- 23 Sep, 2020 3 commits
-
-
Pierre-Louis Bossart authored
The Master ports can report errors in test data modes, enable the interrupt and just log a message. This capability is useful for Master sink ports only (Master source ports generate data). Signed-off-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by:
Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com> Reviewed-by:
Rander Wang <rander.wang@linux.intel.com> Signed-off-by:
Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20200920193207.31241-4-yung-chuan.liao@linux.intel.comSigned-off-by:
Vinod Koul <vkoul@kernel.org>
-
Pierre-Louis Bossart authored
This patch adds debugfs support to override the Master and Slave data modes. The settings only take effect prior to a new stream being prepared/enabled, or on resume. The test mode can be set to verify data integrity and detect bus clashes, but can only be used to test capture paths. In this case the input generated by a Slave source port is replaced by a fixed or cyclical patterns. Signed-off-by:
-
Pierre-Louis Bossart authored
Test modes are required for all SoundWire IP, and help debug integration issues. In theory each port can be configured with a different mode but to simplify this patch only offers separate configurations for the Master and Slave ports - this covers 99% of the intended cases during platform integration. The test mode value is set via platform-specific ways. Signed-off-by:
-
- 18 Sep, 2020 6 commits
-
-
Vinod Koul authored
FIELD_PREP() does not replace the bits so it is not apt in case where we modify a register. Use u32_replace_bits() or u16_replace_bits() instead. Fixes: 3b4979ca ("soundwire: intel: use FIELD_{GET|PREP}") Tested-by:
-
Vinod Koul authored
FIELD_PREP() does not replace the bits so it is not apt in case where we modify a register. Use u32p_replace_bits() instead. Fixes: 3cf25d63 ("soundwire: cadence: use FIELD_{GET|PREP}") Tested-by:
-
Srinivas Kandagatla authored
currently the max rows and cols values are hardcoded. In reality these values depend on the IP version. So get these based on device tree compatible strings. Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20200917120138.11313-4-srinivas.kandagatla@linaro.orgSigned-off-by:
-
Srinivas Kandagatla authored
This patch adds support to block pack mode, which is required on Qcom soundwire controllers v1.5.x on few ports! Signed-off-by:
-
Srinivas Kandagatla authored
According to usage (bitfields.h) of REG_FIELDS, Modify is: reg &= ~REG_FIELD_C; reg |= FIELD_PREP(REG_FIELD_C, c); Patch ("soundwire: qcom : use FIELD_{GET|PREP}") seems to have accidentally removed clearing bit field while modifying the register. Fix this by using u32p_replace_bits() to clear and set the values. Signed-off-by: -
Bard Liao authored
This algorithm computes bus parameters like clock frequency, frame shape and port transport parameters based on active stream(s) running on the bus. Developers can also implement their own .compute_params() callback for specific resource management algorithm, and set if before calling sdw_add_bus_master() Credits: this patch is based on an earlier internal contribution by Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah. All hard-coded values were removed from the initial contribution to use BIOS information instead. Signed-off-by:
Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20200908131520.5712-1-yung-chuan.liao@linux.intel.comSigned-off-by:
-
- 10 Sep, 2020 7 commits
-
-
Pierre-Louis Bossart authored
The Cadence IP can inject errors, let's make use of this capability to test Slave parity error checks. See e.g. example log where both the master and slave detect the parity error injected on a dummy read command. cd /sys/kernel/debug/soundwire/master-1/intel-sdw/ echo 1 > cdns-parity-error-injection [ 44.756249] intel-master sdw-master-1: Parity error [ 44.756313] intel-master sdw-master-1: Msg NACK received [ 44.756366] intel-master sdw-master-1: Msg NACKed for Slave 15 [ 44.756375] intel-master sdw-master-1: trf on Slave 15 failed:-5 [ 44.756382] intel-master sdw-master-1: parity error injection, read: -5 [ 44.756649] rt1308 sdw:1:25d:1308:0: Parity error detected The code makes sure the Master device is resumed, hence the clock restarted, before sending a parity error. Signed-off-by:
Kai Vehmanen <kai.vehmanen@linux.intel.com> Reviewed-by:
-
Pierre-Louis Bossart authored
Provide prototype and export symbol to enable tests. The bus lock is handled externally to avoid conflicts e.g. between kernel-generated traffic and test traffic. Signed-off-by:
-
Pierre-Louis Bossart authored
The parity calculation is not reset on a Severe Reset, which leads to misleading/harmless errors reported on startup. The addition of a quirk helps filter out such errors while leaving the error checks on in steady-state. Signed-off-by:
Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20200908134521.6781-6-yung-chuan.liao@linux.intel.comSigned-off-by:
-
Pierre-Louis Bossart authored
If a Slave device reports with a quirk that its initial parity check may be incorrect, filter it but keep the parity checks active in steady state. Signed-off-by:
-
Pierre-Louis Bossart authored
Some Slaves report incorrect information in their interrupt status registers after a master/bus reset, track the initial interrupt handling so that quirks can be introduced to filter out incorrect information while keeping interrupts enabled in steady state. Signed-off-by:
-
Pierre-Louis Bossart authored
Unlike the traditional usage, in the SoundWire specification the interrupt masks only gate the propagation of an interrupt condition to the PING frame status. They do not gate the changes of the INT_STAT registers, which will happen regardless of the mask settings. See Figure 116 of the SoundWire 1.2 specification for an in-depth description of the interrupt model. When the bus driver reads the SCP_INT1_STAT register, it will retrieve all the interrupt status, including for the mask fields that were not explicitly set. For example, even if the PARITY mask is not set, the PARITY error status will be reported if an implementation-defined interrupt for jack detection is enabled and occurs. Filtering undesired interrupt reports and handling has to be implemented in software. This patch enables this filtering for the INT1_IMPL_DEF, PARITY and BUS_CLASH interrupt sources. Signed-off-by:
-
Pierre-Louis Bossart authored
Add a slave-level property and program the SCP_INT1_MASK as desired by the codec driver. Since there is no DisCo property this has to be an implementation-specific firmware property or hard-coded in the driver. The only functionality change is that implementation-defined interrupts are no longer set for amplifiers - those interrupts are typically for jack detection or acoustic event detection/hotwording. Signed-off-by:
-
- 09 Sep, 2020 2 commits
-
-
Jonathan Marek authored
Fix slimbus case being broken thanks to a typo. Fixes: 5bd77324 ("soundwire: qcom: avoid dependency on CONFIG_SLIMBUS") Signed-off-by:
Jonathan Marek <jonathan@marek.ca> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20200908140818.28373-1-jonathan@marek.caSigned-off-by:
-
Pierre-Louis Bossart authored
In system suspend stress cases, the SOF CI reports timeouts. The root cause is that an alert is generated while the system suspends. The interrupt handling generates transactions on the bus that will never be handled because the interrupts are disabled in parallel. As a result, the transaction never completes and times out on resume. This error doesn't seem too problematic since it happens in a work queue, and the system recovers without issues. Nevertheless, this race condition should not happen. When doing a system suspend, or when disabling interrupts, we should make sure the current transaction can complete, and prevent new work from being queued. BugLink: https://github.com/thesofproject/linux/issues/2344Signed-off-by:
Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by:
-
- 07 Sep, 2020 4 commits
-
-
Jonathan Marek authored
Add a compatible string for HW version v1.5.1 on sm8250 SoCs. Signed-off-by:
-
Jonathan Marek authored
Adds support for qcom soundwire devices with memory mapped IO registers. Signed-off-by:
-
Jonathan Marek authored
The driver may be used without slimbus, so don't depend on slimbus. Signed-off-by:
-
Jonathan Marek authored
The function name qcom_swrm_abh_reg_read should say ahb, fix that. Signed-off-by:
-
- 04 Sep, 2020 13 commits
-
-
Pierre-Louis Bossart authored
Now that the stream is handled at the dai-link level (in the machine driver), we can remove the stream handling at the dai level. We still need these callbacks to perform dai-level resource handling (i.e. addition/removal of a master). Signed-off-by:
-
Pierre-Louis Bossart authored
Now that the stream trigger is handled at the dai-link level, there is no need for a dai-level trigger any longer. Signed-off-by:
-
Pierre-Louis Bossart authored
snd_soc_dai_get_sdw_stream() can only return the pointer to stream or an ERR_PTR value, NULL is not a possible value. Fixes: 09553140 ('soundwire: intel: implement get_sdw_stream() operations') Reported-by:
-
Pierre-Louis Bossart authored
snd_soc_dai_get_sdw_stream() can only return -ENOTSUPP or the stream, NULL is not a possible value. Fixes: 4550569b ('soundwire: stream: add helper to startup/shutdown streams') Reported-by:
-
Vinod Koul authored
soundwire had defined SDW_REG_SHIFT to calculate shift values for bitmasks, but now that we have better things in bitfield.h, remove this. Signed-off-by:
-
Vinod Koul authored
use FIELD_{GET|PREP} in intel_init driver to get/set field values instead of open coding masks and shift operations. Signed-off-by: -
Vinod Koul authored
use FIELD_{GET|PREP} in intel driver to get/set field values instead of open coding masks and shift operations. Signed-off-by: -
Vinod Koul authored
use FIELD_{GET|PREP} in cadence driver to get/set field values instead of open coding masks and shift operations. Signed-off-by: -
Vinod Koul authored
use FIELD_{GET|PREP} in qcom driver to get/set field values instead of open coding masks and shift operations. Also, remove now unused register shift defines Signed-off-by: -
Vinod Koul authored
use FIELD_{GET|PREP} in stream code to get/set field values instead of open coding masks and shift operations. Signed-off-by: -
Vinod Koul authored
use SDW_DISCO_LINK_ID() in slave code to extract field values instead of open coding masks and shift operations to extract link_id Signed-off-by:
-
Vinod Koul authored
use FIELD_GET() in bus code to extract field values instead of open coding masks and shift operations. Signed-off-by:
-
Vinod Koul authored
Soundwire addr is a 52bit value encoding link, version, unique id, mfg id, part id and class id. Define bit masks for these and use FIELD_GET() to extract these fields. Signed-off-by:
-
- 03 Sep, 2020 5 commits
-
-
Pierre-Louis Bossart authored
Each link has separate power controls, but experimental results show we need to use an all-or-none approach to the link power management. This change has marginal power impacts, the DSP needs to be powered anyways before SoundWire links can be powered, and even when powered a link can be in clock-stopped mode. Signed-off-by:
-
Pierre-Louis Bossart authored
While the hardware exposes independent bits to power-up each master, the recommended sequence is to power all links or none. Idle links can still use the clock stop mode while the master is powered. Signed-off-by:
-
Pierre-Louis Bossart authored
Detect cases where the clock is assumed to be stopped but the IP is not in the relevant state. There is no real way to recover here, but adding an error log can help detect bad programming sequences or race conditions. Signed-off-by:
-
Pierre-Louis Bossart authored
Use platform-specific information to decide when to use hw_sync, not only a number of links > 1. Signed-off-by:
-
Pierre-Louis Bossart authored
set the flags as required by hardware implementation Signed-off-by:
-
