Add USB intialization code to handle the new XLP2XX USB 3.0 block.
This adds xlp/usb-init-xlp2.c to initialize the XLP2XX USB glue-logic
for XHCI and EHCI. Interrupt and IO offset code in xlp-hal/iomap.h
and xlp/nlm_hal.c is also updated for the new USB block.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5744/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

XLP2xx has a new I2C controller which has 4 buses connected to
it. Update the IO offset and IRQ mapping code to reflect this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5707/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

On XLP2xx, wakeup code does not need to enable clock on the core.
Update xlp/wakeup.c to handle this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5703/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add code to calculate the CPU and PIC frequency for XLP2XX SoCs.

Since the PIC frequency on XLP2XX can be configured, add a new macro
pic_timer_freq() to be used in netlogic/common/time.c.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5701/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The config7/config4 register has to be written on all the threads.
This does not cause any problems in XLP, but is needed for XLPII
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5700/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

XLP2XX is first in the series of 28nm XLPII processors.

The changes are to:
* Add processor ID for XLP2XX to asm/cpu.h and kernel/cpu-probe.c.
* Add a cpu_is_xlpii() function to check for XLPII processors.
* Update xlp_mmu_init() to use config4 to enable extended TLB.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5698/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The flash chipselects can span 32MB, fix this in the built-in device
tree.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5704/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Do not pass a memory section in the built-in DTB, and let the
boot code use the values from the DRAM BARs.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5699/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Read the memory from the Bridge DRAM BARs, if it is not passed in
from the device tree. This will allow us to remove memory configuration
from built in device trees.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5743/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The ath79 code uses static clock devices and
provides its own clk_{get,put} implementations.

Change the code to use dynamically allocated
clock devices and register the clocks within
the clkdev framework.

Additionally, remove the local clk_{get,put}
implementation. The clkdev framework has a
common implementation of those.

Also move the call of ath79_clock_init() from
plat_mem_init() to plat_time_init(). Otherwise
it would not be possible to use memory allocation
functions from ath79clock_init() becasuse the
memory subsystem is not yet initialized when
plat_mem_init() runs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5780/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use local variables for ref, cpu, ddr and ahb
rates in SoC specific clock init functions.

The patch has no functional changes, it is
an interim change in preparation of the next
patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5781/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Instead of accessing the rate field of the static
clock devices directly, use the recently introduced
helper function to get the rate of the basic clocks.

The static ath79_{ahb,cpu,ddr,ref}_clk variables
will be removed by a subsequent patch. The actual
change is in preparation of that.

Also move the clock frequency printing code into
the plat_time_init function. We are getting the
cpu clock rate there already so we can save an
extra call of the helper.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5782/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The ath79 platform uses similar code to get the
rate of various clocks during init. Separate the
similar code into a new helper function and use
that to avoid code duplication.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5778/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The reference clock rate is passed in the first
argument of the function. Use that instead of the
rate of the global ath79_ref_clk variable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5779/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The watchdog device on the AR933x is connected to
the AHB clock, however the current code uses the
reference clock. Due to the wrong rate, the watchdog
driver can't calculate correct register values for
a given timeout value and the watchdog unexpectedly
restarts the system.

The code uses the wrong value since the initial
commit 04225e1d
(MIPS: ath79: add AR933X specific clock init)

The patch fixes the code to use the correct clock
rate to avoid the problem.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5777/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The ath79 code supports various SoCs which are using either a 24Kc
or a 74Kc core. The 74Kc core has DSP support, so don't hardwire
the values to zero.

Commit 00dc5ce2 (MIPS: ath79: don't
hardcode the unavailability of the DSP ASE) has fixed this already,
but that change got reverted by 47503256
(MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.)
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5750/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This add a default config for the Lantiq XWAY SoC.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5796/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The clocks of the serial ports were not setup properly.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5659/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add cpu-feature-override.h for the GPON SoC
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5658/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This driver so far only reads the core voltage.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5677/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add a uImage build target for MIPS, which builds uImage.gz (a U-Boot
image of vmlinux.bin.gz), and then symlinks it to uImage. This allows
for the use of other compression algorithms in future, and is how a few
other architectures do it.

It's enabled conditionally on load-y >= 0xffffffff80000000 which
hopefully allows 64bit kernels to also work as long as the load and
entry address can be represented by the 32bit addresses in the U-Boot
image format.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5795/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The vmlinux load address and entry address is calculated in multiple
places:
 - arch/mips/Makefile defines load-y from CONFIG_PHYSICAL_START (or
   defined by the platform) and passes it to
   arch/mips/boot/compressed/Makefile.
 - arch/mips/boot/compressed/Makefile calculates kernel entry using nm.
 - arch/mips/lasat/image/Makefile calculates both load and entry address
   using nm.

Lets combine these in the main Makefile and then pass them as Make
parameters to each of the three boot image Makefiles (in boot/,
boot/compressed, lasat/image/). The boot/ Makefile doesn't currently use
them, but will soon need to for U-Boot image targets.

The existing load-y definition is used in preference to calculating the
load address using nm.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5794/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Split out the arch/mips/boot/ and arch/mips/boot/compressed/ targets
into boot-y and bootz-y variables. This makes it slightly cleaner to add
new targets.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5793/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add symlink to include/dt-bindings from arch/mips/boot/dts/include/ to
match the ones in ARM and Meta architectures so that preprocessed device
tree files can include various useful constant definitions.

See commit c58299aa (kbuild: create an "include chroot" for DT bindings)
merged in v3.10-rc1 for details.

MIPS structures it's dts files a little differently to other
architectures, having a separate dts directory for each SoC/platform,
but most of the definitions in the dt-bindings/ directory are common so
for now lets just have a single "include chroot" for all MIPS platforms.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Steven. J. Hill <steven.hill@imgtec.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kbuild@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Patchwork: http://patchwork.linux-mips.org/patch/5745/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Some toolchains (including Cavium OCTEON SDK) are emitting .eh_frame
sections by default.  Discard them as they are useless in the kernel.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5684/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The SOCs in the OCTEON family have 16 (or in some cases 20) on-chip
GPIO pins, this driver handles them all.  Configuring the pins as
interrupt sources is handled elsewhere (OCTEON's irq handling code).
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5633/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

... and create asm/mach-cavium-octeon/gpio.h so that things continue
to build.

This allows us to use the existing I2C connected GPIO expanders.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5632/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

There were many cases of:

   return something;
   break;

All those break statements are unreachable and thus redundant.
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5727/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Commit 02b849f7 ("MIPS: Get rid of the
use of .macro in C code.") replaced the macro usage but missed
the accessors in bmips.h, causing the following build error:

  CC      arch/mips/kernel/smp-bmips.o
{standard input}: Assembler messages:
{standard input}:951: Error: Unrecognized opcode `_ssnop'
{standard input}:952: Error: Unrecognized opcode `_ssnop'
(...)
make[6]: *** [arch/mips/kernel/smp-bmips.o] Error 1

Fix by rewriting the inline assembler using existing inline functions.
The generated code should stay unchanged.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5644/Reviewed-by: Jonas Gorski <jogo@openwrt.org>

A lot of 64-bit systems supported by Linux/MIPS have boot firmware or
bootloaders that only understand 32-bit ELF files, and as such, the vmlinux.32
target exists to support these systems.  Therefore, it'd be nice if the tar-pkg
target recognised this, and included the right version when packaging up a
binary of the kernel.

This updates buildtar to support MIPS targets.  MIPS may use 'vmlinux'
or 'vmlinux.32' depending on the target system.  This uses 'vmlinux.32'
in preference to 'vmlinux' where present (although I should check which
is newer), including either file as /boot/vmlinux-${version}.

Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1673/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Fix I/O space setup, so that on non-PCI systems using inb()/outb()
won't crash the system. Some drivers may try to probe I/O space and for
that purpose we can just allocate some normal memory initially. Drivers
trying to reserve a region will fail early as we set the size to 0. If
a real I/O space is present, the PCI/PCIe support code will re-adjust
the values accordingly.

Tested with EdgeRouter Lite by enabling CONFIG_SERIO_I8042 that caused
the originally reported crash.
Reported-by: Faidon Liambotis <paravoid@debian.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5626/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Removed parameters checked twice in logical OR operation.
Suggested by coccinelle and manually verified.
Signed-off-by: Alexandru Juncu <alexj@rosedu.org>
Cc: jchandra@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5627/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5638/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

OCTEON2 need the same code.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5637/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5636/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add probing for CNF71XX, CN78XX and CN70XX.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5635/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Needed to support new SOCs.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5634/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use generic-y and remove headers in arch/mips/include/[uapi/]asm/Kbuild
where the header just includes or is identical to the corresponding
<asm-generic/*.h>.

We can't do the same for uapi/asm/kvm_para.h because it's presence is
explicitly checked in include/uapi/linux/Kbuild to decide whether to add
kvm_para.h to header-y.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Dave Jones <davej@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: David Sharp <dhsharp@google.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5581/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

tlbmiss_handler_setup_pgd* are only referenced when
CONFIG_MIPS_PGD_C0_CONTEXT is defined.
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5601/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>