "PCI updates for v3.9: ASPM Revert "PCI/ACPI: Request _OSC control before scanning PCI root bus" kexec PCI: Don't try to disable Bus Master on disconnected PCI devices Platform ROM images PCI: Add PCI ROM helper for platform-provided ROM images nouveau: Attempt to use platform-provided ROM image radeon: Attempt to use platform-provided ROM image Hotplug PCI/ACPI: Always resume devices on ACPI wakeup notifications PCI/PM: Disable runtime PM of PCIe ports EISA EISA/PCI: Fix bus res reference EISA/PCI: Init EISA early, before PNP" * tag 'pci-v3.9-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI/PM: Disable runtime PM of PCIe ports PCI/ACPI: Always resume devices on ACPI wakeup notifications PCI: Don't try to disable Bus Master on disconnected PCI devices Revert "PCI/ACPI: Request _OSC control before scanning PCI root bus" radeon: Attempt to use platform-provided ROM image nouveau: Attempt to use platform-provided ROM image EISA/PCI: Init EISA early, before PNP EISA/PCI: Fix bus res reference PCI: Add PCI ROM helper for platform-provided ROM images
-
- 05 Apr, 2013 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix erroneous sock_orphan() leading to crashes and double kfree_skb() in NFC protocol. From Thierry Escande and Samuel Ortiz. 2) Fix use after free in remain-on-channel mac80211 code, from Johannes Berg. 3) nf_reset() needs to reset the NF tracing cookie, otherwise we can leak it from one namespace into another. Fix from Gao Feng and Patrick McHardy. 4) Fix overflow in channel scanning array of mwifiex driver, from Stone Piao. 5) Fix loss of link after suspend/shutdown in r8169, from Hayes Wang. 6) Synchronization of unicast address lists to the undelying device doesn't work because whether to sync is maintained as a boolean rather than a true count. Fix from Vlad Yasevich. 7) Fix corruption of TSO packets in atl1e by limiting the segmented packet length. From Hannes Frederic Sowa. 8) Revert bogus AF_UNIX credential passing change and fix the coalescing issue properly, from Eric W Biederman. 9) Changes of ipv4 address lifetime settings needs to generate a notification, from Jiri Pirko. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits) netfilter: don't reset nf_trace in nf_reset() net: ipv4: notify when address lifetime changes ixgbe: fix registration order of driver and DCA nofitication af_unix: If we don't care about credentials coallesce all messages Revert "af_unix: dont send SCM_CREDENTIAL when dest socket is NULL" bonding: remove sysfs before removing devices atl1e: limit gso segment size to prevent generation of wrong ip length fields net: count hw_addr syncs so that unsync works properly. r8169: fix auto speed down issue netfilter: ip6t_NPT: Fix translation for non-multiple of 32 prefix lengths mwifiex: limit channel number not to overflow memory NFC: microread: Fix build failure due to a new MEI bus API iwlwifi: dvm: fix the passive-no-RX workaround netfilter: nf_conntrack: fix error return code NFC: llcp: Keep the connected socket parent pointer alive mac80211: fix idle handling sequence netfilter: nfnetlink_acct: return -EINVAL if object name is empty netfilter: nfnetlink_queue: fix error return code in nfnetlink_queue_init() netfilter: reset nf_trace in nf_reset mac80211: fix remain-on-channel cancel crash ...
-
