In order to support configuring the device in Double VLAN Mode (DVM),
the DDP and FW have to support DVM. If both support DVM, the PF that
downloads the package needs to update the default recipes, set the
VLAN mode, and update boost TCAM entries.

To support updating the default recipes in DVM, add support for
updating an existing switch recipe's lkup_idx and mask. This is done
by first calling the get recipe AQ (0x0292) with the desired recipe
ID. Then, if that is successful update one of the lookup indices
(lkup_idx) and its associated mask if the mask is valid otherwise
the already existing mask will be used.

The VLAN mode of the device has to be configured while the global
configuration lock is held while downloading the DDP, specifically after
the DDP has been downloaded. If supported, the device will default to
DVM.
Co-developed-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add support for the VF driver to be able to request
VIRTCHNL_VF_OFFLOAD_VLAN_V2, negotiate its VLAN capabilities via
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS, add/delete VLAN filters, and
enable/disable VLAN offloads.

VFs supporting VIRTCHNL_OFFLOAD_VLAN_V2 will be able to use the
following virtchnl opcodes:

VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS
VIRTCHNL_OP_ADD_VLAN_V2
VIRTCHNL_OP_DEL_VLAN_V2
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING_V2
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING_V2
VIRTCHNL_OP_ENABLE_VLAN_INSERTION_V2
VIRTCHNL_OP_DISABLE_VLAN_INSERTION_V2

Legacy VF drivers may expect the initial VLAN stripping settings to be
configured by the PF, so the PF initializes VLAN stripping based on the
VIRTCHNL_OP_GET_VF_RESOURCES opcode. However, with VLAN support via
VIRTCHNL_VF_OFFLOAD_VLAN_V2, this function is only expected to be used
for VFs that only support VIRTCHNL_VF_OFFLOAD_VLAN, which will only
be supported when a port VLAN is configured. Update the function
based on the new expectations. Also, change the message when the PF
can't enable/disable VLAN stripping to a dev_dbg() as this isn't fatal.

When a VF isn't in a port VLAN and it only supports
VIRTCHNL_VF_OFFLOAD_VLAN when Double VLAN Mode (DVM) is enabled, then
the PF needs to reject the VIRTCHNL_VF_OFFLOAD_VLAN capability and
configure the VF in software only VLAN mode. To do this add the new
function ice_vf_vsi_cfg_legacy_vlan_mode(), which updates the VF's
inner and outer ice_vsi_vlan_ops functions and sets up software only
VLAN mode.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently the driver only supports 802.1Q VLAN insertion and stripping.
However, once Double VLAN Mode (DVM) is fully supported, then both 802.1Q
and 802.1ad VLAN insertion and stripping will be supported. Unfortunately
the VSI context parameters only allow for one VLAN ethertype at a time
for VLAN offloads so only one or the other VLAN ethertype offload can be
supported at once.

To support this, multiple changes are needed.

Rx path changes:

[1] In DVM, the Rx queue context l2tagsel field needs to be cleared so
the outermost tag shows up in the l2tag2_2nd field of the Rx flex
descriptor. In Single VLAN Mode (SVM), the l2tagsel field should remain
1 to support SVM configurations.

[2] Modify the ice_test_staterr() function to take a __le16 instead of
the ice_32b_rx_flex_desc union pointer so this function can be used for
both rx_desc->wb.status_error0 and rx_desc->wb.status_error1.

[3] Add the new inline function ice_get_vlan_tag_from_rx_desc() that
checks if there is a VLAN tag in l2tag1 or l2tag2_2nd.

[4] In ice_receive_skb(), add a check to see if NETIF_F_HW_VLAN_STAG_RX
is enabled in netdev->features. If it is, then this is the VLAN
ethertype that needs to be added to the stripping VLAN tag. Since
ice_fix_features() prevents CTAG_RX and STAG_RX from being enabled
simultaneously, the VLAN ethertype will only ever be 802.1Q or 802.1ad.

Tx path changes:

[1] In DVM, the VLAN tag needs to be placed in the l2tag2 field of the Tx
context descriptor. The new define ICE_TX_FLAGS_HW_OUTER_SINGLE_VLAN was
added to the list of tx_flags to handle this case.

[2] When the stack requests the VLAN tag to be offloaded on Tx, the
driver needs to set either ICE_TX_FLAGS_HW_OUTER_SINGLE_VLAN or
ICE_TX_FLAGS_HW_VLAN, so the tag is inserted in l2tag2 or l2tag1
respectively. To determine which location to use, set a bit in the Tx
ring flags field during ring allocation that can be used to determine
which field to use in the Tx descriptor. In DVM, always use l2tag2,
and in SVM, always use l2tag1.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add a new outer_vlan_ops member to the ice_vsi structure as outer VLAN
ops are only available when the device is in Double VLAN Mode (DVM).
Depending on the VSI type, the requirements for what operations to
use/allow differ.

By default all VSI's have unsupported inner and outer VSI VLAN ops. This
implementation was chosen to prevent unexpected crashes due to null
pointer dereferences. Instead, if a VSI calls an unsupported op, it will
just return -EOPNOTSUPP.

Add implementations to support modifying outer VLAN fields for VSI
context. This includes the ability to modify VLAN stripping, insertion,
and the port VLAN based on the outer VLAN handling fields of the VSI
context.

These functions should only ever be used if DVM is enabled because that
means the firmware supports the outer VLAN fields in the VSI context. If
the device is in DVM, then always use the outer_vlan_ops, else use the
vlan_ops since the device is in Single VLAN Mode (SVM).

Also, move adding the untagged VLAN 0 filter from ice_vsi_setup() to
ice_vsi_vlan_setup() as the latter function is specific to the PF and
all other VSI types that need an untagged VLAN 0 filter already do this
in their specific flows. Without this change, Flow Director is failing
to initialize because it does not implement any VSI VLAN ops.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Current operations act on inner VLAN fields. To support double VLAN, outer
VLAN operations and functions will be implemented. Add the "inner" naming
to existing VLAN operations to distinguish them from the upcoming outer
values and functions. Some spacing adjustments are made to align
values.

Note that the inner is not talking about a tunneled VLAN, but the second
VLAN in the packet. For SVM the driver uses inner or single VLAN
filtering and offloads and in Double VLAN Mode the driver uses the
inner filtering and offloads for SR-IOV VFs in port VLANs in order to
support offloading the guest VLAN while a port VLAN is configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently the proto argument is unused. This is because the driver only
supports 802.1Q VLAN filtering. This policy is enforced via netdev
features that the driver sets up when configuring the netdev, so the
proto argument won't ever be anything other than 802.1Q. However, this
will allow for future iterations of the driver to seemlessly support
802.1ad filtering. Begin using the proto argument and extend the related
structures to support its use.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The current vf->port_vlan_info variable is a packed u16 that contains
the port VLAN ID and QoS/prio value. This is fine, but changes are
incoming that allow for an 802.1ad port VLAN. Add flexibility by
changing the vf->port_vlan_info member to be an ice_vlan structure.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add a new struct for VLAN related information. Currently this holds
VLAN ID and priority values, but will be expanded to hold TPID value.
This reduces the changes necessary if any other values are added in
future. Remove the action argument from these calls as it's always
ICE_FWD_VSI.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Incoming changes to support 802.1Q and/or 802.1ad VLAN filtering and
offloads require more flexibility when configuring VLANs. The VSI VLAN
interface will allow flexibility for configuring VLANs for all VSI
types. Add new files to separate the VSI VLAN ops and move functions to
make the code more organized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

There are multiple places where VLAN 0 is being added. Create a function
to be called in order to minimize changes as the implementation is expanded
to support double VLAN and avoid duplicated code.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add functions to configure Tx VLAN antispoof based on iproute
configuration and/or VLAN mode and VF driver support. This is needed
later so the driver can control when it can be configured. Also, add
functions that can be used to enable and disable MAC and VLAN
spoofcheck. Move spoofchk configuration during VSI setup into the
SR-IOV initialization path and into the post VSI rebuild flow for VF
VSIs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Provide generic selftest support. Tested with LAN9500 and LAN9512.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

do_div() does a 64-by-32 division.
When the divisor is u64, do_div() truncates it to 32 bits, this means it
can test non-zero and be truncated to zero for division.

fix do_div.cocci warning:
do_div() does a 64-by-32 division, please consider using div64_u64 instead.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now we can use the enetc_cbd_alloc_data_mem() to replace complicated DMA
data alloc method and CBDR memory basic seting.
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Separate the CBDR data memory alloc standalone. It is convenient for
other part loading, for example the ENETC QOS part.
Reported-and-suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To replace the dma_map_single() stream DMA mapping with DMA coherent
method dma_alloc_coherent() which is more simple.

dma_map_single() found by Tim Gardner not proper. Suggested by Claudiu
Manoil and Jakub Kicinski to use dma_alloc_coherent(). Discussion at:

https://lore.kernel.org/netdev/AM9PR04MB8397F300DECD3C44D2EBD07796BD9@AM9PR04MB8397.eurprd04.prod.outlook.com/t/

Fixes: 888ae5a3 ("net: enetc: add tc flower psfp offload driver")
cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Reported-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciornei says:

====================
dpaa2-eth: add support for software TSO

This series adds support for driver level TSO in the dpaa2-eth driver.

The first 5 patches lay the ground work for the actual feature:
rearrange some variable declaration, cleaning up the interraction with
the S/G Table buffer cache etc.

The 6th patch adds the actual driver level software TSO support by using
the usual tso_build_hdr()/tso_build_data() APIs and creates the S/G FDs.

With this patch set we can see the following improvement in a TCP flow
running on a single A72@2.2GHz of the LX2160A SoC:

before: 6.38Gbit/s
after:  8.48Gbit/s
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Once we added support in the dpaa2-eth for driver level software TSO we
observed the following situation: if the EQCR CI (consumer index) is
read from the cache-enabled area we sometimes end up with a computed
value of available enqueue entries bigger than the size of the ring.

This eventually will lead to the multiple enqueue of the same FD which
will determine the same FD to end up on the Tx confirmation path and the
same skb being freed twice.

Just read the consumer index from the cache inhibited area so that we
avoid this situation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for driver level TSO in the enetc driver using
the TSO API.

There is not much to say about this specific implementation. We are
using the usual tso_build_hdr(), tso_build_data() to create each data
segment, we create an array of S/G FDs where the first S/G entry is
referencing the header data and the remaining ones the data portion.

For the S/G Table buffer we use the same cache of buffers used on the
other non-GSO cases - dpaa2_eth_sgt_get() and dpaa2_eth_sgt_recycle().

We cannot keep a DMA coherent buffer for all the TSO headers because the
DPAA2 architecture does not work in a ring based fashion so we just
allocate a buffer each time.

Even with these limitations we get the following improvement in TCP
termination on the LX2160A SoC, on a single A72 core running at 2.2GHz.

before: 6.38Gbit/s
after:  8.48Gbit/s
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up until now, the __dpaa2_eth_tx function used a single FD on the stack
to construct the structure to be enqueued. Since we are now preparing
the ground work to add support for TSO done in software at the driver
level, the same function needs to work with an array of FDs and enqueue
as many as the build_*_fd functions create.

Make the necessary adjustments in order to do this. These include:
keeping an array of FDs in a percpu structure, cleaning up the necessary
FDs before populating it and then, retrying the enqueue process up till
all the generated FDs were enqueued or until we reach the maximum number
retries.

This patch does not change the fact that only a single FD will result
from a __dpaa2_eth_tx call but rather just creates the necessary changes
for the next patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of allocating memory for an S/G table each time a nonlinear skb
is processed, and then freeing it on the Tx confirmation path, use the
S/G table cache in order to reuse the memory.

For this to work we have to change the size of the cached buffers so
that it can hold the maximum number of scatterlist entries.

Other than that, each allocate/free call is replaced by a call to the
dpaa2_eth_sgt_get/dpaa2_eth_sgt_recycle functions, introduced in the
previous patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dpaa2-eth driver uses in certain circumstances a buffer cache for
the S/G tables needed in case of a S/G FD. At the moment, the
interraction with the cache is open-coded and couldn't be reused easily.

Add two new functions - dpaa2_eth_sgt_get and dpaa2_eth_sgt_recycle -
which help with code reusability.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of allocating memory and then manually aligning it to the
desired value use napi_alloc_frag_align() directly to streamline the
process.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the next patches we'll be moving things arroung in the mentioned
function and also add some new variable declarations. Before all this,
cleanup the variable declaration order.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Kelam says:

====================
Priority flow control support for RVU netdev

In network congestion, instead of pausing all traffic on link
PFC allows user to selectively pause traffic according to its
class. This series of patches add support of PFC for RVU netdev
drivers.

Patch1 adds support to disable pause frames by default as
with PFC user can enable either PFC or 802.3 pause frames.
Patch2&3 adds resource management support for flow control
and configures necessary registers for PFC.
Patch4 adds dcb ops registration for netdev drivers.

V2 changes:
Fix compilation error by exporting required symbols 'otx2_config_pause_frm'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Data centric bridging designed to eliminate packet loss due to
queue overflow by adding enhancements to ethernet network such as
proprity flow control etc. This patch adds support for management
of Priority flow control(PFC) on Octeontx2 and CN10K interfaces.

To enable PFC for all priorities
	dcb pfc set dev eth0 prio-pfc all:on/off

To enable PFC on selected priorites
	dcb pfc set dev eth0 prio-pfc 0:on/off 1:on/off ..7:on/off

With the ntuple commands user can map Priority to receive queues.
On queue overflow NIX will assert backpressure such that PFC pause frames
are genarated with mapped priority.

To map priority 7 to Queue 1
ethtool -U eth0 flow-type ether dst xx:xx:xx:xx:xx:xx vlan 0xe00a
m 0x1fff  queue 1
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CN10K MAC block (RPM) and Octeontx2 MAC block (CGX) both supports
PFC flow control and 802.3X flow control pause frames.

Each MAC block supports max 4 LMACS and AF driver assigns same
(MAC,LMAC) to PF and its VFs. As PF and its share same (MAC,LMAC)
pair we need resource management to address below scenarios

1. Maintain PFC and 8023X pause frames mutually exclusive.
2. Reject disable flow control request if other PF or Vfs
   enabled it.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prirority based flow control (802.1Qbb)  mechanism is similar to
ethernet pause frames (802.3x) instead pausing all traffic on a link,
PFC allows user to selectively pause traffic according to its class.

Oceteontx2 MAC block (CGX) and CN10K Mac block (RPM) both supports
PFC. As upper layer mbox handler is same for both the MACs, this
patch configures PFC by calling apporopritate callbacks.
Signed-off-by: Sunil Kumar Kori <skori@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current implementation is such that 802.3x pause frames are
enabled by default.  As CGX and RPM blocks support PFC
(priority flow control) also, instead of driver enabling one
between them enable them upon request from PF or its VFs.
Also add support to disable pause frames in driver unbind.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeremy Kerr says:

====================
MCTP tag control interface

This series implements a small interface for userspace-controlled
message tag allocation for the MCTP protocol. Rather than leaving the
kernel to allocate per-message tag values, userspace can explicitly
allocate (and release) message tags through two new ioctls:
SIOCMCTPALLOCTAG and SIOCMCTPDROPTAG.

In order to do this, we first introduce some minor changes to the tag
handling, including a couple of new tests for the route input paths.

As always, any comments/queries/etc are most welcome.

v2:
 - make mctp_lookup_prealloc_tag static
 - minor checkpatch formatting fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This change adds a couple of new ioctls for mctp sockets:
SIOCMCTPALLOCTAG and SIOCMCTPDROPTAG.  These ioctls provide facilities
for explicit allocation / release of tags, overriding the automatic
allocate-on-send/release-on-reply and timeout behaviours. This allows
userspace more control over messages that may not fit a simple
request/response model.

In order to indicate a pre-allocated tag to the sendmsg() syscall, we
introduce a new flag to the struct sockaddr_mctp.smctp_tag value:
MCTP_TAG_PREALLOC.

Additional changes from Jeremy Kerr <jk@codeconstruct.com.au>.

Contains a fix that was:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, we require an exact match on an incoming packet's dest
address, and the key's local_addr field.

In a future change, we may want to set up a key before packets are
routed, meaning we have no local address to match on.

This change allows key lookups to match on local_addr = MCTP_ADDR_ANY.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, we have a couple of paths that check that an EID matches, or
the match value is MCTP_ADDR_ANY.

Rather than open coding this, add a little helper.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change adds a few more tests to check the key/tag lookups on route
input. We add a specific entry to the keys lists, route a packet with
specific header values, and check for key match/mismatch.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a definition for the tag-owner flag, which has TO as a standard
abbreviation. We'll want to add a helper for the actual tag value in a
future change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

-queue

Tony Nguyen says:

====================
40GbE Intel Wired LAN Driver Updates 2022-02-08

Joe Damato says:

This patch set makes several updates to the i40e driver stats collection
and reporting code to help users of i40e get a better sense of how the
driver is performing and interacting with the rest of the kernel.

These patches include some new stats (like waived and busy) which were
inspired by other drivers that track stats using the same nomenclature.

The new stats and an existing stat, rx_reuse, are now accessible with
ethtool to make harvesting this data more convenient for users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to test that skb has a dst attached to it.

general protection fault, probably for non-canonical address 0xdffffc0000000011: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000088-0x000000000000008f]
CPU: 0 PID: 32650 Comm: syz-executor.4 Not tainted 5.17.0-rc2-next-20220204-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:ip6_tnl_xmit+0x2140/0x35f0 net/ipv6/ip6_tunnel.c:1127
Code: 4d 85 f6 0f 85 c5 04 00 00 e8 9c b0 66 f9 48 83 e3 fe 48 b8 00 00 00 00 00 fc ff df 48 8d bb 88 00 00 00 48 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 07 7f 05 e8 11 25 b2 f9 44 0f b6 b3 88 00 00
RSP: 0018:ffffc900141b7310 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffc9000c77a000
RDX: 0000000000000011 RSI: ffffffff8811f854 RDI: 0000000000000088
RBP: ffffc900141b7480 R08: 0000000000000000 R09: 0000000000000008
R10: ffffffff8811f846 R11: 0000000000000008 R12: ffffc900141b7548
R13: ffff8880297c6000 R14: 0000000000000000 R15: ffff8880351c8dc0
FS:  00007f9827ba2700(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b31322000 CR3: 0000000033a70000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 ipxip6_tnl_xmit net/ipv6/ip6_tunnel.c:1386 [inline]
 ip6_tnl_start_xmit+0x71e/0x1830 net/ipv6/ip6_tunnel.c:1435
 __netdev_start_xmit include/linux/netdevice.h:4683 [inline]
 netdev_start_xmit include/linux/netdevice.h:4697 [inline]
 xmit_one net/core/dev.c:3473 [inline]
 dev_hard_start_xmit+0x1eb/0x920 net/core/dev.c:3489
 __dev_queue_xmit+0x2a24/0x3760 net/core/dev.c:4116
 packet_snd net/packet/af_packet.c:3057 [inline]
 packet_sendmsg+0x2265/0x5460 net/packet/af_packet.c:3084
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:725
 sock_write_iter+0x289/0x3c0 net/socket.c:1061
 call_write_iter include/linux/fs.h:2075 [inline]
 do_iter_readv_writev+0x47a/0x750 fs/read_write.c:726
 do_iter_write+0x188/0x710 fs/read_write.c:852
 vfs_writev+0x1aa/0x630 fs/read_write.c:925
 do_writev+0x27f/0x300 fs/read_write.c:968
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f9828c2d059

Fixes: c1f55c5e ("ip6_tunnel: allow routing IPv4 traffic in NBMA mode")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Qing Deng <i@moy.cat>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netvsc_device_remove() calls vunmap() inside which should not be
called in the interrupt context. Current code calls hv_unmap_memory()
in the free_netvsc_device() which is rcu callback and maybe called
in the interrupt context. This will trigger BUG_ON(in_interrupt())
in the vunmap(). Fix it via moving hv_unmap_memory() to netvsc_device_
remove().

Fixes: 846da38d ("net: netvsc: Add Isolation VM support for netvsc driver")
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
1GbE Intel Wired LAN Driver Updates 2022-02-07

Corinna Vinschen says:

Fix the kernel warning "Missing unregister, handled but fix driver"
when running, e.g.,

  $ ethtool -G eth0 rx 1024

on igc.  Remove memset hack from igb and align igb code to igc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Document Gigabit Ethernet IP found on RZ/G2UL SoC. Gigabit Ethernet
Interface is identical to one found on the RZ/G2L SoC. No driver changes
are required as generic compatible string "renesas,rzg2l-gbeth" will be
used as a fallback.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>