Merge branch 'for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc

The DL1 PDM interface adds a little gain depending on the output device.
Add a method to retrieve the gain value for machine driver usage.
Signed-off-by: Liam Girdwood <lrg@ti.com>

When multiple headphone or other detectable output pins are present,
the power-map has to be updated after resume appropriately, but the
current driver doesn't check all pins but only the first pin (since
it's enough to check it for the mute-behavior).  This resulted in the
silent output from the secondary outputs after PM resume.

This patch fixes the problem by checking all pins at (re-)init time.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=740347

Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

All Xonar cards support S/PDIF input, but the cards without optical or
coaxial plugs have only undocumented pin connectors.  Support for the
ST/STX was already added in a previous patch; this adds support for the
D1/DX (JP2), DG (J5), DS (J5), and HDAV Slim (J12).

Many thanks to Zoltan Miklos for testing the DS and DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This card shares PCI ids with Chaintec AV710. Therefore, it will not be
detected automatically, it can only be activated by the module parameter
model=sq210a.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When two different cards share the same PCI vendor/subvendor
identification, allow card info based on model only.
Do not require subvendor ID.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add the capture pcm only if there is at least one ADC configured in
the SYSCONF register.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Before, /proc/asound looked like this:

 2 [Default        ]: HDSPM - RME RayDAT_f1cd85
                      RME RayDAT S/N 0xf1cd85 at 0xf7300000, irq 18

In case of a second HDSPM card, its name would be Default_1. This is
cumbersome, because the order of the cards isn't stable across reboots.

To help userspace tools referring to the correct card, this commit
provides a unique id for each card:

 2 [HDSPMxf1cd85   ]: HDSPM - RME RayDAT_f1cd85
                      RME RayDAT S/N 0xf1cd85 at 0xf7300000, irq 18

In this example, userspace (configuration files) would then use
hw:HDSPMxf1cd85 to choose the right card.

The serial is masked to 24bits, so this string is always shorter than
sixteen chars.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The device model needs a release() function so it can free devices when
they become dereferenced.  Do that for rtds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

commit 739be96a "ASoC: Fix build dependency for SND_ATMEL_SOC_SSC"
introduces below build warnings:

drivers/misc/Kconfig:212:error: recursive dependency detected!
drivers/misc/Kconfig:212:       symbol ATMEL_SSC is selected by SND_ATMEL_SOC_SSC
sound/soc/atmel/Kconfig:9:      symbol SND_ATMEL_SOC_SSC is selected by SND_AT91_SOC_SAM9G20_WM8731
sound/soc/atmel/Kconfig:18:     symbol SND_AT91_SOC_SAM9G20_WM8731 depends on ATMEL_SSC

SND_ATMEL_SOC_SSC needs ATMEL_SSC to pass compilation.
This patch remove the "select ATMEL_SSC" from SND_ATMEL_SOC_SSC to avoid above
warnings. And then ensures all the machine drivers that select SND_ATMEL_SOC_SSC
need to depend on ATMEL_SSC.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Currently the driver checks only the out_mix_path[] for the primary
output route for judging whether to create the loopback-mixing control
or not.  But, there are cases where aamix-routing is available only on
headphone or speaker paths but not on the primary output path.  So, the
driver ignores such cases inappropriately.

This patch fixes the check of the loopback-mixing control by testing
all mix-routing paths.

Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When an invalid NID is given, get_wcaps() returns zero as the error,
but get_wcaps_type() takes it as the normal value and returns a bogus
AC_WID_AUD_OUT value.  This confuses the parser.

With this patch, get_wcaps_type() returns -1 when value 0 is given,
i.e. an invalid NID is passed to get_wcaps().

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=740118

Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

These laptops can work well with the auto-parser and their BIOS setups,
and in addition, the auto-parser fixes the problem with S3/S4 where
the unsol event handling is killed after resume due to fallback to the
single-cmd mode.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=740115

Cc: <stable@kernel.org> [v3.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Dan Carpenter reported that setting 0 to uinfo->value.enumerated.items
in snd_asihpi_cmode_info() may lead to Oops.  This function should
return an error immediately in such a case instead.

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Dan Carpenter reported that setting 0 to uinfo->value.enumerated.items
in snd_hdsp_info_pref_sync_ref() may lead to Oops.  This function should
return an error immediately in such a case instead.

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This early 2011 model just need to have headphones on GPI02
instead of GPI01, and use BIOS pincfgs.
It is detected by codec SSID.
The iMac12,1 model is known to work the same way, although maybe
not with the same codec SSID.
Signed-off-by: Jérémy Lal <kapouer@melix.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now that a regulator device for controlling the codec chip reset state
over a platform agnostic regulator API is available on the only board
using this driver so far, extend the driver with a bias control function
which will request virtual power to the codec chip from that virtual
regulator, and will supersede the present implementation existing at the
sound card level.

Thanks to the regulator sharing mechanism, both the old (the sound card)
and the new (the codec) implementations should coexist smoothly until
the sound card file is updated. For this to work as expected, update the
sound card .set_bias_level callback to not touch codec->dapm.bias_level.

While extending the cx20442 structure, drop unused control_type member.

Created against linxu-3.2-rc6, tested on top of patch 1/4 "ARM: OMAP1:
ams-delta: set up a regulator over the modem reset GPIO pin".
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

With some buggy devices, the usb-audio driver may give "frame xxx active"
kernel messages too often.  Better to keep it as debug-only using
snd_printdd(), and also add the rate-limit for avoiding floods.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=738681

Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

They are not needed here.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This is required by the ASoC driver for very low power modes where the
device is fully idle but we want to update controls.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The serial number is used multiple times in hdspm.c. Since it belongs
to the card, let's store it in struct hdspm and refer to it whenever
necessary.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A malicious USB device may feed in carefully crafted min/max/res values,
so that the inner loop in parse_uac2_sample_rate_range() could run for
a long time or even never terminate, e.g., given max = INT_MAX.

Also nr_rates could be a large integer, which causes an integer overflow
in the subsequent call to kmalloc() in parse_audio_format_rates_v2().
Thus, kmalloc() would allocate a smaller buffer than expected, leading
to a memory corruption.

To exploit the two vulnerabilities, an attacker needs physical access
to the machine to plug in a malicious USB device.

This patch makes two changes.

1) The type of "rate" is changed to unsigned int, so that the loop could
   stop once "rate" is larger than INT_MAX.

2) Limit nr_rates to 1024.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fix channels swapping of 4 channels playback by
using vortex_adbdma_stopfifo instead of vortex_adbdma_pausefifo
for SNDRV_PCM_TRIGGER_STOP event
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fix IRQ fifo error when playing stereo by set stereo flag of fifo control.
This also fix the swap of front and rear channels on au8830.
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

- Fix XtalkGainsDefault, XtalkGains1Chn
- Fix XtalkWideCoefsLeftEQ, XtalkWideCoefsRightEQ
- Fix XtlakWideCoefsLeftXT, XtalkWideCoefsRightXT
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Append the external clock item to the clock list only if
the SPDIF_IN capability is defined in the SPDIF register.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Cards with identical PCI ids but no AC97 config in EEPROM do not have
the ac97 field initialized. We must check for this case to avoid kernel oops.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now that we have changed the poulsbo chip to use LPIB position fix,
we can remove the individual machine quirks that do the same thing.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This fixup is not actually used, so in practice this is just a
cosmetic fix.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The CS4213 chip is similar to the CS4210, but it does not have
SPDIF capabilities. Also, it has fewer pins, and the vendor specific
nid is different. With this patch, we have working inputs and outputs
(and automute/autoswitch). However, we don't know anything about
the vendor specific processing coefficients, so we don't read or write
to that node in this patch.

BugLink: https://bugs.launchpad.net/bugs/910792Tested-by: Hsin-Yi Chen <hychen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

There was a bug in the automute logic causing speakers not to
mute when headphones were plugged in.

Cc: stable@kernel.org
Tested-by: Hsin-Yi Chen <hychen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The control name "HP/Speakers" is non-standard, and since there is
only one DAC on this chip there is no need for a virtual master
anyway.

Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

According to the thread on alsa-devel, the LPIB method is to prefer
for Oaktrail controller chip.

Reference: http://mailman.alsa-project.org/pipermail/alsa-devel/2012-January/047800.htmlSigned-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This is a follow up on 53dea36c which fixes the other affected
pcm engines.

Description from 53dea36c:
 Don't rely on the codec's channels_min information to decide wheter or
 not allocate a substream's DMA buffer. Rather check if the substream
 itself was allocated previously.

Without this patch I was seeing null-pointer dereferenc in atmel-pcm.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>