- 07 Jun, 2016 14 commits
-
-
Jamal Hadi Salim authored
Signed-off-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Amir Vadai authored
In order to make a filter processed only by hardware, skip_sw flag should be supplied. This is an addition to the already existing skip_hw flag (filter will be processed by software only). If no flag is specified, filter will be processed by both software and hardware. If only hardware offloaded filters exist, fl_classify() will return without doing anything. A following userspace patch will be sent once kernel patch is accepted. Example: tc filter add dev enp0s9 protocol ip prio 20 parent ffff: \ flower \ ip_proto 6 \ indev enp0s9 \ skip_sw \ action skbedit mark 0x1234 Signed-off-by:
Amir Vadai <amirva@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Acked-by:
John Fastabend <john.r.fastabend@intel.com> Signed-off-by:
-
David S. Miller authored
Yuval Mintz says: ==================== qed: IOV series - relax firmware requirements In order for VFs to work, current implementation demands that the VF's requried storm firmware would be exactly the version that was loaded by the PF, which is a very harsh requirement. This patch series is intended to relax this - the recently submitted firmware is intended to be forward/backward compatible in its fastpath [slowpath is configured by PF on behalf of VF], and so VFs would only be required of having the same major faspath HSI in order to work. Most of the other patches in this series extend current forward compatibilty of driver to reduce chance of breaking PF/VF compatibility in the future. A few are unrelated IOV changes. ==================== Signed-off-by: -
Yuval Mintz authored
If a future VF would send the PF an unknown message, the PF today would not send a reply. This would have 2 bad effects: a. VF would have to timeout on the request. b. If VF were to send an additional message to PF, firmware would mark it as malicious. Instead, if there's some valid reply-address on the message - let the PF answer and tell the VF it doesn't know the message. Signed-off-by:Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
-
Yuval Mintz authored
The only limitation relating to MACs the PF enforce today on its VFs is in case it has a forced-unicast MAC address for them, in which case they can't configure other unicast addresses. Specifically, the PF isn't enforcing the number of MAC addresse a VF can configure regardless of the nubmer of such filters agreed upon by PF and VF during the acquisition process. PF's shadow-config is now extended to also contain information about its VFs' unicast addresses configuration, allowing such enforcement. Signed-off-by:
-
Yuval Mintz authored
Today, the VF is aware of its queues context-ids, and calculates the doorbell address when opening its queues on its own. The configuration of doorbells in HW can sometime in the future be changed by the PF [hw has several configurable features that might affect doorbell addresses, e.g., dpm support], this would break compatibility with older VFs as their calculated doorbell addresses would be incorrect for such a configuration. In order to avoid such a backward compatibility failure, let the PF make the calculation of the doorbell offset based on the context-id, and pass that to the VF. Signed-off-by:
-
Yuval Mintz authored
There are several requests the VF can make toward the PF which the driver would pass to firmware without checking the validity first - specifically, opening queues and updating vports. Such configurations might cause the firmware to assert. This adds validation of the legality of said configurations on the PF side before passing it onward via ramrod to firmware. Signed-off-by:
-
Yuval Mintz authored
One of the goals of the vf's first message to the PF [acquire] is to learn about the number of resources available to it [macs, vlans, etc.]. This is done via negotiation - the VF requires a set of resources, which the PF either approves or disaproves and sends a smaller set of resources as alternative. In this later case, the VF is then expected to either abort the probe or re-send the acquire message with less required resources. While this infrastructure exists since the initial submision of qed SRIOV support, it's in fact completely inoperational - PF isn't really looking into the resources the VF has asked for and is never going to reply to the VF that it lacks resources. This patch addresses this flow, fixing it and allowing the PF and VF to actually agree on a set of resources. Signed-off-by:
-
Yuval Mintz authored
Current driver require an exact match between VF and PF storm firmware; Any difference would fail the VF acquire message, causing the VF probe to be aborted. While there's still dependencies between the two, the recent FW submission has relaxed the match requirement - instead of an exact match, there's now a 'fastpath' HSI major/minor scheme, where VFs and PFs that match in their major number can co-exist even if their minor is different. In order to accomadate this change some changes in the vf-start init flow had to be made, as the VF start ramrod now has to be sent only after PF learns which fastpath HSI its VF is requiring. Signed-off-by:
-
Eric Dumazet authored
Note: Tom Herbert posted almost same patch 3 months back, but for different reasons. The reasons we want to get rid of this spin_trylock() are : 1) Under high qdisc pressure, the spin_trylock() has almost no chance to succeed. 2) We loop multiple times in softirq handler, eventually reaching the max retry count (10), and we schedule ksoftirqd. Since we want to adhere more strictly to ksoftirqd being waked up in the future (https://lwn.net/Articles/687617/), better avoid spurious wakeups. 3) calls to __netif_reschedule() dirty the cache line containing q->next_sched, slowing down the owner of qdisc. 4) RT kernels can not use the spin_trylock() here. With help of busylock, we get the qdisc spinlock fast enough, and the trylock trick brings only performance penalty. Depending on qdisc setup, I observed a gain of up to 19 % in qdisc performance (1016600 pps instead of 853400 pps, using prio+tbf+fq_codel) ("mpstat -I SCPU 1" is much happier now) Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Tom Herbert <tom@herbertland.com> Acked-by:
Tom Herbert <tom@herbertland.com> Signed-off-by:
-
Jason Wang authored
We don't stop rx polling socket during rx processing, this will lead unnecessary wakeups from under layer net devices (E.g sock_def_readable() form tun). Rx will be slowed down in this way. This patch avoids this by stop polling socket during rx processing. A small drawback is that this introduces some overheads in light load case because of the extra start/stop polling, but single netperf TCP_RR does not notice any change. In a super heavy load case, e.g using pktgen to inject packet to guest, we get about ~8.8% improvement on pps: before: ~1240000 pkt/s after: ~1350000 pkt/s Signed-off-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Bhaktipriya Shridhar authored
alloc_workqueue replaces deprecated create_workqueue(). A dedicated workqueue has been used since the workitem viz (&db_wq->wk.work which maps to check_db_timeout) is involved in normal device operation. WQ_MEM_RECLAIM has been set to guarantee forward progress under memory pressure, which is a requirement here. Since there are only a fixed number of work items, explicit concurrency limit is unnecessary. flush_workqueue is unnecessary since destroy_workqueue() itself calls drain_workqueue() which flushes repeatedly till the workqueue becomes empty. Signed-off-by:
Bhaktipriya Shridhar <bhaktipriya96@gmail.com> Signed-off-by:
-
Bhaktipriya Shridhar authored
alloc_workqueue replaces deprecated create_workqueue(). A dedicated workqueue has been used since the workitem viz (&cwq->wk.work which maps to oct_poll_req_completion) is involved in normal device operation. WQ_MEM_RECLAIM has been set to guarantee forward progress under memory pressure, which is a requirement here. Since there are only a fixed number of work items, explicit concurrency limit is unnecessary. flush_workqueue is unnecessary since destroy_workqueue() itself calls drain_workqueue() which flushes repeatedly till the workqueue becomes empty. Hence the call to flush_workqueue() has been dropped. Signed-off-by:
-
Aaron Conole authored
This commit adds the feature bit and associated mtu device entry for the virtio network device. When a virtio device comes up, it checks the feature bit for the VIRTIO_NET_F_MTU feature. If such feature bit is enabled, the driver will read the advised MTU and use it as the initial value. Signed-off-by:
Aaron Conole <aconole@redhat.com> Signed-off-by:
-
- 06 Jun, 2016 12 commits
-
-
David S. Miller authored
This reverts commit 2fb7ea45. It results in build errors because ip6_input is not a symbol exported to modules. Signed-off-by:
-
David S. Miller authored
David Ahern says: ==================== net: vrf: Add support for local traffic to local addresses Add support for locally originated traffic to VRF-local addresses, be it addresses on enslaved devices or addresses on the VRF device: $ ip addr show dev red 33: red: <NOARP,MASTER,UP,LOWER_UP> mtu 65536 qdisc pfifo_fast state UP group default qlen 1000 link/ether be:00:53:b5:e4:25 brd ff:ff:ff:ff:ff:ff inet 1.1.1.1/32 scope global red valid_lft forever preferred_lft forever inet6 1111:1::1/128 scope global valid_lft forever preferred_lft forever $ ip addr show dev eth1 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000 link/ether 02:e0:f9:79:34:bd brd ff:ff:ff:ff:ff:ff inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1 valid_lft forever preferred_lft forever inet6 2100:1::1/120 scope global valid_lft forever preferred_lft forever inet6 fe80::e0:f9ff:fe79:34bd/64 scope link valid_lft forever preferred_lft forever $ ping -c1 -I red 10.100.1.1 ping: Warning: source address might be selected on device other than red. PING 10.100.1.1 (10.100.1.1) from 10.100.1.1 red: 56(84) bytes of data. 64 bytes from 10.100.1.1: icmp_seq=1 ttl=64 time=0.057 ms $ ping -c1 -I red 1.1.1.1 PING 1.1.1.1 (1.1.1.1) from 1.1.1.1 red: 56(84) bytes of data. 64 bytes from 1.1.1.1: icmp_seq=1 ttl=64 time=0.136 ms --- 1.1.1.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.136/0.136/0.136/0.000 ms $ ping6 -c1 -I red 2100:1::1 ping6: Warning: source address might be selected on device other than red. PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes 64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.167 ms --- 2100:1::1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.167/0.167/0.167/0.000 ms $ ping6 -c1 -I red 1111::1 PING 1111::1(1111::1) from 1111:1::1 red: 56 data bytes 64 bytes from 1111::1: icmp_seq=1 ttl=64 time=0.187 ms --- 1111::1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.187/0.187/0.187/0.000 ms This change also enables use of loopback address on the VRF device: $ ip addr add dev red 127.0.0.1/8 $ ping -c1 -I red 127.0.0.1 PING 127.0.0.1 (127.0.0.1) from 127.0.0.1 red: 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.058 ms ==================== Signed-off-by: -
David Ahern authored
Add support for locally originated traffic to VRF-local IPv6 addresses. Similar to IPv4 a local dst is set on the skb and the packet is reinserted with a call to netif_rx. With this patch, ping, tcp and udp packets to a local IPv6 address are successfully routed: $ ip addr show dev eth1 4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000 link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1 valid_lft forever preferred_lft forever inet6 2100:1::1/120 scope global valid_lft forever preferred_lft forever inet6 fe80::e0:f9ff:fe1c:b974/64 scope link valid_lft forever preferred_lft forever $ ping6 -c1 -I red 2100:1::1 ping6: Warning: source address might be selected on device other than red. PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes 64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.098 ms ip6_input is exported so the VRF driver can use it for the dst input function. The dst_alloc function for IPv4 defaults to setting the input and output functions; IPv6's does not. VRF does not need to duplicate the Rx path so just export the ipv6 input function. Signed-off-by:David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
David Ahern authored
Add support for locally originated traffic to VRF-local addresses. If destination device for an skb is the loopback or VRF device then set its dst to a local version of the VRF cached dst_entry and call netif_rx to insert the packet onto the rx queue - similar to what is done for loopback. This patch handles IPv4 support; follow on patch handles IPv6. With this patch, ping, tcp and udp packets to a local IPv4 address are successfully routed: $ ip addr show dev eth1 4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000 link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1 valid_lft forever preferred_lft forever inet6 2100:1::1/120 scope global valid_lft forever preferred_lft forever inet6 fe80::e0:f9ff:fe1c:b974/64 scope link valid_lft forever preferred_lft forever $ ping -c1 -I red 10.100.1.1 ping: Warning: source address might be selected on device other than red. PING 10.100.1.1 (10.100.1.1) from 10.100.1.1 red: 56(84) bytes of data. 64 bytes from 10.100.1.1: icmp_seq=1 ttl=64 time=0.057 ms This patch also enables use of IPv4 loopback address on the VRF device: $ ip addr add dev red 127.0.0.1/8 $ ping -c1 -I red 127.0.0.1 PING 127.0.0.1 (127.0.0.1) from 127.0.0.1 red: 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.058 ms Signed-off-by: -
David Ahern authored
Move the stripping of the ethernet header from is_ip_tx_frame into the ipv4 and ipv6 outbound functions. If the packet is destined to a local address the header is retained since the packet is sent back to netif_rx. Collapse vrf_send_v4_prep into vrf_process_v4_outbound. Signed-off-by:
-
David S. Miller authored
Vitaly Kuznetsov says: ==================== hv_netvsc: cleanup after untangling the pointer mess Changes since v1: - resend when net-next is open [David Miller] - rebased to current net-next. After we made traveling through our internal structures explicit it became obvious that some functions take arguments they don't need just to do redundant pointer travel and get to what they really need while their callers already have the required information. This is just a cleanup series with no functional changes intended. It doesn't pretend to be complete, additional cleanup of other functions may follow. ==================== Signed-off-by: -
Vitaly Kuznetsov authored
The only caller rndis_filter_device_add() has 'struct net_device' pointer already. Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
-
Vitaly Kuznetsov authored
We unpack 'struct net_device' in netvsc_set_mac_addr() to get to 'struct hv_device' pointer which we use in rndis_filter_set_device_mac() to get back to 'struct net_device'. Signed-off-by:
-
Vitaly Kuznetsov authored
Both rndis_filter_open()/rndis_filter_close() use struct hv_device to reach to struct netvsc_device only and all callers have it already. While on it, rename net_device to nvdev in rndis_filter_open() as net_device is misleading. Signed-off-by:
-
Vitaly Kuznetsov authored
Make it easier to get 'struct netvsc_device' from 'struct net_device' and 'struct hv_device' by introducing inline helpers. Signed-off-by:
-
Vitaly Kuznetsov authored
net_device_ctx is assigned in the very beginning of the function and 'net' pointer doesn't change. Signed-off-by:
-
Michal Kubeček authored
Before commit 6d7b857d ("net: use lib/percpu_counter API for fragmentation mem accounting"), setting the reassembly high threshold to 0 prevented fragment reassembly as first fragment would be always evicted before second could be added to the queue. While inefficient, some users apparently relied on this method. Since the commit mentioned above, a percpu counter is used for reassembly memory accounting and high batch size avoids taking slow path in most common scenarios. As a result, a whole full sized packet can be reassembled without the percpu counter's main counter changing its value so that even with high_thresh set to 0, fragmented packets can be still reassembled and processed. Add explicit check preventing reassembly if high threshold is zero. Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
- 05 Jun, 2016 14 commits
-
-
David S. Miller authored
Kejian Yan says: ==================== net: hns: add support of ACPI This series adds HNS support of acpi. The routine will call some ACPI helper functions, like acpi_dev_found() and acpi_evaluate_dsm(), which are not included in other cases. In order to make system compile successfully in other cases except ACPI, it needs to add relative stub functions to linux/acpi.h. And we use device property functions instead of serial helper functions to suport both DT and ACPI cases. And then add the supports of ACPI for HNS. change log: v3->v4: mii-id gets from dev-name instead of address v2->v3: 1. add Review-by: Andy Shevchenko 2. fix the potential memory leak v1 -> v2: 1. use acpi_dev_found() instead of acpi_match_device_ids() to check if it is a acpi node. 2. use is_of_node() instead of IS_ENABLED() to check if it is a DT node. 3. split the patch("add support of acpi for hns-mdio") into two patches: 3.1 Move to use fwnode_handle 3.2 Add ACPI 4. add the patch which subject is dsaf misc operation method 5. fix the comments by Andy Shevchenko ==================== Signed-off-by: -
Kejian Yan authored
Enet needs to get configration parameter by acpi. This patch adds support of ACPI for enet. The configuration parameter will be configed in BIOS. Signed-off-by:
Kejian Yan <yankejian@huawei.com> Signed-off-by:
Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by:
-
Kejian Yan authored
The miscellaneous operation is implemented in BIOS, the kernel can call _DSM method help to call the implementation in ACPI case. Here is a patch to do that. Signed-off-by:
-
Kejian Yan authored
In ACPI case, there is no interface to register phy device to mdio-bus. Phy device has to be registered itself to mdio-bus, and then enet can get the phy device's info so that it can config the phy-device to help to trasmit and receive data. HNS hardware topology is as below. The MDIO controller may control several PHY-devices, and each PHY-device connects to a MAC device. PHY-devices will register when each mac find PHY device in initial sequence. cpu | | ------------------------------------------- | | | | | | | dsaf | MDIO | MDIO | --------------------------- | | | | | | | | | | | | | | MAC MAC MAC MAC | | | | | | | ---- |-------- |-------- | | -------- || || || || PHY PHY PHY PHY Signed-off-by: -
Kejian Yan authored
Dsaf needs to get configuration parameter by ACPI, so this patch add support of ACPI. Signed-off-by:
-
Kejian Yan authored
The misc operation for different hw platform may be different, if using current implementation, it will add a new branch on each function for every new hw platform, so we add a method for this operation. Signed-off-by:
-
Kejian Yan authored
As device_node is only used by DT case, HNS needs to treat the other cases including ACPI. It needs to use uniform ways to handle both of DT and ACPI. This patch chooses phy_device, and of_phy_connect and of_phy_attach are only used by DT case. It needs to use uniform interface to handle that sequence by both DT and ACPI. Signed-off-by:
-
Kejian Yan authored
As device_node is only used by DT case, it is expected to find uniform ways. So fwnode_handle is the suitable method. Signed-off-by:
-
Kejian Yan authored
As irq_of_parse_and_map is only used by DT case, it is excepted to use a uniform interface. So it is used platform_get_irq() instead. Signed-off-by:
-
Kejian Yan authored
OF series functions can be used only for DT case. Use unified device property function instead to support both DT and ACPI. Signed-off-by:
-
Kejian Yan authored
hns-mdio needs to register itself to mii-bus. The info of the device can be read by both DT and ACPI. HNS tries to call Linux PHY driver to help access PHY-devices, the HNS hardware topology is as below. The MDIO controller may control several PHY-devices, and each PHY-device connects to a MAC device. The MDIO will be registered to mdiobus, then PHY-devices will register when each mac find PHY device. cpu | | ------------------------------------------- | | | | | | | dsaf | MDIO | MDIO | --------------------------- | | | | | | | | | | | | | | MAC MAC MAC MAC | | | | | | | ---- |-------- |-------- | | -------- || || || || PHY PHY PHY PHY And the driver can handle reset sequence by _RST method in DSDT in ACPI case. Signed-off-by: -
Kejian Yan authored
Hns-mdio only supports DT case now. do some cleanup to prepare for introducing other cases later, no functional change. Signed-off-by:
-
Kejian Yan authored
acpi_evaluate_dsm() will be used to handle the _DSM method in ACPI case. It will be compiled in non-ACPI case, but the function is in acpi_bus.h and acpi_bus.h can only be used in ACPI case, so this patch add the stub function to linux/acpi.h to make compiled successfully in non-ACPI cases. Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Signed-off-by:
-
Kejian Yan authored
acpi_dev_found() will be used to detect if a given ACPI device is in the system. It will be compiled in non-ACPI case, but the function is in acpi_bus.h and acpi_bus.h can only be used in ACPI case, so this patch add the stub function to linux/acpi.h to make compiled successfully in non-ACPI cases. Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Signed-off-by:
-
