- 27 Feb, 2012 12 commits
-
-
Sujith Manoharan authored
Change the descriptor length to 24 and explicitly set the control field 23 to zero. Not doing so would result in dropping of frames. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
The LONG_SHIFT_SELECT offset is different for AR9462 from the other chip families. Fix this. Signed-off-by:
-
Sujith Manoharan authored
Using AR_SREV_* macros for setting up the chip-specific NF values will make adding support for new chips hard. Use separate macros for each chip. Currently, AR9462 has the same value for all NF limits. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Validate the phyerr value against the max. size of the statistics array properly. Signed-off-by:
-
Sujith Manoharan authored
Dumping the RSSI information in the middle of error statistics is a bit misleading. Move them to the end. Signed-off-by:
-
Sujith Manoharan authored
Location: <debugfs_path>/ieee80211/phy#/ath9k/reset Signed-off-by:
-
Sujith Manoharan authored
This patch merges the 'wiphy' and 'misc' debugfs files and consolidates the information. Information about the current channel and other HT parameters can be obtained from both mac80211 and iw. Remove such redundant data. The reset statistics have been removed, they will be re-added in a subsequent patch (in a new debugfs file). Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Felix Fietkau authored
Comparing SHA1 checksums of the initval tables has shown that there are many tables that are 100% identical. iniBank{0,1,2,3,7} and iniBB_RfGain are shared by AR5416, AR913x, AR9160 iniBank6 is shared between AR5416 and AR9160 iniBank6TPC is shared between AR913x and AR9160 iniPcieSerdes is the same for all AR9002 based devices The CCK FIR coefficients are shared between AR9271 and AR9287 Getting rid of those duplicates saves about 7.5k uncompressed (on MIPS). For AR9003 and later there are some duplicates as well, but I've decided to leave them in for now, as the initvals for those chips are still actively maintained by QCA. Signed-off-by:Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Gertjan van Wingerde authored
This is an RT3070 based device. Cc: <stable@vger.kernel.org> Reported-by:
Mikhail Kryshen <mikhail@kryshen.net> Signed-off-by:
Gertjan van Wingerde <gwingerde@gmail.com> Acked-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
-
- 22 Feb, 2012 28 commits
-
-
Mohammed Shafi Shajakhan authored
ath_set_channel is called from ath9k_config which already has proper PS wrappers Signed-off-by:
Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
the corresponding code/logic was removed in "ath9k: rework power state handling" Signed-off-by:
-
Jonathan Bither authored
By swithing from our __raw_read and __raw_write functions to ioread32 and iowrite32, benchmarks on my desk with iperf went from 11MBps to 18.1MBps using the AHB bus on an EnGenius ECB3500 running OpenWRT. Signed-off-by:
Jonathan Bither <jonbither@gmail.com> Signed-off-by:
-
Johannes Berg authored
The AP/GO mode API isn't very clearly defined, it has "set beacon" and "new beacon" etc. Modify the API to the following: * start AP -- all settings * change beacon -- new beacon data * stop AP -- stop AP mode operation This also reflects in the nl80211 API, rename the commands there correspondingly (but keep the old names for compatibility.) Overall, this makes it much clearer what's going on in the API. Kalle developed the ath6kl changes, I created the rest of the patch. Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Stanislaw Gruszka authored
Previous name was confusing. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
If rfkill is on il_grab_nic_access() fail and we can not write to the various registers during stop procedure. Write to those registers unconditionally instead. Signed-off-by:
-
Stanislaw Gruszka authored
Using ident is not always good. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
The same data can be gathered using monitor mode. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Remove unneeded structure and cleanup temperature calibration routines a bit. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Handers belongs logically into 4965-mac.c file. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
That change will save us some CPU cycles at run time. Having port-based I/O seems to be not possible for PCIe devices. Signed-off-by:
-
Stanislaw Gruszka authored
wmb(), rmb() are not needed when writel(), readl() are used as accessors for MMIO. We use them indirectly via iowrite32(), ioread32(). What is needed mmiowb(), for synchronizing writes coming from different CPUs on PCIe bridge (see in patch comments). This fortunately is not needed on x86, where mmiowb() is just defined as compiler barrier. As iwlegacy devices are most likely not used on anything other than x86, this is not so important fix. Signed-off-by:
-
Stanislaw Gruszka authored
Before we write to the device register always check if _il_grap_nic_access() was successful. Change type return type _il_grap_nic_access() to bool, and add likely()/unlikely() statements. Signed-off-by:
-
Stanislaw Gruszka authored
Print dump stack when the device is not responding. This should give some more clue about the reason of failure. Also change the message we print, since "MAC in deep sleep" is kinda confusing. On the way add unlikely(), as fail to gain NIC access is hmm ... unlikely. Signed-off-by:
-
