- 22 Jan, 2016 5 commits
-
-
Jonas Jonsson authored
commit f33a7f72 upstream. Some modems, such as the Telit UE910, are using an Infineon Flash Loader utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC Data). The latter can be used as a serial interface to upgrade the firmware of the modem. However, that isn't possible when the cdc-acm driver takes control of the device. The following is an explanation of the behaviour by Daniele Palmas during discussion on linux-usb. "This is what happens when the device is turned on (without modifying the drivers): [155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci [155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11 [155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041 [155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device This is the flashing device that is caught by the cdc-acm driver. Once the ttyACM appears, the application starts sending a magic string (simple write on the file descriptor) to keep the device in flashing mode. If this magic string is not properly received in a certain time interval, the modem goes on in normal operative mode: [155493.748094] usb 1-3: USB disconnect, device number 27 [155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci [155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021 [155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM [155495.059989] usb 1-3: Manufacturer: Telit [155495.059992] usb 1-3: SerialNumber: 359658044004697 [155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device [155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device [155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device [155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device [155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device [155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device [155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14 Using the cdc-acm driver, the string, though being sent in the same way than using the usb-serial-simple driver (I can confirm that the data is passing properly since I used an hw usb sniffer), does not make the device to stay in flashing mode." Signed-off-by:
Jonas Jonsson <jonas@ludd.ltu.se> Tested-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Konstantin Shkolnyy authored
commit 7c90e610 upstream. CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID and completely different from CP210x devices. Signed-off-by:
Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com> Signed-off-by:
-
Dan Carpenter authored
commit 231bfe53 upstream. WARN_ON() only takes a condition argument. I have changed these to WARN() instead. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Felipe Balbi authored
commit 391e6dcb upstream. pxa27x disconnects pullups on suspend but doesn't notify the gadget driver about it, so gadget driver can't disable the endpoints it was using. This causes problems on resume because gadget core will think endpoints are still enabled and just ignore the following usb_ep_enable(). Fix this problem by calling gadget_driver->disconnect(). Tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Felipe Balbi <balbi@ti.com> [ luis: backported to 3.16: - file rename: drivers/usb/gadget/udc/pxa27x_udc.c -> drivers/usb/gadget/pxa27x_udc.c ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
Roman Gushchin authored
commit 3ca8138f upstream. I got a report about unkillable task eating CPU. Further investigation shows, that the problem is in the fuse_fill_write_pages() function. If iov's first segment has zero length, we get an infinite loop, because we never reach iov_iter_advance() call. Fix this by calling iov_iter_advance() before repeating an attempt to copy data from userspace. A similar problem is described in 124d3b70 ("fix writev regression: pan hanging unkillable and un-straceable"). If zero-length segmend is followed by segment with invalid address, iov_iter_fault_in_readable() checks only first segment (zero-length), iov_iter_copy_from_user_atomic() skips it, fails at second and returns zero -> goto again without skipping zero-length segment. Patch calls iov_iter_advance() before goto again: we'll skip zero-length segment at second iteraction and iov_iter_fault_in_readable() will detect invalid address. Special thanks to Konstantin Khlebnikov, who helped a lot with the commit description. Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Maxim Patlasov <mpatlasov@parallels.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
Roman Gushchin <klamm@yandex-team.ru> Signed-off-by:
Miklos Szeredi <miklos@szeredi.hu> Fixes: ea9b9907 ("fuse: implement perform_write") Signed-off-by:
-
- 21 Jan, 2016 1 commit
-
-
Nikolay Aleksandrov authored
commit 0e615e96 upstream. When destroying an mrt table the static mfc entries and the static devices are kept, which leads to devices that can never be destroyed (because of refcnt taken) and leaked memory, for example: unreferenced object 0xffff880034c144c0 (size 192): comm "mfc-broken", pid 4777, jiffies 4320349055 (age 46001.964s) hex dump (first 32 bytes): 98 53 f0 34 00 88 ff ff 98 53 f0 34 00 88 ff ff .S.4.....S.4.... ef 0a 0a 14 01 02 03 04 00 00 00 00 01 00 00 00 ................ backtrace: [<ffffffff815c1b9e>] kmemleak_alloc+0x4e/0xb0 [<ffffffff811ea6e0>] kmem_cache_alloc+0x190/0x300 [<ffffffff815931cb>] ip_mroute_setsockopt+0x5cb/0x910 [<ffffffff8153d575>] do_ip_setsockopt.isra.11+0x105/0xff0 [<ffffffff8153e490>] ip_setsockopt+0x30/0xa0 [<ffffffff81564e13>] raw_setsockopt+0x33/0x90 [<ffffffff814d1e14>] sock_common_setsockopt+0x14/0x20 [<ffffffff814d0b51>] SyS_setsockopt+0x71/0xc0 [<ffffffff815cdbf6>] entry_SYSCALL_64_fastpath+0x16/0x7a [<ffffffffffffffff>] 0xffffffffffffffff Make sure that everything is cleaned on netns destruction. Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by:
Cong Wang <cwang@twopensource.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
- 14 Jan, 2016 1 commit
-
-
Ingo Molnar authored
commit 23a0d4e8 upstream. Tapasweni Pathak reported that we do a kmalloc() in efi_call_phys_prolog() on x86-64 while having interrupts disabled, which is a big no-no, as kmalloc() can sleep. Solve this by removing the irq disabling from the prolog/epilog calls around EFI calls: it's unnecessary, as in this stage we are single threaded in the boot thread, and we don't ever execute this from interrupt contexts. Reported-by:
Tapasweni Pathak <tapaswenipathak@gmail.com> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
Matt Fleming <matt.fleming@intel.com> [ luis: backported to 3.10: adjusted context ] Signed-off-by:
-
- 06 Jan, 2016 1 commit
-
-
Kamal Mostafa authored
commit f6ba98c5 upstream. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Pali Rohar <pali.rohar@gmail.com> Cc: Roberta Dobrescu <roberta.dobrescu@gmail.com> Link: http://lkml.kernel.org/r/1447280736-2161-2-git-send-email-kamal@canonical.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> [ kamal: backport to 3.13-stable: build all tools for this version ] Signed-off-by:
-
- 05 Jan, 2016 14 commits
-
-
Andrew Honig authored
commit 0185604c upstream. Currently if userspace restores the pit counters with a count of 0 on channels 1 or 2 and the guest attempts to read the count on those channels, then KVM will perform a mod of 0 and crash. This will ensure that 0 values are converted to 65536 as per the spec. This is CVE-2015-7513. Signed-off-by:
Andy Honig <ahonig@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Cc: Moritz Muehlenhoff <jmm@inutil.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
David Howells authored
commit b4a1b4f5 upstream. This fixes CVE-2015-7550. There's a race between keyctl_read() and keyctl_revoke(). If the revoke happens between keyctl_read() checking the validity of a key and the key's semaphore being taken, then the key type read method will see a revoked key. This causes a problem for the user-defined key type because it assumes in its read method that there will always be a payload in a non-revoked key and doesn't check for a NULL pointer. Fix this by making keyctl_read() check the validity of a key after taking semaphore instead of before. I think the bug was introduced with the original keyrings code. This was discovered by a multithreaded test program generated by syzkaller (http://github.com/google/syzkaller). Here's a cleaned up version: #include <sys/types.h> #include <keyutils.h> #include <pthread.h> void *thr0(void *arg) { key_serial_t key = (unsigned long)arg; keyctl_revoke(key); return 0; } void *thr1(void *arg) { key_serial_t key = (unsigned long)arg; char buffer[16]; keyctl_read(key, buffer, 16); return 0; } int main() { key_serial_t key = add_key("user", "%", "foo", 3, KEY_SPEC_USER_KEYRING); pthread_t th[5]; pthread_create(&th[0], 0, thr0, (void *)(unsigned long)key); pthread_create(&th[1], 0, thr1, (void *)(unsigned long)key); pthread_create(&th[2], 0, thr0, (void *)(unsigned long)key); pthread_create(&th[3], 0, thr1, (void *)(unsigned long)key); pthread_join(th[0], 0); pthread_join(th[1], 0); pthread_join(th[2], 0); pthread_join(th[3], 0); return 0; } Build as: cc -o keyctl-race keyctl-race.c -lkeyutils -lpthread Run as: while keyctl-race; do :; done as it may need several iterations to crash the kernel. The crash can be summarised as: BUG: unable to handle kernel NULL pointer dereference at 0000000000000010 IP: [<ffffffff81279b08>] user_read+0x56/0xa3 ... Call Trace: [<ffffffff81276aa9>] keyctl_read_key+0xb6/0xd7 [<ffffffff81277815>] SyS_keyctl+0x83/0xe0 [<ffffffff815dbb97>] entry_SYSCALL_64_fastpath+0x12/0x6f Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
David Howells <dhowells@redhat.com> Tested-by:
James Morris <james.l.morris@oracle.com> Signed-off-by:
-
Rainer Weikusat authored
[ Upstream commit 3822b5c2 ] With b3ca9b02, the AF_UNIX SOCK_STREAM receive code was changed from using mutex_lock(&u->readlock) to mutex_lock_interruptible(&u->readlock) to prevent signals from being delayed for an indefinite time if a thread sleeping on the mutex happened to be selected for handling the signal. But this was never a problem with the stream receive code (as opposed to its datagram counterpart) as that never went to sleep waiting for new messages with the mutex held and thus, wouldn't cause secondary readers to block on the mutex waiting for the sleeping primary reader. As the interruptible locking makes the code more complicated in exchange for no benefit, change it back to using mutex_lock. Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 5233252f ] Signed-off-by:
-
WANG Cong authored
[ Upstream commit 09ccfd23 ] Reported-by:
Dmitry Vyukov <dvyukov@gmail.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Sergei Shtylyov authored
[ Upstream commit 248be83d ] In a low memory situation the following kernel oops occurs: Unable to handle kernel NULL pointer dereference at virtual address 00000050 pgd = 8490c000 [00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT ARM Modules linked in: CPU: 0 Not tainted (3.4-at16 #9) PC is at skb_put+0x10/0x98 LR is at sh_eth_poll+0x2c8/0xa10 pc : [<8035f780>] lr : [<8028bf50>] psr: 60000113 sp : 84eb1a90 ip : 84eb1ac8 fp : 84eb1ac4 r10: 0000003f r9 : 000005ea r8 : 00000000 r7 : 00000000 r6 : 940453b0 r5 : 00030000 r4 : 9381b180 r3 : 00000000 r2 : 00000000 r1 : 000005ea r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c53c7d Table: 4248c059 DAC: 00000015 Process klogd (pid: 2046, stack limit = 0x84eb02e8) [...] This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left NULL but sh_eth_rx() later uses it without checking. Add such check... Reported-by:
Yasushi SHOJI <yashi@atmark-techno.com> Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 79462ad0 ] 郭永刚 reported that one could simply crash the kernel as root by using a simple program: int socket_fd; struct sockaddr_in addr; addr.sin_port = 0; addr.sin_addr.s_addr = INADDR_ANY; addr.sin_family = 10; socket_fd = socket(10,3,0x40000000); connect(socket_fd , &addr,16); AF_INET, AF_INET6 sockets actually only support 8-bit protocol identifiers. inet_sock's skc_protocol field thus is sized accordingly, thus larger protocol identifiers simply cut off the higher bits and store a zero in the protocol fields. This could lead to e.g. NULL function pointer because as a result of the cut off inet_num is zero and we call down to inet_autobind, which is NULL for raw sockets. kernel: Call Trace: kernel: [<ffffffff816db90e>] ? inet_autobind+0x2e/0x70 kernel: [<ffffffff816db9a4>] inet_dgram_connect+0x54/0x80 kernel: [<ffffffff81645069>] SYSC_connect+0xd9/0x110 kernel: [<ffffffff810ac51b>] ? ptrace_notify+0x5b/0x80 kernel: [<ffffffff810236d8>] ? syscall_trace_enter_phase2+0x108/0x200 kernel: [<ffffffff81645e0e>] SyS_connect+0xe/0x10 kernel: [<ffffffff81779515>] tracesys_phase2+0x84/0x89 I found no particular commit which introduced this problem. CVE: CVE-2015-8543 Cc: Cong Wang <cwang@twopensource.com> Reported-by:
郭永刚 <guoyonggang@360.cn> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 9470e24f ] SCTP is lacking proper np->opt cloning at accept() time. TCP and DCCP use ipv6_dup_options() helper, do the same in SCTP. We might later factorize this code in a common helper to avoid future mistakes. Reported-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit 01ce63c9 ] Dmitry Vyukov reported that SCTP was triggering a WARN on socket destroy related to disabling sock timestamp. When SCTP accepts an association or peel one off, it copies sock flags but forgot to call net_enable_timestamp() if a packet timestamping flag was copied, leading to extra calls to net_disable_timestamp() whenever such clones were closed. The fix is to call net_enable_timestamp() whenever we copy a sock with that flag on, like tcp does. Reported-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit cb5e173e ] SCTP echoes a cookie o INIT ACK chunks that contains a timestamp, for detecting stale cookies. This cookie is echoed back to the server by the client and then that timestamp is checked. Thing is, if the listening socket is using packet timestamping, the cookie is encoded with ktime_get() value and checked against ktime_get_real(), as done by __net_timestamp(). The fix is to sctp also use ktime_get_real(), so we can compare bananas with bananas later no matter if packet timestamping was enabled or not. Fixes: 52db882f ("net: sctp: migrate cookie life from timeval to ktime") Signed-off-by:
-
Pavel Machek authored
[ Upstream commit f2a3771a ] atl1c driver is doing order-4 allocation with GFP_ATOMIC priority. That often breaks networking after resume. Switch to GFP_KERNEL. Still not ideal, but should be significantly better. atl1c_setup_ring_resources() is called from .open() function, and already uses GFP_KERNEL, so this change is safe. Signed-off-by:
Michal Hocko <mhocko@suse.com> Signed-off-by:
-
Nicolas Dichtel authored
[ Upstream commit 6a61d4db ] Parameters were updated only if the kernel was unable to find the tunnel with the new parameters, ie only if core pamareters were updated (keys, addr, link, type). Now it's possible to update ttl, hoplimit, flowinfo and flags. Fixes: c12b395a ("gre: Support GRE over IPv6") Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
WANG Cong authored
commit 7ba0c47c upstream. We need to wait for the flying timers, since we are going to free the mrtable right after it. Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Vineet Gupta authored
commit 30b9dbee upstream. Signed-off-by:
-
- 21 Dec, 2015 1 commit
-
-
Kamal Mostafa authored
Signed-off-by:
-
- 17 Dec, 2015 9 commits
-
-
Konstantin Khlebnikov authored
commit 6adc5fd6 upstream. Proxy entries could have null pointer to net-device. Signed-off-by:
Konstantin Khlebnikov <koct9i@gmail.com> Fixes: 84920c14 ("net: Allow ipv6 proxies and arp proxies be shown with iproute2") Signed-off-by:
-
Aaro Koskinen authored
commit 3c25a860 upstream. Commit fcb26ec5 ("broadcom: move all PHY_ID's to header") updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0 with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting the original). Fix that. Fixes: fcb26ec5 ("broadcom: move all PHY_ID's to header") Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
-
Rainer Weikusat authored
commit 7d267278 upstream. Rainer Weikusat <rweikusat@mobileactivedefense.com> writes: An AF_UNIX datagram socket being the client in an n:1 association with some server socket is only allowed to send messages to the server if the receive queue of this socket contains at most sk_max_ack_backlog datagrams. This implies that prospective writers might be forced to go to sleep despite none of the message presently enqueued on the server receive queue were sent by them. In order to ensure that these will be woken up once space becomes again available, the present unix_dgram_poll routine does a second sock_poll_wait call with the peer_wait wait queue of the server socket as queue argument (unix_dgram_recvmsg does a wake up on this queue after a datagram was received). This is inherently problematic because the server socket is only guaranteed to remain alive for as long as the client still holds a reference to it. In case the connection is dissolved via connect or by the dead peer detection logic in unix_dgram_sendmsg, the server socket may be freed despite "the polling mechanism" (in particular, epoll) still has a pointer to the corresponding peer_wait queue. There's no way to forcibly deregister a wait queue with epoll. Based on an idea by Jason Baron, the patch below changes the code such that a wait_queue_t belonging to the client socket is enqueued on the peer_wait queue of the server whenever the peer receive queue full condition is detected by either a sendmsg or a poll. A wake up on the peer queue is then relayed to the ordinary wait queue of the client socket via wake function. The connection to the peer wait queue is again dissolved if either a wake up is about to be relayed or the client socket reconnects or a dead peer is detected or the client socket is itself closed. This enables removing the second sock_poll_wait from unix_dgram_poll, thus avoiding the use-after-free, while still ensuring that no blocked writer sleeps forever. Signed-off-by:
Jason Baron <jbaron@akamai.com> Signed-off-by:
-
Nikolay Aleksandrov authored
commit 4c698046 upstream. Similar to ipv4, when destroying an mrt table the static mfc entries and the static devices are kept, which leads to devices that can never be destroyed (because of refcnt taken) and leaked memory. Make sure that everything is cleaned up on netns destruction. Fixes: 8229efda ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code") CC: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by:
-
Noa Osherovich authored
commit d49c2197 upstream. The err variable wasn't set with the correct error value in some cases. Fixes: 47605df9 ('mlx4: Modify proxy/tunnel QP mechanism [..]') Signed-off-by:
Noa Osherovich <noaos@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Daniel Borkmann authored
commit 5cfb4c8d upstream. Since it's introduction in commit 69e3c75f ("net: TX_RING and packet mmap"), TX_RING could be used from SOCK_DGRAM and SOCK_RAW side. When used with SOCK_DGRAM only, the size_max > dev->mtu + reserve check should have reserve as 0, but currently, this is unconditionally set (in it's original form as dev->hard_header_len). I think this is not correct since tpacket_fill_skb() would then take dev->mtu and dev->hard_header_len into account for SOCK_DGRAM, the extra VLAN_HLEN could be possible in both cases. Presumably, the reserve code was copied from packet_snd(), but later on missed the check. Make it similar as we have it in packet_snd(). Fixes: 69e3c75f ("net: TX_RING and packet mmap") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Daniel Borkmann authored
commit 3c70c132 upstream. Packet sockets can be used by various net devices and are not really restricted to ARPHRD_ETHER device types. However, when currently checking for the extra 4 bytes that can be transmitted in VLAN case, our assumption is that we generally probe on ARPHRD_ETHER devices. Therefore, before looking into Ethernet header, check the device type first. This also fixes the issue where non-ARPHRD_ETHER devices could have no dev->hard_header_len in TX_RING SOCK_RAW case, and thus the check would test unfilled linear part of the skb (instead of non-linear). Fixes: 57f89bfa ("network: Allow af_packet to transmit +4 bytes for VLAN packets.") Fixes: 52f1454f ("packet: allow to transmit +4 byte in TX_RING slot for VLAN case") Signed-off-by:
-
Alexander Drozdov authored
commit dbd46ab4 upstream. tpacket_fill_skb() can return a negative value (-errno) which is stored in tp_len variable. In that case the following condition will be (but shouldn't be) true: tp_len > dev->mtu + dev->hard_header_len as dev->mtu and dev->hard_header_len are both unsigned. That may lead to just returning an incorrect EMSGSIZE errno to the user. Fixes: 52f1454f ("packet: allow to transmit +4 byte in TX_RING slot for VLAN case") Signed-off-by:
Alexander Drozdov <al.drozdov@gmail.com> Acked-by:
-
Daniel Borkmann authored
commit 52f1454f upstream. Commit 57f89bfa ("network: Allow af_packet to transmit +4 bytes for VLAN packets.") added the possibility for non-mmaped frames to send extra 4 byte for VLAN header so the MTU increases from 1500 to 1504 byte, for example. Commit cbd89acb ("af_packet: fix for sending VLAN frames via packet_mmap") attempted to fix that for the mmap part but was reverted as it caused regressions while using eth_type_trans() on output path. Lets just act analogous to 57f89bfa and add a similar logic to TX_RING. We presume size_max as overcharged with +4 bytes and later on after skb has been built by tpacket_fill_skb() check for ETH_P_8021Q header on packets larger than normal MTU. Can be easily reproduced with a slightly modified trafgen in mmap(2) mode, test cases: { fill(0xff, 12) const16(0x8100) fill(0xff, <1504|1505>) } { fill(0xff, 12) const16(0x0806) fill(0xff, <1500|1501>) } Note that we need to do the test right after tpacket_fill_skb() as sockets can have PACKET_LOSS set where we would not fail but instead just continue to traverse the ring. Reported-by:
Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Cc: Ben Greear <greearb@candelatech.com> Cc: Phil Sutter <phil@nwl.cc> Tested-by:
-
- 16 Dec, 2015 8 commits
-
-
Sasha Levin authored
commit 119d6f6a upstream. Because wakeups can (fundamentally) be late, a task might not be in the expected state. Therefore testing against a task's state is racy, and can yield false positives. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: oleg@redhat.com Fixes: 9067ac85 ("wake_up_process() should be never used to wakeup a TASK_STOPPED/TRACED task") Link: http://lkml.kernel.org/r/1448933660-23082-1-git-send-email-sasha.levin@oracle.comSigned-off-by:
-
Marcin Wojtas authored
commit dc1aadf6 upstream. A value originally defined in the driver was inappropriate. Even though the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16] are reserved and read-only. This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with the controller's documentation. Signed-off-by:
Marcin Wojtas <mw@semihalf.com> Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by:
-
Marcin Wojtas authored
commit e5bdf689 upstream. MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer allocation was mistakenly set as BIT(1). This commit fixes the assignment. Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by:
-
Marcin Wojtas authored
commit db6ba9a5 upstream. This commit adds missing configuration of MBUS windows access protection in mvneta_conf_mbus_windows function - a dedicated variable for that purpose remained there unused since v3.8 initial mvneta support. Because of that the register contents were inherited from the bootloader. Signed-off-by:
-
Arnd Bergmann authored
commit 92792e48 upstream. Recent gcc versions warn about reading from a negative offset of an on-stack array: drivers/remoteproc/remoteproc_debugfs.c: In function 'rproc_recovery_write': drivers/remoteproc/remoteproc_debugfs.c:167:9: warning: 'buf[4294967295u]' may be used uninitialized in this function [-Wmaybe-uninitialized] I don't see anything in sys_write() that prevents us from being called with a zero 'count' argument, so we should add an extra check in rproc_recovery_write() to prevent the access and avoid the warning. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: 2e37abb8 ("remoteproc: create a 'recovery' debugfs entry") Signed-off-by:
Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by:
-
Christoph Biedl authored
commit 19cebbcb upstream. Commit 35a4a573 ("isdn: clean up debug format string usage") introduced a safeguard to avoid accidential format string interpolation of data when calling debugl1 or HiSax_putstatus. This did however not take into account VHiSax_putstatus (called by HiSax_putstatus) does *not* call vsprintf if the head parameter is NULL - the format string is treated as plain text then instead. As a result, the string "%s" is processed literally, and the actual information is lost. This affects the isdnlog userspace program which stopped logging information since that commit. So revert the HiSax_putstatus invocations to the previous state. Fixes: 35a4a573 ("isdn: clean up debug format string usage") Cc: Kees Cook <keescook@chromium.org> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by:
Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by:
-
Helmut Klein authored
commit 5442f0ea upstream. The "reg" entry in the "poweroff" section of "kirkwood-ts219.dtsi" addressed the wrong uart (0 = console). This patch changes the address to select uart 1, which is the uart connected to the pic microcontroller, which can switch the device off. Signed-off-by:
Helmut Klein <hgkr.klein@gmail.com> Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Fixes: 4350a47b ("ARM: Kirkwood: Make use of the QNAP Power off driver.") Signed-off-by:
-
Eric Dumazet authored
commit 1b8e6a01 upstream. When a passive TCP is created, we eventually call tcp_md5_do_add() with sk pointing to the child. It is not owner by the user yet (we will add this socket into listener accept queue a bit later anyway) But we do own the spinlock, so amend the lockdep annotation to avoid following splat : [ 8451.090932] net/ipv4/tcp_ipv4.c:923 suspicious rcu_dereference_protected() usage! [ 8451.090932] [ 8451.090932] other info that might help us debug this: [ 8451.090932] [ 8451.090934] [ 8451.090934] rcu_scheduler_active = 1, debug_locks = 1 [ 8451.090936] 3 locks held by socket_sockopt_/214795: [ 8451.090936] #0: (rcu_read_lock){.+.+..}, at: [<ffffffff855c6ac1>] __netif_receive_skb_core+0x151/0xe90 [ 8451.090947] #1: (rcu_read_lock){.+.+..}, at: [<ffffffff85618143>] ip_local_deliver_finish+0x43/0x2b0 [ 8451.090952] #2: (slock-AF_INET){+.-...}, at: [<ffffffff855acda5>] sk_clone_lock+0x1c5/0x500 [ 8451.090958] [ 8451.090958] stack backtrace: [ 8451.090960] CPU: 7 PID: 214795 Comm: socket_sockopt_ [ 8451.091215] Call Trace: [ 8451.091216] <IRQ> [<ffffffff856fb29c>] dump_stack+0x55/0x76 [ 8451.091229] [<ffffffff85123b5b>] lockdep_rcu_suspicious+0xeb/0x110 [ 8451.091235] [<ffffffff8564544f>] tcp_md5_do_add+0x1bf/0x1e0 [ 8451.091239] [<ffffffff85645751>] tcp_v4_syn_recv_sock+0x1f1/0x4c0 [ 8451.091242] [<ffffffff85642b27>] ? tcp_v4_md5_hash_skb+0x167/0x190 [ 8451.091246] [<ffffffff85647c78>] tcp_check_req+0x3c8/0x500 [ 8451.091249] [<ffffffff856451ae>] ? tcp_v4_inbound_md5_hash+0x11e/0x190 [ 8451.091253] [<ffffffff85647170>] tcp_v4_rcv+0x3c0/0x9f0 [ 8451.091256] [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0 [ 8451.091260] [<ffffffff856181b6>] ip_local_deliver_finish+0xb6/0x2b0 [ 8451.091263] [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0 [ 8451.091267] [<ffffffff85618d38>] ip_local_deliver+0x48/0x80 [ 8451.091270] [<ffffffff85618510>] ip_rcv_finish+0x160/0x700 [ 8451.091273] [<ffffffff8561900e>] ip_rcv+0x29e/0x3d0 [ 8451.091277] [<ffffffff855c74b7>] __netif_receive_skb_core+0xb47/0xe90 Fixes: a8afca03 ("tcp: md5: protects md5sig_info with RCU") Signed-off-by:
-
