- 07 Oct, 2012 18 commits
-
-
Russ Gorby authored
commit 5e44708f upstream. There were some locking holes in the management of the MUX's message queue for 2 code paths: 1) gsmld_write_wakeup 2) receipt of CMD_FCON flow-control message In both cases gsm_data_kick is called w/o locking so it can collide with other other instances of gsm_data_kick (pulling messages tx_tail) or potentially other instances of __gsm_data_queu (adding messages to tx_head) Changed to take the tx_lock in these 2 cases Signed-off-by:
Russ Gorby <russ.gorby@intel.com> Tested-by:
Yin, Fengwei <fengwei.yin@intel.com> Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sarah Sharp authored
commit 80fab3b2 upstream. When a device with an isochronous endpoint is behind a hub plugged into the Intel Panther Point xHCI host controller, and the driver submits multiple frames per URB, the xHCI driver will set the Block Event Interrupt (BEI) flag on all but the last TD for the URB. This causes the host controller to place an event on the event ring, but not send an interrupt. When the last TD for the URB completes, BEI is cleared, and we get an interrupt for the whole URB. However, under a Panther Point xHCI host controller, if the parent hub is unplugged when one or more events from transfers with BEI set are on the event ring, a port status change event is placed on the event ring, but no interrupt is generated. This means URBs stop completing, and the USB device disconnect is not noticed. Something like a USB headset will cause mplayer to hang when the device is disconnected. If another transfer is sent (such as running `sudo lsusb -v`), the next transfer event seems to "unstick" the event ring, the xHCI driver gets an interrupt, and the disconnect is reported to the USB core. The fix is not to use the BEI flag under the Panther Point xHCI host. This will impact power consumption and system responsiveness, because the xHCI driver will receive an interrupt for every frame in all isochronous URBs instead of once per URB. Intel chipset developers confirm that this bug will be hit if the BEI flag is used on any endpoint, not just ones that are behind a hub. This patch should be backported to kernels as old as 3.0, that contain the commit 69e848c2 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
Khalid Aziz authored
commit 70839090 upstream. Some of the EFI variable attributes are missing from print out from /sys/firmware/efi/vars/*/attributes. This patch adds those in. It also updates code to use pre-defined constants for masking current value of attributes. Signed-off-by:
Khalid Aziz <khalid.aziz@hp.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Acked-by:
Matthew Garrett <mjg@redhat.com> Signed-off-by:
-
Larry Finger authored
commit 2d838bb6 upstream. When b43legacy is loaded without the firmware being available, a following unload generates a kernel NULL pointer dereference BUG as follows: [ 214.330789] BUG: unable to handle kernel NULL pointer dereference at 0000004c [ 214.330997] IP: [<c104c395>] drain_workqueue+0x15/0x170 [ 214.331179] *pde = 00000000 [ 214.331311] Oops: 0000 [#1] SMP [ 214.331471] Modules linked in: b43legacy(-) ssb pcmcia mac80211 cfg80211 af_packet mperf arc4 ppdev sr_mod cdrom sg shpchp yenta_socket pcmcia_rsrc pci_hotplug pcmcia_core battery parport_pc parport floppy container ac button edd autofs4 ohci_hcd ehci_hcd usbcore usb_common thermal processor scsi_dh_rdac scsi_dh_hp_sw scsi_dh_emc scsi_dh_alua scsi_dh fan thermal_sys hwmon ata_generic pata_ali libata [last unloaded: cfg80211] [ 214.333421] Pid: 3639, comm: modprobe Not tainted 3.6.0-rc6-wl+ #163 Source Technology VIC 9921/ALI Based Notebook [ 214.333580] EIP: 0060:[<c104c395>] EFLAGS: 00010246 CPU: 0 [ 214.333687] EIP is at drain_workqueue+0x15/0x170 [ 214.333788] EAX: c162ac40 EBX: cdfb8360 ECX: 0000002a EDX: 00002a2a [ 214.333890] ESI: 00000000 EDI: 00000000 EBP: cd767e7c ESP: cd767e5c [ 214.333957] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 214.333957] CR0: 8005003b CR2: 0000004c CR3: 0c96a000 CR4: 00000090 [ 214.333957] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000 [ 214.333957] DR6: ffff0ff0 DR7: 00000400 [ 214.333957] Process modprobe (pid: 3639, ti=cd766000 task=cf802e90 task.ti=cd766000) [ 214.333957] Stack: [ 214.333957] 00000292 cd767e74 c12c5e09 00000296 00000296 cdfb8360 cdfb9220 00000000 [ 214.333957] cd767e90 c104c4fd cdfb8360 cdfb9220 cd682800 cd767ea4 d0c10184 cd682800 [ 214.333957] cd767ea4 cba31064 cd767eb8 d0867908 cba31064 d087e09c cd96f034 cd767ec4 [ 214.333957] Call Trace: [ 214.333957] [<c12c5e09>] ? skb_dequeue+0x49/0x60 [ 214.333957] [<c104c4fd>] destroy_workqueue+0xd/0x150 [ 214.333957] [<d0c10184>] ieee80211_unregister_hw+0xc4/0x100 [mac80211] [ 214.333957] [<d0867908>] b43legacy_remove+0x78/0x80 [b43legacy] [ 214.333957] [<d083654d>] ssb_device_remove+0x1d/0x30 [ssb] [ 214.333957] [<c126f15a>] __device_release_driver+0x5a/0xb0 [ 214.333957] [<c126fb07>] driver_detach+0x87/0x90 [ 214.333957] [<c126ef4c>] bus_remove_driver+0x6c/0xe0 [ 214.333957] [<c1270120>] driver_unregister+0x40/0x70 [ 214.333957] [<d083686b>] ssb_driver_unregister+0xb/0x10 [ssb] [ 214.333957] [<d087c488>] b43legacy_exit+0xd/0xf [b43legacy] [ 214.333957] [<c1089dde>] sys_delete_module+0x14e/0x2b0 [ 214.333957] [<c110a4a7>] ? vfs_write+0xf7/0x150 [ 214.333957] [<c1240050>] ? tty_write_lock+0x50/0x50 [ 214.333957] [<c110a6f8>] ? sys_write+0x38/0x70 [ 214.333957] [<c1397c55>] syscall_call+0x7/0xb [ 214.333957] Code: bc 27 00 00 00 00 a1 74 61 56 c1 55 89 e5 e8 a3 fc ff ff 5d c3 90 55 89 e5 57 56 89 c6 53 b8 40 ac 62 c1 83 ec 14 e8 bb b7 34 00 <8b> 46 4c 8d 50 01 85 c0 89 56 4c 75 03 83 0e 40 80 05 40 ac 62 [ 214.333957] EIP: [<c104c395>] drain_workqueue+0x15/0x170 SS:ESP 0068:cd767e5c [ 214.333957] CR2: 000000000000004c [ 214.341110] ---[ end trace c7e90ec026d875a6 ]---Index: wireless-testing/drivers/net/wireless/b43legacy/main.c The problem is fixed by making certain that the ucode pointer is not NULL before deregistering the driver in mac80211. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Flavio Leitner authored
commit 26e8220a upstream. Apparently the same card model has two IDs, so this patch complements the commit 39aced68 adding the missing one. Signed-off-by:
Flavio Leitner <fbl@redhat.com> Signed-off-by:
-
Linus Walleij authored
commit c5dd553b upstream. This works around a few glitches in the ST version of the PL011 serial driver when using very high baud rates, as we do in the Ux500: 3, 3.25, 4 and 4.05 Mbps. Problem Observed/rootcause: When using high baud-rates, and the baudrate*8 is getting close to the provided clock frequency (so a division factor close to 1), when using bursts of characters (so they are abutted), then it seems as if there is not enough time to detect the beginning of the start-bit which is a timing reference for the entire character, and thus the sampling moment of character bits is moving towards the end of each bit, instead of the middle. Fix: Increase slightly the RX baud rate of the UART above the theoretical baudrate by 5%. This will definitely give more margin time to the UART_RX to correctly sample the data at the middle of the bit period. Also fix the ages old copy-paste error in the very stressed comment, it's referencing the registers used in the PL010 driver rather than the PL011 ones. Signed-off-by:
Guillaume Jaunet <guillaume.jaunet@stericsson.com> Signed-off-by:
Christophe Arnal <christophe.arnal@stericsson.com> Signed-off-by:
Matthias Locher <matthias.locher@stericsson.com> Signed-off-by:
Rajanikanth HV <rajanikanth.hv@stericsson.com> Cc: Bibek Basu <bibek.basu@stericsson.com> Cc: Par-Gunnar Hjalmdahl <par-gunnar.hjalmdahl@stericsson.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Jiri Slaby authored
commit ee8b593a upstream. If a user provides a buffer larger than a tty->write_buf chunk and passes '\r' at the end of the buffer, we touch an out-of-bound memory. Add a check there to prevent this. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Samo Pogacnik <samo_pogacnik@t-2.net> Signed-off-by:
-
Stanislav Kozina authored
commit e9490e93 upstream. Change the BUG_ON to WARN_ON and return in case of tty->read_buf==NULL. We want to track a couple of long standing reports of this but at the same time we can avoid killing the box. Signed-off-by:
Stanislav Kozina <skozina@redhat.com> Signed-off-by:
-
Ian Abbott authored
commit c8cad4c8 upstream. When `do_cmd_ioctl()` allocates memory for the kernel copy of a channel list, it frees any previously allocated channel list in `async->cmd.chanlist` and replaces it with the new one. However, if the device is ever removed (or "detached") the cleanup code in `cleanup_device()` in "drivers.c" does not free this memory so it is lost. A sensible place to free the kernel copy of the channel list is in `do_become_nonbusy()` as at that point the comedi asynchronous command associated with the channel list is no longer valid. Free the channel list in `do_become_nonbusy()` instead of `do_cmd_ioctl()` and clear the pointer to prevent it being freed more than once. Note that `cleanup_device()` could be called at an inappropriate time while the comedi device is open, but that's a separate bug not related to this this patch. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Ian Abbott authored
commit 5d06e3df upstream. `parse_insn()` is dereferencing the user-space pointer `insn->data` directly when handling the `INSN_INTTRIG` comedi instruction. It shouldn't be using `insn->data` at all; it should be using the separate `data` pointer passed to the function. Fix it. Signed-off-by:
-
Ian Abbott authored
commit e1878957 upstream. Correct a direct dereference of I/O memory to use an appropriate I/O memory access function. Note that the pointer being dereferenced is not currently tagged with `__iomem` but I plan to correct that for 3.7. Signed-off-by:
-
Ian Abbott authored
commit b655c2c4 upstream. `s626_enc_insn_config()` is incorrectly dereferencing `insn->data` which is a pointer to user memory. It should be dereferencing the separate `data` parameter that points to a copy of the data in kernel memory. Signed-off-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by:
-
Ben Hutchings authored
commit 40fe4f89 upstream. softsynth_read() reads a character at a time from the init string; when it finds the null terminator it sets the initialized flag but then repeats the last character. Additionally, if the read() buffer is not big enough for the init string, the next read() will start reading from the beginning again. So the caller may never progress to reading anything else. Replace the simple initialized flag with the current position in the init string, carried over between calls. Switch to reading real data once this reaches the null terminator. (This assumes that the length of the init string can't change, which seems to be the case. Really, the string and position belong together in a per-file private struct.) Tested-by:
Samuel Thibault <sthibault@debian.org> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Bjørn Mork authored
commit c638eb28 upstream. The three Pantech devices UML190 (106c:3716), UML290 (106c:3718) and P4200 (106c:3721) all use the same subclasses to identify vendor specific functions. Replace the existing device specific entries with generic vendor matching, adding support for the P4200. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Cc: Thomas Schäfer <tschaefer@t-online.de> Acked-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Antonio Ospite authored
commit 54575b05 upstream. TIAO/DIYGADGET USB Multi-Protocol Adapter (TUMPA) is an FTDI FT2232H based device which provides an easily accessible JTAG, SPI, I2C, serial breakout. http://www.diygadget.com/tiao-usb-multi-protocol-adapter-jtag-spi-i2c-serial.html http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User%27s_Manual FTDI FT2232H provides two serial channels (A and B), but on the TUMPA channel A is dedicated to JTAG/SPI while channel B can be used for UART/RS-232: use the ftdi_jtag_quirk to expose only channel B as a usb-serial interface to userspace. Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Signed-off-by:
-
Bjørn Mork authored
commit 160c9425 upstream. Interface #5 on ZTE MF683 is a QMI/wwan interface. Signed-off-by:
-
Mike Snitzer authored
commit ba1cbad9 upstream. The access beyond the end of device BUG_ON that was introduced to dm_request_fn via commit 29e4013d ("dm: implement REQ_FLUSH/FUA support for request-based dm") was an overly drastic (but simple) response to this situation. I have received a report that this BUG_ON was hit and now think it would be better to use dm_kill_unmapped_request() to fail the clone and original request with -EIO. map_request() will assign the valid target returned by dm_table_find_target to tio->ti. But when the target isn't valid tio->ti is never assigned (because map_request isn't called); so add a check for tio->ti != NULL to dm_done(). Reported-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by:
Alasdair G Kergon <agk@redhat.com> Signed-off-by:
-
Miklos Szeredi authored
commit 8110e16d upstream. IBM reported a deadlock in select_parent(). This was found to be caused by taking rename_lock when already locked when restarting the tree traversal. There are two cases when the traversal needs to be restarted: 1) concurrent d_move(); this can only happen when not already locked, since taking rename_lock protects against concurrent d_move(). 2) racing with final d_put() on child just at the moment of ascending to parent; rename_lock doesn't protect against this rare race, so it can happen when already locked. Because of case 2, we need to be able to handle restarting the traversal when rename_lock is already held. This patch fixes all three callers of try_to_ascend(). IBM reported that the deadlock is gone with this patch. [ I rewrote the patch to be smaller and just do the "goto again" if the lock was already held, but credit goes to Miklos for the real work. - Linus ] Signed-off-by:
Miklos Szeredi <mszeredi@suse.cz> Cc: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
- 02 Oct, 2012 22 commits
-
-
Greg Kroah-Hartman authored
-
Will Deacon authored
commit a76d7bd9 upstream. The open-coded mutex implementation for ARMv6+ cores suffers from a severe lack of barriers, so in the uncontended case we don't actually protect any accesses performed during the critical section. Furthermore, the code is largely a duplication of the ARMv6+ atomic_dec code but optimised to remove a branch instruction, as the mutex fastpath was previously inlined. Now that this is executed out-of-line, we can reuse the atomic access code for the locking (in fact, we use the xchg code as this produces shorter critical sections). This patch uses the generic xchg based implementation for mutexes on ARMv6+, which introduces barriers to the lock/unlock operations and also has the benefit of removing a fair amount of inline assembly code. Acked-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Nicolas Pitre <nico@linaro.org> Reported-by:
Shan Kang <kangshan0910@gmail.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Alan Stern authored
commit 0d00dc26 upstream. This patch (as1607) fixes a race that can occur if a USB host controller is removed while a process is reading the /sys/kernel/debug/usb/devices file. The usb_device_read() routine uses the bus->root_hub pointer to determine whether or not the root hub is registered. The is not a valid test, because the pointer is set before the root hub gets registered and remains set even after the root hub is unregistered and deallocated. As a result, usb_device_read() or usb_device_dump() can access freed memory, causing an oops. The patch changes the test to use the hcd->rh_registered flag, which does get set and cleared at the appropriate times. It also makes sure to hold the usb_bus_list_lock mutex while setting the flag, so that usb_device_read() will become aware of new root hubs as soon as they are registered. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Don Zickus <dzickus@redhat.com> Signed-off-by:
-
Andi Kleen authored
commit a129a7c8 upstream. When running on 32bit the mce handler could misinterpret vm86 mode as ring 0. This can affect whether it does recovery or not; it was possible to panic when recovery was actually possible. Fix this by always forcing vm86 to look like ring 3. [ Backport to 3.0 notes: Things changed there slightly: - move mce_get_rip() up. It fills up m->cs and m->ip values which are evaluated in mce_severity(). Therefore move it up right before the mce_severity call. This seem to be another bug in 3.0? - Place the backport (fix m->cs in V86 case) to where m->cs gets filled which is mce_get_rip() in 3.0 ] Signed-off-by:
Andi Kleen <ak@linux.intel.com> Signed-off-by:
Tony Luck <tony.luck@intel.com> Signed-off-by:
Thomas Renninger <trenn@suse.de> Reviewed-by:
-
Yasunori Goto authored
commit b5740f4b upstream. try_to_wake_up() has a problem which may change status from TASK_DEAD to TASK_RUNNING in race condition with SMI or guest environment of virtual machine. As a result, exited task is scheduled() again and panic occurs. Here is the sequence how it occurs: ----------------------------------+----------------------------- | CPU A | CPU B ----------------------------------+----------------------------- TASK A calls exit().... do_exit() exit_mm() down_read(mm->mmap_sem); rwsem_down_failed_common() set TASK_UNINTERRUPTIBLE set waiter.task <= task A list_add to sem->wait_list : raw_spin_unlock_irq() (I/O interruption occured) __rwsem_do_wake(mmap_sem) list_del(&waiter->list); waiter->task = NULL wake_up_process(task A) try_to_wake_up() (task is still TASK_UNINTERRUPTIBLE) p->on_rq is still 1.) ttwu_do_wakeup() (*A) : (I/O interruption handler finished) if (!waiter.task) schedule() is not called due to waiter.task is NULL. tsk->state = TASK_RUNNING : check_preempt_curr(); : task->state = TASK_DEAD (*B) <--- set TASK_RUNNING (*C) schedule() (exit task is running again) BUG_ON() is called! -------------------------------------------------------- The execution time between (*A) and (*B) is usually very short, because the interruption is disabled, and setting TASK_RUNNING at (*C) must be executed before setting TASK_DEAD. HOWEVER, if SMI is interrupted between (*A) and (*B), (*C) is able to execute AFTER setting TASK_DEAD! Then, exited task is scheduled again, and BUG_ON() is called.... If the system works on guest system of virtual machine, the time between (*A) and (*B) may be also long due to scheduling of hypervisor, and same phenomenon can occur. By this patch, do_exit() waits for releasing task->pi_lock which is used in try_to_wake_up(). It guarantees the task becomes TASK_DEAD after waking up. Signed-off-by:
Yasunori Goto <y-goto@jp.fujitsu.com> Acked-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Link: http://lkml.kernel.org/r/20120117174031.3118.E1E9C6FF@jp.fujitsu.comSigned-off-by:
Ingo Molnar <mingo@elte.hu> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by:
-
Herton Ronaldo Krzesinski authored
commit 067aa481 upstream. Commit 178db7d3, "spi: Fix device unregistration when unregistering the bus master", changed spi device initialization of dev.parent pointer to be the master's device pointer instead of his parent. This introduced a bug in spi-fsl-spi, since its usage of spi device pointer was not updated accordingly. This was later fixed by commit 5039a869, "spi/mpc83xx: fix NULL pdata dereference bug", but it missed another spot on fsl_spi_cs_control function where we also need to update usage of spi device pointer. This change address that. Signed-off-by:
Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Acked-by:
Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by:
Grant Likely <grant.likely@secretlab.ca> Cc: Alfredo Capella <alfredo.capella@gmail.com> Signed-off-by:
-
Kenth Eriksson authored
commit 5039a869 upstream. Commit 178db7d3, "spi: Fix device unregistration when unregistering the bus master", changed device initialization to be children of the bus master, not children of the bus masters parent device. The pdata pointer used in fsl_spi_chipselect must updated to reflect the changed initialization. Signed-off-by:
Kenth Eriksson <kenth.eriksson@transmode.com> Acked-by:
-
Artem Bityutskiy authored
commit 78b495c3 upstream UBI was mistakingly using 'kfree()' instead of 'kmem_cache_free()' when freeing "attach eraseblock" structures in vtbl.c. Thankfully, this happened only when we were doing auto-format, so many systems were unaffected. However, there are still many users affected. It is strange, but the system did not crash and nothing bad happened when the SLUB memory allocator was used. However, in case of SLOB we observed an crash right away. This problem was introduced in 2.6.39 by commit "6c1e875c UBI: add slab cache for ubi_scan_leb objects" Reported-by:
Richard Genoud <richard.genoud@gmail.com> Signed-off-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by:
-
Chris Boot authored
commit d4a4206e upstream. ASPM on the 82574 causes trouble. Currently the driver disables L0s for this NIC but only disables L1 if the MTU is >1500. This patch simply causes L1 to be disabled regardless of the MTU setting. Signed-off-by:
Chris Boot <bootc@bootc.net> Cc: "Wyborny, Carolyn" <carolyn.wyborny@intel.com> Cc: Nix <nix@esperi.org.uk> Link: https://lkml.org/lkml/2012/3/19/362Tested-by:
Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by:
-
Al Cooper authored
commit 4188bba0 upstream. The driver should not try to switch to 1.8V when the SD 3.0 host controller does not have any UHS capabilities bits set (SDR50, DDR50 or SDR104). See page 72 of "SD Specifications Part A2 SD Host Controller Simplified Specification Version 3.00" under "1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host capabilities data structure for all V3.0 host controllers, only set them if SDR104, SDR50 or DDR50 is set in the host capabilities register. This will prevent the switch to 1.8V later. Signed-off-by:
Al Cooper <acooper@gmail.com> Acked-by:
Arindam Nath <arindam.nath@amd.com> Acked-by:
Philip Rakity <prakity@marvell.com> Acked-by:
Girish K S <girish.shivananjappa@linaro.org> Signed-off-by:
Chris Ball <cjb@laptop.org> Signed-off-by:
-
Subhash Jadavani authored
commit f2815f68 upstream. Here is Essential conditions to indicate Version 3.00 Card (SD_SPEC=2 and SD_SPEC3=1) : (1) The card shall support CMD6 (2) The card shall support CMD8 (3) The card shall support CMD42 (4) User area capacity shall be up to 2GB (SDSC) or 32GB (SDHC) User area capacity shall be more than or equal to 32GB and up to 2TB (SDXC) (5) Speed Class shall be supported (SDHC or SDXC) So even if SD card doesn't support any of the newly defined UHS-I bus speed mode, it can advertise itself as SD3.0 cards as long as it supports all the essential conditions of SD3.0 cards. Given this, these type of cards should atleast run in High Speed mode @50MHZ if it supports HS. But current initialization sequence for SD3.0 cards is such that these non-UHS-I SD3.0 cards runs in Default Speed mode @25MHz. This patch makes sure that these non-UHS-I SD3.0 cards run in High Speed Mode @50MHz. Tested this patch with SanDisk Extreme SDHC 8GB Class 10 card. Reported-by:
"Hiremath, Vaibhav" <hvaibhav@ti.com> Signed-off-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
-
Phillip Lougher authored
commit cc37f75a upstream. A Squashfs filesystem containing nothing but an empty directory, although unusual and ultimately pointless, is still valid. The directory_table >= next_table sanity check rejects these filesystems as invalid because the directory_table is empty and equal to next_table. Signed-off-by:
Phillip Lougher <phillip@squashfs.org.uk> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Tomoya MORINAGA authored
commit 38bd2a1a upstream. Parity Setting value is reverse. E.G. In case of setting ODD parity, EVEN value is set. This patch inverts "if" condition. Signed-off-by:
Tomoya MORINAGA <tomoya.rohm@gmail.com> Acked-by:
-
Tomoya MORINAGA authored
commit 9539dfb7 upstream. Rx Error interrupt(E.G. parity error) is not enabled. So, when parity error occurs, error interrupt is not occurred. As a result, the received data is not dropped. This patch adds enable/disable rx error interrupt code. Signed-off-by:
-
Alan Cox authored
commit 9bc03743 upstream. Otherwise we fall back to the wrong value. Reported-by: <dcb314@hotmail.com> Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44091Signed-off-by:
-
Douglas Bagnall authored
commit 720bb643 upstream. For some reason, when the lirc daemon learns that a usb remote control has been unplugged, it wants to read the sysfs attributes of the disappearing device. This is useful for uncovering transient inconsistencies, but less so for keeping the system running when such inconsistencies exist. Under some circumstances (like every time I unplug my dvb stick from my laptop), lirc catches an rc_dev whose raw event handler has been removed (presumably by ir_raw_event_unregister), and proceeds to interrogate the raw protocols supported by the NULL pointer. This patch avoids the NULL dereference, and ignores the issue of how this state of affairs came about in the first place. Version 2 incorporates changes recommended by Mauro Carvalho Chehab (-ENODEV instead of -EINVAL, and a signed-off-by). Signed-off-by:
Douglas Bagnall <douglas@paradise.net.nz> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com> Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by:
-
John Stultz authored
commit cee58483 upstream Andreas Bombe reported that the added ktime_t overflow checking added to timespec_valid in commit 4e8b1452 ("time: Improve sanity checking of timekeeping inputs") was causing problems with X.org because it caused timeouts larger then KTIME_T to be invalid. Previously, these large timeouts would be clamped to KTIME_MAX and would never expire, which is valid. This patch splits the ktime_t overflow checking into a new timespec_valid_strict function, and converts the timekeeping codes internal checking to use this more strict function. Reported-and-tested-by:
Andreas Bombe <aeb@debian.org> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
-
John Stultz authored
commit bf2ac312 upstream If update_wall_time() is called and the current offset isn't large enough to accumulate, avoid re-calling timekeeping_adjust which may change the clock freq and can cause 1ns inconsistencies with CLOCK_REALTIME_COARSE/CLOCK_MONOTONIC_COARSE. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
John Stultz authored
commit 4e8b1452 upstream Unexpected behavior could occur if the time is set to a value large enough to overflow a 64bit ktime_t (which is something larger then the year 2262). Also unexpected behavior could occur if large negative offsets are injected via adjtimex. So this patch improves the sanity check timekeeping inputs by improving the timespec_valid() check, and then makes better use of timespec_valid() to make sure we don't set the time to an invalid negative value or one that overflows ktime_t. Note: This does not protect from setting the time close to overflowing ktime_t and then letting natural accumulation cause the overflow. Reported-by:
CAI Qian <caiqian@redhat.com> Reported-by:
Sasha Levin <levinsasha928@gmail.com> Signed-off-by:
-
Eric Dumazet authored
commit bec4596b upstream. drop_monitor calls several sleeping functions while in atomic context. BUG: sleeping function called from invalid context at mm/slub.c:943 in_atomic(): 1, irqs_disabled(): 0, pid: 2103, name: kworker/0:2 Pid: 2103, comm: kworker/0:2 Not tainted 3.5.0-rc1+ #55 Call Trace: [<ffffffff810697ca>] __might_sleep+0xca/0xf0 [<ffffffff811345a3>] kmem_cache_alloc_node+0x1b3/0x1c0 [<ffffffff8105578c>] ? queue_delayed_work_on+0x11c/0x130 [<ffffffff815343fb>] __alloc_skb+0x4b/0x230 [<ffffffffa00b0360>] ? reset_per_cpu_data+0x160/0x160 [drop_monitor] [<ffffffffa00b022f>] reset_per_cpu_data+0x2f/0x160 [drop_monitor] [<ffffffffa00b03ab>] send_dm_alert+0x4b/0xb0 [drop_monitor] [<ffffffff810568e0>] process_one_work+0x130/0x4c0 [<ffffffff81058249>] worker_thread+0x159/0x360 [<ffffffff810580f0>] ? manage_workers.isra.27+0x240/0x240 [<ffffffff8105d403>] kthread+0x93/0xa0 [<ffffffff816be6d4>] kernel_thread_helper+0x4/0x10 [<ffffffff8105d370>] ? kthread_freezable_should_stop+0x80/0x80 [<ffffffff816be6d0>] ? gs_change+0xb/0xb Rework the logic to call the sleeping functions in right context. Use standard timer/workqueue api to let system chose any cpu to perform the allocation and netlink send. Also avoid a loop if reset_per_cpu_data() cannot allocate memory : use mod_timer() to wait 1/10 second before next try. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Neil Horman <nhorman@tuxdriver.com> Reviewed-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Neil Horman authored
commit 4fdcfa12 upstream. I just noticed after some recent updates, that the init path for the drop monitor protocol has a minor error. drop monitor maintains a per cpu structure, that gets initalized from a single cpu. Normally this is fine, as the protocol isn't in use yet, but I recently made a change that causes a failed skb allocation to reschedule itself . Given the current code, the implication is that this workqueue reschedule will take place on the wrong cpu. If drop monitor is used early during the boot process, its possible that two cpus will access a single per-cpu structure in parallel, possibly leading to data corruption. This patch fixes the situation, by storing the cpu number that a given instance of this per-cpu data should be accessed from. In the case of a need for a reschedule, the cpu stored in the struct is assigned the rescheule, rather than the currently executing cpu Tested successfully by myself. Signed-off-by:
-
Neil Horman authored
commit 3885ca78 upstream. Eric Dumazet pointed out to me that the drop_monitor protocol has some holes in its smp protections. Specifically, its possible to replace data->skb while its being written. This patch corrects that by making data->skb an rcu protected variable. That will prevent it from being overwritten while a tracepoint is modifying it. Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> CC: David Miller <davem@davemloft.net> Acked-by:
-
