Add a new config for 4165 series over PCI and insert support
for two new 4165 series PCI IDs.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes sure that we're not trying to read/write any of
the FW debug data collected during d0i3.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Repeating the legacy rates avoids degrading quickly to
lower rates due to collisions which is common when doing
TCP Tx traffic in legacy.
This slightly improves TCP Tx throughput while working
in legacy in different scenarios.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If Tx failed because the STA was in powersave there's no point
in sending a BAR so avoid indicating AMPDU_NO_BACK to mac80211.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Organize and cleanup the consts used by rs.
This is part of making some of these configurable.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Make passive scan fragmentation depends on the number of active
interfaces. In case of single-MAC, make passive scan less fragmented.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to config the FW and to allocate monitor buffer driver should
run the function iwl_pcie_apply_destination immediately after FW sections
are loaded.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This configuration defines the ratio between number of scan iterations
where EBS is involved to those where it is not.
This configuration was left unconfigured due to inaccurate documentation.
Fix documentation as well.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Set the wakeup flag (of the d3 command) to configure the fw
to wakeup when sysassert happens while in d0i3.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A new TLV supplies the ADMA address for SDIO mode, allowing
the driver to configure the default base address to be this
(as given in the FW), rather than hardcoding the values to
use until the FW sends the ALIVE message.

Use the value given by the FW in the IWL_UCODE_TLV_SDIO_ADMA_ADDR
TLV for setting the default SDTM base address until the FW sends
the ALIVE message. If it isn't given in the FW - use the current
hardcoded values.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A number of places (still) use a direct operation, use
iwl_mvm_sta_from_mac80211() consistently. In one place
also move it into the variable initializer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There are a few places not using it, use it at those places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This device was renamed, but the external definition remained there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Some implementations (i.e. mini_rpm) assume the references
are managed only while the device is started.

Move the stale reference cleanup before stopping the
device in order to make them happy.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver and the firmware now support 2 different channels
at the same time. Advertise this capability to the stack.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

On hw restart, make sure to wait for d0i3 exit
(by checking the IN_D0I3 status bit).

This is needed in order to avoid the stale
d0i3_exit_work from doing harm (e.g. unref
cleared reference).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Consider the iwlwifi module param d0i3_disable when
considering whether d0i3 is supported.

(There is currently no need to differentiate between
supported and enabled, so keep the function as-is)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Enter d0i3 on suspend, and exit d0i3. Wait for the
command responses in both cases.

Use this mode in case of pcie trans.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow configuring additional d0i3 mode, in which the
fw will be configured to enter d0i3 only on suspend
(while keeping the wake_lock accounting as usual)

The d0i3 mode to use will be determined by the
underlying trans layer.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

d3 and d0i3 shouldn't be mutually exclusive. Set supported
wowlan triggers by looking for each of them, and check
on suspend/resume which flow should be used ("any" trigger
is supported by d0i3, and all the others by d3)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Implement the ref/unref trans ops and track both tx and
host command queues (and hold references while they
are not empty).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to add the offset. The type of the generic
memory dump will let the parser know that this is SRAM.
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of adding a dump type for each type of memory, change
the SMEM type to be a general purpose memory dump. Add the
type of the memory and its offset in the device in the dump
itself. This will allow an external parser to know where
this memory came from.

Note that since this type isn't really in use yet, this is
not a real problem.
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In NICs that have SMEM - add its content to the dump data
for later debug.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

nvm_file in family 8000 B step and A step differ. This means
that the driver should support 2 file name as default.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In case the rate mask for one of the modulations was zero the
max rate idx for that modulation was set to 32 (BITS_PER_LONG).
This is bad as it would later lead to an out of bounds access
to the expected tpt table. In most cases there was no real effect
as the expected tpt was set to 0 and this led to avoiding the
modulation effectively.
Fix the out of bounds access and explicitly skip the modulation
in case there's no rate allowed in it.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Clear the thermal throttling values when entering CT-kill, since
everything will be reinitialized anyway when we exit CT-kill.

Additionally, clear the dynamic_smps value in the initialization
funciton, for consistency.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The HW step member was left out of the core dump information. Fix this.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware is able to compensate the rssi when we hear
the frame on a different channel.
This is true for an offset up to 3 channels.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to collect the logs even if the firmware hasn't
crashed. Of course, crashing the firmware is an option, but
this is easier and nicer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When the driver is unload, the Manageability Engine should
know about that - send an event to inform it about this
event.
Reviewed-by: Reuven Borok <reuven.borok@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The antenna configuration has to be read also from OTP
Currently read only from FW image
Guideline: An antenna exists only if appears both in FW image & NVM
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The allocation of the DCCM between the data and the stack
can theoretically change without notice to the driver, but
the total size is HW-fixed. Since the stack CCM (runtime
stack) has also data important to the FW - this patch allows
pulling the whole DCCM in one piece and adds it to the dump
data.

If the size isn't known - just use the data part of the
DCCM as it appears in the FW TLVs.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The module version "in-tree:" or "in-tree:d" is useless; there
should be better (functional) ways to detect whether debugging
is enabled and other than that the version says nothing.

Therefore remove the driver version completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking updates from David Miller:

 1) New offloading infrastructure and example 'rocker' driver for
    offloading of switching and routing to hardware.

    This work was done by a large group of dedicated individuals, not
    limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
    Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu

 2) Start making the networking operate on IOV iterators instead of
    modifying iov objects in-situ during transfers.  Thanks to Al Viro
    and Herbert Xu.

 3) A set of new netlink interfaces for the TIPC stack, from Richard
    Alpe.

 4) Remove unnecessary looping during ipv6 routing lookups, from Martin
    KaFai Lau.

 5) Add PAUSE frame generation support to gianfar driver, from Matei
    Pavaluca.

 6) Allow for larger reordering levels in TCP, which are easily
    achievable in the real world right now, from Eric Dumazet.

 7) Add a variable of napi_schedule that doesn't need to disable cpu
    interrupts, from Eric Dumazet.

 8) Use a doubly linked list to optimize neigh_parms_release(), from
    Nicolas Dichtel.

 9) Various enhancements to the kernel BPF verifier, and allow eBPF
    programs to actually be attached to sockets.  From Alexei
    Starovoitov.

10) Support TSO/LSO in sunvnet driver, from David L Stevens.

11) Allow controlling ECN usage via routing metrics, from Florian
    Westphal.

12) Remote checksum offload, from Tom Herbert.

13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
    driver, from Thomas Lendacky.

14) Add MPLS support to openvswitch, from Simon Horman.

15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
    Klassert.

16) Do gro flushes on a per-device basis using a timer, from Eric
    Dumazet.  This tries to resolve the conflicting goals between the
    desired handling of bulk vs.  RPC-like traffic.

17) Allow userspace to ask for the CPU upon what a packet was
    received/steered, via SO_INCOMING_CPU.  From Eric Dumazet.

18) Limit GSO packets to half the current congestion window, from Eric
    Dumazet.

19) Add a generic helper so that all drivers set their RSS keys in a
    consistent way, from Eric Dumazet.

20) Add xmit_more support to enic driver, from Govindarajulu
    Varadarajan.

21) Add VLAN packet scheduler action, from Jiri Pirko.

22) Support configurable RSS hash functions via ethtool, from Eyal
    Perry.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
  Fix race condition between vxlan_sock_add and vxlan_sock_release
  net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
  net/mlx4: Add support for A0 steering
  net/mlx4: Refactor QUERY_PORT
  net/mlx4_core: Add explicit error message when rule doesn't meet configuration
  net/mlx4: Add A0 hybrid steering
  net/mlx4: Add mlx4_bitmap zone allocator
  net/mlx4: Add a check if there are too many reserved QPs
  net/mlx4: Change QP allocation scheme
  net/mlx4_core: Use tasklet for user-space CQ completion events
  net/mlx4_core: Mask out host side virtualization features for guests
  net/mlx4_en: Set csum level for encapsulated packets
  be2net: Export tunnel offloads only when a VxLAN tunnel is created
  gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
  cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
  net: fec: only enable mdio interrupt before phy device link up
  net: fec: clear all interrupt events to support i.MX6SX
  net: fec: reset fep link status in suspend function
  net: sock: fix access via invalid file descriptor
  net: introduce helper macro for_each_cmsghdr
  ...

Pull sound updates from Takashi Iwai:
 "This became a fairly large pull request.  In addition to the usual
  driver updates / fixes, there have been a high amount of cleanups in
  ASoC area, as well as control API helpers and kernel documentations
  fixes touching through the whole tree.

  In the driver side, the biggest changes are the support for new Intel
  SoC found on new x86 machines, and the updates of FireWire dice and
  oxfw drivers.

  Some remarkable items are below:

  ALSA core:
   - PCM mmap code cleanup, removal of arch-dependent codes
   - PCM xrun injection support
   - PCM hwptr tracepoint support
   - Refactoring of snd_pcm_action(), simplification of PCM locking
   - Robustified sequecner auto-load functionality
   - New control API helpers and lots of cleanups along with them
   - Lots of kerneldoc fixes and cleanups

  USB-audio:
   - The mixer resume code was largely rewritten, and the devices with
     quirks are resumed properly.
   - New hardware support: Focusrite Scarlett, Digidesign Mbox1,
     Denon/Marantz DACs, Zoom R16/24

  FireWire:
   - DICE driver updates with better duplex and sync support, including
     MIDI support
   - New OXFW driver for Oxford Semiconductor FW970/971 chipset,
     including the previous LaCie Speakers device.  Fullduplex and MIDI
     support included as well as DICE driver.

  HD-audio:
   - Refactoring the driver-caps quirk handling in snd-hda-intel
   - More consistent control names representing the topology better
   - Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
     fix, ASUS Z99He laptop EAPD

  ASoC:
   - Conversion of AC'97 drivers to use regmap, bringing us closer to
     the removal of the ASoC level I/O code
   - Clean up a lot of old drivers that were open coding things that
     have subsequently been implemented in the core
   - Some DAPM performance improvements
   - Removal of the now seldom used CODEC mutex
   - Lots of updates for the newer Intel SoC support, including support
     for the DSP and some Cherrytrail and Braswell machine drivers
   - Support for Samsung boards using rt5631 as the CODEC
   - Removal of the obsolete AFEB9260 machine driver
   - Driver support for the TI TS3A227E headset driver used in some
     Chrombeooks

  Others:
   - ASIHPI driver update and cleanups
   - Lots of dev_*() printk conversions
   - Lots of trivial cleanups for the codes spotted by Coccinelle"

* tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
  ALSA: pcxhr: NULL dereference on probe failure
  ALSA: lola: NULL dereference on probe failure
  ALSA: hda - Add "eapd" model string for AD1986A codec
  ALSA: hda - Add EAPD fixup for ASUS Z99He laptop
  ALSA: oxfw: Add hwdep interface
  ALSA: oxfw: Add support for capture/playback MIDI messages
  ALSA: oxfw: add support for capturing PCM samples
  ALSA: oxfw: Add support AMDTP in-stream
  ALSA: oxfw: Add support for Behringer/Mackie devices
  ALSA: oxfw: Change the way to start stream
  ALSA: oxfw: Add proc interface for debugging purpose
  ALSA: oxfw: Change the way to make PCM rules/constraints
  ALSA: oxfw: Add support for AV/C stream format command to get/set supported stream formation
  ALSA: oxfw: Change the way to name card
  ALSA: dice: Add support for MIDI capture/playback
  ALSA: dice: Add support for capturing PCM samples
  ALSA: dice: Support for non SYT-Match sampling clock source mode
  ALSA: dice: Add support for duplex streams with synchronization
  ALSA: dice: Change the way to start stream
  ALSA: jack: Add dummy snd_jack_set_key() definition
  ...

Pull devicetree changes from Grant Likely:
 "Lots of activity in the devicetree code for v3.18.  Most of it is
  related to getting all of the overlay support code in place, but there
  are other important things in there.

  Highlights:

   - OF_RECONFIG notifiers for SPI, I2C and Platform devices.  Those
     subsystems can now respond to live changes to the device tree.

   - CONFIG_OF_OVERLAY method for applying live changes to the device
     tree

   - Removal of the of_allnodes list.  This used to be used to iterate
     over all the nodes in the device tree, but it is unnecessary
     because the same thing can be done by iterating over the list of
     child pointers.  Getting rid of of_allnodes saves some memory and
     avoids the possibility of of_allnodes being sorted differently from
     the child lists.

   - Support for retrieving original DTB blob via sysfs.  Needed by
     kexec.

   - More unittests

   - Documentation and minor bug fixes"

* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
  of: Delete unnecessary check before calling "of_node_put()"
  of: Drop ->next pointer from struct device_node
  spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
  of: support passing console options with stdout-path
  of: add optional options parameter to of_find_node_by_path()
  of: Add bindings for chosen node, stdout-path
  of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
  ARM: dt: fix up PL011 device tree bindings
  of: base, fix of_property_read_string_helper kernel-doc
  of: remove select of non-existant OF_DEVICE config symbol
  spi/of: Add OF notifier handler
  spi/of: Create new device registration method and accessors
  i2c/of: Add OF_RECONFIG notifier handler
  i2c/of: Factor out Devicetree registration code
  of/overlay: Add overlay unittests
  of/overlay: Introduce DT overlay support
  of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
  of/reconfig: Always use the same structure for notifiers
  of/reconfig: Add debug output for OF_RECONFIG notifiers
  of/reconfig: Add empty stubs for the of_reconfig methods
  ...