This patch adds support for the 7" LCD display available for Nitrogen6x:
http://boundarydevices.com/product/7-800x480-display/

Also add label to backlight_lcd and connect it to the panel.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device tree node for touchscreen support on Colibri VF50. The
touchscreen functionality on VF50 uses the ADC channels of Vybrid
and some GPIOs. Also add pinctrl nodes for proper pinmux.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device tree node to support iomuxc-lpsr controller, fsl,input-sel
phandle allows to get input select register base address which is
shared from main iomuxc controller.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable fec1 and fec2 for i.MX7d-sdb board.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

- Add imx7 SoC GPIO1 pad iomuxc settings
  <mux_reg conf_reg input_reg mux_mode input_val>
- Fix UART input select daisy chain setting values
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The INA220 monitors both shunt drop and supply voltage.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds dma-coherent property for eTSEC nodes, so
coherent DMA operations are supported.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for USBOTG1 and USBOTG2.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add USB OTG and Host support.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add fec1 and fec2 nodes for i.MX7d soc.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add touch screen surpport for i.MX6UL-EVK board.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add imx6ul touchscreen controller support.

TSC module need ADC2 module to measure the touchscreen
coordinate value. This patch put TSC and ADC2 together,
make ADC2 module only be used for TSC, can't be used as
a normal ADC.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the PWM1-4 nodes.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DCP block present on MX6SL is compatible with the one on MX28,
so add the compatible string and also complete the interrupt entries.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Starting with commit 8947e396 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.

Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch enables On Chip OTP support for i.MX23 and i.MX28 SoCs,
but keeps the old compatible string.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx7d-sdb board has a eMMC5.0 on usdhc3. This eMMC support HS400.
This patch add usdhc3 support for HS400
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6UL can be powered off by programming SNVS.

When long press ON/OFF button(5 seconds),
PMIC_ON_REQ pin will be set to low and external
PMIC will be powered off.

And system can be powered on by long press ON/OFF
button again.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add MMDC support for i.MX6UL.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add SRAM support for i.MX6UL, it has 128KB ocram
starting from 0x900000.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX clock updates for 4.4:
 - A couple of fixes on i.MX31 and i.MX35 clock initialization functions
   which makes mxc_timer_init() currently be called twice for DT boot.
 - Increase i.MX6UL AXI bus clock rate to 264MHz which is the optimal
   design target.
 - Add a few missing clocks, ADC clock for i.MX7D, OCOTP clock for
   Vybrid, and SPDIF_GCLK for i.MX6.
 - A series from Lucas to fix early debug UART clock setup.  This is
   currently a one-off fix for i.MX platform, and can be extended to
   become a generic solution later.

Correct SPDIF clock setting issue in clock tree, the SPDIF_GCLK is also
one clock of SPDIF, which is missed before.

We found an issue that imx can't enter low power mode with spdif
if IMX6x_CLK_SPDIF is used as the core clock of spdif. Because
spdif driver will register IMX6x_CLK_SPDIF clock to regmap, regmap will do
clk_prepare in init function, then IMX6x_CLK_SPDIF clock is prepared in probe,
so its parent clock (PLL clock) is prepared, the prepare operation of
PLL clock is to enable the clock. But I.MX needs all PLL clock is disabled,
then it can enter low power mode.

So we can't use IMX6x_CLK_SPDIF as the core clock of spdif, the correct spdif
core clock is SPDIF_GCLK, which share same gate bit with IMX6x_CLK_SPDIF clock.
SPDIF_GCLK's parent clock is ipg clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add ADC root clock support in imx7d clock tree.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

mxc_timer_init must not be called from within mx31_clocks_init_dt. It will
eventually be called by imx31_timer_init_dt
(drivers/clocksource/timer-imx-gpt.c).
This arranges the initialization code similar to clk-imx27.c
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Both earlycon and eralyprintk depend on the bootloader setup UART
clocks being retained. This patch adds the common logic to detect such
situations and make the information available to the clock drivers, as
well as adding the facilities to disable those clocks at the end of
the kernel init.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

mxc_timer_init must not be called from within mx35_clocks_init_dt. It will
eventually be called by imx31_timer_init_dt
(drivers/clocksource/timer-imx-gpt.c).
This arranges the initialization code similar to clk-imx27.c
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add clock support for Vybrid On-Chip One Time Programmable
(OCOTP) controller.

While the OCOTP block does not require explicit clock gating,
for programming the OCOTP timing register the clock rate of
ipg clock is required for timing calculations related to fuse
and shadow register read sequence. We explicitly specify the
ipg clock for OCOTP as a result.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On i.MX6UL, AXI clock rate's design target is 264MHz, but by default
it is only set to 198MHz which is NOT good enough for performance,
this patch increases AXI clock rate from 198MHz to 264MHz to meet
the design target, this is done by switching its parent clock
"periph" from 396MHz PFD to 528MHz PLL.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull CRIS updates from Jesper Nilsson:
 "Mostly removal of old cruft of which we can use a generic version, or
  fixes for code not commonly run in the cris port, but also additions
  to enable some good debug"

* tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits)
  CRISv10: delete unused lib/dmacopy.c
  CRISv10: delete unused lib/old_checksum.c
  CRIS: fix switch_mm() lockdep splat
  CRISv32: enable LOCKDEP_SUPPORT
  CRIS: add STACKTRACE_SUPPORT
  CRISv32: annotate irq enable in idle loop
  CRISv32: add support for irqflags tracing
  CRIS: UAPI: use generic types.h
  CRIS: UAPI: use generic shmbuf.h
  CRIS: UAPI: use generic msgbuf.h
  CRIS: UAPI: use generic socket.h
  CRIS: UAPI: use generic sembuf.h
  CRIS: UAPI: use generic sockios.h
  CRIS: UAPI: use generic auxvec.h
  CRIS: UAPI: use generic headers via Kbuild
  CRIS: UAPI: fix elf.h export
  CRIS: don't make asm/elf.h depend on asm/user.h
  CRIS: UAPI: fix ptrace.h
  CRISv32: Squash compile warnings for axisflashmap
  CRISv32: Add GPIO driver to the default configs
  ...