Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix Makefiles so that Documentation/networking/timestamping/timestamping.c
will build when using the CONFIG_BUILD_DOCSRC kconfig option.
(timestamping.c does not build currently with its simple Makefile.)

Also fix printf format warnings.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The region set by the call to memset is immediately overwritten by the
subsequent call to memcpy.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e1,e2,e3,e4;
@@

- memset(e1,e2,e3);
  memcpy(e1,e4,e3);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace references to the '20' magic number found throughout the Eicon
ISDN driver for the length of the station_id field in the T30_INFO struct
with the T30_MAX_STATION_ID_LENGTH symbolic constant.
Signed-off-by: Ian Munsie <imunsie@au.ibm.com>
Cc: Armin Schindler <mac@melware.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When compiling this driver, the compiler throws the following warnings:

drivers/isdn/hardware/eicon/message.c:8426: warning: array subscript is above array bounds
drivers/isdn/hardware/eicon/message.c:8427: warning: array subscript is above array bounds
drivers/isdn/hardware/eicon/message.c:8434: warning: array subscript is above array bounds
drivers/isdn/hardware/eicon/message.c:8435: warning: array subscript is above array bounds
drivers/isdn/hardware/eicon/message.c:8436: warning: array subscript is above array bounds
drivers/isdn/hardware/eicon/message.c:8447: warning: array subscript is above array bounds

This arises from the particular semantics the driver is using to write to
the nlc array (static byte[256]).  The array has a length in byte 0
followed by a T30_INFO struct starting at byte 1.

The T30_INFO struct has a number of variable length strings after the
station_id entry, which cannot be explicitly defined in the struct and the
driver accesses them with an array index to station_id beyond the length
of station_id.

This patch merely changes the semantics that the driver uses to access the
entries after the station_id entry to use the original 256 byte nlc array
taking the offset and length of the station_id entry to calculate where to
write in the array, thereby silencing the warning.
Signed-off-by: Ian Munsie <imunsie@au.ibm.com>
Cc: Armin Schindler <mac@melware.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The parenthesis was misplaced.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Access to fp->tx_bp_prod is protected by __netif_tx_lock,
smp_mb() is not needed for that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Access to fp->tx_bd_prod is protected by __netif_tx_lock, so we do not
need any barrier for that.

Update of fp->tx_bd_cons in bnx2x_tx_int() is not protected by lock, but
barrier() nor smb_mb() in bnx2x_tx_avail() not guarantee we will see
values that is written on other cpu. Ordering issues between
netif_tx_stop_queue(), netif_tx_queue_stopped(), fp->tx_bd_cons = bd_cons
and bnx2x_tx_avail() are already handled by smp_mb() in bnx2x_tx_int()
and bnx2x_start_xmit().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we want to keep ordering of write to fp->bd_tx_cons and
netif_tx_queue_stopped(txq), what is read of txq->state, we have to use
general memory barrier.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The request to create an mccq was being dispatched without
doing a byte swap of num_pages. This byte swap is necessary
for Big Endian systems like PPC. Not having this fix leads
mccq create to fail on BE ASICs running newer version of
firmware, thereby causing driver initialization failure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Migrate from the legacy PM hooks to use dev_pm_ops structure.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The davinci emac driver uses some ARM specific DMA APIs
for cache coherency which have been removed from kernel
with the 2.6.34 merge.

Modify the driver to use the dma_{map, unmap}_single() APIs
defined in dma-mapping.h

Without this fix, the driver fails to compile on Linus's
tree.

Tested on DM365 and OMAP-L138 EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the PCI pool changes were added to fix resume failures:

commit 98468efd
e100: Use pci pool to work around GFP_ATOMIC order 5 memory allocation failu

and

commit 70abc8cb
e100: Fix broken cbs accounting due to missing memset.

This introduced a problem that can happen if the TX ring size
is increased.  We need to size the PCI pool using cbs->max
instead of the default cbs->count value.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On Wed, 2010-03-10 at 08:41 -0800, David Miller wrote:
> From: Mikael Pettersson <mikpe@it.uu.se>
> Date: Wed, 10 Mar 2010 16:33:28 +0100
> > Booting 2.6.34-rc1 on a machine with a tulip nic I see
> > a number of kernel messages that include "(null)" where
> > previous kernels included the string "tulip0":
> CC:'ing the guilty party :-)  It's one of the following
> commits:

Thanks Mikael.

Anonymity has some good attributes.
Blame avoidance is one of them.

I've broad shoulders.  It's me, then Dwight Howard...

There might be another few of these where ->name or ->dev
was used before struct device or net_device was registered.
I'll go back and check.

tulip_core has:

	if (tp->flags & HAS_MEDIA_TABLE) {
		sprintf(dev->name, DRV_NAME "%d", board_idx);	/* hack */
		tulip_parse_eeprom(dev);
		strcpy(dev->name, "eth%d");			/* un-hack */
	}

So I don't feel _too_ bad.

tulip_parse_eeprom is done before register_netdev so the logging
there can not use netdev_<level> or dev_<level>(&dev->dev
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure we always call rtnl_lock before going down the
error path in sky2_resume, which unlocks the rtnl lock.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we are managing IPv6 addresses using DHCP, it would be nice
for user-space to be notified if an address configured through
DHCP fails DAD.  Otherwise user-space would have to poll to see
whether DAD succeeds.

This patch uses the existing notification mechanism and simply
hooks it into the DAD failure code path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The constant TG3_FLAG_10_100_ONLY should be used with the tg3_flags field,
not the tg3_flags2 field, as done elsewhere in the same file.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some network devices, particularly USB ones, take several seconds to
fully init and appear in the device list.

If the user turned ipconfig on, they are using it for NFS root or some
other early booting purpose.  So it makes no sense to just flat out
fail immediately if the device isn't found.

It also doesn't make sense to just jack up the initial wait to
something crazy like 10 seconds.

Instead, poll immediately, and then periodically once a second,
waiting for a usable device to appear.  Fail after 12 seconds.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Christian Pellegrin <chripell@fsfe.org>

Fix memory leak and use kmalloc() instead of kzalloc() as we are going
to overwrite the allocated buffer.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently hardware with !IEEE80211_HW_PS_NULLFUNC_STACK and
IEEE80211_HW_REPORTS_TX_ACK_STATUS will never enter PSM due to the
conditions in the power save entry functions.

Fix those conditions.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixed below compiler warning:

drivers/net/wireless/ipw2x00/ipw2200.c: In function ‘ipw_load_firmware’:
drivers/net/wireless/ipw2x00/ipw2200.c:3260: warning: the frame size of
1168 bytes is larger than 1024 bytes
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

we read the IQ correction values (i_cal and q_cal) for G mode from a wrong
location (the same shifts as for A mode is applied which is incorrect). use
correct locations, matching the docs and HAL sources.

also we should write IQ correction only when we have that information in the
EEPROM, starting from version 4. also write it in the same way as we do in the
periodic recalibration (enable last), just to be sure.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I/Q calibration was completely broken, resulting in a high number of CRC errors
on received packets. before i could see around 10% to 20% CRC errors, with this
patch they are between 0% and 3%.

1.) the removal of the mask in commit "ath5k: Fix I/Q calibration
(f1cf2dbd)" resulted in no mask beeing used
when writing the I/Q values into the register. additional errors in the
calculation of the values (see 2.) resulted too high numbers, exceeding the
masks, so wrong values like 0xfffffffe were written. to be safe we should
always use the bitmask when writing parts of a register.

2.) using a (s32) cast for q_coff is a wrong conversion to signed, since we
convert to a signed value later by substracting 128. this resulted in too low
numbers for Q many times, which were limited to -16 by the boundary check later
on.

3.) checked everything against the HAL sources and took over comments and minor
optimizations from there.

4.) we can't use ENABLE_BITS when we want to write a number (the number can
contain zeros). also always write the correction values first and set ENABLE
bit last, like the HAL does.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: stable@kernel.org
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

to reset the TSF, AR5K_BEACON_RESET_TSF has to be 1, not 0. also we have a
function for that so use it.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

when using a fixed antenna we should use the antenna number in all tx
descriptors, otherwise the hardware will sometimes send the frame out on the
other antenna. it seems like the hardware does not always respect the default
antenna and diversity settings (esp.  AR5K_STA_ID1_DEFAULT_ANTENNA).

also i would like to note that antenna diversity does not always work correctly
on 5414 (at least) when only one antenna is connected: for example all frames
might be received on antenna A but still the HW tries to send on antenna B some
times, causing packet loss.

this is both verified with the antenna statistics output of the previous patch
and a spectrum analyzer.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ieee->networks consists of 128 struct libipw_network entries. If
we allocate this chunk of memory altogether, it ends up with an
order 4 page allocation. High order page allocation is likely to fail
on system high load. This patch splits the big chunk memory allocation
into small pieces, each is 344 bytes, allocates them with 128 times.

The patch fixed bug http://bugzilla.kernel.org/show_bug.cgi?id=14989Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 34e89507 introduced sta_mtx
locking into sta_info_insert() (now sta_info_insert_rcu), but forgot
to unlock this mutex on one of the error paths. Fix this by adding
the missing mutex_unlock() call for the case where STA insert fails
due to an entry existing already. This may happen at least in AP mode
when a STA roams between two BSSes (vifs).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove the KSEG1ADDR define from rt2x00soc.h as it redefines and covers the
correct one from the arch/mips/include/asm/addrspace.h. Otherwise the driver
oopses on the target platform (Ralink rt3050 board).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some embedded ColdFire based boards use the SMC 91x family of ethernet
devices. (For example the Freescale M5249C3 and MoretonBay NETtel).

Add IO access support to the SMC91x driver, and allow this driver to
be configured for ColdFire platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting new MAC address only worked when device was set to promiscuous mode.
Fix MAC address by writing new address to device using undocumented command
AX_CMD_READ_NODE_ID+1. Patch is tested with AX88772 device.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit a43912ab... ("tunnel: eliminate recursion field") eliminated
use of recursion field from tunnel structures, but its definition
still exists in ip6_tnl{}.

Let's remove that unused field.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 6e17d45a (net: add addr len check to dev_mc_add)
added a bug in dev_mc_add(), since it can now exit with a lock
imbalance.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Annotates neigh_invalidate() with __releases() and __acquires() for
sparse sake.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit d218d111 (tcp: Generalized TTL Security Mechanism) added a bug
for TIMEWAIT sockets. We should not test min_ttl for TW sockets.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 09943a18
	Author: Matt Carlson <mcarlson@broadcom.com>
	Date:   Fri Aug 28 14:01:57 2009 +0000

	tg3: Convert ISR parameter to tnapi

forgot to update tg3_poll_controller(), leading to intermittent crashes with
netpoll.

Fix this.
Signed-off-by: Louis Rilling <louis.rilling@kerlabs.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Deactivate inbound checksumming on HiperSocket is a valid but
dangerous optimization in case the frame is routed from an OSA
network to an HiperSockets network. To go for sure we change the
default to software checksumming.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Depending on their definition in z/VM, virtual devices for z/VM
VSWITCH or GuestLAN must be configured either in layer2 or in
layer3 mode. If qeth detects a layer mismatch, device activation
fails. Trying to recover from this error cannot help; thus
scheduling a recovery should be avoided.
In addition, since recovery is forbidden during online setting of
a qeth device, existence of its network device is guaranteed for all
dev_close() calls in qeth. The corresponding checks can be removed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>