Merge tag 'v4.9-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next

Pull rockchip clk driver updates from Heiko Stuebner:

The biggest addition is probably the special clock-type for ddr clock
control. While reading that clock is done the normal way from the
registers, setting it always requires some sort of special handling
to let the system survive this addition.

As the commit message explains, there are currently 3 handling-types
known. General SRAM-based code on rk3288 and before (which is waiting
essentially for the PIE support that is currently being worked on),
SCPI-based clk setting on the rk3368 through a coprocessor, which we
might support once the support for legacy scpi-variants has matured
and now on the rk3399 (and probably later) using a dcf controller that
is controlled from the arm-trusted-firmware and gets accessed through
firmware calls from the kernel. This is the variant we currently
support, but the clock type is made to support the other variants in
the future as well.

Apart from that slightly bigger chunk, we have a mix of PLL rates,
clock-ids and flags mainly for the rk3399.

And interestingly an iomap fix for the legacy gate driver, where I
hopefully could deter the submitter from actually using that in any
new works.

* tag 'v4.9-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  clk: rockchip: use the dclk_vop_frac clock ids on rk3399
  clk: rockchip: drop CLK_SET_RATE_PARENT from rk3399 fractional dividers
  clk: rockchip: add 2016M to big cpu clk rate table on rk3399
  clk: rockchip: add rk3399 ddr clock support
  clk: rockchip: add dclk_vop_frac ids for rk3399 vop
  clk: rockchip: add new clock-type for the ddrclk
  soc: rockchip: add header for ddr rate SIP interface
  clk: rockchip: add SCLK_DDRC id for rk3399 ddrc
  clk: rockchip: handle of_iomap failures in legacy clock driver
  clk: rockchip: mark rk3399 hdcp_noc and vio_noc as critical
  clk: rockchip: use general clock flag when registering pll
  clk: rockchip: delete the CLK_IGNORE_UNUSED from aclk_pcie on rk3399
  clk: rockchip: add 65MHz and 106.5MHz rates to rk3399 plls used for HDMI

Add a section for Renesas clock drivers, as found on Renesas ARM SoCs,
and list myself as the maintainer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Export the dclk_vop_frac out, so we can set the dclk_vop as the
child of dclk_vop_frac, and then we can start to take use of
the fractional dividers.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Currently the fractional divider clock time can't handle the
CLK_SET_RATE_PARENT flag. This is because, unlike normal dividers,
there is no clk_divider_bestdiv() function to try speeding up the parent
to see if it helps things.

Eventually someone could try to figure out how to make fractional
dividers able to use CLK_SET_RATE_PARENT, but until they do let's not
confuse the common clock framework (and anyone using it) by setting the
flag.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

We would prefer the 2016M as 2.0G than 1992M which seems odd, adding
it to big cpu clk rate table then we can set 2016M in dts.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

add ddrc clock setting, so we can do ddr frequency
scaling on rk3399 platform in future.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Export the dclk_vop_frac out, so we can set the dclk_vop as the
child of dclk_vop_frac, and then we can start to take use of
the fractional dividers.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the PWM related clocks in order to be referenced as PWM source
clocks.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1471870177-10609-1-git-send-email-narmstrong@baylibre.com

This patch adds support for the meson8b clock gates. Most of
them are disabled by Amlogic U-Boot, but need to be enabled
for ethernet, USB and many other components.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-7-git-send-email-serveralex@gmail.com

The macro used gxbb_ prefix for clock definitions. In order
to share the macro between gxbb and meson8b, the prefix must
be moved to gxbb.c.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-6-git-send-email-serveralex@gmail.com

Only expose future CLKID constants if necessary. This patch
removes CLK_NR_CLKS from the DT bindings but leaves all previously
defined CLKIDs there to keep backward compatibility.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-5-git-send-email-serveralex@gmail.com

Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-4-git-send-email-serveralex@gmail.com

Move the register definitions into a separate header file
to reflect the gxbb implementation.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-3-git-send-email-serveralex@gmail.com

Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-2-git-send-email-serveralex@gmail.com

Changing the rate of the DDR clock needs special care, as the DDR
is of course in use and will react badly if the rate changes under it.

Over time different approaches to handle that were used.

Past SoCs like the rk3288 and before would store some code in SRAM
while the rk3368 used a SCPI variant and let a coprocessor handle that.

New rockchip platforms like the rk3399 have a dcf controller to do ddr
frequency scaling, and support for this controller will be implemented
in the arm-trusted-firmware.

This new clock-type should over time handle all these methods for
handling DDR rate changes, but right now it will concentrate on the
SIP interface used to talk to ARM trusted firmware.

The SIP interface counterpart was merged from pull-request #684 [0]
into the upstream arm-trusted-firmware codebase.

[0] https://github.com/ARM-software/arm-trusted-firmware/pull/684Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add a header for the SIP interface defined to access the dcf controller
handling ddr rate changes on rk3399 (and most likely later socs).

This interface is shared between the clock driver as well as the
devfreq driver.

The SIP interface counterpart was merged from pull-request #684 [0]
into the upstream arm-trusted-firmware codebase.

[0] https://github.com/ARM-software/arm-trusted-firmware/pull/684Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the needed id for the ddr clock.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Currently we see the following error when using the SAI audio
driver on mx7:

Division by zero in kernel.
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.8.0-rc3-next-20160823
Hardware name: Freescale i.MX7 Dual (Device Tree)
Backtrace:
[<c010b70c>] (dump_backtrace) from [<c010b8a8>] (show_stack+0x18)
r6:60000013 r5:ffffffff r4:00000000 r3:00000000
[<c010b890>] (show_stack) from [<c03e9324>] (dump_stack+0xb0/0xe)
[<c03e9274>] (dump_stack) from [<c010b578>] (__div0+0x18/0x20)
r8:00000000 r7:ffffffff r6:ffffffff r5:00000000 r4:00000000 r3:0
[<c010b560>] (__div0) from [<c03e795c>] (Ldiv0_64+0x8/0x18)
[<c06cd860>] (divider_get_val) from [<c06cda28>] (clk_divider_se)

This error happens due to the lack of definition of the
IMX7D_PLL_AUDIO_TEST_DIV/IMX7D_PLL_AUDIO_POST_DIV clocks.

Add support for them.

Tested on a imx7s-warp board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

This patch reverts commit 023bd716 ("clk: skip unnecessary
set_phase if nothing to do"), fixing two problems:

* in some SoCs, the hardware phase delay depends on the rate ratio of
  the clock and its parent. So, changing this ratio may imply to set
  new hardware values, even if the logical delay is the same.

* when the delay was the same as previously, an error was returned.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Fixes: 023bd716 ("clk: skip unnecessary set_phase if nothing to do")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Merge tag 'clk-renesas-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next

Pull renesas r8a7796 SDHI clock support from Geert Uytterhoeven:

Add all clocks needed to use the SDHI interfaces on the Renesas R-Car M3-W
(r8a7796) SoC.

* tag 'clk-renesas-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
  clk: renesas: r8a7796: Add SDIF clocks
  clk: renesas: r8a7796: Add GPIO clocks

* clk-fixes:
  clk: rockchip: mark aclk_emmc_noc as a critical clock on rk3399
  clk: rockchip: fix incorrect GATE bits for {c, g}pll_aclk_perihp_src on rk3399
  clk: rockchip: fix incorrect aclk_emmc source gate bits on rk3399
  clk: rockchip: fix rk3399 aclk_vio gate bit

Merge tag 'v4.8-rockchip-clk-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-fixes

Some fixes for rk3399 register errors that revealed themself
during actual use.

* tag 'v4.8-rockchip-clk-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  clk: rockchip: mark aclk_emmc_noc as a critical clock on rk3399
  clk: rockchip: fix incorrect GATE bits for {c, g}pll_aclk_perihp_src on rk3399
  clk: rockchip: fix incorrect aclk_emmc source gate bits on rk3399
  clk: rockchip: fix rk3399 aclk_vio gate bit

This adds support for the two ICST525-based clocks on the
Integrator/AP baseboard, as documented in the board manual
"Integrator/AP ASIC Development Motherboard", ARM DUI0098 B,
pages 3-15 thru 3-18.

Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[sboyd@codeaurora.org: fixed uninitialized val warning]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

__of_clk_get_hw_from_provider() is confusing because it will
return EPROBE_DEFER if there isn't a ->get() or ->get_hw()
function pointer in a provider. That's just a bug though, and we
used to NULL pointer exception when ->get() was missing anyway,
so let's make this more obvious that they're not optional. The
assumption is that most providers will implement ->get_hw() so we
only fallback to the ->get() function if necessary. This
clarifies the intent and removes any possibility of probe defer
happening if clk providers are buggy.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

In the commit 929e7f3b ("clk: Make of_clk_get_parent_count() return
unsigned ints") of_clk_get_parent_count has been modified to return
unsigned int. There is also a dummy implementation of the same function
for configs without CONFIG_OF. For the consistency it should be updated
as well.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The Integrator/AP and Integrator/CP have special derivatives
of the ICST525 control registers, where some bits have been
hardwired but others are possible to adjust, resulting in a
control register that makes it possible to set an even,
desired megahertz value.

The Integrator/AP and Integrator/CP have slightly different
layout so we support them using different compatible
strings.

After adding these clocks, the Integrator-specific cpufreq
driver can be switched over to use the generic operating
point device tree cpufreq driver.

Instead of simply writing a value to the oscillator control
register we switch to the more elaborate method of providing
a bitmask and use regmap_update_bits() to poke the right bits
for the desired frequency, this is needed since these control
registers sometimes control more than one clock.

Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The Integrator/AP and Integrator/CP core modules have special
versions of the ICST525 interface hardcoding some bits. Create
special compatible strings to identify these variants, also
explain a bit what is going on.

Cc: devicetree@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

This patch adds missing 2 PCIE common reset lines.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

This patch corrects the register offset for pcie2 pipe clock.
Offset according to datasheet is 0x6e018 instead of 0x6e108.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: b1e010c0 ("clk: qcom: Add MSM8996 Global Clock Control (GCC) driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

This patch selects QCOM_GDSC Kconfig for msm8996 GCC and MMCC clock
controllers, as these provide some of the gdscs on the SOC.

Also selecting this config will make it align with other drivers which
do the same.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 52111672 ("clk: qcom: gdsc: Add GDSCs in msm8996 GCC")
Fixes: 7e824d50 ("clk: qcom: gdsc: Add mmcc gdscs for msm8996 family")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

* clk-fixes:
  clk: tegra: remove TEGRA_PLL_USE_LOCK for PLLD/PLLD2

Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.

Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: <uclinux-h8-devel@lists.sourceforge.jp>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers in this driver, allowing us to
move closer to a clear split of consumer and provider clk APIs.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.

Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.

Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>