Roman points out that when when we do the low reclaim pass, we scale the
reclaim pressure relative to position between 0 and the maximum
protection threshold.

However, if the maximum protection is based on memory.elow, and
memory.emin is above zero, this means we still may get binary behaviour
on second-pass low reclaim.  This is because we scale starting at 0, not
starting at memory.emin, and since we don't scan at all below emin, we
end up with cliff behaviour.

This should be a fairly uncommon case since usually we don't go into the
second pass, but it makes sense to scale our low reclaim pressure
starting at emin.

You can test this by catting two large sparse files, one in a cgroup
with emin set to some moderate size compared to physical RAM, and
another cgroup without any emin.  In both cgroups, set an elow larger
than 50% of physical RAM.  The one with emin will have less page
scanning, as reclaim pressure is lower.

Rebase on top of and apply the same idea as what was applied to handle
cgroup_memory=disable properly for the original proportional patch
http://lkml.kernel.org/r/20190201045711.GA18302@chrisdown.name ("mm,
memcg: Handle cgroup_disable=memory when getting memcg protection").

Link: http://lkml.kernel.org/r/20190201051810.GA18895@chrisdown.nameSigned-off-by: Chris Down <chris@chrisdown.name>
Suggested-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cgroup v2 introduces two memory protection thresholds: memory.low
(best-effort) and memory.min (hard protection).  While they generally do
what they say on the tin, there is a limitation in their implementation
that makes them difficult to use effectively: that cliff behaviour often
manifests when they become eligible for reclaim.  This patch implements
more intuitive and usable behaviour, where we gradually mount more
reclaim pressure as cgroups further and further exceed their protection
thresholds.

This cliff edge behaviour happens because we only choose whether or not
to reclaim based on whether the memcg is within its protection limits
(see the use of mem_cgroup_protected in shrink_node), but we don't vary
our reclaim behaviour based on this information.  Imagine the following
timeline, with the numbers the lruvec size in this zone:

1. memory.low=1000000, memory.current=999999. 0 pages may be scanned.
2. memory.low=1000000, memory.current=1000000. 0 pages may be scanned.
3. memory.low=1000000, memory.current=1000001. 1000001* pages may be
   scanned. (?!)

* Of course, we won't usually scan all available pages in the zone even
  without this patch because of scan control priority, over-reclaim
  protection, etc.  However, as shown by the tests at the end, these
  techniques don't sufficiently throttle such an extreme change in input,
  so cliff-like behaviour isn't really averted by their existence alone.

Here's an example of how this plays out in practice.  At Facebook, we are
trying to protect various workloads from "system" software, like
configuration management tools, metric collectors, etc (see this[0] case
study).  In order to find a suitable memory.low value, we start by
determining the expected memory range within which the workload will be
comfortable operating.  This isn't an exact science -- memory usage deemed
"comfortable" will vary over time due to user behaviour, differences in
composition of work, etc, etc.  As such we need to ballpark memory.low,
but doing this is currently problematic:

1. If we end up setting it too low for the workload, it won't have
   *any* effect (see discussion above).  The group will receive the full
   weight of reclaim and won't have any priority while competing with the
   less important system software, as if we had no memory.low configured
   at all.

2. Because of this behaviour, we end up erring on the side of setting
   it too high, such that the comfort range is reliably covered.  However,
   protected memory is completely unavailable to the rest of the system,
   so we might cause undue memory and IO pressure there when we *know* we
   have some elasticity in the workload.

3. Even if we get the value totally right, smack in the middle of the
   comfort zone, we get extreme jumps between no pressure and full
   pressure that cause unpredictable pressure spikes in the workload due
   to the current binary reclaim behaviour.

With this patch, we can set it to our ballpark estimation without too much
worry.  Any undesirable behaviour, such as too much or too little reclaim
pressure on the workload or system will be proportional to how far our
estimation is off.  This means we can set memory.low much more
conservatively and thus waste less resources *without* the risk of the
workload falling off a cliff if we overshoot.

As a more abstract technical description, this unintuitive behaviour
results in having to give high-priority workloads a large protection
buffer on top of their expected usage to function reliably, as otherwise
we have abrupt periods of dramatically increased memory pressure which
hamper performance.  Having to set these thresholds so high wastes
resources and generally works against the principle of work conservation.
In addition, having proportional memory reclaim behaviour has other
benefits.  Most notably, before this patch it's basically mandatory to set
memory.low to a higher than desirable value because otherwise as soon as
you exceed memory.low, all protection is lost, and all pages are eligible
to scan again.  By contrast, having a gradual ramp in reclaim pressure
means that you now still get some protection when thresholds are exceeded,
which means that one can now be more comfortable setting memory.low to
lower values without worrying that all protection will be lost.  This is
important because workingset size is really hard to know exactly,
especially with variable workloads, so at least getting *some* protection
if your workingset size grows larger than you expect increases user
confidence in setting memory.low without a huge buffer on top being
needed.

Thanks a lot to Johannes Weiner and Tejun Heo for their advice and
assistance in thinking about how to make this work better.

In testing these changes, I intended to verify that:

1. Changes in page scanning become gradual and proportional instead of
   binary.

   To test this, I experimented stepping further and further down
   memory.low protection on a workload that floats around 19G workingset
   when under memory.low protection, watching page scan rates for the
   workload cgroup:

   +------------+-----------------+--------------------+--------------+
   | memory.low | test (pgscan/s) | control (pgscan/s) | % of control |
   +------------+-----------------+--------------------+--------------+
   |        21G |               0 |                  0 | N/A          |
   |        17G |             867 |               3799 | 23%          |
   |        12G |            1203 |               3543 | 34%          |
   |         8G |            2534 |               3979 | 64%          |
   |         4G |            3980 |               4147 | 96%          |
   |          0 |            3799 |               3980 | 95%          |
   +------------+-----------------+--------------------+--------------+

   As you can see, the test kernel (with a kernel containing this
   patch) ramps up page scanning significantly more gradually than the
   control kernel (without this patch).

2. More gradual ramp up in reclaim aggression doesn't result in
   premature OOMs.

   To test this, I wrote a script that slowly increments the number of
   pages held by stress(1)'s --vm-keep mode until a production system
   entered severe overall memory contention.  This script runs in a highly
   protected slice taking up the majority of available system memory.
   Watching vmstat revealed that page scanning continued essentially
   nominally between test and control, without causing forward reclaim
   progress to become arrested.

[0]: https://facebookmicrosites.github.io/cgroup2/docs/overview.html#case-study-the-fbtax2-project

[akpm@linux-foundation.org: reflow block comments to fit in 80 cols]
[chris@chrisdown.name: handle cgroup_disable=memory when getting memcg protection]
  Link: http://lkml.kernel.org/r/20190201045711.GA18302@chrisdown.name
Link: http://lkml.kernel.org/r/20190124014455.GA6396@chrisdown.nameSigned-off-by: Chris Down <chris@chrisdown.name>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Roman Gushchin <guro@fb.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The "mode" and "level" variables are enums and in this context GCC will
treat them as unsigned ints so the error handling is never triggered.

I also removed the bogus initializer because it isn't required any more
and it's sort of confusing.

[akpm@linux-foundation.org: reduce implicit and explicit typecasting]
[akpm@linux-foundation.org: fix return value, add comment, per Matthew]
Link: http://lkml.kernel.org/r/20190925110449.GO3264@mwanda
Fixes: 3cadfa2b ("mm/vmpressure.c: convert to use match_string() helper")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Enrico Weigelt <info@metux.net>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

On architectures like s390, arch_free_page() could mark the page unused
(set_page_unused()) and any access later would trigger a kernel panic.
Fix it by moving arch_free_page() after all possible accessing calls.

 Hardware name: IBM 2964 N96 400 (z/VM 6.4.0)
 Krnl PSW : 0404e00180000000 0000000026c2b96e (__free_pages_ok+0x34e/0x5d8)
            R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
 Krnl GPRS: 0000000088d43af7 0000000000484000 000000000000007c 000000000000000f
            000003d080012100 000003d080013fc0 0000000000000000 0000000000100000
            00000000275cca48 0000000000000100 0000000000000008 000003d080010000
            00000000000001d0 000003d000000000 0000000026c2b78a 000000002717fdb0
 Krnl Code: 0000000026c2b95c: ec1100b30659 risbgn %r1,%r1,0,179,6
            0000000026c2b962: e32014000036 pfd 2,1024(%r1)
           #0000000026c2b968: d7ff10001000 xc 0(256,%r1),0(%r1)
           >0000000026c2b96e: 41101100  la %r1,256(%r1)
            0000000026c2b972: a737fff8  brctg %r3,26c2b962
            0000000026c2b976: d7ff10001000 xc 0(256,%r1),0(%r1)
            0000000026c2b97c: e31003400004 lg %r1,832
            0000000026c2b982: ebff1430016a asi 5168(%r1),-1
 Call Trace:
 __free_pages_ok+0x16a/0x5d8)
 memblock_free_all+0x206/0x290
 mem_init+0x58/0x120
 start_kernel+0x2b0/0x570
 startup_continue+0x6a/0xc0
 INFO: lockdep is turned off.
 Last Breaking-Event-Address:
 __free_pages_ok+0x372/0x5d8
 Kernel panic - not syncing: Fatal exception: panic_on_oops
 00: HCPGIR450W CP entered; disabled wait PSW 00020001 80000000 00000000 26A2379C

In the past, only kernel_poison_pages() would trigger this but it needs
"page_poison=on" kernel cmdline, and I suspect nobody tested that on
s390.  Recently, kernel_init_free_pages() (commit 6471384a ("mm:
security: introduce init_on_alloc=1 and init_on_free=1 boot options"))
was added and could trigger this as well.

[akpm@linux-foundation.org: add comment]
Link: http://lkml.kernel.org/r/1569613623-16820-1-git-send-email-cai@lca.pw
Fixes: 8823b1db ("mm/page_poison.c: enable PAGE_POISONING as a separate option")
Fixes: 6471384a ("mm: security: introduce init_on_alloc=1 and init_on_free=1 boot options")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Cc: <stable@vger.kernel.org>	[5.3+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There's a really hard to reproduce race in z3fold between z3fold_free()
and z3fold_reclaim_page().  z3fold_reclaim_page() can claim the page
after z3fold_free() has checked if the page was claimed and
z3fold_free() will then schedule this page for compaction which may in
turn lead to random page faults (since that page would have been
reclaimed by then).

Fix that by claiming page in the beginning of z3fold_free() and not
forgetting to clear the claim in the end.

[vitalywool@gmail.com: v2]
  Link: http://lkml.kernel.org/r/20190928113456.152742cf@bigdell
Link: http://lkml.kernel.org/r/20190926104844.4f0c6efa1366b8f5741eaba9@gmail.comSigned-off-by: Vitaly Wool <vitalywool@gmail.com>
Reported-by: Markus Linnala <markus.linnala@gmail.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Henry Burns <henrywolfeburns@gmail.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Markus Linnala <markus.linnala@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Partially revert 16db3d3f ("kernel/sysctl.c: threads-max observe
limits") because the patch is causing a regression to any workload which
needs to override the auto-tuning of the limit provided by kernel.

set_max_threads is implementing a boot time guesstimate to provide a
sensible limit of the concurrently running threads so that runaways will
not deplete all the memory.  This is a good thing in general but there
are workloads which might need to increase this limit for an application
to run (reportedly WebSpher MQ is affected) and that is simply not
possible after the mentioned change.  It is also very dubious to
override an admin decision by an estimation that doesn't have any direct
relation to correctness of the kernel operation.

Fix this by dropping set_max_threads from sysctl_max_threads so any
value is accepted as long as it fits into MAX_THREADS which is important
to check because allowing more threads could break internal robust futex
restriction.  While at it, do not use MIN_THREADS as the lower boundary
because it is also only a heuristic for automatic estimation and admin
might have a good reason to stop new threads to be created even when
below this limit.

This became more severe when we switched x86 from 4k to 8k kernel
stacks.  Starting since 6538b8ea ("x86_64: expand kernel stack to
16K") (3.16) we use THREAD_SIZE_ORDER = 2 and that halved the auto-tuned
value.

In the particular case

  3.12
  kernel.threads-max = 515561

  4.4
  kernel.threads-max = 200000

Neither of the two values is really insane on 32GB machine.

I am not sure we want/need to tune the max_thread value further.  If
anything the tuning should be removed altogether if proven not useful in
general.  But we definitely need a way to override this auto-tuning.

Link: http://lkml.kernel.org/r/20190922065801.GB18814@dhcp22.suse.cz
Fixes: 16db3d3f ("kernel/sysctl.c: threads-max observe limits")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In kdump kernel, memcg usually is disabled with 'cgroup_disable=memory'
for saving memory.  Now kdump kernel will always panic when dump vmcore
to local disk:

  BUG: kernel NULL pointer dereference, address: 0000000000000ab8
  Oops: 0000 [#1] SMP NOPTI
  CPU: 0 PID: 598 Comm: makedumpfile Not tainted 5.3.0+ #26
  Hardware name: HPE ProLiant DL385 Gen10/ProLiant DL385 Gen10, BIOS A40 10/02/2018
  RIP: 0010:mem_cgroup_track_foreign_dirty_slowpath+0x38/0x140
  Call Trace:
   __set_page_dirty+0x52/0xc0
   iomap_set_page_dirty+0x50/0x90
   iomap_write_end+0x6e/0x270
   iomap_write_actor+0xce/0x170
   iomap_apply+0xba/0x11e
   iomap_file_buffered_write+0x62/0x90
   xfs_file_buffered_aio_write+0xca/0x320 [xfs]
   new_sync_write+0x12d/0x1d0
   vfs_write+0xa5/0x1a0
   ksys_write+0x59/0xd0
   do_syscall_64+0x59/0x1e0
   entry_SYSCALL_64_after_hwframe+0x44/0xa9

And this will corrupt the 1st kernel too with 'cgroup_disable=memory'.

Via the trace and with debugging, it is pointing to commit 97b27821
("writeback, memcg: Implement foreign dirty flushing") which introduced
this regression.  Disabling memcg causes the null pointer dereference at
uninitialized data in function mem_cgroup_track_foreign_dirty_slowpath().

Fix it by returning directly if memcg is disabled, but not trying to
record the foreign writebacks with dirty pages.

Link: http://lkml.kernel.org/r/20190924141928.GD31919@MiWiFi-R3L-srv
Fixes: 97b27821 ("writeback, memcg: Implement foreign dirty flushing")
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We get two warnings when build kernel W=1:

  mm/shuffle.c:36:12: warning: no previous prototype for `shuffle_show' [-Wmissing-prototypes]
  mm/sparse.c:220:6: warning: no previous prototype for `subsection_mask_set' [-Wmissing-prototypes]

Make the functions static to fix this.

Link: http://lkml.kernel.org/r/1566978161-7293-1-git-send-email-wang.yi59@zte.com.cnSigned-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

finish_writeback_work() reads @done->waitq after decrementing
@done->cnt.  However, once @done->cnt reaches zero, @done may be freed
(from stack) at any moment and @done->waitq can contain something
unrelated by the time finish_writeback_work() tries to read it.  This
led to the following crash.

  "BUG: kernel NULL pointer dereference, address: 0000000000000002"
  #PF: supervisor write access in kernel mode
  #PF: error_code(0x0002) - not-present page
  PGD 0 P4D 0
  Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
  CPU: 40 PID: 555153 Comm: kworker/u98:50 Kdump: loaded Not tainted
  ...
  Workqueue: writeback wb_workfn (flush-btrfs-1)
  RIP: 0010:_raw_spin_lock_irqsave+0x10/0x30
  Code: 48 89 d8 5b c3 e8 50 db 6b ff eb f4 0f 1f 40 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 53 9c 5b fa 31 c0 ba 01 00 00 00 <f0> 0f b1 17 75 05 48 89 d8 5b c3 89 c6 e8 fe ca 6b ff eb f2 66 90
  RSP: 0018:ffffc90049b27d98 EFLAGS: 00010046
  RAX: 0000000000000000 RBX: 0000000000000246 RCX: 0000000000000000
  RDX: 0000000000000001 RSI: 0000000000000003 RDI: 0000000000000002
  RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000001
  R10: ffff889fff407600 R11: ffff88ba9395d740 R12: 000000000000e300
  R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff88bfdfa00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000002 CR3: 0000000002409005 CR4: 00000000001606e0
  Call Trace:
   __wake_up_common_lock+0x63/0xc0
   wb_workfn+0xd2/0x3e0
   process_one_work+0x1f5/0x3f0
   worker_thread+0x2d/0x3d0
   kthread+0x111/0x130
   ret_from_fork+0x1f/0x30

Fix it by reading and caching @done->waitq before decrementing
@done->cnt.

Link: http://lkml.kernel.org/r/20190924010631.GH2233839@devbig004.ftw2.facebook.com
Fixes: 5b9cce4c ("writeback: Generalize and expose wb_completion")
Signed-off-by: Tejun Heo <tj@kernel.org>
Debugged-by: Chris Mason <clm@fb.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Cc: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>	[5.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

SECTION_SIZE and SECTION_MASK macros are not getting used anymore.  But
they do conflict with existing definitions on arm64 platform causing
following warning during build.  Lets drop these unused macros.

  mm/memremap.c:16: warning: "SECTION_MASK" redefined
   #define SECTION_MASK ~((1UL << PA_SECTION_SHIFT) - 1)
  arch/arm64/include/asm/pgtable-hwdef.h:79: note: this is the location of the previous definition
   #define SECTION_MASK  (~(SECTION_SIZE-1))

  mm/memremap.c:17: warning: "SECTION_SIZE" redefined
   #define SECTION_SIZE (1UL << PA_SECTION_SHIFT)
  arch/arm64/include/asm/pgtable-hwdef.h:78: note: this is the location of the previous definition
   #define SECTION_SIZE  (_AC(1, UL) << SECTION_SHIFT)

Link: http://lkml.kernel.org/r/1569312010-31313-1-git-send-email-anshuman.khandual@arm.comSigned-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Calling 'panic()' on a kernel with CONFIG_PREEMPT=y can leave the
calling CPU in an infinite loop, but with interrupts and preemption
enabled.  From this state, userspace can continue to be scheduled,
despite the system being "dead" as far as the kernel is concerned.

This is easily reproducible on arm64 when booting with "nosmp" on the
command line; a couple of shell scripts print out a periodic "Ping"
message whilst another triggers a crash by writing to
/proc/sysrq-trigger:

  | sysrq: Trigger a crash
  | Kernel panic - not syncing: sysrq triggered crash
  | CPU: 0 PID: 1 Comm: init Not tainted 5.2.15 #1
  | Hardware name: linux,dummy-virt (DT)
  | Call trace:
  |  dump_backtrace+0x0/0x148
  |  show_stack+0x14/0x20
  |  dump_stack+0xa0/0xc4
  |  panic+0x140/0x32c
  |  sysrq_handle_reboot+0x0/0x20
  |  __handle_sysrq+0x124/0x190
  |  write_sysrq_trigger+0x64/0x88
  |  proc_reg_write+0x60/0xa8
  |  __vfs_write+0x18/0x40
  |  vfs_write+0xa4/0x1b8
  |  ksys_write+0x64/0xf0
  |  __arm64_sys_write+0x14/0x20
  |  el0_svc_common.constprop.0+0xb0/0x168
  |  el0_svc_handler+0x28/0x78
  |  el0_svc+0x8/0xc
  | Kernel Offset: disabled
  | CPU features: 0x0002,24002004
  | Memory Limit: none
  | ---[ end Kernel panic - not syncing: sysrq triggered crash ]---
  |  Ping 2!
  |  Ping 1!
  |  Ping 1!
  |  Ping 2!

The issue can also be triggered on x86 kernels if CONFIG_SMP=n,
otherwise local interrupts are disabled in 'smp_send_stop()'.

Disable preemption in 'panic()' before re-enabling interrupts.

Link: http://lkml.kernel.org/r/20191002123538.22609-1-will@kernel.org
Link: https://lore.kernel.org/r/BX1W47JXPMR8.58IYW53H6M5N@dragonstoneSigned-off-by: Will Deacon <will@kernel.org>
Reported-by: Xogium <contact@xogium.me>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In ocfs2_info_scan_inode_alloc(), there is an if statement on line 283
to check whether inode_alloc is NULL:

    if (inode_alloc)

When inode_alloc is NULL, it is used on line 287:

    ocfs2_inode_lock(inode_alloc, &bh, 0);
        ocfs2_inode_lock_full_nested(inode, ...)
            struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);

Thus, a possible null-pointer dereference may occur.

To fix this bug, inode_alloc is checked on line 286.

This bug is found by a static analysis tool STCheck written by us.

Link: http://lkml.kernel.org/r/20190726033717.32359-1-baijiaju1990@gmail.comSigned-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In ocfs2_write_end_nolock(), there are an if statement on lines 1976,
2047 and 2058, to check whether handle is NULL:

    if (handle)

When handle is NULL, it is used on line 2045:

	ocfs2_update_inode_fsync_trans(handle, inode, 1);
        oi->i_sync_tid = handle->h_transaction->t_tid;

Thus, a possible null-pointer dereference may occur.

To fix this bug, handle is checked before calling
ocfs2_update_inode_fsync_trans().

This bug is found by a static analysis tool STCheck written by us.

Link: http://lkml.kernel.org/r/20190726033705.32307-1-baijiaju1990@gmail.comSigned-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In ocfs2_xa_prepare_entry(), there is an if statement on line 2136 to
check whether loc->xl_entry is NULL:

    if (loc->xl_entry)

When loc->xl_entry is NULL, it is used on line 2158:

    ocfs2_xa_add_entry(loc, name_hash);
        loc->xl_entry->xe_name_hash = cpu_to_le32(name_hash);
        loc->xl_entry->xe_name_offset = cpu_to_le16(loc->xl_size);

and line 2164:

    ocfs2_xa_add_namevalue(loc, xi);
        loc->xl_entry->xe_value_size = cpu_to_le64(xi->xi_value_len);
        loc->xl_entry->xe_name_len = xi->xi_name_len;

Thus, possible null-pointer dereferences may occur.

To fix these bugs, if loc-xl_entry is NULL, ocfs2_xa_prepare_entry()
abnormally returns with -EINVAL.

These bugs are found by a static analysis tool STCheck written by us.

[akpm@linux-foundation.org: remove now-unused ocfs2_xa_add_entry()]
Link: http://lkml.kernel.org/r/20190726101447.9153-1-baijiaju1990@gmail.comSigned-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Unused portion of a part-written fs-block-sized block is not set to zero
in unaligned append direct write.This can lead to serious data
inconsistencies.

Ocfs2 manage disk with cluster size(for example, 1M), part-written in
one cluster will change the cluster state from UN-WRITTEN to WRITTEN,
VFS(function dio_zero_block) doesn't do the cleaning because bh's state
is not set to NEW in function ocfs2_dio_wr_get_block when we write a
WRITTEN cluster.  For example, the cluster size is 1M, file size is 8k
and we direct write from 14k to 15k, then 12k~14k and 15k~16k will
contain dirty data.

We have to deal with two cases:
 1.The starting position of direct write is outside the file.
 2.The starting position of direct write is located in the file.

We need set bh's state to NEW in the first case.  In the second case, we
need mapped twice because bh's state of area out file should be set to
NEW while area in file not.

[akpm@linux-foundation.org: coding style fixes]
Link: http://lkml.kernel.org/r/5292e287-8f1a-fd4a-1a14-661e555e0bed@huawei.comSigned-off-by: Jia Guo <guojia12@huawei.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull MIPS fixes from Paul Burton:

 - Build fixes for Cavium Octeon & PMC-Sierra MSP systems, as well as
   all pre-MIPSr6 configurations built with binutils < 2.25.

 - Boot fixes for 64-bit Loongson systems & SGI IP28 systems.

 - Wire up the new clone3 syscall.

 - Clean ups for a few build-time warnings.

* tag 'mips_fixes_5.4_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: fw/arc: Remove unused addr variable
  MIPS: pmcs-msp71xx: Remove unused addr variable
  MIPS: pmcs-msp71xx: Add missing MAX_PROM_MEM definition
  mips: Loongson: Fix the link time qualifier of 'serial_exit()'
  MIPS: init: Prevent adding memory before PHYS_OFFSET
  MIPS: init: Fix reservation of memory between PHYS_OFFSET and mem start
  MIPS: VDSO: Fix build for binutils < 2.25
  MIPS: VDSO: Remove unused gettimeofday.c
  MIPS: Wire up clone3 syscall
  MIPS: octeon: Include required header; fix octeon ethernet build
  MIPS: cpu-bugs64: Mark inline functions as __always_inline
  MIPS: dts: ar9331: fix interrupt-controller size
  MIPS: Loongson64: Fix boot failure after dropping boot_mem_map

Pull RISC-V fixes from Paul Walmsley:

 - Ensure that exclusive-load reservations are terminated after system
   call or exception handling. This primarily affects QEMU, which does
   not expire load reservations.

 - Fix an issue primarily affecting RV32 platforms that can cause the DT
   header to be corrupted, causing boot failures.

* tag 'riscv/for-v5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Fix memblock reservation for device tree blob
  RISC-V: Clear load reservations while restoring hart contexts

Pull DeviceTree fixes from Rob Herring:
 "Fix several 'dt_binding_check' build failures"

* tag 'devicetree-fixes-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: phy: lantiq: Fix Property Name
  dt-bindings: iio: ad7192: Fix DTC warning in the example
  dt-bindings: iio: ad7192: Fix Regulator Properties
  dt-bindings: media: rc: Fix redundant string
  dt-bindings: dsp: Fix fsl,dsp example

The addr variable in prom_free_prom_memory() has been unused since
commit 0df10076 ("MIPS: fw: Record prom memory"), leading to a
compiler warning:

  arch/mips/fw/arc/memory.c:163:16:
    warning: unused variable 'addr' [-Wunused-variable]

Fix this by removing the unused variable.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 0df10076 ("MIPS: fw: Record prom memory")
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-mips@vger.kernel.org

Pull KVM fixes from Paolo Bonzini:
 "ARM and x86 bugfixes of all kinds.

  The most visible one is that migrating a nested hypervisor has always
  been busted on Broadwell and newer processors, and that has finally
  been fixed"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
  KVM: x86: omit "impossible" pmu MSRs from MSR list
  KVM: nVMX: Fix consistency check on injected exception error code
  KVM: x86: omit absent pmu MSRs from MSR list
  selftests: kvm: Fix libkvm build error
  kvm: vmx: Limit guest PMCs to those supported on the host
  kvm: x86, powerpc: do not allow clearing largepages debugfs entry
  KVM: selftests: x86: clarify what is reported on KVM_GET_MSRS failure
  KVM: VMX: Set VMENTER_L1D_FLUSH_NOT_REQUIRED if !X86_BUG_L1TF
  selftests: kvm: add test for dirty logging inside nested guests
  KVM: x86: fix nested guest live migration with PML
  KVM: x86: assign two bits to track SPTE kinds
  KVM: x86: Expose XSAVEERPTR to the guest
  kvm: x86: Enumerate support for CLZERO instruction
  kvm: x86: Use AMD CPUID semantics for AMD vCPUs
  kvm: x86: Improve emulation of CPUID leaves 0BH and 1FH
  KVM: X86: Fix userspace set invalid CR4
  kvm: x86: Fix a spurious -E2BIG in __do_cpuid_func
  KVM: LAPIC: Loosen filter for adaptive tuning of lapic_timer_advance_ns
  KVM: arm/arm64: vgic: Use the appropriate TRACE_INCLUDE_PATH
  arm64: KVM: Kill hyp_alternate_select()
  ...

Pull xen fixes and cleanups from Juergen Gross:

 - a fix in the Xen balloon driver avoiding hitting a BUG_ON() in some
   cases, plus a follow-on cleanup series for that driver

 - a patch for introducing non-blocking EFI callbacks in Xen's EFI
   driver, plu a cleanup patch for Xen EFI handling merging the x86 and
   ARM arch specific initialization into the Xen EFI driver

 - a fix of the Xen xenbus driver avoiding a self-deadlock when cleaning
   up after a user process has died

 - a fix for Xen on ARM after removal of ZONE_DMA

 - a cleanup patch for avoiding build warnings for Xen on ARM

* tag 'for-linus-5.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/xenbus: fix self-deadlock after killing user process
  xen/efi: have a common runtime setup function
  arm: xen: mm: use __GPF_DMA32 for arm64
  xen/balloon: Clear PG_offline in balloon_retrieve()
  xen/balloon: Mark pages PG_offline in balloon_append()
  xen/balloon: Drop __balloon_append()
  xen/balloon: Set pages PageOffline() in balloon_add_region()
  ARM: xen: unexport HYPERVISOR_platform_op function
  xen/efi: Set nonblocking callbacks

Merge tag 'copy-struct-from-user-v5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux

Pull copy_struct_from_user() helper from Christian Brauner:
 "This contains the copy_struct_from_user() helper which got split out
  from the openat2() patchset. It is a generic interface designed to
  copy a struct from userspace.

  The helper will be especially useful for structs versioned by size of
  which we have quite a few. This allows for backwards compatibility,
  i.e. an extended struct can be passed to an older kernel, or a legacy
  struct can be passed to a newer kernel. For the first case (extended
  struct, older kernel) the new fields in an extended struct can be set
  to zero and the struct safely passed to an older kernel.

  The most obvious benefit is that this helper lets us get rid of
  duplicate code present in at least sched_setattr(), perf_event_open(),
  and clone3(). More importantly it will also help to ensure that users
  implementing versioning-by-size end up with the same core semantics.

  This point is especially crucial since we have at least one case where
  versioning-by-size is used but with slighly different semantics:
  sched_setattr(), perf_event_open(), and clone3() all do do similar
  checks to copy_struct_from_user() while rt_sigprocmask(2) always
  rejects differently-sized struct arguments.

  With this pull request we also switch over sched_setattr(),
  perf_event_open(), and clone3() to use the new helper"

* tag 'copy-struct-from-user-v5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  usercopy: Add parentheses around assignment in test_copy_struct_from_user
  perf_event_open: switch to copy_struct_from_user()
  sched_setattr: switch to copy_struct_from_user()
  clone3: switch to copy_struct_from_user()
  lib: introduce copy_struct_from_user() helper

Pull clone3/pidfd fixes from Christian Brauner:
 "This contains a couple of fixes:

   - Fix pidfd selftest compilation (Shuah Kahn)

     Due to a false linking instruction in the Makefile compilation for
     the pidfd selftests would fail on some systems.

   - Fix compilation for glibc on RISC-V systems (Seth Forshee)

     In some scenarios linux/uapi/linux/sched.h is included where
     __ASSEMBLY__ is defined causing a build failure because struct
     clone_args was not guarded by an #ifndef __ASSEMBLY__.

   - Add missing clone3() and struct clone_args kernel-doc (Christian Brauner)

     clone3() and struct clone_args were missing kernel-docs. (The goal
     is to use kernel-doc for any function or type where it's worth it.)
     For struct clone_args this also contains a comment about the fact
     that it's versioned by size"

* tag 'for-linus-20191003' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  sched: add kernel-doc for struct clone_args
  fork: add kernel-doc for clone3
  selftests: pidfd: Fix undefined reference to pthread_create()
  sched: Add __ASSEMBLY__ guards around struct clone_args

Pull drm fixes from Dave Airlie:
 "Been offline for 3 days, got back and had some fixes queued up.

  Nothing too major, the i915 dp-mst fix is important, and amdgpu has a
  bulk move speedup fix and some regressions, but nothing too insane for
  an rc2 pull. The intel fixes are also 2 weeks worth, they missed the
  boat last week.

  core:
   - writeback fixes

  i915:
   - Fix DP-MST crtc_mask
   - Fix dsc dpp calculations
   - Fix g4x sprite scaling stride check with GTT remapping
   - Fix concurrence on cases where requests where getting retired at
     same time as resubmitted to HW
   - Fix gen9 display resolutions by setting the right max plane width
   - Fix GPU hang on preemption
   - Mark contents as dirty on a write fault. This was breaking cursor
     sprite with dumb buffers.

  komeda:
   - memory leak fix

  tilcdc:
   - include fix

  amdgpu:
   - Enable bulk moves
   - Power metrics fixes for Navi
   - Fix S4 regression
   - Add query for tcc disabled mask
   - Fix several leaks in error paths
   - randconfig fixes
   - clang fixes"

* tag 'drm-fixes-2019-10-04' of git://anongit.freedesktop.org/drm/drm: (21 commits)
  Revert "drm/i915: Fix DP-MST crtc_mask"
  drm/omap: fix max fclk divider for omap36xx
  drm/i915: Fix g4x sprite scaling stride check with GTT remapping
  drm/i915/dp: Fix dsc bpp calculations, v5.
  drm/amd/display: fix dcn21 Makefile for clang
  drm/amd/display: hide an unused variable
  drm/amdgpu: display_mode_vba_21: remove uint typedef
  drm/amdgpu: hide another #warning
  drm/amdgpu: make pmu support optional, again
  drm/amd/display: memory leak
  drm/amdgpu: fix multiple memory leaks in acp_hw_init
  drm/amdgpu: return tcc_disabled_mask to userspace
  drm/amdgpu: don't increment vram lost if we are in hibernation
  Revert "drm/amdgpu: disable stutter mode for renoir"
  drm/amd/powerplay: add sensor lock support for smu
  drm/amd/powerplay: change metrics update period from 1ms to 100ms
  drm/amdgpu: revert "disable bulk moves for now"
  drm/tilcdc: include linux/pinctrl/consumer.h again
  drm/komeda: prevent memory leak in komeda_wb_connector_add
  drm: Clear the fence pointer when writeback job signaled
  ...

Pull block fixes from Jens Axboe:

 - Mandate timespec64 for the io_uring timeout ABI (Arnd)

 - Set of NVMe changes via Sagi:
     - controller removal race fix from Balbir
     - quirk additions from Gabriel and Jian-Hong
     - nvme-pci power state save fix from Mario
     - Add 64bit user commands (for 64bit registers) from Marta
     - nvme-rdma/nvme-tcp fixes from Max, Mark and Me
     - Minor cleanups and nits from James, Dan and John

 - Two s390 dasd fixes (Jan, Stefan)

 - Have loop change block size in DIO mode (Martijn)

 - paride pg header ifdef guard (Masahiro)

 - Two blk-mq queue scheduler tweaks, fixing an ordering issue on zoned
   devices and suboptimal performance on others (Ming)

* tag 'for-linus-2019-10-03' of git://git.kernel.dk/linux-block: (22 commits)
  block: sed-opal: fix sparse warning: convert __be64 data
  block: sed-opal: fix sparse warning: obsolete array init.
  block: pg: add header include guard
  Revert "s390/dasd: Add discard support for ESE volumes"
  s390/dasd: Fix error handling during online processing
  io_uring: use __kernel_timespec in timeout ABI
  loop: change queue block size to match when using DIO
  blk-mq: apply normal plugging for HDD
  blk-mq: honor IO scheduler for multiqueue devices
  nvme-rdma: fix possible use-after-free in connect timeout
  nvme: Move ctrl sqsize to generic space
  nvme: Add ctrl attributes for queue_count and sqsize
  nvme: allow 64-bit results in passthru commands
  nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T
  nvmet-tcp: remove superflous check on request sgl
  Added QUIRKs for ADATA XPG SX8200 Pro 512GB
  nvme-rdma: Fix max_hw_sectors calculation
  nvme: fix an error code in nvme_init_subsystem()
  nvme-pci: Save PCI state before putting drive into deepest state
  nvme-tcp: fix wrong stop condition in io_work
  ...

INTEL_PMC_MAX_GENERIC is currently 32, which exceeds the 18
contiguous MSR indices reserved by Intel for event selectors.
Since some machines actually have MSRs past the reserved range,
filtering them against x86_pmu.num_counters_gp may have false
positives.  Cut the list to 18 entries to avoid this.
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Suggested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Jim Mattson <jamttson@google.com>
Fixes: e2ada66e ("kvm: x86: Add Intel PMU MSRs to msrs_to_save[]", 2019-08-21)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Merge tag 'drm-intel-fixes-2019-10-03-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

- Fix DP-MST crtc_mask
- Fix dsc dpp calculations
- Fix g4x sprite scaling stride check with GTT remapping
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003193051.GA26421@intel.com

 - One include fix for tilcdc
 - A clock fix for OMAP
 - A memory leak fix for Komeda
 - Some fixes for resources cleanups with writeback
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003081031.oykms5fg4tijvdri@gilmour

drm-fixes-5.4-2019-10-02:

amdgpu:
- Enable bulk moves
- Power metrics fixes for Navi
- Fix S4 regression
- Add query for tcc disabled mask
- Fix several leaks in error paths
- randconfig fixes
- clang fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002204909.3519-1-alexander.deucher@amd.com

The addr variable in prom_free_prom_memory() has been unused since
commit b3c948e2 ("MIPS: msp: Record prom memory"), causing a warning
& build failure due to -Werror. Remove the unused variable.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b3c948e2 ("MIPS: msp: Record prom memory")
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-mips@vger.kernel.org

Commit b3c948e2 ("MIPS: msp: Record prom memory") introduced use of
a MAX_PROM_MEM value but didn't define it. A bounds check in
prom_meminit() suggests its value was supposed to be 5, so define it as
such & adjust the bounds check to use the macro rather than a magic
number.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b3c948e2 ("MIPS: msp: Record prom memory")
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-mips@vger.kernel.org

Today, put_compat_statfs64() disallows nearly any field value over
2^32 if f_bsize is only 32 bits, but that makes no sense.
compat_statfs64 is there for the explicit purpose of providing 64-bit
fields for f_files, f_ffree, etc.  And f_bsize is always only 32 bits.

As a result, 32-bit userspace gets -EOVERFLOW for i.e.  large file
counts even with -D_FILE_OFFSET_BITS=64 set.

In reality, only f_bsize and f_frsize can legitimately overflow
(fields like f_type and f_namelen should never be large), so test
only those fields.

This bug was discussed at length some time ago, and this is the proposal
Al suggested at https://lkml.org/lkml/2018/8/6/640.  It seemed to get
dropped amid the discussion of other related changes, but this
part seems obviously correct on its own, so I've picked it up and
sent it, for expediency.

Fixes: 64d2ab32 ("vfs: fix put_compat_statfs64() does not handle errors")
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sparse warns about incorrect type when using __be64 data.
It is not being converted to CPU-endian but it should be.

Fixes these sparse warnings:

../block/sed-opal.c:375:20: warning: incorrect type in assignment (different base types)
../block/sed-opal.c:375:20:    expected unsigned long long [usertype] align
../block/sed-opal.c:375:20:    got restricted __be64 const [usertype] alignment_granularity
../block/sed-opal.c:376:25: warning: incorrect type in assignment (different base types)
../block/sed-opal.c:376:25:    expected unsigned long long [usertype] lowest_lba
../block/sed-opal.c:376:25:    got restricted __be64 const [usertype] lowest_aligned_lba

Fixes: 455a7b23 ("block: Add Sed-opal library")
Cc: Scott Bauer <scott.bauer@intel.com>
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Cc: linux-block@vger.kernel.org
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Fix sparse warning: (missing '=')
../block/sed-opal.c:133:17: warning: obsolete array initializer, use C99 syntax

Fixes: ff91064e ("block: sed-opal: check size of shadow mbr")
Cc: linux-block@vger.kernel.org
Cc: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Cc: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

This reverts commit 4eaceea3.

Several userspace clients (modesetting ddx and mutter+wayland at least)
handle encoder.possible_crtcs incorrectly. What they essentially do is
the following:

possible_crtcs = ~0;
for_each_possible_encoder(connector)
	possible_crtcs &= encoder->possible_crtcs;

Ie. they calculate the intersection of the possible_crtcs
for the connector when they really should be calculating the
union instead.

In our case each MST encoder now has just one unique bit set,
and so the intersection is always zero. The end result is that
MST connectors can't be lit up because no crtc can be found to
drive them.

I've submitted a fix for the modesetting ddx [1], and complained
on #wayland about mutter, so hopefully the situation will improve
in the future. In the meantime we have regression, and so must go
back to the old way of misconfiguring possible_crtcs in the kernel.

[1] https://gitlab.freedesktop.org/xorg/xserver/merge_requests/277

Cc: Jonas Ådahl <jadahl@gmail.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111507Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190903154018.26357-1-ville.syrjala@linux.intel.comReviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit e838bfa8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Add kernel-doc for struct clone_args for the clone3() syscall.

Link: https://lore.kernel.org/r/20191001114701.24661-3-christian.brauner@ubuntu.comSigned-off-by: Christian Brauner <christian.brauner@ubuntu.com>

Add kernel-doc for the clone3() syscall.

Link: https://lore.kernel.org/r/20191001114701.24661-2-christian.brauner@ubuntu.comSigned-off-by: Christian Brauner <christian.brauner@ubuntu.com>

Clang warns:

lib/test_user_copy.c:96:10: warning: using the result of an assignment
as a condition without parentheses [-Wparentheses]
        if (ret |= test(umem_src == NULL, "kmalloc failed"))
            ~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
lib/test_user_copy.c:96:10: note: place parentheses around the
assignment to silence this warning
        if (ret |= test(umem_src == NULL, "kmalloc failed"))
                ^
            (                                              )
lib/test_user_copy.c:96:10: note: use '!=' to turn this compound
assignment into an inequality comparison
        if (ret |= test(umem_src == NULL, "kmalloc failed"))
                ^~
                !=

Add the parentheses as it suggests because this is intentional.

Fixes: f5a1a536 ("lib: introduce copy_struct_from_user() helper")
Link: https://github.com/ClangBuiltLinux/linux/issues/731Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Aleksa Sarai <cyphar@cyphar.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191003171121.2723619-1-natechancellor@gmail.comSigned-off-by: Christian Brauner <christian.brauner@ubuntu.com>

Pull kgdb update from Daniel Thompson:
 "This is just a single patch adding a new reviewer for kgdb. New
  reviewers will be a big help so I decided to consider this to be a
  fix!

  I'm looking forward to working more closely with Doug"

* tag 'kgdb-5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
  MAINTAINERS: kgdb: Add myself as a reviewer for kgdb/kdb

I'm interested in kdb / kgdb and have sent various fixes over the
years.  I'd like to get CCed on patches so I can be aware of them and
also help review.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>