- 13 Mar, 2009 40 commits
-
-
Sascha Hauer authored
This patch adds clkdev support for i.MX31. This is done in a similar way done previously for i.MX27 Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
The UART3 had a copy-paste bug. instead of claiming rxd, txd, rts and cts pins, cts and rts were claimed twice Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
On MX31 we can't do much without mapping the AIPS1/2 register space. Move these mappings from individual boards to plat-mxc/mm.c Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
The i.MX35 basically features the same peripherals as the i.MX31 with some differences: - The i.MX35 has a FEC ethernet controller - The NAND controller base addresses are different - The i.MX35 has only 3 UARTs Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
This patch adds clock support for i.MX35 SoCs. We do not support setting of clock rates yet, but most interesting clock rates should be reported. I couldn't test all clock rates and the datasheet contains some obvious bugs, so expect some bugs in this code. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
We had hardcoded cpu_is_ macros for mxc architectures till now. As we want to run the same kernel on i.MX31 and i.MX35 this patch adds cpu_is_ macros which expand to 0 or 1 if only one architecture is compiled in and only check for the cpu type if more than one architecture is compiled in. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
This patch moves the stuff common to i.MX31 and i.MX35 to mx3x.h and the specifics to mx31.h/mx35.h. We can build a kernel which runs on i.MX31 and i.MX35, so always include mx31.h and mx35.h Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
The var->hsync_len, var->right_margin and var->left_margin fields should contain the real values, not the hardware dependent values. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Valentin Longchamp authored
This adds the dma (ipu_dma) and fb devices for the mx31 for which drivers now are available. v2: merge the ipu and fb device in the same patch as suggested by Sascha Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Valentin Longchamp authored
This enables our mx31moboard to be used on the different baseboards that we are developping according to the application needs. There are not many differences between the boards for now, but when other peripherals are available for mx31 the differences are going to grow. v2: takes Sascha's comments into account Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Valentin Longchamp authored
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Guennadi Liakhovetski authored
Make sure not to create spurious pulses on GPIOs, when configuring them as output: first set required level, then switch direction. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Holger Schurig authored
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
include devices.h from devices.c to avoid inconsistencies and to fix sparse warnings Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
This driver has been tested on MX27/MX31. It should work on MX1/MX1 aswell, but the actual setting of the PWM is missing so far. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
v2: As pointed out by Hans J. Koch we have to claim we can do 24bit to make software like X work. We are lucky on i.MX that 18bit support has the necessary gaps in the fields to do so. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Add framebuffer support for PCM038 Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Sascha Hauer authored
The in kernel FEC driver has recently been ported to a platform driver. Add a platform_device for it and register it for pcm038 and mx27ads. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Mark Brown authored
The i.MX31ADS supports pluggable PMU modules, including the WM835x based Wolfson Microelectronics 1133-EV1. These boards provide power, audio, RTC and watchdiog services to the system. This patch adds initial support for those boards in I2C mode. Currently support is limited by the available support for the features of the i.MX31 in the mainline kernel. Some further work will be needed once other PMU modules are supported and once there is SPI support. Many of the regulator constraints will be sharable with other PMU boards. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Valentin Longchamp authored
This was only compilation tested. Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Valentin Longchamp authored
This was only compilation tested. Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Valentin Longchamp authored
This was only compilation tested. Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Valentin Longchamp authored
This example takes advantage of the possibility to use tables of iomux configs. This is inspired from mx1-mx2 iomux code. It allows a better code readability. Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Valentin Longchamp authored
This new implemenatation avoids that two physical pins are claimed by the same driver (also with the the gpr hardware modes). The gpio kernel lib is also called when a capable gpio pin is assigned its gpio function. The mxc_iomux_mode function is still here for backward compatibility but should not be used anymore. V2: In the precendent revision, the iomux code was claiming a pin when its hardware mode was changed. This was uncorrect: when the hardware mode is changed, the pin must still be claimed through the iomux. In order to have a pin working in mode hw2, we must fist issue the mxc_iomux_set_gpr call and then the corresponding mxc_iomux_mode calls with the FUNC mode (usually done with mxc_iomux_setup_multiple_pins). The reverse calls must be done to fee the pins. Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Uwe Kleine-König authored
... from both mx27ads.c and pcm038.c Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Cc: Holger Schurig <hs4233@mail.mn-solutions.de> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Martin Fuzzey <mfuzzey@gmail.com>
-
Uwe Kleine-König authored
Add a return 0 analogous to uart_mxc_port[0-2]_exit. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Cc: Holger Schurig <hs4233@mail.mn-solutions.de> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Martin Fuzzey <mfuzzey@gmail.com>
-
Mark Brown authored
Keeps sparse happy. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Mark Brown authored
Several of the macros in mx31ads.h depend on mx31.h which is no longer included in quite so many standard headers as it once was. Include it directly so we can build. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Mark Brown authored
The i.MX I2C driver has not yet been merged into mainline but it is near to that and the device defintions don't depend directly on it so we can add the devices now. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-