When the PXS8 and PHS8 devices show up with PID 0x0053 they will expose both a
QMI port and a WWAN interface.

CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

linux-can-fixes-for-3.14-20140212

Marc Kleine-Budde says:

====================
this is a pull request with one patch for net/master, for the current release
cycle. Olivier Sobrie noticed and fixed that the kvaser_usb driver doesn't
check the number of channels value from the hardware, which may result in
writing over the bounds of an array in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Warning log:
xilinx_axienet_main.c: In function 'axienet_start_xmit_done':
xilinx_axienet_main.c:617:16: warning: operation on 'lp->tx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_start_xmit':
xilinx_axienet_main.c:703:18: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c:719:17: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_recv':
xilinx_axienet_main.c:792:16: warning: operation on 'lp->rx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_of_probe':
xilinx_axienet_main.c:1501:21: warning: unused variable 'rc' [-Wunused-variable]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing header to fix compilation error.
drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1575:22:
 error: undefined identifier 'irq_of_parse_and_map'
drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1576:22:
 error: undefined identifier 'irq_of_parse_and_map'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner reported problems when the forwarding link path
has a lower mtu than the incoming one if the inbound interface supports GRO.

Given:
Host <mtu1500> R1 <mtu1200> R2

Host sends tcp stream which is routed via R1 and R2.  R1 performs GRO.

In this case, the kernel will fail to send ICMP fragmentation needed
messages (or pkt too big for ipv6), as GSO packets currently bypass dstmtu
checks in forward path. Instead, Linux tries to send out packets exceeding
the mtu.

When locking route MTU on Host (i.e., no ipv4 DF bit set), R1 does
not fragment the packets when forwarding, and again tries to send out
packets exceeding R1-R2 link mtu.

This alters the forwarding dstmtu checks to take the individual gso
segment lengths into account.

For ipv6, we send out pkt too big error for gso if the individual
segments are too big.

For ipv4, we either send icmp fragmentation needed, or, if the DF bit
is not set, perform software segmentation and let the output path
create fragments when the packet is leaving the machine.
It is not 100% correct as the error message will contain the headers of
the GRO skb instead of the original/segmented one, but it seems to
work fine in my (limited) tests.

Eric Dumazet suggested to simply shrink mss via ->gso_size to avoid
sofware segmentation.

However it turns out that skb_segment() assumes skb nr_frags is related
to mss size so we would BUG there.  I don't want to mess with it considering
Herbert and Eric disagree on what the correct behavior should be.

Hannes Frederic Sowa notes that when we would shrink gso_size
skb_segment would then also need to deal with the case where
SKB_MAX_FRAGS would be exceeded.

This uses sofware segmentation in the forward path when we hit ipv4
non-DF packets and the outgoing link mtu is too small.  Its not perfect,
but given the lack of bug reports wrt. GRO fwd being broken this is a
rare case anyway.  Also its not like this could not be improved later
once the dust settles.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Will be used by upcoming ipv4 forward path change that needs to
determine feature mask using skb->dst->dev instead of skb->dev.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bonding driver take write locks and spin locks that are shared
by the tx path in enslave processing and notification processing,
If the netconsole is in use, the bonding can call printk which puts
us in the netpoll tx path, if the netconsole is attached to the bonding
driver, result in deadlock.

So add protection for these place, by checking the netpoll_block_tx
state, we can defer the sending of the netconsole frames until a later
time using the retransmit feature of netpoll_send_skb that is triggered
on the return code NETDEV_TX_BUSY.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the commit 0e245dba
("drivers/net: delete the 3Com 3c505/3c507 intel i825xx support")
we clobbered the 3c505 driver (over a year ago) along with other
abandoned ISA drivers.

However, this orphaned README file escaped detection at that
time, and has lived on until today. Get rid of it now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Here, when the net is init_net, we needn't to kmemdup the ctl_table
again. So add a check for net. Also we can save some memory.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As commit 3c68198e("sctp: Make hmac algorithm selection for
 cookie generation dynamic"), we miss the .data initialization.
If we don't use the net_namespace, the problem that parts of the
sysctl configuration won't be isolation and won't occur.

In sctp_sysctl_net_register(), we register the sysctl for each
net, in the for(), we use the 'table[i].data' as check condition, so
when the 'i' is the index of sctp_hmac_alg, the data is NULL, then
break. So add the .data initialization.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I saw the following BUG when ->newlink() fails in rtnl_newlink():

[   40.240058] kernel BUG at net/core/dev.c:6438!

this is due to free_netdev() is not supposed to be called before
netdev is completely unregistered, therefore it is not correct
to call free_netdev() here, at least for ops->newlink!=NULL case,
many drivers call it in ->destructor so that rtnl_unlock() will
take care of it, we probably don't need to do anything here.

Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl_newlink() doesn't unregister it for us on failure.

Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a packet received on a link is out-of-sequence, it will be
placed on a deferred queue and later reinserted in the receive
path once the preceding packets have been processed. The problem
with this is that it will be subject to the buffer adjustment from
link_recv_buf_validate twice. The second adjustment for 20 bytes
header space will corrupt the packet.

We solve this by tagging the deferred packets and bail out from
receive buffer validation for packets that have already been
subjected to this.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.

This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netlink kind (and iproute2 type option) is actually called
'macvtap', not 'macvlan'.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is needed to check the number of channels returned by the HW because it
cannot be greater than MAX_NET_DEVICES otherwise it will crash.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull microblaze fixes from Michal Simek:
 - Fix two compilation issues - HZ, readq/writeq
 - Fix stack protection support

* tag 'microblaze-3.14-rc3' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix a typo when disabling stack protection
  microblaze: Define readq and writeq IO helper function
  microblaze: Fix missing HZ macro

Pull s390 bugfixes from Martin Schwidefsky:
 "A collection a bug fixes.  Most of them are minor but two of them are
  more severe.  The linkage stack bug can be used by user space to force
  an oops, with panic_on_oops this is a denial-of-service.  And the dump
  memory detection issue can cause incomplete memory dumps"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/cio: improve cio_commit_config
  s390: fix kernel crash due to linkage stack instructions
  s390/dump: Fix dump memory detection
  s390/appldata: restore missing init_virt_timer()
  s390/qdio: correct program-controlled interruption checking
  s390/qdio: for_each macro correctness

Pull networking updates from David Miller:

 1) Fix flexcan build on big endian, from Arnd Bergmann

 2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese

 3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
    non-sleepable contexts.  From Or Gerlitz

 4) vxlan_gro_receive() does not iterate over all possible flows
    properly, fix also from Or Gerlitz

 5) CAN core doesn't use a proper SKB destructor when it hooks up
    sockets to SKBs.  Fix from Oliver Hartkopp

 6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
    Eric Dumazet

 7) Fix address family assignment in IPVS, from Michal Kubecek

 8) Fix ath9k build on ARM, from Sujith Manoharan

 9) Make sure fail_over_mac only applies for the correct bonding modes,
    from Ding Tianhong

10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz

11) Handle gigabit features properly in generic PHY code, from Florian
    Fainelli

12) Don't blindly invoke link operations in
    rtnl_link_get_slave_info_data_size, they are optional.  Fix from
    Fernando Luis Vazquez Cao

13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork

14) Handle netlink packet padding properly in openvswitch, from Thomas
    Graf

15) Fix oops when deleting chains in nf_tables, from Patrick McHardy

16) Fix RX stalls in xen-netback driver, from Zoltan Kiss

17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach

18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
    Uytterhoeven

19) tg3_change_mtu() can deadlock, fix from Nithin Sujir

20) Fix regression in setting SCTP local source addresses on accepted
    sockets, caused by some generic ipv6 socket changes.  Fix from
    Matija Glavinic Pecotic

21) IPPROTO_* must be pure defines, otherwise module aliases don't get
    constructed properly.  Fix from Jan Moskyto

22) IPV6 netconsole setup doesn't work properly unless an explicit
    source address is specified, fix from Sabrina Dubroca

23) Use __GFP_NORETRY for high order skb page allocations in
    sock_alloc_send_pskb and skb_page_frag_refill.  From Eric Dumazet

24) Fix a regression added in netconsole over bridging, from Cong Wang

25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
    well with TCP pacing which needs the SRTT to be accurate.  Fix from
    Eric Dumazet

26) Several cases of missing header file includes from Rashika Kheria

27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike

28) TCP Small Queues doesn't handle nonagle properly in some corner
    cases, fix from Eric Dumazet

29) Remove extraneous read_unlock in bond_enslave, whoops.  From Ding
    Tianhong

30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
  6lowpan: fix lockdep splats
  alx: add missing stats_lock spinlock init
  9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
  bonding: remove unwanted bond lock for enslave processing
  USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
  tcp: tsq: fix nonagle handling
  bridge: Prevent possible race condition in br_fdb_change_mac_address
  bridge: Properly check if local fdb entry can be deleted when deleting vlan
  bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
  bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
  bridge: Fix the way to check if a local fdb entry can be deleted
  bridge: Change local fdb entries whenever mac address of bridge device changes
  bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
  bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
  bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
  tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
  net: vxge: Remove unused device pointer
  net: qmi_wwan: add ZTE MF667
  3c59x: Remove unused pointer in vortex_eisa_cleanup()
  net: fix 'ip rule' iif/oif device rename
  ...

When a device ndo_start_xmit() calls again dev_queue_xmit(),
lockdep can complain because dev_queue_xmit() is re-entered and the
spinlocks protecting tx queues share a common lockdep class.

Same issue was fixed for bonding/l2tp/ppp in commits

0daa2303 ("[PATCH] bonding: lockdep annotation")
49ee4920 ("bonding: set qdisc_tx_busylock to avoid LOCKDEP splat")
23d3b8bf ("net: qdisc busylock needs lockdep annotations ")
303c07db ("ppp: set qdisc_tx_busylock to avoid LOCKDEP splat ")
Reported-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix for init time stack trace occuring in
alx_get_stats64 upon start up. Should have been part of
commit adding the spinlock:
f1b6b106 alx: add alx_get_stats64 operation
Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 9p-virtio transport does zero copy on things larger than 1024 bytes
in size. It accomplishes this by returning the physical addresses of
pages to the virtio-pci device. At present, the translation is usually a
bit shift.

That approach produces an invalid page address when we read/write to
vmalloc buffers, such as those used for Linux kernel modules. Any
attempt to load a Linux kernel module from 9p-virtio produces the
following stack.

[<ffffffff814878ce>] p9_virtio_zc_request+0x45e/0x510
[<ffffffff814814ed>] p9_client_zc_rpc.constprop.16+0xfd/0x4f0
[<ffffffff814839dd>] p9_client_read+0x15d/0x240
[<ffffffff811c8440>] v9fs_fid_readn+0x50/0xa0
[<ffffffff811c84a0>] v9fs_file_readn+0x10/0x20
[<ffffffff811c84e7>] v9fs_file_read+0x37/0x70
[<ffffffff8114e3fb>] vfs_read+0x9b/0x160
[<ffffffff81153571>] kernel_read+0x41/0x60
[<ffffffff810c83ab>] copy_module_from_fd.isra.34+0xfb/0x180

Subsequently, QEMU will die printing:

qemu-system-x86_64: virtio: trying to map MMIO memory

This patch enables 9p-virtio to correctly handle this case. This not
only enables us to load Linux kernel modules off virtfs, but also
enables ZFS file-based vdevs on virtfs to be used without killing QEMU.

Special thanks to both Avi Kivity and Alexander Graf for their
interpretation of QEMU backtraces. Without their guidence, tracking down
this bug would have taken much longer. Also, special thanks to Linus
Torvalds for his insightful explanation of why this should use
is_vmalloc_addr() instead of is_vmalloc_or_module_addr():

https://lkml.org/lkml/2014/2/8/272Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bond enslave processing don't hold bond->lock anymore,
so release an unlocked rw lock will cause warning message,
remove the unwanted read_unlock(&bond->lock).

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Liu Junliang <liujunliang_ljl@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge misc fixes from Andrew Morton:
 "A bunch of fixes"

* emailed patches fron Andrew Morton <akpm@linux-foundation.org>:
  ocfs2: check existence of old dentry in ocfs2_link()
  ocfs2: update inode size after zeroing the hole
  ocfs2: fix issue that ocfs2_setattr() does not deal with new_i_size==i_size
  mm/memory-failure.c: move refcount only in !MF_COUNT_INCREASED
  smp.h: fix x86+cpu.c sparse warnings about arch nonboot CPU calls
  mm: fix page leak at nfs_symlink()
  slub: do not assert not having lock in removing freed partial
  gitignore: add all.config
  ocfs2: fix ocfs2_sync_file() if filesystem is readonly
  drivers/edac/edac_mc_sysfs.c: poll timeout cannot be zero
  fs/file.c:fdtable: avoid triggering OOMs from alloc_fdmem
  xen: properly account for _PAGE_NUMA during xen pte translations
  mm/slub.c: list_lock may not be held in some circumstances
  drivers/md/bcache/extents.c: use %zi to format size_t
  vmcore: prevent PT_NOTE p_memsz overflow during header update
  drivers/message/i2o/i2o_config.c: fix deadlock in compat_ioctl(I2OGETIOPS)
  Documentation/: update 00-INDEX files
  checkpatch: fix detection of git repository
  get_maintainer: fix detection of git repository
  drivers/misc/sgi-gru/grukdump.c: unlocking should be conditional in gru_dump_context()

System call linkat first calls user_path_at(), check the existence of
old dentry, and then calls vfs_link()->ocfs2_link() to do the actual
work.  There may exist a race when Node A create a hard link for file
while node B rm it.

         Node A                          Node B
user_path_at()
  ->ocfs2_lookup(),
find old dentry exist
                                rm file, add inode say inodeA
                                to orphan_dir

call ocfs2_link(),create a
hard link for inodeA.

                                rm the link, add inodeA to orphan_dir
                                again

When orphan_scan work start, it calls ocfs2_queue_orphans() to do the
main work.  It first tranverses entrys in orphan_dir, linking all inodes
in this orphan_dir to a list look like this:

	inodeA->inodeB->...->inodeA

When tranvering this list, it will fall into loop, calling iput() again
and again.  And finally trigger BUG_ON(inode->i_state & I_CLEAR).
Signed-off-by: joyce <xuejiufei@huawei.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs-writeback will release the dirty pages without page lock whose offset
are over inode size, the release happens at
block_write_full_page_endio().  If not update, dirty pages in file holes
may be released before flushed to the disk, then file holes will contain
some non-zero data, this will cause sparse file md5sum error.

To reproduce the bug, find a big sparse file with many holes, like vm
image file, its actual size should be bigger than available mem size to
make writeback work more frequently, tar it with -S option, then keep
untar it and check its md5sum again and again until you get a wrong
md5sum.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Younger Liu <younger.liu@huawei.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The issue scenario is as following:

- Create a small file and fallocate a large disk space for a file with
  FALLOC_FL_KEEP_SIZE option.

- ftruncate the file back to the original size again.  but the disk free
  space is not changed back.  This is a real bug that be fixed in this
  patch.

In order to solve the issue above, we modified ocfs2_setattr(), if
attr->ia_size != i_size_read(inode), It calls ocfs2_truncate_file(), and
truncate disk space to attr->ia_size.
Signed-off-by: Younger Liu <younger.liu@huawei.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Tested-by: Jie Liu <jeff.liu@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Sunil Mushran <sunil.mushran@gmail.com>
Reviewed-by: Jensen <shencanquan@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mce-test detected a test failure when injecting error to a thp tail
page.  This is because we take page refcount of the tail page in
madvise_hwpoison() while the fix in commit a3e0f9e4
("mm/memory-failure.c: transfer page count from head page to tail page
after split thp") assumes that we always take refcount on the head page.

When a real memory error happens we take refcount on the head page where
memory_failure() is called without MF_COUNT_INCREASED set, so it seems
to me that testing memory error on thp tail page using madvise makes
little sense.

This patch cancels moving refcount in !MF_COUNT_INCREASED for valid
testing.

[akpm@linux-foundation.org: s/&&/&/]
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: <stable@vger.kernel.org>	[3.9+: a3e0f9e4]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use what we already do for arch_disable_smp_support() to fix these:

  arch/x86/kernel/smpboot.c:1155:6: warning: symbol 'arch_enable_nonboot_cpus_begin' was not declared. Should it be static?
  arch/x86/kernel/smpboot.c:1160:6: warning: symbol 'arch_enable_nonboot_cpus_end' was not declared. Should it be static?
  kernel/cpu.c:512:13: warning: symbol 'arch_enable_nonboot_cpus_begin' was not declared. Should it be static?
  kernel/cpu.c:516:13: warning: symbol 'arch_enable_nonboot_cpus_end' was not declared. Should it be static?
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Changes in commit a0b8cab3 ("mm: remove lru parameter from
__pagevec_lru_add and remove parts of pagevec API") have introduced a
call to add_to_page_cache_lru() which causes a leak in nfs_symlink() as
now the page gets an extra refcount that is not dropped.

Jan Stancek observed and reported the leak effect while running test8
from Connectathon Testsuite.  After several iterations over the test
case, which creates several symlinks on a NFS mountpoint, the test
system was quickly getting into an out-of-memory scenario.

This patch fixes the page leak by dropping that extra refcount
add_to_page_cache_lru() is grabbing.
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: <stable@vger.kernel.org>	[3.11.x+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Vladimir reported the following issue:

Commit c65c1877 ("slub: use lockdep_assert_held") requires
remove_partial() to be called with n->list_lock held, but free_partial()
called from kmem_cache_close() on cache destruction does not follow this
rule, leading to a warning:

  WARNING: CPU: 0 PID: 2787 at mm/slub.c:1536 __kmem_cache_shutdown+0x1b2/0x1f0()
  Modules linked in:
  CPU: 0 PID: 2787 Comm: modprobe Tainted: G        W    3.14.0-rc1-mm1+ #1
  Hardware name:
   0000000000000600 ffff88003ae1dde8 ffffffff816d9583 0000000000000600
   0000000000000000 ffff88003ae1de28 ffffffff8107c107 0000000000000000
   ffff880037ab2b00 ffff88007c240d30 ffffea0001ee5280 ffffea0001ee52a0
  Call Trace:
    __kmem_cache_shutdown+0x1b2/0x1f0
    kmem_cache_destroy+0x43/0xf0
    xfs_destroy_zones+0x103/0x110 [xfs]
    exit_xfs_fs+0x38/0x4e4 [xfs]
    SyS_delete_module+0x19a/0x1f0
    system_call_fastpath+0x16/0x1b

His solution was to add a spinlock in order to quiet lockdep.  Although
there would be no contention to adding the lock, that lock also requires
disabling of interrupts which will have a larger impact on the system.

Instead of adding a spinlock to a location where it is not needed for
lockdep, make a __remove_partial() function that does not test if the
list_lock is held, as no one should have it due to it being freed.

Also added a __add_partial() function that does not do the lock
validation either, as it is not needed for the creation of the cache.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Vladimir Davydov <vdavydov@parallels.com>
Suggested-by: David Rientjes <rientjes@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is used by kbuild to load preset Kconfig options.  We need to
ignore it, otherwise git clean kills it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If filesystem is readonly, there is no need to flush drive's caches or
force any uncommitted transactions.

[akpm@linux-foundation.org: return -EROFS, not 0]
Signed-off-by: Younger Liu <younger.liucn@gmail.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If you do

  echo 0 > /sys/module/edac_core/parameters/edac_mc_poll_msec

the following stack trace is output because the edac module is not
designed to poll with a timeout of zero.

  WARNING: CPU: 12 PID: 0 at lib/list_debug.c:33 __list_add+0xac/0xc0()
  list_add corruption. prev->next should be next (ffff8808291dd1b8), but was           (null). (prev=ffff8808286fe3f8).
  Modules linked in: sg nfsv3 rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache cfg80211 rfkill x86_pkg_temp_thermal coretemp kvm_intel kvm ixgbe e1000e crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt ptp sb_edac iTCO_vendor_support pps_core mdio ipmi_devintf edac_core ioatdma microcode shpchp lpc_ich pcspkr i2c_i801 dca mfd_core ipmi_si wmi ipmi_msghandler nfsd auth_rpcgss nfs_acl lockd sunrpc xfs libcrc32c sd_mod sr_mod cdrom crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt isci i2c_algo_bit drm_kms_helper ttm drm libsas ahci libahci scsi_transport_sas libata i2c_core dm_mirror dm_region_hash dm_log dm_mod
  CPU: 12 PID: 0 Comm: swapper/12 Not tainted 3.13.0+ #1
  Hardware name: Intel Corporation LH Pass ........../SVRBD-ROW_T, BIOS SE5C600.86B.01.08.0003.022620131521 02/26/2013
  Call Trace:
   <IRQ>
    __list_add+0xac/0xc0
    __internal_add_timer+0xab/0x130
    internal_add_timer+0x17/0x40
    mod_timer_pinned+0xca/0x170
    intel_pstate_timer_func+0x28a/0x380
    call_timer_fn+0x36/0x100
    run_timer_softirq+0x1ff/0x2f0
    __do_softirq+0xf5/0x2e0
    irq_exit+0x10d/0x120
    smp_apic_timer_interrupt+0x45/0x60
    apic_timer_interrupt+0x6d/0x80
   <EOI>
    cpuidle_idle_call+0xb9/0x1f0
    arch_cpu_idle+0xe/0x30
    cpu_startup_entry+0x9e/0x240
    start_secondary+0x1e4/0x290

  kernel BUG at kernel/timer.c:1084!
  invalid opcode: 0000 [#1] SMP
  Modules linked in: sg nfsv3 rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache cfg80211 rfkill x86_pkg_temp_thermal coretemp kvm_intel kvm ixgbe e1000e crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt ptp sb_edac iTCO_vendor_support pps_core mdio ipmi_devintf edac_core ioatdma microcode shpchp lpc_ich pcspkr i2c_i801 dca mfd_core ipmi_si wmi ipmi_msghandler nfsd auth_rpcgss nfs_acl lockd sunrpc xfs libcrc32c sd_mod sr_mod cdrom crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt isci i2c_algo_bit drm_kms_helper ttm drm libsas ahci libahci scsi_transport_sas libata i2c_core dm_mirror dm_region_hash dm_log dm_mod
  CPU: 12 PID: 0 Comm: swapper/12 Tainted: G        W    3.13.0+ #1
  Hardware name: Intel Corporation LH Pass ........../SVRBD-ROW_T, BIOS SE5C600.86B.01.08.0003.022620131521 02/26/2013
  Call Trace:
   <IRQ>
    run_timer_softirq+0x245/0x2f0
    __do_softirq+0xf5/0x2e0
    irq_exit+0x10d/0x120
    smp_apic_timer_interrupt+0x45/0x60
    apic_timer_interrupt+0x6d/0x80
   <EOI>
    cpuidle_idle_call+0xb9/0x1f0
    arch_cpu_idle+0xe/0x30
    cpu_startup_entry+0x9e/0x240
    start_secondary+0x1e4/0x290
  RIP   cascade+0x93/0xa0

  WARNING: CPU: 36 PID: 1154 at kernel/workqueue.c:1461 __queue_delayed_work+0xed/0x1a0()
  Modules linked in: sg nfsv3 rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache cfg80211 rfkill x86_pkg_temp_thermal coretemp kvm_intel kvm ixgbe e1000e crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt ptp sb_edac iTCO_vendor_support pps_core mdio ipmi_devintf edac_core ioatdma microcode shpchp lpc_ich pcspkr i2c_i801 dca mfd_core ipmi_si wmi ipmi_msghandler nfsd auth_rpcgss nfs_acl lockd sunrpc xfs libcrc32c sd_mod sr_mod cdrom crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt isci i2c_algo_bit drm_kms_helper ttm drm libsas ahci libahci scsi_transport_sas libata i2c_core dm_mirror dm_region_hash dm_log dm_mod
  CPU: 36 PID: 1154 Comm: kworker/u481:3 Tainted: G        W    3.13.0+ #1
  Hardware name: Intel Corporation LH Pass ........../SVRBD-ROW_T, BIOS SE5C600.86B.01.08.0003.022620131521 02/26/2013
  Workqueue: edac-poller edac_mc_workq_function [edac_core]
  Call Trace:
    dump_stack+0x45/0x56
    warn_slowpath_common+0x7d/0xa0
    warn_slowpath_null+0x1a/0x20
    __queue_delayed_work+0xed/0x1a0
    queue_delayed_work_on+0x27/0x50
    edac_mc_workq_function+0x72/0xa0 [edac_core]
    process_one_work+0x17b/0x460
    worker_thread+0x11b/0x400
    kthread+0xd2/0xf0
    ret_from_fork+0x7c/0xb0

This patch adds a range check in the edac_mc_poll_msec code to check for 0.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Recently due to a spike in connections per second memcached on 3
separate boxes triggered the OOM killer from accept.  At the time the
OOM killer was triggered there was 4GB out of 36GB free in zone 1.  The
problem was that alloc_fdtable was allocating an order 3 page (32KiB) to
hold a bitmap, and there was sufficient fragmentation that the largest
page available was 8KiB.

I find the logic that PAGE_ALLOC_COSTLY_ORDER can't fail pretty dubious
but I do agree that order 3 allocations are very likely to succeed.

There are always pathologies where order > 0 allocations can fail when
there are copious amounts of free memory available.  Using the pigeon
hole principle it is easy to show that it requires 1 page more than 50%
of the pages being free to guarantee an order 1 (8KiB) allocation will
succeed, 1 page more than 75% of the pages being free to guarantee an
order 2 (16KiB) allocation will succeed and 1 page more than 87.5% of
the pages being free to guarantee an order 3 allocate will succeed.

A server churning memory with a lot of small requests and replies like
memcached is a common case that if anything can will skew the odds
against large pages being available.

Therefore let's not give external applications a practical way to kill
linux server applications, and specify __GFP_NORETRY to the kmalloc in
alloc_fdmem.  Unless I am misreading the code and by the time the code
reaches should_alloc_retry in __alloc_pages_slowpath (where
__GFP_NORETRY becomes signification).  We have already tried everything
reasonable to allocate a page and the only thing left to do is wait.  So
not waiting and falling back to vmalloc immediately seems like the
reasonable thing to do even if there wasn't a chance of triggering the
OOM killer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Cong Wang <cwang@twopensource.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Steven Noonan forwarded a users report where they had a problem starting
vsftpd on a Xen paravirtualized guest, with this in dmesg:

  BUG: Bad page map in process vsftpd  pte:8000000493b88165 pmd:e9cc01067
  page:ffffea00124ee200 count:0 mapcount:-1 mapping:     (null) index:0x0
  page flags: 0x2ffc0000000014(referenced|dirty)
  addr:00007f97eea74000 vm_flags:00100071 anon_vma:ffff880e98f80380 mapping:          (null) index:7f97eea74
  CPU: 4 PID: 587 Comm: vsftpd Not tainted 3.12.7-1-ec2 #1
  Call Trace:
    dump_stack+0x45/0x56
    print_bad_pte+0x22e/0x250
    unmap_single_vma+0x583/0x890
    unmap_vmas+0x65/0x90
    exit_mmap+0xc5/0x170
    mmput+0x65/0x100
    do_exit+0x393/0x9e0
    do_group_exit+0xcc/0x140
    SyS_exit_group+0x14/0x20
    system_call_fastpath+0x1a/0x1f
  Disabling lock debugging due to kernel taint
  BUG: Bad rss-counter state mm:ffff880e9ca60580 idx:0 val:-1
  BUG: Bad rss-counter state mm:ffff880e9ca60580 idx:1 val:1

The issue could not be reproduced under an HVM instance with the same
kernel, so it appears to be exclusive to paravirtual Xen guests.  He
bisected the problem to commit 1667918b ("mm: numa: clear numa
hinting information on mprotect") that was also included in 3.12-stable.

The problem was related to how xen translates ptes because it was not
accounting for the _PAGE_NUMA bit.  This patch splits pte_present to add
a pteval_present helper for use by xen so both bare metal and xen use
the same code when checking if a PTE is present.

[mgorman@suse.de: wrote changelog, proposed minor modifications]
[akpm@linux-foundation.org: fix typo in comment]
Reported-by: Steven Noonan <steven@uplinklabs.net>
Tested-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Elena Ufimtseva <ufimtseva@gmail.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>	[3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit c65c1877 ("slub: use lockdep_assert_held") incorrectly
required that add_full() and remove_full() hold n->list_lock.  The lock
is only taken when kmem_cache_debug(s), since that's the only time it
actually does anything.

Require that the lock only be taken under such a condition.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

  drivers/md/bcache/extents.c: In function `btree_ptr_bad_expensive':
  drivers/md/bcache/extents.c:196: warning: format `%li' expects type `long int', but argument 4 has type `size_t'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently, update_note_header_size_elf64() and
update_note_header_size_elf32() will add the size of a PT_NOTE entry to
real_sz even if that causes real_sz to exceeds max_sz.  This patch
corrects the while loop logic in those routines to ensure that does not
happen and prints a warning if a PT_NOTE entry is dropped.  If zero
PT_NOTE entries are found or this condition is encountered because the
only entry was dropped, a warning is printed and an error is returned.

One possible negative side effect of exceeding the max_sz limit is an
allocation failure in merge_note_headers_elf64() or
merge_note_headers_elf32() which would produce console output such as
the following while booting the crash kernel.

  vmalloc: allocation failure: 14076997632 bytes
  swapper/0: page allocation failure: order:0, mode:0x80d2
  CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0-gbp1 #7
  Call Trace:
    dump_stack+0x19/0x1b
    warn_alloc_failed+0xf0/0x160
    __vmalloc_node_range+0x19e/0x250
    vmalloc_user+0x4c/0x70
    merge_note_headers_elf64.constprop.9+0x116/0x24a
    vmcore_init+0x2d4/0x76c
    do_one_initcall+0xe2/0x190
    kernel_init_freeable+0x17c/0x207
    kernel_init+0xe/0x180
    ret_from_fork+0x7c/0xb0

  Kdump: vmcore not initialized

  kdump: dump target is /dev/sda4
  kdump: saving to /sysroot//var/crash/127.0.0.1-2014.01.28-13:58:52/
  kdump: saving vmcore-dmesg.txt
  Cannot open /proc/vmcore: No such file or directory
  kdump: saving vmcore-dmesg.txt failed
  kdump: saving vmcore
  kdump: saving vmcore failed

This type of failure has been seen on a four socket prototype system
with certain memory configurations.  Most PT_NOTE sections have a single
entry similar to:

  n_namesz = 0x5
  n_descsz = 0x150
  n_type   = 0x1

Occasionally, a second entry is encountered with very large n_namesz and
n_descsz sizes:

  n_namesz = 0x80000008
  n_descsz = 0x510ae163
  n_type   = 0x80000008

Not yet sure of the source of these extra entries, they seem bogus, but
they shouldn't cause crash dump to fail.
Signed-off-by: Greg Pearson <greg.pearson@hp.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>