- 04 Sep, 2019 28 commits
-
-
The j1939 authors authored
SAE J1939 is the vehicle bus recommended practice used for communication and diagnostics among vehicle components. Originating in the car and heavy-duty truck industry in the United States, it is now widely used in other parts of the world. J1939, ISO 11783 and NMEA 2000 all share the same high level protocol. SAE J1939 can be considered the replacement for the older SAE J1708 and SAE J1587 specifications. Acked-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Bastian Stender <bst@pengutronix.de> Signed-off-by:
Elenita Hinds <ecathinds@gmail.com> Signed-off-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be> Signed-off-by:
Maxime Jayat <maxime.jayat@mobile-devices.fr> Signed-off-by:
Robin van der Gracht <robin@protonic.nl> Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Kurt Van Dijck authored
This patch prepares struct sockaddr_can for SAE J1939. Signed-off-by:
-
Kurt Van Dijck authored
This patch is a preparation for SAE J1939 and adds CAN_J1939 socket type. Signed-off-by:
-
Kurt Van Dijck authored
The size of this structure will be increased with J1939 support. To stay binary compatible, the CAN_REQUIRED_SIZE macro is introduced for existing CAN protocols. Signed-off-by:
-
Kurt Van Dijck authored
This commit replaces my company's email address with a stable private address. Signed-off-by:
-
Oleksij Rempel authored
The can_rx_unregister() can be called from NAPI (soft IRQ) context, at least by j1939 stack. This leads to potential dead lock with &net->can.rcvlists_lock called from can_rx_register: =============================================================================== WARNING: inconsistent lock state 4.19.0-20181029-1-g3e67f95ba0d3 #3 Not tainted -------------------------------- inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. testj1939/224 [HC0[0]:SC1[1]:HE1:SE0] takes: 1ad0fda3 (&(&net->can.rcvlists_lock)->rlock){+.?.}, at: can_rx_unregister+0x4c/0x1ac {SOFTIRQ-ON-W} state was registered at: lock_acquire+0xd0/0x1f4 _raw_spin_lock+0x30/0x40 can_rx_register+0x5c/0x14c j1939_netdev_start+0xdc/0x1f8 j1939_sk_bind+0x18c/0x1c8 __sys_bind+0x70/0xb0 sys_bind+0x10/0x14 ret_fast_syscall+0x0/0x28 0xbedc9b64 irq event stamp: 2440 hardirqs last enabled at (2440): [<c01302c0>] __local_bh_enable_ip+0xac/0x184 hardirqs last disabled at (2439): [<c0130274>] __local_bh_enable_ip+0x60/0x184 softirqs last enabled at (2412): [<c08b0bf4>] release_sock+0x84/0xa4 softirqs last disabled at (2415): [<c013055c>] irq_exit+0x100/0x1b0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(&net->can.rcvlists_lock)->rlock); <Interrupt> lock(&(&net->can.rcvlists_lock)->rlock); *** DEADLOCK *** 2 locks held by testj1939/224: #0: 168eb13b (rcu_read_lock){....}, at: netif_receive_skb_internal+0x3c/0x350 #1: 168eb13b (rcu_read_lock){....}, at: can_receive+0x88/0x1c0 =============================================================================== To avoid this situation, we should use spin_lock_bh() instead of spin_lock(). Signed-off-by: -
Marc Kleine-Budde authored
Since using the "struct can_ml_priv" for the per device "struct dev_rcv_lists" the call can_dev_rcv_lists_find() cannot fail anymore. This patch simplifies af_can by removing the NULL pointer checks from the dev_rcv_lists returned by can_dev_rcv_lists_find(). Signed-off-by:
-
Marc Kleine-Budde authored
This patch removes the old method of allocating the per device protocol specific memory via a netdevice_notifier. This had the drawback, that the allocation can fail, leading to a lot of null pointer checks in the code. This also makes the live cycle management of this memory quite complicated. This patch switches from the allocating the struct can_dev_rcv_lists in a NETDEV_REGISTER call to using the dev->ml_priv, which is allocated by the driver since the previous patch. Signed-off-by:
-
Marc Kleine-Budde authored
This patch introduces the CAN midlayer private structure ("struct can_ml_priv") which should be used to hold protocol specific per device data structures. For now it's only member is "struct can_dev_rcv_lists". The CAN midlayer private is allocated via alloc_netdev()'s private and assigned to "struct net_device::ml_priv" during device creation. This is done transparently for CAN drivers using alloc_candev(). The slcan, vcan and vxcan drivers which are not using alloc_candev() have been adopted manually. The memory layout of the netdev_priv allocated via alloc_candev() will looke like this: +-------------------------+ | driver's priv | +-------------------------+ | struct can_ml_priv | +-------------------------+ | array of struct sk_buff | +-------------------------+ Signed-off-by: -
Marc Kleine-Budde authored
The networking core takes care and unregisters every network device in a namespace before calling the can_pernet_exit() hook. This patch removes the unneeded cleanup. Acked-by:
Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by:
-
Marc Kleine-Budde authored
This patch replaces an open coded max by the proper kernel define max(). Acked-by:
-
Marc Kleine-Budde authored
This patch gives the variables holding the CAN receiver and the receiver list a better name by renaming them from "r to "rcv" and "rl" to "recv_list". Signed-off-by:
-
Marc Kleine-Budde authored
This patch add the commonly used prefix "can_" to the find_dev_rcv_lists() function and moves the "find" to the end, as the function returns a struct can_dev_rcv_list. This improves the overall readability of the code. Signed-off-by:
-
Marc Kleine-Budde authored
This patch add the commonly used prefix "can_" to the find_rcv_list() function and add the "find" to the end, as the function returns a struct rcv_list. This improves the overall readability of the code. Signed-off-by:
-
Marc Kleine-Budde authored
This patch gives the variables holding the CAN per device receive filter lists a better name by renaming them from "d" to "dev_rcv_lists". Signed-off-by:
-
Marc Kleine-Budde authored
This patch gives the variables holding the CAN receive filter lists a better name by renaming them from "d" to "dev_rcv_lists". Signed-off-by:
-
Marc Kleine-Budde authored
This patch improves the code reability by removing the redundant "can_" prefix from the members of struct netns_can (as the struct netns_can itself is the member "can" of the struct net.) The conversion is done with: sed -i \ -e "s/struct can_dev_rcv_lists \*can_rx_alldev_list;/struct can_dev_rcv_lists *rx_alldev_list;/" \ -e "s/spinlock_t can_rcvlists_lock;/spinlock_t rcvlists_lock;/" \ -e "s/struct timer_list can_stattimer;/struct timer_list stattimer; /" \ -e "s/can\.can_rx_alldev_list/can.rx_alldev_list/g" \ -e "s/can\.can_rcvlists_lock/can.rcvlists_lock/g" \ -e "s/can\.can_stattimer/can.stattimer/g" \ include/net/netns/can.h \ net/can/*.[ch] Signed-off-by:
-
Marc Kleine-Budde authored
This patch rename the variables holding the CAN statistics (can_stats and can_pstats) to pkg_stats and rcv_lists_stats which reflect better their meaning. The conversion is done with: sed -i \ -e "s/can_stats\([^_]\)/pkg_stats\1/g" \ -e "s/can_pstats/rcv_lists_stats/g" \ net/can/proc.c Signed-off-by:
-
Marc Kleine-Budde authored
This patch rename the variables holding the CAN statistics (can_stats and can_pstats) to pkg_stats and rcv_lists_stats which reflect better their meaning. The conversion is done with: sed -i \ -e "s/can_stats\([^_]\)/pkg_stats\1/g" \ -e "s/can_pstats/rcv_lists_stats/g" \ net/can/af_can.c Signed-off-by:
-
Marc Kleine-Budde authored
This patch gives the members of the struct netns_can that are holding the statistics a sensible name, by renaming struct netns_can::can_stats into struct netns_can::pkg_stats and struct netns_can::can_pstats into struct netns_can::rcv_lists_stats. The conversion is done with: sed -i \ -e "s:\(struct[^*]*\*\)can_stats;.*:\1pkg_stats;:" \ -e "s:\(struct[^*]*\*\)can_pstats;.*:\1rcv_lists_stats;:" \ -e "s/can\.can_stats/can.pkg_stats/g" \ -e "s/can\.can_pstats/can.rcv_lists_stats/g" \ net/can/*.[ch] \ include/net/netns/can.h Signed-off-by:
-
Marc Kleine-Budde authored
This patch renames both "struct s_stats" and "struct s_pstats", to "struct can_pkg_stats" and "struct can_rcv_lists_stats" to better reflect their meaning and improve code readability. The conversion is done with: sed -i \ -e "s/struct s_stats/struct can_pkg_stats/g" \ -e "s/struct s_pstats/struct can_rcv_lists_stats/g" \ net/can/*.[ch] \ include/net/netns/can.h Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 100GbE Intel Wired LAN Driver Updates 2019-09-03 This series contains updates to ice driver only. Anirudh adds the ability for the driver to handle EMP resets correctly by adding the logic to the existing ice_reset_subtask(). Jeb fixes up the logic to properly free up the resources for a switch rule whether or not it was successful in the removal. Brett fixes up the reporting of ITR values to let the user know odd ITR values are not allowed. Fixes the driver to only disable VLAN pruning on VLAN deletion when the VLAN being deleted is the last VLAN on the VF VSI. Chinh updates the driver to determine the TSA value from the priority value when in CEE mode. Bruce aligns the driver with the hardware specification by ensuring that a PF reset is done as part of the unload logic. Also update the driver unloading field, based on the latest hardware specification, which allows us to remove an unnecessary endian conversion. Moves #defines based on their need in the code. Jesse adds the current state of auto-negotiation in the link up message. In addition, adds additional information to inform the user of an issue with the topology/configuration of the link. Usha updates the driver to allow the maximum TCs that the firmware supports, rather than hard coding to a set value. Dave updates the DCB initialization flow to handle the case of an actual error during DCB init. Updated the driver to report the current stats, even when the netdev is down, which aligns with our other drivers. Mitch fixes the VF reset code flows to ensure that it properly calls ice_dis_vsi_txq() to notify the firmware that the VF is being reset. Michal fixes the driver so the DCB is not enabled when the SW LLDP is activated, which was causing a communication issue with other NICs. The problem lies in that DCB was being enabled without checking the number of TCs. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-updates-2019-09-01 (Software steering support) Abstract: -------- Mellanox ConnetX devices supports packet matching, packet modification and redirection. These functionalities are also referred to as flow-steering. To configure a steering rule, the rule is written to the device owned memory, this memory is accessed and cached by the device when processing a packet. Steering rules are constructed from multiple steering entries (STE). Rules are configured using the Firmware command interface. The Firmware processes the given driver command and translates them to STEs, then writes them to the device memory in the current steering tables. This process is slow due to the architecture of the command interface and the processing complexity of each rule. The highlight of this patchset is to cut the middle man (The firmware) and do steering rules programming into device directly from the driver, with no firmware intervention whatsoever. Motivation: ----------- Software (driver managed) steering allows for high rule insertion rates compared to the FW steering described above, this is achieved by using internal RDMA writes to the device owned memory instead of the slow command interface to program steering rules. Software (driver managed) steering, doesn't depend on new FW for new steering functionality, new implementations can be done in the driver skipping the FW layer. Performance: ------------ The insertion rate on a single core using the new approach allows programming ~300K rules per sec. (Done via direct raw test to the new mlx5 sw steering layer, without any kernel layer involved). Test: TC L2 rules 33K/s with Software steering (this patchset). 5K/s with FW and current driver. This will improve OVS based solution performance. Architecture and implementation details: ---------------------------------------- Software steering will be dynamically selected via devlink device parameter. Example: $ devlink dev param show pci/0000:06:00.0 name flow_steering_mode pci/0000:06:00.0: name flow_steering_mode type driver-specific values: cmode runtime value smfs mlx5 software steering module a.k.a (DR - Direct Rule) is implemented and contained in mlx5/core/steering directory and controlled by MLX5_SW_STEERING kconfig flag. mlx5 core steering layer (fs_core) already provides a shim layer for implementing different steering mechanisms, software steering will leverage that as seen at the end of this series. When Software Steering for a specific steering domain (NIC/RDMA/Vport/ESwitch, etc ..) is supported, it will cause rules targeting this domain to be created using SW steering instead of FW. The implementation includes: Domain - The steering domain is the object that all other object resides in. It holds the memory allocator, send engine, locks and other shared data needed by lower objects such as table, matcher, rule, action. Each domain can contain multiple tables. Domain is equivalent to namespaces e.g (NIC/RDMA/Vport/ESwitch, etc ..) as implemented currently in mlx5_core fs_core (flow steering core). Table - Table objects are used for holding multiple matchers, each table has a level used to prevent processing loops. Packets are being directed to this table once it is set as the root table, this is done by fs_core using a FW command. A packet is being processed inside the table matcher by matcher until a successful hit, otherwise the packet will perform the default action. Matcher - Matchers objects are used to specify the fields mask for matching when processing a packet. A matcher belongs to a table, each matcher can hold multiple rules, each rule with different matching values corresponding to the matcher mask. Each matcher has a priority used for rule processing order inside the table. Action - Action objects are created to specify different steering actions such as count, reformat (encapsulate, decapsulate, ...), modify header, forward to table and many other actions. When creating a rule a sequence of actions can be provided to be executed on a successful match. Rule - Rule objects are used to specify a specific match on packets as well as the actions that should be executed. A rule belongs to a matcher. STE - This layer is used to hold the specific STE format for the device and to convert the requested rule to STEs. Each rule is constructed of an STE chain, Multiple rules construct a steering graph. Each node in the graph is a hash table containing multiple STEs. The index of each STE in the hash table is being calculated using a CRC32 hash function. Memory pool - Used for managing and caching device owned memory for rule insertion. The memory is being allocated using DM (device memory) API. Communication with device - layer for standard RDMA operation using RC QP to configure the device steering. Command utility - This module holds all of the FW commands that are required for SW steering to function. Patch planning and files: ------------------------- 1) First patch, adds the support to Add flow steering actions to fs_cmd shim layer. 2) Next 12 patch will add a file per each Software steering functionality/module as described above. (See patches with title: DR, *) 3) Add CONFIG_MLX5_SW_STEERING for software steering support and enable build with the new files 4) Next two patches will add the support for software steering in mlx5 steering shim layer net/mlx5: Add API to set the namespace steering mode net/mlx5: Add direct rule fs_cmd implementation 5) Last two patches will add the new devlink parameter to select mlx5 steering mode, will be valid only for switchdev mode for now. Two modes are supported: 1. DMFS - Device managed flow steering 2. SMFS - Software/Driver managed flow steering. In the DMFS mode, the HW steering entities are created through the FW. In the SMFS mode this entities are created though the driver directly. The driver will use the devlink steering mode only if the steering domain supports it, for now SMFS will manages only the switchdev eswitch steering domain. User command examples: - Set SMFS flow steering mode:: $ devlink dev param set pci/0000:06:00.0 name flow_steering_mode value "smfs" cmode runtime - Read device flow steering mode:: $ devlink dev param show pci/0000:06:00.0 name flow_steering_mode pci/0000:06:00.0: name flow_steering_mode type driver-specific values: cmode runtime value smfs ==================== Signed-off-by: -
Brett Creeley authored
Currently if the VF adds a VLAN, VLAN pruning will be enabled for that VSI. Also, when a VLAN gets deleted it will disable VLAN pruning even if other VLAN(s) exists for the VF. Fix this by only disabling VLAN pruning on the VF VSI when removing the last VF (i.e. vf->num_vlan == 0). Signed-off-by:
Brett Creeley <brett.creeley@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Michal Swiatkowski authored
Remove code that enables DCB in initialization when SW LLDP is activated. DCB flag is set or reset before in ice_init_pf_dcb based on number of TCs. So there is not need to overwrite it. Setting DCB without checking number of TCs can cause communication problems with other cards. Host card sends packet with VLAN priority tag, but client card doesn't strip this tag and ping doesn't work. Signed-off-by:
Michal Swiatkowski <michal.swiatkowski@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by:
-
Dave Ertman authored
There is currently a check in get_ndo_stats that returns before updating stats if the VSI is down or there are no Tx or Rx queues. This causes the netdev to report zero stats with the netdev is down. Remove the check so that the behavior of reporting stats is the same as it was in IXGBE. Signed-off-by:
Dave Ertman <david.m.ertman@intel.com> Tested-by:
-
Mitch Williams authored
The call to ice_dis_vsi_txq() acts as the notification to the firmware that the VF is being reset. Because of this, we need to make this call every time we reset, regardless of whatever else we do to stop the Tx queues. Without this change, VF resets would fail to complete on interfaces that were up and running. Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Tested-by:
-
Dave Ertman authored
In the init path for DCB, the call to ice_init_dcb() can return a non-zero value for either an actual error, or due to the FW lldp engine being stopped. We are currently treating all non-zero values only as an indication that the FW LLDP engine is stopped. Check for an actual error in the DCB init flow. Signed-off-by:
-
- 03 Sep, 2019 12 commits
-
-
Usha Ketineni authored
This patch limits the max TCs set by the driver to the value provided by the firmware as per the capabilities of the device. Otherwise, hard coding to 8 TC max would fail the device configurations with more than 4 ports. Signed-off-by:
Usha Ketineni <usha.k.ketineni@intel.com> Signed-off-by:
-
Tony Nguyen authored
Conventionally, if the #defines/other are not needed by other header files being included, #includes are done first followed by #defines and other stuff. Move the #defines before the #includes to follow this convention. Suggested by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by:
-
Jesse Brandeburg authored
The driver needs to inform the user if there is an issue with the topology / configuration of the link. Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
-
Jesse Brandeburg authored
Print the state of auto-negotiation when printing the Link up message. Adds new text to the "NIC Link is up" line like Autoneg: <True | False> Signed-off-by:
-
Bruce Allan authored
According to recent specification versions, the field in the Queue Shutdown AdminQ command consisting of the "driver unloading" indication is not a 4 byte field (it is byte.bit 16.0). Change it to a byte and remove the unnecessary endian conversion. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Tested-by:
-
Bruce Allan authored
According to the specification, a PF Reset must be done as part of the driver unload flow. Signed-off-by:
-
Chinh T Cao authored
In CEE mode, the TSA information can be derived from the reported priority value. Signed-off-by:
Chinh T Cao <chinh.t.cao@intel.com> Tested-by:
-
Brett Creeley authored
Currently if the user sets an odd value for [tx|rx]-usecs we align the value because the hardware only understands ITR values in multiples of 2. This seems misleading because we are essentially telling the user that the ITR value is odd, when in fact we have changed it internally. Fix this by reporting that setting odd ITR values is not allowed. Also, while making changes to ice_set_rc_coalesce() I noticed a bit of code/error duplication. Make the necessary changes to remove the duplication. Signed-off-by:
-
Jeb Cramer authored
We don't free s_rule if ice_aq_sw_rules() returns a non-zero status. If it returned a zero status, s_rule would be freed right after, so this implies it should be freed within the scope of the function regardless. Signed-off-by:
Jeb Cramer <jeb.j.cramer@intel.com> Tested-by:
-
Anirudh Venkataramanan authored
ice_reset_subtask needs to handle EMP resets as well, as EMP resets can be triggered by the firmware. This patch adds the logic to do this. Signed-off-by:
Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by:
-
Maor Gottlieb authored
Add new parameter (flow_steering_mode) to control the flow steering mode of the driver. Two modes are supported: 1. DMFS - Device managed flow steering 2. SMFS - Software/Driver managed flow steering. In the DMFS mode, the HW steering entities are created through the FW. In the SMFS mode this entities are created though the driver directly. The driver will use the devlink steering mode only if the steering domain supports it, for now SMFS will manages only the switchdev eswitch steering domain. User command examples: - Set SMFS flow steering mode:: $ devlink dev param set pci/0000:06:00.0 name flow_steering_mode value "smfs" cmode runtime - Read device flow steering mode:: $ devlink dev param show pci/0000:06:00.0 name flow_steering_mode pci/0000:06:00.0: name flow_steering_mode type driver-specific values: cmode runtime value smfs Signed-off-by:Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Maor Gottlieb authored
In case that flow steering mode of the driver is SMFS (Software Managed Flow Steering), then use the DR (SW steering) API to create the steering objects. In addition, add a call to the set peer namespace when switchdev gets devcom pair event. It is required to support VF LAG in SMFS. Signed-off-by:
Mark Bloch <markb@mellanox.com> Signed-off-by:
-
