- 01 Feb, 2021 30 commits
-
-
Yong Wu authored
Add mt8192 iommu support. Signed-off-by:
Yong Wu <yong.wu@mediatek.com> Reviewed-by:
Tomasz Figa <tfiga@chromium.org> Link: https://lore.kernel.org/r/20210111111914.22211-33-yong.wu@mediatek.comSigned-off-by:
Will Deacon <will@kernel.org>
-
Yong Wu authored
This priv_data is set in the of_xlate. if of_xlate failed, it should not enter attach_device. remove the unnecessary check. Signed-off-by:
-
Yong Wu authored
After extending v7s, our pagetable already support iova reach 16GB(34bit). the master got the iova via dma_alloc_attrs may reach 34bits, but its HW register still is 32bit. then how to set the bit32/bit33 iova? this depend on a SMI larb setting(bank_sel). we separate whole 16GB iova to four banks: bank: 0: 0~4G; 1: 4~8G; 2: 8-12G; 3: 12-16G; The bank number is (iova >> 32). We will preassign which bank the larbs belong to. currently we don't have a interface for master to adjust its bank number. Each a bank is a iova_region which is a independent iommu-domain. the iova range for each iommu-domain can't cross 4G. Signed-off-by:
-
Yong Wu authored
For multiple iommu_domains, we need to reserve some iova regions. Take a example, If the default iova region is 0 ~ 4G, but the 0x4000_0000 ~ 0x43ff_ffff is only for the special CCU0 domain. Thus we should exclude this region for the default iova region. Signed-off-by:
Anan sun <anan.sun@mediatek.com> Signed-off-by:
Chao Hao <chao.hao@mediatek.com> Signed-off-by:
-
Yong Wu authored
Some HW IP(ex: CCU) require the special iova range. That means the iova got from dma_alloc_attrs for that devices must locate in his special range. In this patch, we prepare a iommu group(domain) for each a iova range requirement. Meanwhile we still use one pagetable which support 16GB iova. After this patch, If the iova range of a master is over 4G, the master should: a) Declare its special dma-ranges in its dtsi node. For example, If we preassign the iova 4G-8G for vcodec, then the vcodec dtsi node should add this: /* * iova start at 0x1_0000_0000, pa still start at 0x4000_0000 * size is 0x1_0000_0000. */ dma-ranges = <0x1 0x0 0x0 0x40000000 0x1 0x0>; /* 4G ~ 8G */ Note: we don't have a actual bus concept here. the master doesn't have its special parent node, thus this dma-ranges can only be put in the master's node. b) Update the dma_mask: dma_set_mask_and_coherent(dev, DMA_BIT_MASK(33)); Signed-off-by: -
Yong Wu authored
Add a new interface _get_domain_id from dev->dma_range_map, The iommu consumer device will use dma-ranges in dtsi node to indicate its dma address region requirement. In this iommu driver, we will get the requirement and decide which iova domain it should locate. In the lastest SoC, there will be several iova-regions(domains), we will compare and calculate which domain is right. If the start/end of device requirement equal some region. it is best fit of course. If it is inside some region, it is also ok. the iova requirement of a device should not be inside two or more regions. Signed-off-by:
-
Yong Wu authored
Add a new structure for the iova_region. Each a region will be a independent iommu domain. For the previous SoC, there is single iova region(0~4G). For the SoC that need support multi-domains, there will be several regions. Signed-off-by:
-
Yong Wu authored
Move the domain geometry.aperture updating into domain_finalise. This is a preparing patch for updating the domain region. We know the detailed iova region in the attach_device. Signed-off-by:
-
Yong Wu authored
Currently domain_alloc only has a parameter(type), We have no chance to input some special data. This patch moves the domain_finalise into attach_device which has the device information, then could update the domain's geometry.aperture ranges for each a device. Strictly, I should use the data from mtk_iommu_get_m4u_data as the parameter of mtk_iommu_domain_finalise in this patch. but dom->data only is used in tlb ops in which the data is get from the m4u_list, thus it is ok here. Signed-off-by:
-
Yong Wu authored
Add "struct mtk_iommu_data *" in the "struct mtk_iommu_domain", reduce the call mtk_iommu_get_m4u_data(). No functional change. Signed-off-by:
-
Yong Wu authored
If the iova is over 32bit, the fault status register bit is a little different. Signed-off-by:
-
Yong Wu authored
If the iova is 34bit, the iova[32][33] is the bit0/1 in the tlb flush register. Add a new macro for this. In the macro, since (iova + size - 1) may be end with 0xfff, then the bit0/1 always is 1, thus add a mask. Signed-off-by:
-
Yong Wu authored
In the previous SoC, the M4U HW is in the EMI power domain which is always on. the latest M4U is in the display power domain which may be turned on/off, thus we have to add pm_runtime interface for it. When the engine work, the engine always enable the power and clocks for smi-larb/smi-common, then the M4U's power will always be powered on automatically via the device link with smi-common. Note: we don't enable the M4U power in iommu_map/unmap for tlb flush. If its power already is on, of course it is ok. if the power is off, the main tlb will be reset while M4U power on, thus the tlb flush while m4u power off is unnecessary, just skip it. Therefore, we increase the ref_count for pm when pm status is ACTIVE, otherwise, skip it. Meanwhile, the tlb_flush_range is called so often, thus, update pm ref_count while the SoC has power-domain to avoid touch the dev->power.lock. and the tlb_flush_all only is called when boot, so no need check if the SoC has power-domain to keep code clean. There will be one case that pm runctime status is not expected when tlb flush. After boot, the display may call dma_alloc_attrs before it call pm_runtime_get(disp-dev), then the m4u's pm status is not active inside the dma_alloc_attrs. Since it only happens after boot, the tlb is clean at that time, I also think this is ok. Signed-off-by:
-
Yong Wu authored
In pm runtime case, all the registers backup/restore and bclk are controlled in the pm_runtime callback, Rename the original suspend/resume to the runtime_suspend/resume. Use pm_runtime_force_suspend/resume as the normal suspend/resume. iommu should suspend after iommu consumer devices, thus use _LATE_. Signed-off-by:
-
Yong Wu authored
In the lastest SoC, M4U has its special power domain. thus, If the engine begin to work, it should help enable the power for M4U firstly. Currently if the engine work, it always enable the power/clocks for smi-larbs/smi-common. This patch adds device_link for smi-common and M4U. then, if smi-common power is enabled, the M4U power also is powered on automatically. Normally M4U connect with several smi-larbs and their smi-common always are the same, In this patch it get smi-common dev from the last smi-larb device, then add the device_link. Signed-off-by:
-
Yong Wu authored
In the original code, we lack the error handle. This patch adds them. Signed-off-by:
-
Yong Wu authored
In attach device, it will update the pagetable base address register. Move the hw_init function also here. Then it only need call pm_runtime_get/put one time here if m4u has power domain. Signed-off-by:
-
Yong Wu authored
This patch only updates oas in different SoCs. If the SoC supports 4GB-mode and current dram size is 4GB, the oas is 33. otherwise, it's still 32. In the lastest SoC, the oas is 35bits. Signed-off-by:
-
Yong Wu authored
Add a HW flag for if the HW support 34bit IOVA. the previous SoC still use 32bit. normally the lvl1 pgtable size is 16KB when ias == 32. if ias == 34, lvl1 pgtable size is 16KB * 4. The purpose of this patch is to save 16KB*3 continuous memory for the previous SoC. Signed-off-by:
-
Yong Wu authored
The standard input iova bits is 32. MediaTek quad the lvl1 pagetable (4 * lvl1). No change for lvl2 pagetable. Then the iova bits can reach 34bit. Signed-off-by:
Robin Murphy <robin.murphy@arm.com> Reviewed-by:
-
Yong Wu authored
Add "cfg" as a parameter for some macros. This is a preparing patch for mediatek extend the lvl1 pgtable. No functional change. Signed-off-by:
-
Yong Wu authored
The current _ARM_V7S_LVL_BITS/ARM_V7S_LVL_SHIFT use a formula to calculate the corresponding value for level1 and level2 to pretend the code sane. Actually their level1 and level2 values are different from each other. This patch only clarify the two macro. No functional change. Suggested-by:
-
Yong Wu authored
MediaTek extend the bit5 in lvl1 and lvl2 descriptor as PA34. Signed-off-by:
-
Yong Wu authored
Use the ias for the valid iova checking in arm_v7s_unmap. This is a preparing patch for supporting iova 34bit for MediaTek. Signed-off-by:
-
Yong Wu authored
Use the common memory header(larb-port) in the source code. Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by:
-
Yong Wu authored
This patch adds decriptions for mt8192 IOMMU and SMI. mt8192 also is MTK IOMMU gen2 which uses ARM Short-Descriptor translation table format. The M4U-SMI HW diagram is as below: EMI | M4U | ------------ SMI Common ------------ | +-------+------+------+----------------------+-------+ | | | | ...... | | | | | | | | larb0 larb1 larb2 larb4 ...... larb19 larb20 disp0 disp1 mdp vdec IPE IPE All the connections are HW fixed, SW can NOT adjust it. mt8192 M4U support 0~16GB iova range. we preassign different engines into different iova ranges: domain-id module iova-range larbs 0 disp 0 ~ 4G larb0/1 1 vcodec 4G ~ 8G larb4/5/7 2 cam/mdp 8G ~ 12G larb2/9/11/13/14/16/17/18/19/20 3 CCU0 0x4000_0000 ~ 0x43ff_ffff larb13: port 9/10 4 CCU1 0x4400_0000 ~ 0x47ff_ffff larb14: port 4/5 The iova range for CCU0/1(camera control unit) is HW requirement. Signed-off-by:Rob Herring <robh@kernel.org> Acked-by:
-
Yong Wu authored
Only rename the header guard for all the SoC larb port header file. No funtional change. Suggested-by:
-
Yong Wu authored
Extend the max larb number definition as mt8192 has larb_nr over 16. Signed-off-by:
-
Yong Wu authored
Put all the macros about smi larb/port togethers. Signed-off-by:
-
Yong Wu authored
Convert MediaTek IOMMU to DT schema. Signed-off-by:
-
- 28 Jan, 2021 2 commits
-
-
Robin Murphy authored
IO_PGTABLE_QUIRK_TLBI_ON_MAP is now fully superseded by the core API's iotlb_sync_map callback. Signed-off-by:
-
Robin Murphy authored
The core API can now accommodate invalidate-on-map style behaviour in a single efficient call, so hook that up instead of having io-pgatble do it piecemeal. Signed-off-by:
-
- 27 Jan, 2021 7 commits
-
-
Yong Wu authored
Until now, we have already used the tlb operations from iommu framework, then the tlb operations for v7s can be removed. Correspondingly, Switch the paramenter "cookie" to the internal structure. Signed-off-by:
-
Yong Wu authored
In current iommu_unmap, this code is: iommu_iotlb_gather_init(&iotlb_gather); ret = __iommu_unmap(domain, iova, size, &iotlb_gather); iommu_iotlb_sync(domain, &iotlb_gather); We could gather the whole iova range in __iommu_unmap, and then do tlb synchronization in the iommu_iotlb_sync. This patch implement this, Gather the range in mtk_iommu_unmap. then iommu_iotlb_sync call tlb synchronization for the gathered iova range. we don't call iommu_iotlb_gather_add_page since our tlb synchronization could be regardless of granule size. In this way, gather->start is impossible ULONG_MAX, remove the checking. This patch aims to do tlb synchronization *once* in the iommu_unmap. Signed-off-by:
-
Yong Wu authored
This patch allows io_pgtable_tlb ops could be null since the IOMMU drivers may use the tlb ops from iommu framework. Signed-off-by:
-
Yong Wu authored
Currently gather->end is "unsigned long" which may be overflow in arch32 in the corner case: 0xfff00000 + 0x100000(iova + size). Although it doesn't affect the size(end - start), it affects the checking "gather->end < end" This patch changes this "end" to the real end address (end = start + size - 1). Correspondingly, update the length to "end - start + 1". Fixes: a7d20dc1 ("iommu: Introduce struct iommu_iotlb_gather for batching TLB flushes") Signed-off-by:
-
Yong Wu authored
Remove IO_PGTABLE_QUIRK_TLBI_ON_MAP to avoid tlb sync for each a small chunk memory, Use the new iotlb_sync_map to tlb_sync once for whole the iova range of iommu_map. Signed-off-by:
-
Yong Wu authored
iotlb_sync_map allow IOMMU drivers tlb sync after completing the whole mapping. This patch adds iova and size as the parameters in it. then the IOMMU driver could flush tlb with the whole range once after iova mapping to improve performance. Signed-off-by:
-
Yong Wu authored
In the end of __iommu_map, It alway call iotlb_sync_map. This patch moves iotlb_sync_map out from __iommu_map since it is unnecessary to call this for each sg segment especially iotlb_sync_map is flush tlb all currently. Add a little helper _iommu_map for this. Signed-off-by:
-
- 27 Dec, 2020 1 commit
-
-
Linus Torvalds authored
-
